DX8100 AND KBD300A, STANDARD AND SHIFT MODES
DX8100_KBD300A_STANDARD_SHIFT_MODE_PAGE_1_OF_2
Pelco and the Pelco logo are registered trademarks of Pelco.
Information subject to change without notification.
Copyright 2006, Pelco. All rights reserved.
©
World Headquarters
3500 Pelco Way, Clovis, California 93612 USA
USA & Canada Tel: 866/587-2503 Fax: 800/289-9150
International Tel: 1-559/348-5504 Fax: 1-559/348-1120
www.pelco.com
DX8100 AND KBD300A, STANDARD AND SHIFT MODES
The KBD300A allows you to operate certain DX8100 live view display functions and control camera PTZ operations from a keyboard rather than a
mouse.
When connected to the DX8100 server, the KBD300A supports two modes: the Standard mode and the Shift mode. The Shift mode is entered by
pressing the Shift button and is indicated by the lighting of the shift button LED. For information about how to operate the KB
D300A,
refer to the
KBD300A Universal Keyboard Installation/Operation manual.
KBD300A STANDARD MODE OPERATIONAL FEATURES
The KBD300A Standard mode allows you to control certain DX8100 operation features in the view pane from the keyboard.
This section describes the KBD300A Standard mode features/functions. The Standard mode is effective within the DX8100 view pane. You can
program camera presets and patterns, operate the camera PTZ features, and assign cameras to panes. For detailed information about how to
operate the KBD300A, refer to the KBD300A Universal Keyboard Installation/Operation manual.
The following table describes the KBD300A Standard mode operational features specific for the DX8100 server.
To place the KBD300A in the standard mode:
Keyboard Control Action
Joystick Controls the camera’s PTZ operation.
Number + PRESET (short) Moves camera to the programmed preset position.
Number + PRESET (long) Programs the current camera position to the desired preset number.
Number + PATTERN (long) Starts the pattern record mode.
ACK Stops the pattern record mode.
Number + PATTERN Runs the desired pattern.
Number + AUX ON/AUX OFF Turns the specified auxiliary output on or off.
Number + MON Assigns the selected camera to the desired view pane. The active view pane is highlighted.
On the KBD300A keyboard, press the SHIFT button.
The LED indicator should be off.
DX8100 AND KBD300A, STANDARD AND SHIFT MODES
DX8100_KBD300A_STANDARD_SHIFT_MODE_PAGE_2_OF_2
Pelco and the Pelco logo are registered trademarks of Pelco.
Information subject to change without notification.
Copyright 2006, Pelco. All rights reserved.
©
World Headquart ers
3500 Pelco W ay, Clovis, California 93612 USA
USA & Canada Tel: 866/587-2503 Fax: 800/289-9150
International Tel: 1-559/348-5504 Fax: 1-559/348-1120
www.pelco.com
DX8100 AND KBD300A, STANDARD AND SHIFT MODES
(continued)
KBD300A SHIFT MODE OPERATIONAL FEATURES
The KBD300A Shift mode allows you to control certain DX8100 operation features in the Site tree from the keyboard.
This section describes the KBD300A Shift mode features/functions. The
Shift mode is effective within the DX8100 Site tree. You can move the
cursor to select elements within the Site tree, expand/collapse elemen
ts, and select the display division. For detailed information about how to
operate the KBD300A, refer to KBD300A Universal Keyboard Installat
ion/Operation manual.
The following table describes the KBD300A Shift mode operational features specific to the DX8100 server
.
To place the KBD300A in the shift mode:
Keyboard Control Action
Joystick Activity within the DX8100 Site tree:
• Up/down direction: Moves the cu
rsor vertically through each element in the Site tree.
An element is a DX8100 site, camera within each DX8100 site, or Alarm,
ATM/POS, and relay within each
DX8100 site.
If an element is expanded, the joystick moves the cursor vertically through the objects of that element.
•
Left/right direction:
– Right: Expands an element to display objects con
tained under the element.
– Left: Collapses an element and hides i
ts objects. Select a camera/unit at the tree.
Number + CAM Expands the Site tree and selects the first camera in each DX8100 site. For
example, if there are two sites with one
named
DX8100 site 1 and the other named DX8100 site 2:
•
Pressing 1 + CAM expands the Site tree for DX8100 site 1 and selects the first camera. But it does not assign
the selected camera to a view pane or display video.
• Pressing 2 + CAM expands the Site tree for DX8100 site 2 and selects
the first camera. But it does not assign
the selected camera to a view pane or display video.
F2, F3, ON, OFF Cameras are assigned numerically 1–16 to the respectively number video. These controls display DX8100 video in
the following divisions:
• F2/OFF: Single-division view
• F3/MOM: 4-division view
•
AUX ON: 9-division view
• AUX OFF: 16-division view
Repeatedly pressing a button causes the DX8100 to cycle through the display of the remaining panels.
On the KBD300A keyboard, press the SHIFT button
.
The LED indicator should be on.
/