DK Digital TS-3000 Owner's manual

Brand: DK Digital

Model: TS-3000

Category: Alarm clocks

Type: Owner's manual

Many thanks . . .

…that you have decided in favour of one of our products.

For your own safety and for helping you to understand

the complete functional range, please read these

instructions carefully and keep them for a later

consultation. Should you sell the appliance please give

the buyer the manual to take it with him.

www.dk-digital.com

-2-

General things

•

Your TS-3000 offers four different display functions:

- Time with alarm function

- Temperature

- Date with weekday

- Timer.

•

By carefully tapping on the display, you transfer the

display to the next function. After each switch over, the

display is shortly illuminated in another colour. You can

switch off this display illumination by pushing the

switch “Back light” on the bottom side of the appliance

into the position “OFF”.

•

With the switch “MODE LOCK” you can determine

whether after having shown the temperature, timer or

date display in each case for ten seconds, the appliance

is to display the time again (Off) or to permanently

maintain the respective function display (On).

•

We have inserted a transparent

protection foil between the battery

poles so that the batteries are still

fresh at their first use (see next

page). In order to start-up the

clock, please pull out the

protection foil. In doing so, the

display should be activated

immediately.

-3-

DCF77 signal

This product is designed to automatically synchronize the

current time and date when it is used within range of the

radio signal DCF77 generated from Frankfurt Germany

for Central Europe.

Reception can be affected by a number of factors. For

best reception, place the clock away from metal objects

and electrical appliances. Other causes for signal

interference include electrical transmission tower and

steel reinforced construction. Reception is ideal when

placed near a window.

When the clock is receiving the signal, the radio reception

symbol starts to blink. Generally, complete reception

takes around 2 to 10 minutes, depending on the strength

of the signal.

Below are three different radio reception description on

the screen:

After complete radio reception, radio reception symbol

appears without blinking.

-4-

Setting the time

If the clock can’t receive the DCF77 signal you can set the

time manually:

•

Tap the display so many times until the time is shown.

•

Hold the SET key for two seconds. Now, the hour value

is flashing and you can enter the current time by using

the 5 or 6 key.

•

Then, you push the SET key once again. Now, the minute

value is flashing and you can enter the minute of the

current time by using the 5 or 6 key.

• Push the SET key once again in order to save settings.

If no key is pushed for one minute, the appliance saves

the current setting.

•

After completion of the time setting, you can change

the time display to 12 hours or 24 hours mode by

pushing the 5 or 6 key once.

Setting the alarm time

Make shure the MODE LOCK switch is in OFF position.

•

If necessary, tap the display so many times until the

time is shown.

-5-

•

Push the AL(ARM) key. The AL sign appears in the

display. You have now ten seconds for setting the

alarm time. If this time expires, the appliance returns

to the time display.

•

Now, push the SET key and the hour value is flashing.

By means of the 5 or 6 key, you can set the hour of

the desired alarm time.

•

Push the SET key once again and the minute value is

flashing. You can now set the minute of the desired

alarm time by using the 5 or 6 key.

•

Finally, push the SET key. The alarm time is now saved

and the alarm clock symbol appears in the display.

After ten seconds, the appliance returns to the time

display. You can have the alarm time displayed at any

time by pushing the ALARM key.

•

At the set time, the alarm tone is activated and will be

peeping for a maximum of one minute or until you press

any key. The alarm time is, however, saved. In order to

switch the alarm function off, push the ALARM key once

and then hold this key for two seconds. The alarm clock

symbol disappears.

•

If you tap the display when the alarm chimes, the

alarm is muted for 5 minutes. The Z

symbol shows

that the snooze function is activated. Press any key

except the MODE key to cancel the snooze mode.

-6-

Temperature display

•

If you tap the display during the time display once, the

display changes to the current room temperature.

•

Push the 5 or 6 key during the temperature display for

changing from Celsius to Fahrenheit as measuring unit.

Date display

•

If you tap the display during the temperature display

once, the display changes to the date. Normally, the

DCF77 signal transmits the current date as well.

•

If the device does not receive a DCF77 signal, you can

set the date manually. For setting the correct date,

hold the SET key for two seconds. Now, the year is

flashing for one minute and you can change it by

means of the 5 or 6 key. Then, you push the SET key

and the number for the month is flashing which you

can again set with the 5 or 6 key. Push the SET key

once again for setting the day in the same way. Push

the SET key for the last time for completing your

setting.

Timer function

•

If you tap the display during the date display once, the

appliance changes to the timer operation. With it, you

-7-

can program a split-second “countdown” of up to 180

minutes at the end of which an alarm signal resounds.

•

For setting the desired timer time, push the SET key

during the timer display. Now, the minutes of the timer

time are flashing and you can set them by means of the

5 or 6 key. Then, you push the SET key once again

and the seconds of the timer time are flashing which

you can again set by means of the 5 or 6 key. Finally

push the SET key.

•

In order to start the “countdown”, push the 6 key. If

you want to stop it, push the 6 key again, also for

continuing.

• After the timer time has expired, the alarm signal

resounds which can be stopped by tapping the display.

The timer time is, however, saved.

Changing the batteries

If the display looks blurred or the display remains totally

dark, you must replace the batteries. For doing so, open

the battery compartment on the bottom side of the

appliance. Remove the discharged batteries and insert

three batteries (1.5 V, size AAA) according to the layout

that is shown in the battery compartment. When doing so

look out exactly for the compliance of the correct

polarity, otherwise, the appliance will not function and

can be damaged. For a longer useful economic life, you

-8-

should use alkaline batteries. Close the battery

compartment again.

Batteries do not belong into the domestic waste.

Please turn your discharged batteries in at the

responsible collecting point or at the place where

you have bought the new ones. Never throw

batteries into fire.

If you do not use the appliance for a longer period of

time, remove the batteries from the battery

compartment in order to avoid damage due to leakage of

the batteries.

Resetting

If you want to reset all settings into the state of delivery,

push the switch behind the RESET opening on the bottom

side of the appliance with a pointed object (e.g. a

needle). You must then newly set the time and the date.

-9-

Disposal advice

When the operating life of this device has

ended it must not be disposed as domestic

waste, but in accordance with national

environmental guidelines.

-10-

-11-

We reserve the right to correct errors and make

technical alterations. This manual is copyrighted.

excerpts may be reproduced without our prior written

permission.

DK digital AG

40878 Ratingen

Germany

DK Digital TS-3000 Owner's manual

Brand: DK Digital

Model: TS-3000

Category: Alarm clocks

Type: Owner's manual

Download PDF

report

DK Digital TS-3000 Owner's manual

DK Digital TS-3000 Owner's manual

Related papers

Other documents