Frontier 85
User Guide
IMPORTANT: Thoroughly read, understand, and follow all instructions
before installing this child seat. Store this user guide in the pocket behind
the cover (See features pages for reference).
©2009 Britax Child Safety, Inc. All rights reserved. Printed in USA P392700_R1:12.09
This product and its components are subject to change without notice.
Warnings ......................................................................................................2
Safety Information .......................................................................................4
Important Notes ....................................................................................................4
Certification ...........................................................................................................4
Registration ...........................................................................................................5
Child Seat Features .....................................................................................6
Child Seat Fit Requirements ......................................................................8
Vehicle Compatibility ..................................................................................10
Compatible Vehicle Seat Belts ............................................................................10
Incompatible Vehicle Seat Belts ..........................................................................14
Child Seat Functions ...................................................................................16
Installing the Child Seat ..............................................................................26
General Information .............................................................................................26
Harness Mode .................................................................................................26
Booster Mode ..................................................................................................27
Installing the Child Seat: Harness Mode ..................................................28
Lower Anchors and Tethers for Children (LATCH) – Short Path .......................28
Lap-Shoulder Belt – Selecting a Belt Path ..........................................................32
Lap-Shoulder Belt – Short Path ...........................................................................34
Lap-Shoulder Belt – Long Path ...........................................................................38
Lap Belt – Short Path............................................................................................42
Switching Between Modes .........................................................................46
Harness to Booster Mode ....................................................................................46
Booster to Harness Mode ....................................................................................48
Positioning the Child Seat: Booster Mode ...............................................52
Using LATCH ........................................................................................................53
Lap-Shoulder Belt.................................................................................................54
Securing Your Child ....................................................................................55
Harness Mode ......................................................................................................55
Booster Mode .......................................................................................................58
Care and Maintenance ................................................................................60
Tips and Troubleshooting ...........................................................................69
Warranty .......................................................................................................72
Table of Contents
2
3
Section Title
Section Title
Harness mode: use only with children who weigh between 25 •
and 85 lbs (11.4 and 38.6 kg) and whose height is between 30
and 57 in. (76.2 and 144.8 cm) and are at least 2 years of age.
Booster mode: use only with children who weigh between 40 •
and 120 lbs (18.2 and 54.5 kg) and whose height is between
42 and 65 in. (106.7 and 165.1 cm).
Snugly adjust the belts provided with this child restraint around •
your child.
Secure the top anchorage strap provided with this child seat.•
Use only the vehicle’s lap and shoulder belt system when •
restraining the child in this booster seat.
Secure this child restraint with the vehicle’s child restraint •
anchorage system if available or with a vehicle belt.
Follow all instructions on this child restraint and in the written •
instructions located in the pocket behind the cover of the child
seat.
Register your child restraint with the manufacturer.•
For harness mode refer to your vehicle owner’s manual or •
contact the vehicle manufacturer for the maximum weight
rating for the LATCH anchors in your vehicle. Use the vehicle
belt (not LATCH connectors) for installations with children
who weigh more than the vehicle LATCH anchor limit. Unless
specified otherwise by the vehicle manufacturer, assume a 40
pound (18.2 kg) child is the vehicle LATCH anchor limit.
Use this child seat forward-facing only.•
According to accident statistics, children are safer when •
properly restrained in the rear seating positions than in the front
seating positions.
This child seat must not be used in the home, in boats, or other •
non-certified applications.
To prevent injury due to deterioration or hidden damage, •
discontinue use of this child seat when it is older than nine
years or has been in a moderate or severe crash. See date of
manufacture and expiration date located on child seat shell.
See page 6.
The primary protection for occupants of a vehicle in a collision •
is the body of the vehicle itself. A child seat may not protect a
child when the vehicle is seriously im pact ed. However when
correctly installed, a child seat will substantially improve the
chances for survival in most crashes.
Cover the child seat when the vehicle is parked in direct •
sunlight. Parts of the child seat can become hot enough to
burn a child.
Secure this child seat even when it is not occupied. In a crash, •
an unsecured child seat may injure vehicle occupants.
Store the child seat in a safe place when it is not being used. •
Avoid placing heavy objects on top of the child seat.
Never use the harness or adjuster strap to lift or carry this child •
seat. Doing so could damage the harness adjuster and webbing.
Always carry this child seat by the shell or tether straps.
Do not allow children to play with this child seat.•
The use of non-Britax covers, inserts, toys, accessories, or •
tightening devices is not approved by Britax. Their use could
cause this child seat to fail Federal Motor Vehicle Safety
Standards or not perform as intended in a crash.
Always check the back seat upon leaving your vehicle to prevent •
leaving a child restrained in a child seat alone in the vehicle.
Do not leave loose objects, e.g. books, bags, etc., in the back •
of a vehicle. In the event of a sudden stop, loose objects will
keep moving, potentially striking passengers and causing
serious injuries.
Do not leave folding vehicle seats unsecured. In the event of a •
sudden stop, a loose seat back could cause the child seat not
to perform as intended.
WARNING!
DEATH or SERIOUS INJURY can occur:
4
5
Important Notes
Verify that the child seat is securely installed and that the •
harness is properly adjusted around the child each time the
child seat is used.
Adjust the harness to fit the clothes the child is wearing. •
Remove bulky coats and/or jackets before putting the child in
the child seat.
Do not, except as described in this booklet, attempt to •
disassemble any part of the child seat or change the way the
harness or vehicle’s seat belts are used.
Do not use anything to raise the child seat off of the vehicle seat. •
In a crash, this could cause the child seat not to perform as
intended.
Certification
This child seat system conforms to all applicable
Federal Motor Vehicle Safety Standards.
This Restraint is Certified for Use in Motor Vehicles
and Aircraft when Used in Harness Mode.
This Restraint is Not Certified for Use in Aircraft when
Used in Booster Mode.
Belt positioning booster seats
require lap-shoulder belt installation not
available in aircraft.
Follow lap-belt installation instructions found
on page 42, to install this child seat in aircraft.
NOTE: The Versa-Tether cannot be used in aircraft.
Install your child seat in a window seat to avoid
blocking the aisle.
If the aircraft lap belt is too short, ask the flight attendant for a belt
extender.
Registration
Child seats can be recalled for safety reasons. You must register
this child seat to be reached in a recall. Send your name, address,
and the child seat’s model number and manufacturing date to
Britax Child Safety, Inc., 13501 South Ridge Drive, Charlotte,
NC 28273, or call 1-888-4BRITAX, or register online at www.
BritaxUSA.com/registration. For recall information, call the U.S.
Government’s Vehicle Safety Hotline at 1-888-327-4236 (TTY
1-800-424-9153), or go to http://www.NHTSA.gov.
Serial Number:___________________________________
Batch Number:___________________________________
Date of Manufacture:______________________________
Safety InformationSafety Information
6
7
Cover1
Manufactured Date and 2
Expiration Date Label
LATCH Strap3
Arm Rest4
Cup Holder5
Head Restraint6
Head Restraint Cover7
Harness Slot8
9
User Guide Storage (in
pocket behind cover)
Shoulder Belt Guide10
Comfort Pads11
HUGS™ Chest Pads12
Chest Clip13
Harness Straps14
Harness Buckle15
Lower Belt Guide16
Belly Pad17
Harness Adjuster Release 18
Lever (under flap)
Harness Adjuster Strap19
Head Restraint Adjuster 20
Locking Screw Storage Slot
LATCH Connector21
LATCH Connector Storage Slot22
LATCH Connector Release 23
Button
LATCH Adjuster24
LATCH Adjuster Release 25
Button
Belt Slot26
Harness Yoke Storage (on belt 27
shield)
Versa-Tether28
®
Hook
Versa-Tether29
®
Storage Clip
Locking Screw30
Head Restraint Adjuster31
Shell32
Versa-Tether (Top Anchorage 33
Strap)
Versa-Tether34
®
Adjuster
Versa-Tether35
®
Webbing
Storage Strap
Harness Height Adjuster36
Belt Shield37
Harness Yoke (behind Belt 38
Shield)
Positioning Block39
6
7
8
10
15
16
18
17
19
30
31
32
33
34
35
36
37
39
38
4
3
2
1
28
27
29
25
26
24
23
22
20
21
5
9
11
12
14
13
Child Seat FeaturesChild Seat Features
8
9
Harness Mode:
Children must:
be at least two years of age 1 and
weigh between 25 – 85 lbs (11.4 – 38.6 kg) 2 and
stand 30 – 57 in. (76.2 – 144.8 cm) in height 3 and
WARNING! Harness mode use of this child seat is ONLY
for children who meet ALL of the following requirements. If the
child does not meet all harness mode requirements because
the child is too small, another type of child seat MUST be used.
If your child does not meet all harness mode requirements
because they are too large, you may need to use this child
seat in booster mode. Thoroughly review all fit requirements
before using the child seat.
WARNING! Booster mode use of this child seat is ONLY for
children who meet ALL of the following requirements. Use only the
vehicle’s lap and shoulder belt to secure the child. If the child does not
meet all booster mode requirements because the child is too small,
you may need to use this child seat in harness mode. Thoroughly
review all fit requirements before using the child seat.
Children must:
be at least 40 – 120 lbs (18.2 – 54.5 kg) 1 and
stand 42 – 65 in. (106.7 – 165.1 cm) in height 2 and
the top of the child’s ears must be below the top of the head 3
restraint and
the vehicle belt must be appropriately positioned at or above 4
the child’s shoulder through the shoulder belt guide.
Shoulder level
Above Shoulder Level
Below Shoulder Level
NOTE: Britax recommends booster mode only after the child
outgrows harness mode.
the top of the child’s 4
ears must be below the
top of the head restraint
when seated and
the harness straps must 5
be located at or above
the child’s shoulders
when seated.
Booster Mode:
Child Seat Fit RequirementsChild Seat Fit Requirements
10
11
Switchable Retractor in ALR Mode with Sliding Latch Plate3.
Has a latch plate that freely
a
slides along the vehicle belt
webbing.
Has a retractor that can be
b
switched to function as an
ALR by pulling the vehicle
belt fully out until a clicking
sound can be heard when
retracting.
To use a child seat with this *
type of vehicle belt, you will
need to switch to the ALR
mode or use a locking clip.
Compatible Vehicle Seat Belts
NOTE: The information in this section only applies to installation
with vehicle belts.
Vehicle seats and seat belts differ from vehicle to vehicle. Refer to
your vehicle owner’s manual for specific information about your
vehicle belts and their use with child seats.
Lap-Shoulder (3-Point) Belt
ALR (Automatic Locking Retractor) with Sliding Latch Plate 1.
Has a latch plate that freely
a
slides along the vehicle belt
webbing.
Has a retractor that stops the
b
belt from being pulled out
again once the belt webbing
has been pulled out at least
24 in. (61 cm).
Tightens by feeding the
c
belt webbing back into the
retractor.
ELR (Emergency Locking Retractor) with Locking Latch Plate2.
Has a latch plate that does
a
not allow the lap part of the
belt to become loose after it
is buckled.
Has a retractor that locks
b
only in an emergency
situation such as sudden
stop or crash.
Latch
Plate
Latch
Plate
Latch
Plate
Vehicle CompatibilityVehicle Compatibility
12
13
Locking Latch Plate6.
Has a latch plate that
a
does not allow the belt to
become loose after it is
buckled.
Tightens by pulling on the
b
belt webbing.
ELR (Emergency Locking Retractor) with a Sliding Latch Plate4.
Has a latch plate that freely
a
slides along the vehicle belt
webbing.
Has a retractor that locks
b
only in an emergency
situation such as sudden
stop or crash.
IMPORTANT: This belt type requires
the use of a locking clip to secure
the seat during installation. A locking
clip must be secured approximately
1 in. (2.5 cm) from the latch plate to
secure the child seat.
Call Britax Consumer Services at
1(888) 427-4829 to obtain a locking
clip.
Has a retractor that stops the b
belt from being pulled out
again once the belt webbing
has been pulled out at least
24 in. (61 cm).
Tightens by feeding the
c
belt webbing back into the
retractor.
Latch
Plate
Adjuster
Latch
Plate
Lap Belt
IMPORTANT: A Lap belt may only be used to install the child seat
in harness mode and should never be used to secure your child in
booster mode.
ALR (Automatic Locking 5.
Retractor)
Has a latch plate that is a
sewn into the webbing.
1” (2.5 cm)
from Latch
Plate
Vehicle CompatibilityVehicle Compatibility
14
15
Vehicle Buckle Positions
WARNING! The following types of vehicle belts are NOT
compatible with this child seat:
Incompatible Vehicle Seat Belts
Lap-shoulder belts with 1
top or bottom anchor
points on the vehicle door.
