Simpson Strong-Wall Site-Built Portal Frame System Hardware Installation guide

Simpson
Brand
Simpson
Model
Strong-Wall Site-Built Portal Frame System Hardware
Category
Wall & ceiling mounts accessories
Type
Installation guide
Single-Wall Portal Frame Kit
(2) Holdown assemblies
(2) Orange composite standoff bases*
(5) Moment connection straps
(1) Adjustable post base (ABW44Z)
(33) SDW22300 truss-ply screws
(8) SD9112 Connector screws
(1) 6-lobe T40 driver bit
(1) Installation instructions
Double-Wall Portal Frame Kit
(4) Holdown assemblies
(4) Orange composite standoff bases*
(8) Moment connection straps
(66) SDW22300 truss-ply screws
(1) 6-lobe T40 driver bit
(1) Installation instructions
Single-Wall Portal Cut Lengths
Tall column (C1) = H1 + BD – 35 mm
Short column (C2) = H1 – 35 mm
Long beam (B1) = W1 + CW + PW
Short beam (B2) = W1 + PW
Double-Wall Portal Cut Lengths
Tall column (C1) = H1 + BD – 35 mm
Short column (C2) = H1 – 35 mm
Long beam (B1) = W1 + CW + CW
Short beam (B2) = W1
Single-Wall Portal Double-Wall Portal
Single-Wall Portal Installation Double-Wall Portal Installation
®
THIS SI DE U P
THIS SI DE U P
PFS-SB12
PATENT PENDING
SIMPSON
Strong-Tie
®
C1
B2
B1
C2
®
THIS SI DE U P
THIS SI DE U P
PFS-SB12
PATENT PENDING
SIMPSON
Strong-Tie
®
®
THIS SIDE UP
THIS SIDE UP
PFS-SB12
PATENT PENDING
SIMPSON
Strong-Tie
®
B2
B1
C1
C2
CW
H1
35 mm
W1
PW
BD
CW
BD
H1
W1
CW
35 mm
Note: Reference building plan for PFS
model and framing material type.
Legend:
BD = Beam Depth
CW = Column Width
PW = Post Width
H1 = Opening Height
W1 = Opening Width
*Extra composite standoff bases
included. Only use the
base that corresponds to
the column width and discard
extra base(s).
TECHNICAL BULLETIN
Strong-Wall
®
Site-Built Portal Frame System
Hardware Installation Instructions
© 2020 Simpson Strong-Tie Company Inc. T-L-PFSHWAU20
1300 STRONGTIE
(1300 787664)
strongtie.com.au
This technical bulletin is effective until June 30, 2022, and reflects information available as of January 1, 2020.
This information is updated periodically and should not be relied upon after June 30, 2022.
Contact Simpson Strong-Tie for current information and limited warranty or see strongtie.com.
© 2020 Simpson Strong-Tie Company Inc. •
Unit 1 /16 Kenoma Place Arndell Park NSW. 2148 Australia
T-L-PFSHWAU20 1/20
C1
C2
18"
9" typ.
1½
"
typ.
BD
Thickness (T)*
C1
C2
18"
1½
"
typ.
9
"
typ.
BD
Thickness (T)*
C1
C2
18"
14"
C
L
9
"
typ.
1½
"
typ.
Allowable
hole zone
(20mm dia. max)
BD
3
"
Holdown Installation
1. Install holdown assembly on anchor bolts as shown.
2. Tighten nuts on anchor bolts.
Note: Tighten nuts only after adhesive has cured.
1. Connect the beam sub-assembly to the column sub-assembly starting with the SDW screws
(provided), as shown.
2. Install the PFS-MCS straps using 3.75mm-diameter nails (64mm minimum length). The straps
must be installed horizontally on the tall column (C1) side and vertically on the short column (C2)
side, as shown.
Note: Strong-Drive
®
SD10212 Connector screws (not provided) may be substituted for the nails.
Note: If using nails, every other row is installed on opposite side.
*Note: Required Fasteners:
SDW22300 SDW Truss-Ply Screw (installation only required from one side)
or use 75mm x 3.75mm nails.
*Note: Required Fasteners:
SDW22300 SDW Truss-Ply Screw (installation only required from one side)
or use 75mm x 3.75mm nails.
¼" typ.
¼" typ.
Short column
Column-to-Beam — Moment Connection Details
Front Front Back
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
1½"
1½"
1½"
1½"
1
½"
1½"
C
L
C
L
Tall column
Single-Wall Portal —
Post-to-Beam Detail
(strap only required on
one side)
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
3.00
WS22
¼" typ.
¼
" typ.
¼
" typ.
Column-to-Beam Moment Connection Installation
Note: Refer to T-L-PFSANAU20 for
anchorage installation instructions
and details. Reference building plans
for anchorage and embedment depth.
Additional anchorage information can
be found at strongtie.com/au.
Double-Wall Beam Assembly
Single-Wall Beam Assembly
PFS9 Column Assembly PFS12 Column Assembly Allowable Hole Zone
CW
B2
B1
Thickness (T)*
100mm typ.
40mm typ.
300mm
typ.
B2
B1
100mm typ.
CW
Thickness (T)*
CW
40mm typ.
300mm
typ.
40mm
typ.
225mm typ.
450mm
450mm
450mm
350mm
40mm 40mm
40mm
40mm
40mm
225mm typ.
225mm typ.
40mm
typ.
40mm
typ.
6mm
6mm
6mm
6mm
6mm
40mm
TECHNICAL BULLETIN
Strong-Wall
®
Site-Built Portal Frame System
Hardware Installation Instructions
  • Page 1 1
  • Page 2 2

Simpson Strong-Wall Site-Built Portal Frame System Hardware Installation guide

Simpson
Brand
Simpson
Model
Strong-Wall Site-Built Portal Frame System Hardware
Category
Wall & ceiling mounts accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents