Chicago Electric MIG 180 Installation guide

Type
Installation guide
Chicago Electric MIG 180
Gun Install
Step 1
First you will need to remove all the side panels on your machine. This is
necessary to access everything for this install.
Step 2
On the side with your wire feeder, you will need to remove the four screws that
hold your gun to the wire feeder.
Step 3
On the same side of the machine you will need to disconnect the gas hose from
the push-lock fitting. To do so you will push the plastic collar of the fitting toward
the back of the machine and gently pull the hose out toward the front of the
machine.
Step 4
You will then disconnect your guns power cable located below your wire feed
mechanism. This cable is held in by one of two knobs, depending on if you have
switched your polarity from the factory set reverse polarity. You will remove the
knob that holds the cable with the red sheathing. On our machine this would be
the cable on the right (negative side) as our machine has not been changed from
the original factory setup. If you are running solid core wire you may have
switched this cable to the positive side. Remove the correct knob and remove the
cable from the post (this will be necessary to pull the cable out through the inside
of the cabinet).
Step 5
Now you will go to the other side of the machine (referred to as the “inside” for
the remainder of this walk-through). On the inside you will need to locate where
your guns trigger wires, power cable, and gas hose come through from the wire
feed side. This hole will be just on the other side of the wire feed mechanism that
you just removed the 4 screws from.
Once
you have located this hole you will see 3 things, the gas hose (clear vinyl
hose), power cable (this will be the bigger of the wires and it will be round), and
the trigger wires (slightly thinner than the power cable and also it will have a
flatter shape compared to the power cable).
Step 6
Now that you have located the above mentioned hole and wires, the next step
will be to follow the trigger wires to the computer board in your machine. The
trigger wires are hard wired into a 4 wire plug in your machine. The trigger wires
will be the two covered in the black insulation as indicated below. You will want
to cut the zip tie holding all the wires together and then cut the trigger wires,
leave plenty of wire on the plug we will be attaching spade terminals to them
next. The other two individual wires run to a small step-down transformer DO
NOT CUT THESE.
Step7
With the segments of wires you left on the plug, strip the ends and you will attach
two male spade terminals to the ends. You can also use butt connectors or solder
them together but we prefer to use spade terminals in case there is ever a time
where the gun needs to be removed again.
Step 8
You should now have everything that runs to the gun detached from the machine.
Pull the gas hose, power cable, and trigger wires through the hole that leads from
the inside to the wire feed side. Once you have those through, you should be able
to easily pull the gun out from the face of the machine.
Step 9
With your old gun out we can start with installing your new YESWELDER YW-207
or YW-208 gun. You will put your gun through the face of the machine just as the
previous one was. The power cable, trigger wires, and gas hose will feed back
through the hole to the inside of the machine (disregard the liner for the time
being), make sure your strain relief is facing the correct direction when installing
the gun.
Step 10
Once your trigger wires, power cable, and hose are on the inside of the machine
you will route your gas hose the same way it was before you removed it and
insert it firmly into the quick disconnect fitting. The trigger wires and power cable
will run down behind the board.
Step 11
The trigger wires will lead back down to the computer board you cut the previous
trigger wires from. You will then plug the trigger wires on your new gun into the
newly attached spade terminals (orientation of these two wires is irrelevant).
Step 12
The power cable will run down and back out the hole that leads to the wire feed
side. You will then return the cable to the terminal you removed it from. Our
machine pictured is still set to the factory set reverse polarity.
Step 13
The steel cable sticking out the back of the gun with the hose and wires is your
liner, this is what guides your welding wire to the tip of the gun and you will need
to trim this to fit in the wire feeder. The liner should reach as close to the drive
roll as possible without touching it, use your previous gun as reference to trim it.
Once
the liner is trimmed to the correct length you can then set the gun end and
liner in place and replace the cover (the one with 4 screws that you removed at
the beginning of this walk-through) that holds your gun to the wire feed
mechanism. The liner and gun must remain in their intended grooves or your
machine will not function properly. This can be tricky and can be made easier by
laying the machine on its side (wire feed side facing up).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Chicago Electric MIG 180 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI