SMARTCORE LX55805009 User manual

Brand: SMARTCORE

Model: LX55805009

Type: User manual

Technical Service Bulletin 1/19 | 1/3

For Additional Help, Call 1-800-355-7429

HARDWOOD MAINTENANCE

New hardwood floors represent a substantial flooring investment and with

proper care the appearance and performance of your hardwood floor can be

maintained over time.

A total care program consists of key areas:

1. Post Construction Maintenance

2. Preventative Maintenance

3. Routine Maintenance

4. Spot and Spill Removal

POST CONSTRUCTION MAINTENANCE

• Dry mop floor using a micro fiber mop pad or appropriate floor vacuum

to remove dust particulate from the floor.

• Spray neutral pH cleaner, such as Encore COREtec cleaner, onto the

floor in manageable area (spray mist will dry quickly). Use a micro fiber

damp mop pad to mop the floor with cleaner. If pad becomes dirty, be

sure to replace the pad with a new micro fiber wet mop pad. Work

floor in sections.

• Always rinse the floor by spray misting water on a flat micro fiber mop

pad meant for wet mopping (make sure there is no dripping water).

In the event where dry wall dust/construction dust is mopped with water

only, a residue film will appear on the floor after drying. Use the process

below to remove the film from the floor.

PROCESS TO REMOVE CONSTRUCTION RESIDUE OR

CLOUDY FILM FROM HARDWOOD FLOORING

1. Dry mop floor to remove any construction dust or exterior soil tracked

onto the flooring. Use micro fiber dry mop pad. If micro fiber dry mop pad

gets dirty, replace pad with a clean pad.

2. Spray neutral pH cleaner, such as Encore COREtec cleaner, onto the floor

in manageable area (spray mist will dry quickly). Work floor in sections. For

embossed or textured flooring, use a cylindrical brush scrubber, such as

Technical Service Bulletin 1/19 | 2/3

For Additional Help, Call 1-800-355-7429

the Clark MA10 12E Scrubber and a neutral pH cleaner applied to the floor

to remove the residue film.

3. Spray mist water on a microfiber mop pad meant for wet mopping so it is

damp (make sure there is no dripping water). Mop the floor to remove any

remaining residue from the flooring. When wet mop pad becomes dirty, be

sure to replace the pad with a new micro fiber wet mop pad.

4. Repeat steps #2 and #3, if necessary.

5. When the hardwood flooring is cleaned properly, the floor will have the

same visual as right out of the box!

PREVENTATIVE MAINTENANCE

• Always protect floors from direct exposure of sunlight that can cause the

wood or stain to change colors. Warranties do not cover damage from UV

exposure. Recommended humidity levels are between 35% R.H.- 55% R.H.

• Protect floors when moving heavy objects to prevent permanent scratches

and tears. The use of Ram Board or equivalent and cardboard are

examples of protective barriers.

• Use appropriate wide floor protectors under tables, chairs, and any other

heavy home furnishing to avoid permanent damage. As a rule, the heavier

the object, the wider the floor protector.

• Walk-off mats should be used at all entrances to absorb soil and moisture.

The use of appropriate mats will help avoid scratches and damages to

the floor. If mats are placed directly on top of the hardwood floors, use

proper indoor mats. Mats that can trap moisture underneath have

potential to cause possible discoloration. Latex and rubber backings

should not be used.

• Area rugs are recommended in high traffic and pivot areas. Avoid shoes

with spiked or damaged heels. Also keep pets’ paws and nails cleaned

and trimmed.

ROUTINE MAINTENANCE

• Daily removal of dirt and dust is important to prevent particles from

abrading the floor’s surface. Sweeping, dust mopping, and vacuuming

are recommendations to remove soil particles that can result in scratches

and worn appearances. Do not use vacuums with rotating beater bars on

hard surfaces.

Technical Service Bulletin 1/19 | 3/3

For Additional Help, Call 1-800-355-7429

• Encore COREtec cleaner is recommended for general spotting

and cleaning.

• Periodic cleaning will be necessary to help maintain the floor’s appearance.

Always pre-vacuum or dust mop before any type of cleaning. Encore

COREtec cleaner or appropriate hardwood floor cleaning agents (neutral

pH cleaners) are recommended.

• Do not use abrasive cleaners or cleaning agents that leave dull residues on

the surface of the floors. Never wet mop the floor with water and do not

allow excess cleaner to remain on the floor’s surface as this may

permanently damage the wood.

• Steam cleaners are not recommended.

• It is recommended to use a flat microfiber damp mop pad when mopping

the floor using a neutral pH cleaner, such as Encore COREtec cleaner. Do

not use a mop and bucket system.

• Expedite drying with air movers or fans.

• Do not use oil soaps, liquid or paste wax products, or cleaners with citrus

type oils, Tung oils, silicon or ammoniated products as well as 2-in-1

cleaners with polish additives. Problems from these type products can

affect the floor, which would not be considered in the warranty.

SPOT & SPILL REMOVAL

• Remove wet spills promptly by blotting with white paper or cloth towels.

• Dried spots should be removed by Encore COREtec cleaner with gentle

agitation from a clean towel or cloth. Always blot dry.

• Do not use detergents or abrasive cleaners since these products can result

in a dull residue and appearance.

• Use rubbing alcohol (isopropyl alcohol) with a clean white cloth for

spots requiring a solvent type cleaner that hardwood cleaning agents

cannot remove.

Please note that some stain conditions may become permanent.

SMARTCORE LX55805009 User manual

SMARTCORE LX55805009 User manual

SMARTCORE LX55805009 User manual

Related papers

Other documents