Sony SLV-X815PS User manual

Brand: Sony

Model: SLV-X815PS

Category: Cassette players

Type: User manual

This manual is also suitable for

Video Cassette

Recorder

Operating Instructions

3-810-473-11 (1)

SLV-X815ME

SLV-X815PS

SLV-X815SG

PAL NTSC

Introduction

WARNING

To prevent fire or shock hazard, do not expose

the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified personnel

only.

Precautions

Safety

• This VCR operates on 110 – 240 V AC,

50/60 Hz. Check that the unit’s operating

voltage is identical with your local power

supply.

• If anything falls into the cabinet, unplug the

unit and have it checked by qualified

personnel before operating it any further.

• The unit is not disconnected from the mains

as long as it is connected to the mains outlet,

even if the unit itself has been turned off.

• Unplug the unit from the wall outlet if you

do not intend to use it for an extended

period of time. To disconnect the cord, pull

it out by the plug, never by the cord.

Installing

• Allow adequate air circulation to prevent

internal heat buildup.

• Do not place the unit on surfaces (rugs,

blankets, etc.) or near materials (curtains,

draperies) that may block the ventilation

slots.

• Do not install the unit near heat sources

such as radiators or air ducts, or in a place

subject to direct sunlight, excessive dust,

mechanical vibration or shock.

• Do not install the unit in an inclined

position. It is designed to be operated in a

horizontal position only.

• Keep the unit and cassettes away from

equipment with strong magnets, such as

microwave ovens or large loudspeakers.

• Do not place heavy objects on the unit.

• If the unit is brought directly from a cold to

a warm location, moisture may condense

inside the VCR and cause damage to the

video head and tape. When you first install

the unit, or when you move it from a cold to

a warm location, wait for about one hour

before operating the unit.

Caution

Television programmes, films, video tapes and

other materials may be copyrighted.

Unauthorized recording of such material may

be contrary to the provisions of the copyright

laws. Also, use of this recorder with cable

television transmission may require

authorization from the cable television

transmitter and/or programme owner.

Compatible colour systems

This VCR is designed to record and play back

using the PAL (B/G and D/K), MESECAM (B/

G and D/K) and NTSC colour systems.

Recording of video sources based on other

colour systems cannot be guaranteed.

Introduction

Table of contents

Getting Started

Basic Operations

18 Playing a tape

21 Recording TV programmes

24 Recording TV programmes using

the timer

Additional Operations

27 Playing/searching at various

speeds

29 Recording TV programmes using

the quick timer

30 Checking/changing/cancelling

timer settings

31 Recording stereo programmes

32 Adjusting the picture

34 Changing menu options

35 Editing with another VCR

Getting Started

4 Step 1: Unpacking

5 Step 2: Setting up the remote commander

6 Step 3: Connecting the VCR

8 Step 4: Tuning your TV to the VCR

10 Step 5: Selecting a language

11 Step 6: Setting the clock

13 Step 7: Tuning the VCR

Additional Information

37 Troubleshooting

39 Specifications

40 Index to parts and controls

Back cover

Index

Getting Started

• Remote commander

• R6 (Size AA) batteries

• Aerial cable

Getting Started

Step 1

Unpacking

Check that you have received the following items with the VCR:

• Audio/video cable (3-phono to 3-

phono)

• Mains lead

• Plug adaptor (SLV-X815ME/X815SG)

Checking your model name

The instructions in this manual are for the 3 models : SLV-X815ME,

X815PS and X815SG. Check your model number by looking at the

rear panel of your VCR. The SLV-X815ME is the model used for

illustration purposes. Any difference in operation is clearly indicated

in the text, for example, “SLV-X815ME.”

Getting Started

Step 2

Setting up the remote commander

Inserting the batteries

Insert two R6 (size AA) batteries by

matching the + and – on the

batteries to the diagram inside the

battery compartment.

Using the remote commander

You can use this remote

commander to operate this

VCR and a Sony TV. Buttons on

the remote commander marked

with a dot (•) can be used to

operate your Sony TV.

To operate

the VCR

a Sony TV

Set TV / VTR to

VTR and point at the remote sensor on the VCR

TV and point at the remote sensor on the TV

Notes

• The TV/VIDEO button selects an input sourse of the TV from aerial in or line in.

The button does not control this VCR.

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove

the batteries to avoid possible damage from battery leakage.

• Do not use a new battery with an old one.

• Do not use different types of batteries.

Remote sensor

TV / VTR

Getting Started

Step 3

Connecting the VCR

to mains

AERIAL IN

Aerial cable

AERIAL OUT

AC IN

: Signal flow

OUT

AERIAL

1 Disconnect the aerial input cable from

your TV and connect it to AERIAL IN on

the rear panel of the VCR.

2 Connect AERIAL OUT of the VCR and

the aerial input of your TV using the

supplied aerial cable.

3 Connect AC IN of the VCR to the mains

using the supplied mains lead.

AERIAL

OUT

Getting Started

VIDEO

AUDIO

AUDIO VIDEO

LINE-1 IN

LINE OUT

Additional connections

To a TV that has phono type

audio/video input jacks

This additional connection

improves picture and sound quality.

Connect the TV as shown on the

right.

To a stereo system

You can improve sound quality by connecting a stereo system as shown below.

This VCR

AUDIO VIDEO

LINE-1 IN

LINE OUT

AUX IN

This VCR

Stereo system

Audio cable (not supplied)

Audio/video cable

Getting Started

1 Press ON/STANDBY to turn on the VCR.

2 Press PROGRAM +/– until “L1” appears in the display window.

3 Turn on your TV and select a programme position for video

playback.

Choose a channel between UHF 30 and 39 on the TV, where there is

no picture and no sound or only a steady rustling sound.

This channel will now be referred to as the video channel.

4 Tune the TV so that a blue screen appears on the TV screen.

Refer to your TV manual for tuning instructions.

You have now tuned your TV to the VCR. From now on, whenever

you want to play a tape, set the TV to the video channel.

If the blue screen does not appear clearly, see “To obtain a clear blue

screen” on page 9.

PROGRAM

–

Step 4

ON/STANDBY

Tuning your TV to the VCR

If you have connected your VCR to the TV using the audio/video cable, skip

this step.

ON/STANDBY

PROGRAM +/–

Getting Started

To check to see if the TV tuning is correct

Set the TV to the video channel and press PROGRAM +/– on the VCR. If

the TV screen changes to a different programme each time you press

PROGRAM +/–, the TV tuning is correct.

To obtain a clear blue screen

If the blue screen does not

appear clearly in step 4 above,

turn the RF CHANNEL screw at

the rear of the VCR with an RF

screwdriver to a position where

the TV clearly displays the blue

screen.

Selecting the TV system

For your TV to receive the correct

signal from your VCR, you must

set the TV SYSTEM switch at the

rear of the VCR to either G (for

system B/G) or K (for system D/

K). If this switch is set to the

wrong position, the sound will be

distorted.

TV SYSTEM

RF CHANNEL

Getting Started

Selecting a

language

You can change the on-screen language

from English to Chinese or Arabic.

Before you start...

• Turn on the VCR and the TV.

• Set the TV to the video channel.

1 Press MENU.

2 Press CURSOR >/. to move the cursor

(z) to LANGUAGE and press EXECUTE.

3 Press CURSOR >/. to flash the desired

language, then press EXECUTE.

ENGLISH

[ V v ]

[ EXECUTE ]

•

LANGUAGE /

ENGLISH

SELECT :

END :

[ V v ]

[ EXECUTE ]

•

Step 5

•MENU

•CURSOR

•EXECUTE

CURSOR

>/./?//

EXECUTE

•CURSOR

•EXECUTE

TIMER SET / CHECK

SET UP MENU

TUNER PRESET

CLOCK SET

SELECT : [ ]

SET : [ EXECUTE ]

LANGUAGE / /

Getting Started

1 Press MENU.

2 Press CURSOR >/. to move the cursor

(z) to CLOCK SET, then press EXECUTE.

3 Press CURSOR >/. to set the day.

The day of the week is set automatically.

4 Press CURSOR / to flash the month and

set the month using CURSOR >/..

continued

CLOCK SET

2 .1.1996 THU 0:00

SELECT

SET

[]

END : [ EXECUTE ]

CLOCK SET

1 . 1 . 1996 MON 0 : 00

SELECT

SET

[]

END : [ EXECUTE ]

Step 6

Setting the clock

You must set the time and date on the

VCR to be able to use the timer

recording features properly. You can set

the VCR clock using the on-screen

display.

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

•MENU

•CURSOR

•EXECUTE

CURSOR

>/./?//

EXECUTE

CLOCK SET

2 .1 .1996 WED 0:0052

SELECT

SET

:[ ]

[]

END : [ EXECUTE ]

TIMER SET / CHECK

SET UP MENU

TUNER PRESET

CLOCK SET

SELECT : [ ]

SET : [ EXECUTE ]

LANGUAGE / /

Getting Started

5 Set the year, hour and minutes in

sequence, using CURSOR / to flash the

item to be set, and CURSOR >/. to select

the digits.

6 Press EXECUTE to start the clock.

CLOCK SET

2 .1 .1996 WED52 5:301

SELECT

SET

:[ ]

[]

END : [ EXECUTE ]

Tip

• To change the digits during setting, press CURSOR ? to return to the item to be

changed, and select the digits using CURSOR >/..

Note

• The menu disappears automatically if you don’t proceed for more than a few

minutes.

•CURSOR

•EXECUTE

Step 6 : Setting the clock (continued)

Getting Started

1 Press MENU.

2 Press CURSOR >/. to move the cursor

(z) to TUNER PRESET, then press

EXECUTE.

TUNER PRESET PROG 1

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

SELECT

SET

[]

Tuning the VCR

First, we recommend that you preset the

receivable channels in your area using

automatic presetting. Then, if some

channels could not be preset

automatically, you can preset them

manually; if there are any unwanted

channels among the preset ones, you can

disable the channels.

Before you start…

• Turn on the VCR and the TV.

• Set the TV to the video channel.

Presetting all receivable channels automatically

Step 7

•MENU

•CURSOR

•EXECUTE

continued

CURSOR

>/./?//

EXECUTE

TIMER SET / CHECK

SET UP MENU

TUNER PRESET

CLOCK SET

SELECT : [ ]

SET : [ EXECUTE ]

LANGUAGE / /

Getting Started

3 Press CURSOR >/./?// to move the

cursor (z) to SYSTEM, then select either

B/G or D/K, whichever is applicable in

your area. If SYSTEM is set to the wrong

position, the sound will be distorted or

noisy.

4 Press CURSOR >/./?// to move the

cursor (z) to NORMAL/CATV, then select

NORM.

To preset CATV channels, select CATV.

5 Press CURSOR >/. to move the cursor

(z) to AUTO PRESET, then press

EXECUTE.

All receivable channels are preset in

numerical sequence. When no more

receivable channels can be found,

presetting stops and the picture from the

lowest numbered channel is displayed on

the TV screen.

TUNER PRESET PROG 1

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

SELECT

SET

[]

TUNER PRESET PROG 1

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

SELECT

SET

[]

Step 7 : Tuning the VCR (continued)

•CURSOR

•EXECUTE

PLEASE WAIT

TUNER PRESET PROG 1

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

Getting Started

1 Press MENU.

2 Press CURSOR >/. to move the cursor

(z) to TUNER PRESET, then press

EXECUTE.

3 Press CURSOR >/./?// to move the

cursor (z) to NORMAL/CATV, then select

NORM.

To preset CATV channels, select CATV.

continued

•MENU

•CURSOR

•EXECUTE

Presetting channels

manually

CURSOR

>/./?//

EXECUTE

PROG+/–

TUNER PRESET PROG10

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

SELECT

SET

[]

TUNER PRESET PROG10

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

SELECT

SET

[]

TIMER SET / CHECK

SET UP MENU

TUNER PRESET

CLOCK SET

SELECT : [ ]

SET : [ EXECUTE ]

LANGUAGE / /

Getting Started

TUNER PRESET PROG14

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

SELECT

SET

[]

4 Press CURSOR >/. to move the cursor

(z) to CHANNEL SET.

5 Press PROG +/– to select the programme

position.

6 Press CURSOR / repeatedly until the

channel you want is displayed. Pressing

CURSOR ? goes back to the previous

channels.

The channels are scanned in the following

order:

If you know the number of the channel you want, press the

programme number buttons. For example, for channel 5, first press

“0” and then press “5.”

7 If the TV sound is distorted or noisy, press

CURSOR >/./?// to move the

cursor (z) to SYSTEM, then select either

B/G or D/K, whichever is applicable in

your area.

8 To allocate another channel to another programme position, repeat

steps 4 to 7.

9 Press EXECUTE.

TUNER PRESET PROG14

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

SELECT

SET

[]

TUNER PRESET PROG10

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

SELECT

SET

[]

Step 7 : Tuning the VCR (continued)

•CURSOR

•PROG

•CURSOR

•EXECUTE

•CURSOR

Selected programme

position

Channel coverage System D/K System B/G

VHF R1–R12 E2–E12

UHF R21–R69 E21–E69

CATV (TV distribution) — S1–S41, S01–S05

TUNER PRESET PROG14

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

SELECT

SET

[]

Getting Started

TUNER PRESET PROG14

NORMAL / CATV

AUTO PRESET

CHANNEL SET

AFT

FINE TUNING

NORM

•

CATV

OFF

SYSTEM B / G• D / K

SET : [ ]

Disabling unwanted programme positions

After tuning the TV channels, you can disable unused programme positions.

The disabled positions will be skipped later when you press the PROG +/–

buttons.

1 Press MENU, then select TUNER PRESET and press EXECUTE.

2 Select CHANNEL SET.

3 Press PROG +/– until the programme position you want to disable

appears beside “PROG” on the TV screen.

4 Press programme number button “0” twice to display the number “0”

beside CHANNEL SET.

5 Repeat steps 3 and 4 for other positions you want to disable.

6 Press EXECUTE.

If the picture is not clear

Normally, the Auto Fine Tuning (AFT) function automatically tunes in

channels clearly. If, however, the picture is not clear, you may also use the

manual tuning function.

1 Press PROG +/– to select the programme position for which you cannot

obtain a clear picture.

2 Press MENU, then select TUNER PRESET and press EXECUTE.

3 Select FINE TUNING. The fine tuning meter appears.

4 Press CURSOR ?// to get a clearer picture, then press EXECUTE.

Note that the AFT (Auto Fine Tuning) setting switches to OFF.

Note

• The menu disappears automatically if you don’t proceed for more than a few

minutes.

Selected programme

position

Basic Operations

Playing a tape

1 Turn on your TV and set it to the video channel.

2 Insert a tape.

The VCR turns on and starts playing

automatically if you insert a tape with its

safety tab removed.

DUAL MODE SHUTTLE (DMS) ring

COUNTER

RESET

p STOP

· PLAY

P PAUSE

3/#

) FF

0 REW

6 EJECT

DISPLAY

Basic Operations

3 Press · PLAY.

When the tape reaches the end, it will rewind automatically.

Additional tasks

To set the colour system

If streaks appear during playback, set COLOR SYSTEM on the VCR to

conform to the system that the tape was recorded in. (Normally set the

switch to AUTO.)

If your tape was recorded in

PAL

NTSC

MESECAM

PLAY

continued

Set COLOR SYSTEM to

PAL/MESECAM

NTSC

PAL/MESECAM

Stop play

Pause play

Resume play after pause

Search forward

Search backward

Fast-forward the tape

Rewind the tape

Eject the tape

Press

p STOP

P PAUSE

P PAUSE or · PLAY

• Turn the DUAL MODE SHUTTLE (DMS) ring to #

during playback

• ) FF or # SEARCH during playback

• Turn the DMS ring to 3 during playback

• 0 REW or 3 SEARCH during playback

• Turn the DMS ring to ) FF during stop

• ) FF during stop

• Turn the DMS ring to 0 REW during stop

• 0 REW during stop

6 EJECT

Basic Operations

Playing a tape (continued)

To play an NTSC-recorded tape

Set NTSC PB at the rear of the VCR according to the colour system of your

TV.

H M S

To use the time counter

At the point on the tape that you want to find later, press COUNTER RESET.

The counter in the display window resets to “0H00M00S.” Search for the

point afterwards by referring to the counter.

To display the counter on the TV screen, press DISPLAY.

Notes

• The counter resets to “0H00M00S” whenever a tape is reinserted.

• The counter stops counting when it comes to a portion with no recording.

• If a tape has portions recorded in both PAL and NTSC systems, the time counter

reading will not be correct. This is due to the difference between the counting cycles

of the two video systems.

• Depending on your TV, the following may occur while playing an NTSC-recorded

tape:

– the picture is black and white

– the picture shakes

– no picture appears on the TV screen

– black streaks appear horizontally on the TV screen

– the colour density increases or decreases.

Set NTSC PB to

ON PAL TV

NTSC 4.43

NTSC 3.58

If your TV is

PAL

NTSC 4.43

NTSC 3.58

Page is loading ...

Sony SLV-X815PS User manual

Brand: Sony

Model: SLV-X815PS

Category: Cassette players

Type: User manual

This manual is also suitable for

Download PDF

report

Sony SLV-X815PS User manual

This manual is also suitable for

Sony SLV-X815PS User manual

Related papers

Other documents