Triax MOD 102T User manual

Modulator MOD 102T

User Manual

Article Article no.

MOD 102T

Modulator

300127

Version A Date 02/2018 EN

Introduction

The MOD102T modulator has an HDMI input with local loop through, and a COFDM

output which is combined with the RF input. The HDMI input content can be supplied by

a number of sources, Blu-ray player, Satellite Set top box, CCTV etc. The input signal is

modulated as a COFDM output and can be distributed to a number of TV’s over an

existing private coaxial network.

It has an HDMI loop through, to connect to the local TV, and can also combine existing

RF with the modulated output channel on RF Out 1 and RF Out 2. The modulator has

adjustable level control to balance the COFDM channel with the incoming RF channels.

The source Set top box can be controlled from another TV location, via the IR remote

control over the coaxial cable, using an IR transmitter and a digital link. The coaxial

network must be connected to the RF Out 2, with the 9vdc able to pass through the

network, to remotely power the digital link.

The MOD102T Modulator can be set up, either via the front panel and LCD screen, or

through the Web user interface (RJ45 connector). Please see below for full instructions.

Equipment Detail

 MOD102T Basic Installation:

1. Connect

HDMI In (4)

and Receiver (STB)

2. Connect

HDMI Output (3)

and local TV

3. Connect

RF Out 1 (B)

and local TV

4. Connect

RF In (1)

with Terrestrial input (Aerial)

5. Plug power adapter into

DC9V/2A (8)

 Connect MOD102T with IR Transmitter and Triax Digital Link:

1. Connect the IR Transmitter to

IR sensor (2)

at the rear of the Modulator and ensure it points to

the receiver (STB)

2. Connect Triax Digital Link (not included in accessories) at the other TV location, ensure the coax

network is connected to

RF Out 2 DC9V (C)

.

 For WebUI adjustment and Upgrade

1. Connect

Ethernet (6)

and PC/Laptop via RJ45 to adjust setting and apply software upgrades.

Interface

:

1. RF In

2. IR Sensor

3. HDMI Out

4. HDMI In

5. USB

6. Ethernet

7. On/Off

8. DC 9V/2A

A. Buttons: ▲▼◄ ► Menu, OK

B. RF Out 1

C. RF Out 2 DC 9V

SET UP

Instruction o

n

how to

set up the modulator using the front panel LCD display

Press OK and to make any adjustments or changes, confirm changes by pressing OK again.

Instruction of how to use

WebUI

1.

Connecting to modulator

Step 1: Set the PC’s static IP address to 169.254.0.100

Step 2: Connect MOD102T to computer via an Ethernet cable.

Step 3: Open your browser and enter 169.254.0.3

(The Web UI only supports Windows 7 browsers or above.)

2.

Login Page:

Enter user name and password, and click login button.

Username: user

Password: 12345

<<After login, you can see main page as below>>

3.

Modulator Setting:

RF Status:

1. RF On/Off: Users can either turn the RF on or off in this this menu.

Encoder Setting:

1. Audio Type: Users can choose either AAC or MPEG.

Service Setting:

1.

Service Name: Users can edit the service name (TV Program Name).

2.

Service ID: Users are able to define a device ID from 1 to 65534.

Channel Setting:

1.

Channel: Users can select the RF output channel number from the pre-set UK channel plan.

2.

LCN: Users can define the Logical Channel Number from 1 to 1023.

Stream Setting:

1.

OrgNetwork ID: Users Users can edit OrgNetwork ID from 1 to 65534.

2.

Network ID: Users can edit Network ID from 1 to 65534.

3.

TS ID: Users can edit TS ID from 1 to 65534.

4.

Network Name: Users can define the Network name.

Parameter Setting:

1.

Constellation: The MOD102T contains the following constellation modes: QPSK, 16QAM and

64QAM.

2.

Code Rate: Refers to the FEC (Forward Error Correction) rate. Which can be set as 5/6, or 7/8

3.

Guard Interval: Users can select either 1/8, 1/16, 1/32.

4.

Transmission Mode: Transmission mode can be set as either 2K and 8K FFT

4.

Utility:

Tftp Upgrade:

Select and upload bin file & apply firmware upgrade (details below).

Change Password Setting:

Old Password: Enter old password.

New Password: Enter pew password.

Confirm Password: Enter new password again.

System Information:

This shows the Device Version and Module Version.

Other Settings:

The user can also change the language setting to English, French, German, or Danish.

Tftp Upgrade instruction

5.

Tftp Upgrade instruction

I.

Set the PC’s static IP address to 169.254.0.100

II.

Launch Tftp tool and enter the below information under DHCP server tab.

III.

Open the internet browser and enter: 169.254.0.3

Username: user

Password: 12345

User can assign any

location, but the update file

must be in the assigned

folder.

IV.

Select Utility tab and click Tftp Upgrade button

V.

The web page and Tftp will begin the upgrade process.

6.

Modulator default settings and options

Modulator Setting Description Default value Option

RF Settings

RF On/off On On/Off

Output power 65 85,78,72,65

Encoder Settings

Audio Type AAC AAC/MPEG

Service Settings

Service name CH 62 Edit Service Name

Service ID

(1~65534)

256 Enter value : 1~65534

Channel Settings

Channel CH36 CH 21 ~ 69

LCN (1~1023) 900 Enter value : 1~1023

Stream Settings

Orgnetwork ID

(1~65534)

9018 Enter value : 1~65534

Network ID

(1~65534)

8350 Enter value : 1~65534

TS ID (1~65534) 8350 Enter value : 1~65534

Network Name TRIAX Edit Network Name

Parameter Settings

Constellation 64QAM QPSK/16QAM/64QAM

Code Rate 5/6 5/6, 7/8

Guard Interval 1/8 1/8,1/16,1/32

Transmission

Mode

8K 2K, 8K

Bandwidth

8

7/8

Default Settings

Country

Factory Setting

UK

France

Denmark

Germany

Italy

RF Output

RF Enable

On

RF Power (dBuV)

65 65 65 65 65

Encoder

Audio type

AAC

Service

Service Name

CH62

CH21

CH62

Service ID

256 256 256 256 256

Channels

Set CH

CH36

CH21

CH62

Set LCN

900 39 62 No loop No loop

Private Data Specifier

Descriptor

0x0000233A

0x0000002

8

0x0000002

9

No loop

Stream

ON ID

9018 8442 8400 8468 8572

N ID

8350 8442 12801 12289 12289

TS ID

8350 301 8350 8350 8350

Network Name

TRIAX

NIT Version

1

30

1

Parameter

Constellation

64QAM

Trans. Mode

8K

Guard Interval

1/8

Code Rate

5/6

System

Info

Default

Password

Old, New, Confirm

12345 12345 12345 12345 12345

Other

Language

English

French

Danish German

The TRIAX Logo and TRIAX, TRIAX Multimedia are registered trademarks or

trademarks

of the TRIAX Company or its affiliates.

All specifications in this guide are subject to change without further notice.

Triax MOD 102T User manual

Triax MOD 102T User manual

Related papers

Other documents