Motorized, automatic vehicle 2
belts.
Lap-shoulder belts that have 3
a separate retractor each
for the lap part and shoulder
part.
Lap belts forward of the 4
vehicle seat bight.
Lap belts that have a retractor that locks only 5
in case of a sudden stop (emergency locking
retractor or ELR).
WARNING! Some vehicles have no seating positions which
are compatible with this child seat or any other child seat. If in
doubt, contact the vehicle manufacturer for assistance.
Forward-facing vehicle seats MUST be used with this child
seat. Side-facing or rear-facing seats CANNOT be used. See
diagram below.
Vehicle Seating Positions
DO NOT place a child seat
in the front seat of a
vehicle with a passenger
air bag unless
deactivated. DEATH or
SERIOUS INJURY can
occur. See your vehicle
owner's manual for child
seat installation
instructions. The back
seat is the safest place for
children 12 and under.
WARNING!
WARNING! The position of the vehicle
belt buckle can adversely affect the stability
of the child seat.
If the buckle lies near the incorrect position ( ) when
the vehicle belt is tightened, try fitting the child seat
in another seating position in the vehicle OR consult
your vehicle owner’s manual to see if you can lower
the vehicle buckle position by twisting the vehicle
buckle stalk. If it is not possible to achieve the correct
position (
) for the buckle, then another seating
position MUST be used.
Vehicle CompatibilityVehicle Compatibility
16
17
Harness Mode: Harness Height Adjustment
IMPORTANT: Make all adjustments for the fit of your child before
using the child seat. Place the child seat on the floor and have your
child sit in the seat. Follow the instructions on the following pages
to make the proper adjustments to the harness, buckle, and head
restraint.
WARNING! Head restraint adjustment is for use in Booster
Mode ONLY. DO NOT Use the head restraint adjuster when the
harness is attached.
Lift the head restraint 2
adjuster release to move
the head restraint.
Loosen the harness. 1
Press release levera
Pull both harness straps b
forward
Lift and slide the harness 2
height adjuster into the
desired position, then
release.
Ensure the adjuster is *
seated securely between
the notches.
Booster Mode: Head Restraint Adjustment
Remove the locking screw
1
from the head restraint
adjuster and insert into the
shell to store for later use.
IMPORTANT: The vehicle belt must be positioned at or above the
child’s shoulder through the shoulder belt guide.
IMPORTANT: In harness mode,
the harness height adjuster also
adjusts the height for the head
restraint. Always position the
harness straps at or above your
child’s shoulders.
Locking Screw
storage
Shoulder level
Above Shoulder Level
Below Shoulder Level
Child Seat FunctionsChild Seat Functions
18
19
Adjusting Buckle Position
Removing the Buckle
Unbuckle the harness by
1
pressing the release button
and pulling the tongues.
Re-threading the Buckle
IMPORTANT: Select the slot
closest to, but not under the child.
Turn and push the buckle 1
retainer through the slot in the
cover and child seat shell.
Locate the buckle retainer on
2
the bottom of the child seat.
Slide the buckle retainer up
3
or down to release it from the
child seat shell.
Pull the buckle retainer away
4
from the child seat to loosen.
Turn and push the buckle
5
retainer through the slot in the
child seat shell.
Pull the buckle retainer 2
through the slots in the cover
and child seat shell to the
bottom of the child seat.
Pull the buckle away from the
4
child seat until tight.
Ensure that the buckle strap is *
not twisted.
2
Pull the buckle retainer 6
through the slots in the child
seat shell and cover to the top
of the child seat.
Slide the buckle retainer back
3
into place to hold it against
the child seat shell.
Child Seat FunctionsChild Seat Functions
20
21
Insert one tongue at a time into
the buckle.
NOTE: Proper connection is
confirmed with an audible click
after inserting each buckle
tongue.
Fastening the Buckle Releasing the Buckle
Press the release button and
pull the tongues from the
buckle.
NOTE: Periodically clean
the buckle to ensure proper
operation. See Page 67.
Using the Chest Clip
Squeeze to
1
open
Push together to fasten
2
NOTE: Always position the chest clip at
armpit level.
Using the Positioning Block
NOTE: Set the positioning block position BEFORE installing.
Unhook the Versa-Tether from
1
the storage clip
Harness Position2
Booster Position3
Positioning
Block
Positioning
Block
Child Seat FunctionsChild Seat Functions
22
23
Using the LATCH Connectors
The LATCH connectors are located on the sides of the shell in the
storage slots. Store the LATCH connectors when not in use.
To remove the LATCH connector from the storage slot or lower
anchor:
Press and hold the red release
1
button.
Pull the LATCH connector
2
from the storage slot or lower
anchor.
To attach the LATCH connector to the storage slot or lower
anchor:
Firmly push the LATCH connector
into the slot or lower anchor until a
click is heard to store.
NOTE: The LATCH connectors
store in the slots upside-down.
Using Lower Anchors and Tethers for Children (LATCH)
LATCH SYSTEM ANCHOR LOCATIONS
T e ther
Anchor
Lower LATCH
Anchors
The figure above shows typical locations for lower anchors and
tether anchors in a vehicle. Check your vehicle owner’s manual
for the exact LATCH anchor locations and seating positions
(if equipped), information on use with a child seat, and for the
maximum weight rating for the LATCH anchors.
Standard vehicle seat spacing between LATCH anchors is 11 inches
(27.9 cm). This child seat can be used in a seating position with up
to 20 inches (50.8 cm) of space between the LATCH anchors if the
vehicle manufacturer allows.
Top
Child Seat FunctionsChild Seat Functions
24
25
To remove the Versa-Tether from the storage clip:
Remove the webbing from the
1
elastic strap and loosen the
Versa-Tether.
Remove the Versa-Tether
2
®
hook from the storage clip.
To attach the Versa-Tether to the storage clip or a tether
anchor:
Firmly press the hook over the
1
storage clip or tether anchor
point.
Always attach the hook over 2
the anchor point.
IMPORTANT: Use the elastic strap
to contain extra webbing. Always
ensure any excess webbing is
contained within your vehicle.
Using the Versa-Tether
WARNING!
Attach the Versa-Tether only to tether anchors identified by •
your vehicle manufacturer as tether anchorage points.
If your vehicle does not currently have a tether anchor •
attachment, refer to your vehicle owner’s manual or
contact your vehicle man u fac tur er for assistance. DO
NOT modify your vehicle without advice from your vehicle
manufacturer.
When using the child seat in harness mode:
Britax recommends that the tether be used at all times •
when installing the child seat. Using the tether will improve
the stability of your child seat and reduce the risk of injury.
You must • always use the Versa-Tether for children
weighing 65 – 85 lbs (29.5 – 38.6 kg).
Tether anchor locations vary
from vehicle to vehicle. Check
your vehicle owner’s manual
and look for the tether anchor
symbol shown in the diagram
to help identify where the top
tether anchor point is located
in your vehicle.
OR
OR
OR
OR
Child Seat FunctionsChild Seat Functions
26
27
WARNING!
Long belt path is only for use with a lap-shoulder belt. Never •
use the long belt path option with LATCH or a lap belt.
Use• only the vehicle’s lap and shoulder belt system when
restraining a child in booster mode. Never restrain a child with
only a lap belt in booster mode.
You MUST always• use the Versa-Tether for children weighing 65
– 85 lbs (29.5 – 38.6 kg) in harness mode.
Install forward-facing only.•
DO NOT use anything to raise the child seat off of the vehicle seat.•
Refer to your vehicle owner’s manual or contact the vehicle •
manufacturer for the maximum weight rating for the LATCH
anchors in your vehicle. Use the vehicle belt (not LATCH
connectors) for installations with children who weigh more than
the vehicle LATCH anchor limit. Unless specified otherwise by
the vehicle manufacturer, assume a 40 lb (18.2 kg) child is the
vehicle LATCH anchor limit.
General Information
Harness Mode
The positioning block must be •
rotated to the front when installing
the child seat in harness mode.
Based on your vehicle’s seat belt •
configuration, you may achieve
a more secure installation using
one of two approved lap-
shoulder belt path options (long
or short belt path). If the first
installation method results in more than 1 in. (2.5 cm) of front-to-
back or side-to-side movement at the belt path, try the other option.
See page 32 for information on selecting a belt path to install this
child seat in your vehicle.
Use this child seat in harness mode with children at least 2 years of •
age and 25 – 85 lbs (11.4 – 38.6 kg) who stand 30 – 57 in. (76.2 –
144.8 cm) in height. Britax recommends using harness mode to 85
lbs (38.6 kg). See the Child Seat Fit Recommendations section on
page 8 for information on when your child has outgrown harness mode.
Booster Mode
The positioning block must •
be rotated to the back when
positioning the child seat in
booster mode.
This child seat can be used in •
booster mode with children who
stand 42 – 65 in. (106.7 – 165.1
cm) in height and weigh more
than 40 lbs (18.2 kg). Britax
recommends using harness
mode to 85 lbs (38.6 kg).
When positioning this child •
seat in booster mode use the
vehicle’s lap-shoulder belt to
secure the child and child seat
into the desired seating position.
In booster mode, this child •
seat can be positioned on the
vehicle seat using LATCH. Use
the vehicle’s lap-shoulder belt
to secure the child. Ensure that the LATCH system does not interfere
with the vehicle belt function and alignment when securing your child.
Positioning
Block
Positioning
Block
Installing the Child SeatInstalling the Child Seat
28
29
LATCH – Short Path
Before you begin:
Check that your vehicle has LATCH anchors. 9
Check your vehicle owner’s manual for the vehicle’s LATCH *
anchor limits.
Check that your vehicle has a top tether anchor. 9
You MUST always* use the Versa-Tether for children weighing
65 – 85 lbs (29.5 – 38.6 kg).
Britax recommends that the Versa-Tether is used at all times. *
Using the tether will improve the stability of the child seat and
reduce the risk of injury. Check your vehicle owner’s manual for
tether anchor locations.
Remove the Versa-Tether 9
®
hook from the storage clip and
place it over the child seat back to keep it from becoming
pinned between the child seat and vehicle seat during
installation.
Versa-Te ther
(Top Te ther)
Install with LATCH using only the short belt path as shown
above.
Installing the Child Seat: Harness ModeInstalling the Child Seat: Harness Mode
30
31
Locate the LATCH anchors in 1
your vehicle.
Ensure harness height is *
adjusted to fit your child.
Rotate the positioning block to 2
the front and place the child
seat on the vehicle seat.
Verify that the LATCH strap is
3
not twisted and firmly press
the LATCH connectors onto
their adjacent LATCH anchors
to attach.
Push the child seat into the
4
vehicle seat and pull the end
of the LATCH strap through
the belt slot to secure.
The child seat is secure when it *
cannot be moved front-to-back
or side-to-side more than 1 in.
(2.5 cm) at the belt path. If the
child seat is not secure, repeat
the installation procedure or
use a different seating location.
Firmly press the Versa-Tether5
®
hook to the vehicle tether
anchor to attach. Remove all
slack from the tether webbing.
Use the elastic strap to contain
6
extra webbing.
1
2
OR
OR
Checklist
Check that positioning block is rotated to the front. 9
Check all connections and verify that child seat is secure. 9
The child seat is secure when it cannot be moved front-to-*
back or side-to-side more than 1 in. (2.5 cm) at the belt path.
If the child seat is not secure, repeat the installation procedure
or use a different seating location.
Ensure any excess Versa-Tether 9
®
webbing is stored in elastic
band. Always ensure any excess webbing is contained within
your vehicle.
<1 in.
Check Versa-T e ther
®
(Top T e ther) attachment
Check that Versa-T e ther
®
(Top T e ther) webbing is
stored in elastic band
Check LATCH
connector attachments
Check that the
Positioning Block is
rotated to the front
Check that there is
LESS than 1 in. (2.5 cm)
of movement (front to back
or side to side) at the belt path
Installing the Child Seat: Harness ModeInstalling the Child Seat: Harness Mode
32
33
Lap-Shoulder Belt – Selecting a Belt Path
Due to variability in vehicle seat designs and belt systems, the
Frontier 85 child seat can be secured to the vehicle seat by a
lap-shoulder belt with either a short belt path or a long belt path
installation method.
The following may help with selecting which belt path to try first:
WARNING! Do not use the long belt path for LATCH or lap
belt installations.
Outside edge
of child seat
Buckle stalk behind
child seat
The buckle stalk is in position for
short belt path installation
Outside edge
of child seat
Buckle stalk beside
child seat
The buckle stalk is in position for
long belt path installation
If the buckle stalk is to the side of the child seat (i.e. the child seat B
is narrower than the insertion points of the vehicle belt system),
then the long belt path may be the best option to try first.
If one installation method results in more than 1 in. (2.5 cm) of
front-to-back or side-to-side movement at the belt path, then try the
other method.
Both the short and long lap-shoulder belt path installation methods
meet or exceed all Federal motor vehicle Safety Standards. Either
of these options can be used based upon vehicle compatibility for
children at least 2 years old and 25 lbs (11.4 kg) up to 85 lbs (38.6
kg) in harness mode.
Rotate the positioning block to the front and place the child
A
seat on the vehicle seat in the chosen seating position. Note the
position of the vehicle buckle stalk relative to the child seat. If the
buckle stalk is behind the child seat (i.e. the child seat is wider
than the insertion points of the vehicle belt system), then the short
belt path may be the best option to try first.
Installing the Child Seat: Harness ModeInstalling the Child Seat: Harness Mode
34
35
Before you begin:
Check that your vehicle has a seat belt that can be locked. 9
Check your vehicle owner’s manual to determine what type *
of vehicle belt you have and how it can be locked for use with
child seats. If your vehicle belt does not lock, a locking clip must
be used. Call Britax Consumer Services at 1(888)427-4829 to
obtain a locking clip.
Check that your vehicle has a top tether anchor? 9
You MUST always* use the Versa-Tether for children weighing
65 – 85 lbs (29.5 – 38.6 kg).
Britax recommends that the Versa-Tether is used at all times. *
Using the tether will improve the stability of the child seat and
reduce the risk of injury. Check your vehicle owner’s manual for
tether anchor locations.
Remove the Versa-Tether 9
®
hook from the storage clip and
place it over the child seat back to keep it from becoming
pinned between the child seat and vehicle seat during
installation.
Versa-Te ther
®
(Top Te ther)
Lap-Shoulder Belt – Short Path
Short lap-shoulder belt path installation
Installing the Child Seat: Harness ModeInstalling the Child Seat: Harness Mode
36
37
Rotate the positioning block to 1
the front and place the child
seat on the vehicle seat.
Ensure harness height is *
adjusted to fit your child.
Pull the vehicle belt out and 2
route the belt through the first
belt slot, under the cover and
through the second belt slot.
Verify that the belt is not
3
twisted and then buckle.
Push the child seat firmly
4
into the vehicle seat while
removing all slack from the lap
part (a), then shoulder part (b)
of the vehicle belt.
Ensure that the vehicle belt *
is locked as directed by your
vehicle owner’s manual.
The child seat is secure when it *
cannot be moved front-to-back
or side-to-side more than 1 in.
(2.5 cm) at the belt path. If the
child seat is not secure, repeat
the installation procedure or
use a different seating location.
Firmly press the Versa-Tether5
®
hook to the vehicle tether
anchor to attach. Remove all
slack from the tether webbing.
Use the elastic strap to contain
6
extra webbing.
OR
OR
Checklist
Check that positioning block is rotated to the front. 9
Check all connections and verify that child seat is secure. 9
The child seat is secure when it cannot be moved front-to-*
back or side-to-side more than 1 in. (2.5 cm) at the belt path.
If the child seat is not secure, repeat the installation procedure
or use a different seating location.
Ensure any excess Versa-Tether 9
®
webbing is stored in elastic
band. Always ensure any excess webbing is contained within
your vehicle.
Check Versa-T e ther
®
(Top T e ther) attachment
Check vehicle
buckle attachment
<1 in.
Check that Versa-T e ther
®
(Top T e ther) webbing is
stored in elastic band
Check that the
Positioning Block is
rotated to the front
Check that there is
LESS than 1 in. (2.5 cm)
of movement (front to back
or side to side) at the belt path
Installing the Child Seat: Harness ModeInstalling the Child Seat: Harness Mode
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Britax 85 SICT User manual
-
Britax FRONTIER 85 User manual
-
-
-
-
-
-
-
Britax ADVOCATE User manual
-
Other documents
-
Kmart 43171781 User manual
-
Columbia Spirit APS 2400 Instructions Manual
-
-
Cosco FINALE DX Instructions Manual
-
-
Husky Baby Carrier User manual
-
Inspired by drive CSI-2000 User manual
-
-
R82 Quokka User guide
-
Baby Jogger City Single User manual
