Musical Fidelity X-10v3 User manual

Brand
Musical Fidelity
Model
X-10v3
Type
User manual

This manual is also suitable for

Musical Fidelity X-10v3 is a high-quality tube output buffer that can greatly enhance the sound quality of your audio system. It features a wide frequency response, low distortion, and a high signal-to-noise ratio. The X-10v3 is easy to use and can be connected to a variety of audio sources, including CD players, DACs, and computers. It is also equipped with a loop output that allows you to connect additional audio equipment, such as an equalizer or headphone amplifier. The X-10v3 is a great way to improve the sound quality of your music, and it is sure to provide you with many years of listening enjoyment.

Musical Fidelity X-10v3 is a high-quality tube output buffer that can greatly enhance the sound quality of your audio system. It features a wide frequency response, low distortion, and a high signal-to-noise ratio. The X-10v3 is easy to use and can be connected to a variety of audio sources, including CD players, DACs, and computers. It is also equipped with a loop output that allows you to connect additional audio equipment, such as an equalizer or headphone amplifier. The X-10v3 is a great way to improve the sound quality of your music, and it is sure to provide you with many years of listening enjoyment.

X-10 V
3
Issue 2 May 2004
TUBE OUTPUT BUFFER
Instructions for use
SPECIFICATIONS
Musical Fidelity reserves the right to make improvements which
may result in specification or feature changes without notice.
Input impedance 470KOhms
Output impedance <33 Ohms
THD <0.004% 10Hz to 20kHz
Frequency response 20Hz to 65kHz +0, -0.5dB
Crosstalk better than 80dB, 20Hz to 20kHz
S/N ratio >93dB unweighted ref. full output
>106dB "A" weighted ref. full output
Valve (tube) type 6112 (two)
Power requirement 12 - 0 - 12Volts AC 500mA
(via mains adaptor supplied)
Dimensions 180mm (7.1") wide
88.2mm (3.5") high including feet
218mm (8.6") deep including
RCA sockets
Weights Unit, net : 2.5kg(5lbs 8oz)
Adapter, net :0.45kg(1lb)
Total packed :3.1kg(6lbs 13oz)
X-10 V
3
Issue 2 May 2004
Introduction
Thank you for purchasing the X-10 V
3
Tube Output Buffer. We sincerely
hope that it will bring you many years of outstanding listening pleasure.
Installation Precautions
Your new X-10 V
3
is designed and built to provide trouble-free performance,
but as with all electronic devices, it is necessary to observe a few precautions :
n Do not use the X-10 V
3
near water. The unit must not be exposed
to dripping or splashing and no objects filled with liquids, such as
vases, must be placed on the unit.
n Keep the X-10 V
3
away from heat such as radiators. No naked flame
sources, such as lighted candles, should be placed on the unit.
n Only use the mains adaptor provided. The use of other adaptors
could seriously damage your X-10 V
3
.
n Place all connecting cables where they are not likely to be walked on
or trapped by items placed on them.
n X-10 V
3
will operate in accordance with its specifications within the
following environmental range :
Temperature5 to 45 degrees Celsius
Humidity 10 to 90% non condensing
This Hi-Fi product has been tested to ensure that its operation is not adverse-
ly affected by normal background levels of Radio Frequency Interference
(R.F.I.), and that it does not itself generate excessive amounts of interference.
However, if a problem persists, please contact your Musical Fidelity agent.
Never open the case of the X-10 V
3
yourself, as this will invalidate the guar-
antee. There are no user adjustments inside. Please refer all service work to
an authorised Musical Fidelity agent.
Connections
All connections should be made before the mains adaptor is plugged in.
Using good quality RCA leads (not supplied), connect the left and right
outputs from your CD player or other audio source to the X-10 V
3
LINE
INPUTsockets. The LOOP OUTPUT
sockets are simply duplicates of
the LINE INPUT, and are directly connected internally. This is to allow
further connection to other audio equipment if required.
Now connect your X-10 V
3
left and right OUTPUTSto the CD or auxil
-
iary inputs of your amplifier system.
Input from CD player
or other audio source
Optional output to other
audio equipment
AC inlet from
mains adaptor
Connect to amplifier
Plug the AC connector lead from the power supply unit into the X-10 V
3
’s
inlet socket, and plug the power supply itself into a convenient wall mains
outlet. The blue LEDon the front panel will light to confirm the unit is
ready for use. Allow a minute or so for the valves (tubes) to warm up, then
sit back and enjoy the music.
This product has been designed so that it may be left on indefinitely, but
please note that the mains adapter may become warm to the touch - this is
normal.
BUILT IN TAIWAN
  • Page 1 1
  • Page 2 2

Musical Fidelity X-10v3 User manual

Brand
Musical Fidelity
Model
X-10v3
Type
User manual
This manual is also suitable for

Musical Fidelity X-10v3 is a high-quality tube output buffer that can greatly enhance the sound quality of your audio system. It features a wide frequency response, low distortion, and a high signal-to-noise ratio. The X-10v3 is easy to use and can be connected to a variety of audio sources, including CD players, DACs, and computers. It is also equipped with a loop output that allows you to connect additional audio equipment, such as an equalizer or headphone amplifier. The X-10v3 is a great way to improve the sound quality of your music, and it is sure to provide you with many years of listening enjoyment.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents