Aspace Warwick User manual

Category
Baby furniture
Type
User manual
Warwick
High Sleeper
Code: 2807 - 2806
IMPORTANT-READ CAREFULLY-RETAIN FOR FUTURE REFERENCE
11. Storage Drawer Assembly Continued.
You need: 8x Screws, 4x Castors and a Screwdriver
Carefully fit the Base by sliding it downwards into the grooves on the inside faces of the sides,
also making sure that it is fully engaged into the groove in the back of the Drawer Front. Once
the Base is correctly in position, fit the back onto the assembly by locating the exposed heads
of the fitted Dowels and Cam Pins into the holes in the sides and Brace. Once the parts are
aligned and engaged correctly, tighten each Cam to secure the back (don't forget the Cam in
the Brace).
11
Carefully flip the assembly over and fit the 4x Castors to the bottom of the Drawer as shown
using 2x Screws for each castor as shown.
Please now recheck that all fittings are properly tightened and finally place each
in your required position under the Day Bed.
Orientation Options
Please refer to the orientation option images below to help you decide and understand
which way to construct the product.
Orientation Option A (Including Desk)
Orientation Option B (Including Desk)
If the Desk is not used, the Day Ded can also be positioned parallel to the Bed
These are the only two recommended options for orientation.
Ladder and Desk
positioned on the
Right, Day Bed
positioned on the
Left.
Ladder and Desk
positioned on the
Left, Day Bed
positioned on the
Right.
10
1
You need: 10x Cam
Pins, 6x Dowels and a
Screwdriver.
Lay the parts on a soft
level surface such as a
carpeted floor and
screw Cam Pins into
the smaller holes on
the reverse of the front
and back as shown
(A). Fit 10x Cams into
the large holes in the
Sides and Brace as
shown (B) and fit 6x
Dowels into the end
edges of both Sides
and Brace as shown
(C).
Parts Check List (Storage Drawers - Per Drawer)
10. Assemble the Storage Drawers (Per Drawer)
4x Castors
10x Cam Pins
10x Cams
6x Dowels
8x Screws
Front
Sides x2
Back
Brace
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
C
C
C
C
A
A
C
Carefully fit the Sides onto the front, ensuring that the grooves and the Cams are facing
inwards. Ensure that the exposed heads of the now fitted Dowels and Cam Pins fully
engage into their corresponding holes as shown. Once all is engaged and aligned, tighten
each Cam clockwise to secure the parts together.
2
Product Safety
Care of your Product
Welcome
Product Care
Customer Service 0345 872 2400
About ASPACE
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Periodically check all fittings to ensure that none have come loose.
The furniture must be set up on an even and stable surface.
Keep away from direct sources of heat, such as electric, gas or coal fires.
Do not allow children to climb on the furniture. Using this furniture other than for its intended
purpose could cause damage to the structure or serious injury to your child.
The High Sleeper should not be used if any structural part is broken or missing
The upper bunk is not suitable for children under six years old due to the risk of injury from falls.
Do not attach items such as ropes, strings, cords, harnesses or belts etc to avoid the risk of
strangulation.
Warning: Children can become trapped between the bed and the wall. To avoid the risk of serious
injury the distance between the top safety barrier and the wall must not exceed 75mm or shall be more
than 230mm.
Thank you for buying the Warwick High Sleeper.
Before beginning assembly, please take a few quiet minutes to read these instructions.
Lay the parts out on a clean, soft, flat surface (such as a carpeted floor) and compare with the parts
check list on the next page. Do not throw away any packaging until you are sure you have all parts.
If, for any reason, you wish to return the product, you must disassemble the components and use the
original packaging.
The product must be assembled by an adult. There are small parts: keep small children clear of the
assembly area. Some stages of assembly require more than one person.
This product is designed to conform to BSEN747:1 2012
The MAXIMUM thickness of the UPPER BUNK mattress is 20cm.
This information is identified on the product label fitted to the bed.
The recommended size of the mattress is 191cm x 90cm (6`3” x 3`0)
Ÿ
Ÿ
Clean your High Sleeper by wiping with a damp cloth & drying with a soft cloth. Never clean with
abrasives, chemical cleaner or household polishes.
Take care when handling or moving the furniture. Careless handling can damage wooden furniture,
Try to lift rather than drag.
If you have a problem with this product, please call our Customer Service Team, who will be glad to
help.
We can usually provide replacement and / or spare parts promptly; it will help us if you can identify the
specific part using the check list in the next section.
9
9. Assemble the Day Bed.
You need: 8x Bolts (60mm), 4x Bolts (50mm), 4x Barrel Nuts, 6x Screws (25mm) an Allen Key and a
Screwdriver.
With the help of another person(s) align and fit the Mattress Rails (
lso fit the Back Panel to the Ends using 4x Bolts (50mm) and 4x Barrel
Nuts. Please note: The positions and orientation of the Mattress support rails as shown (A).
as below) using the 8x Bolts
(60mm) and 8x Barrel Nuts. A
Fully
support each part and insert each bolt through the holes in the corresponding components and then
finally engaging into the hole in the side of the barrel nut (B). Once each bolt is engaged, tighten with
an allen key. You may find this process easier if a screwdriver is used to align the barrel nut holes (C).
Parts Check List (Day Bed) Images not to scale
Assembly (Day Bed)
You will also need a screwdriver
(Not supplied)
12x Barrel Nuts
8x Bolts (60mm)
2x Ends 1x Mattress Base
1x Back Panel
6x Screws (25mm)
1x Back Mattress Rail
1x Front Mattress Rail
Carefully lift the Mattress
base onto the Day Bed,
making sure that the
webbing is facing
downwards. Spread the
slats out along the length of
the mattress support rails
and align the end and
middle slats with the pilot
holes in the support rails
below. Once all is aligned,
secure the Base in position
using the 6x Screws (25mm)
as shown.
A A
B C
Mattress Support Rail
With the help of another person, carefully lift the Day Bed into your position.
4x Bolts (50mm)
Most of us at ASPACE are parents too, so we know how important it is to give children a
ladder, wardrobe door and bookshelf designed by our team in the UK.
ASPACE bedrooms are packed with creativity, fun and inspiration; from gorgeous bedroom
sets and beautiful bedding, to clever storage and creative accessories, we make sure
everything we sell is built to last, and delivered with love.
Most of us at ASPACE are parents too, so we know how important it is to give children a
comfortable, secure and individual space where they can sleep, learn and play. We’ve been
kitting out children’s bedrooms with clever furniture ideas for over 20 years, with every bunk
ladder, wardrobe door and bookshelf designed by our team in the UK.
3
8
Parts Check List (Bed).
2x Allen Key
Ladder End x1
Mattress Base x1
Lower Rear Brace x1
Ladder Right Mattress Rail x1
Safety Rail Stile x1
Front Safety Rail x1
Rear Safety Rail x1
Ladder Legs x2
Ladder Hooks x2
Ladder Left Mattress Rail x1
4x Bolts for Rails (50mm)
18x Bolts for Bed (110mm)
34x Screws for Mattress Base (25mm)
16x Dowels
4x Small Bolts for Ladder Hooks (20mm)
26x Barrel Nuts
2x Screws (16mm)
You will also need
a screwdriver (Not supplied)
8. Fit the Desk.
You need: 6x Bolts (35mm), 2x Screw Bolts (50mm) and an Allen Key
NOTE: Please refer to the orientation option images at the front of this user guide to
help you decide and understand which way to position the Desk.
A - The Desk may be mounted either on the left or the right. Using 2x Screw Bolts (50mm),
attach the Desk Support to the Lower Rear Brace as shown.
6x Bolts (35mm)
2x Screw Bolts (50mm)
B - Place the Desk Top on the frame formed by the Lower Rail of the Bed End, the Rear
Brace and the Desk Support as shown. Use the Remaining 6x Bolts (35mm) and an Allen
Key to attach to the metal inserts beneath.
Parts Check List (Desk)
Assembly (Desk)
A B
1x Desk Top
1x Desk Support
(Left & Right)
Ladder Treads x4
8x Bolts for Ladder (60mm)
CR
Non Ladder End x1
Fittngs for the Desk and Day bed are shown on pages 8 & 9
Images not to scale
2x felt strips
4
7
Assembly (Bed).
1. Attach the rear Rails to the Sides.
You need: 12x Bolts (110mm), 12x Barrel nuts, 1x Allen Key and possibly a Screwdriver.
NOTE: Please refer to the orientation option images at the front of this user guide to
help you decide and understand which way to construct the product. This guide shows
construction with the Ladder and Desk positioned on the Right if selected. (Option A).
For Option B the construction must be mirrored.
This construction should be attempted by at least two people.
Lay the Rear Safety Rail, Ladder Left Mattress Rail and Lower Rear Brace on a soft level floor,
with the holes near the ends of the Rails facing upwards. The Mattress support rail must be
orientated at the bottom as shown (X) in Fig 1.1.
Align the Ends Using 12x Barrel nuts and 12x Bolts (110mm) as shown below (see Fig 1.2). It
is critical that the holes in the Lower Rear Brace and Mattress Rail are always positioned
closer to the Ladder End.
Push the Bolts through the holes in the Ends and into the ends of the Rails, locating the Bolts
into the holes on the side of the Barrel Nuts. (Barrel nut holes can be aligned with a
Screwdriver) Once in position tighten the Bolts using the Allen Key to secure.
The mattress
support rail
(X) must be
facing
upwards and
positioned at
the bottom as
shown.
The Lower Rear Brace and Rear Safety Rail can be orientated so
that the Barrel Nut holes can face inwards or outwards.
Holes Positioned
A
B
Fig 1.1
X
X
X
Fig 1.2
closer to Ladder End
Ladder End
Non Ladder End
Ladder End must be
positioned on the right
to enable the desk to
be fitted on the right.
7. Attach the Ladder
You need: 2x Ladder Hooks, 4x Small Bolts (20mm), 2x Screws (16mm) 2 x felt strips and a
Screwdriver.
A - A pair of inserts will be found near the top of each Ladder upright. Attach the Ladder Hooks
as shown, screwing the 4x bolts (20mm) into the inserts holes. Tighten fully. Now fit the 2 x felt
pads to the inside of the hooks.(paint protection)
B - Hook the Ladder Hooks over the Front Mattress Rail between the Safety Rail Stile and the
bedpost. Make sure the Ladder is even on the floor and Rail.
Fit the 2x Screws (16mm) through the ends of the Ladder Hooks and into the pilot holes on
the inside face of the Mattress Rail as shown.
6. Construct the Ladder.
You need: 8x Bolts (60mm), 8x Barrel Nuts, an Allen Key and a Screwdriver
(not supplied).
Lay both Ladder Legs and all four Ladder Treads on a soft floor. Use the holes on the back
edge of each Leg (X) as a reference point to ensure that both legs are orientated correctly.
Also ensure that the Barrel Nut holes on the back face of each Ladder Tread face upwards at
that the rounded edge of each tread is orientated as shown.
Once all is correctly aligned (as below) push the Bolts through the holes in the Ladder sides
and into the ends of the each Tread, locating the Bolts into the holes on the side of the Barrel
Nuts. (Barrel nut holes can be aligned with a Screwdriver). Ensure the Dowels on the ends of
the Treads also locate correctly. Once in position tighten the Bolts using the Allen Key to
secure.
X
Ensure that the rounded edge
of the tread is orientated as shown
5
6
4. Attach the Front Safety Rail.
You need: 2x Bolts (50mm), 2x Bolts (110mm), 2x Barrel Nuts and an Allen Key.
Attach the Front Safety Rail to the End using 2x Bolts (110mm) and Barrel Nuts. Attach the
other End to the Safety Rail Stile using the remaining 2x Bolts (50mm), tighten all the fittings
to secure the structure.
3. Fit the Mattress Base & .
You need: 34x Screws (25mm), 2x Bolts (50mm), an Allen Key and a Screwdriver.
Attach the Safety Rail Stile
Lower the Mattress Base onto the top of the support rails. Spread the slats out evenly on the
mattress support rails, taking particular care that the end slats are placed as near to the Ends
as possible. Use the 34x screws (25mm) to fix all Mattress Base slats onto the mattress
support rails below. Some initial pressure will be required for screws to ‘bite’. Please note: the
Mattress Base must have every slat screwed down.
Attach the Safety Rail Stile to the pair of holes in the Front Mattress Rail closest to the ladder
end using 2 of the Bolts (50mm) and an Allen Key.
2. Attach The Ladder Right Mattress Rail.
You need: 4x Bolts (110mm), 4x Barrel Nuts and an Allen Key
NOTE: With a minimum of two people carefully stand the assembly upright.
Fit the Ladder Right Mattress Rail using 4x Bolts (110mm) and 4x Barrel Nuts as before.
Mattress support rail must be at the bottom of the Rail and facing inwards.
5. Prepare the Ladder Treads.
You need: 16x Dowels (30mm).
Prepare each ladder tread by carefully inserting 4x Dowels into the larger holes in the end of
each tread as shown. Ensure each Dowel is fully fitted into each hole.
All slats must be screwed down
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Aspace Warwick User manual

Category
Baby furniture
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI