Fantom CW233H User manual

Brand: Fantom

Model: CW233H

Category: Vacuum cleaners

Type: User manual

Commercial Stainless Steel Wet/Dry Vacuum

FANTOM

94 Main Mill Street, Door 16

Plattsburgh, NY 12901

Tel. :1 (800) 275-9251

OWNER’S MANUAL

Model CW233H

120V., 60Hz., 8.3 Amps

FOR HOUSEHOLD OR COMMERCIAL USE

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock, or injury:

• Do not leave the vacuum plugged in when

unattended. Unplug the electrical cord when not

in use and before servicing.

• Do not allow to be used as a toy. Close attention is

necessary when used by or near children, pets or

plants.

• Use only as described in this manual. Use only

manufacturer’s recommended accessories.

• Do not pull cord, use cord as a handle, close a

door on cord, or pull cord around sharp edges

or corners.

• Do not run unit over power cord. Keep cord away

from heated surfaces.

•Use only extension cords UL-rated or cUL at 15

amperes. Extension cords rated for less amperage

may overheat. Care should be taken to arrange the

cord so that the cord cannot be pulled or tripped over.

• Turn off unit before unplugging from electrical outlet.

• Do not handle plug or vacuum with wet hands or

operate without shoes.

• Do not put any objects into openings. Do not use

with any opening blocked. Keep free of dust, lint, hair

and anything else that may reduce air flow.

• Store your appliance indoors in a cool, dry area.

• Keep your work area well lit.

• Do not immerse the vacuum into water or other

liquids.

• Keep end of hose, wands and other openings away

from your face and body.

• Using improper voltage may result in damage to the

motor and possible injury to the user. Correct voltage

is listed on rating label.

When using your Wet/Dry Vacuum, basic safety precautions should always be observed, including the following:

1. Read all instructions before using your vacuum.

2. Use the vacuum only for its intended use.

3. To protect against a risk of electric shock, do not

immerse any part of the vacuum in water or other

liquids.

4. Never yank cord to disconnect from outlet; instead,

grasp plug and pull to disconnect.

5. Do not allow cord to touch hot surfaces.

6. Do not run appliance over cord.

7. Do not operate the vacuum with a damaged cord or

plug, or if the appliance or any other part of the

vacuum has been dropped or damaged. To avoid

the risk of electric shock, do not disassemble or

attempt to repair the vacuum. Return the vacuum to

FANTOM (see warranty) for examination and

repair. Incorrect re-assembly or repair can cause a

risk of electrical shock or injury to persons when

the vacuum is used.

8. Close supervision is necessary for any appliance

being used by or near children. Do not leave the

vacuum unattended while connected.

9. Keep hair, loose clothing, fingers and all parts of

body away from any opening and moving parts.

10. Do not use to pick up flammable or combustible

liquids such as gasoline or use in areas where

they may be present.

11. Do not pick up anything that is burning or smoking

such as cigarettes, matches or hot ashes.

12. Use extra care when cleaning on stairs.

13. This unit should not be used to pick up liquids from

containers, sinks, tubs, etc.

14. Do not use on uneven surfaces. Do not tip/tilt unit

over when in use.

15. Intended for indoor or outdoor use and for wet pick-

up, but not intended to be exposed to rain.

Rev. 07/06

WARNING: The power cord on this product contains lead, a chemical known to the State of

California to cause birth defects or other reproductive harm. Wash hands after handling.

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path

of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped

with a cord having an equipment-grounding conductor and grounding plug. The plug must be

inserted into an appropriate outlet that is properly installed and grounded in accordance with all

local codes and ordinances.

WARNING: Improper connection of the equipment-grounding conductor can result

in a risk of electric shock. Check with a qualified electrician or service person if you

are in doubt as to whether the outlet is properly grounded. Do not modify the plug

provided with the appliance - if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounding attachment

plug that looks like the plug illustrated at right. Make sure that the appliance is

connected to an outlet having the same configuration as the plug. No adaptor should

be used with this appliance.

SAVE THESE INSTRUCTIONS

For Household or Commercial Use Only

PARTS AND COMPONENTS

Technical Specifications

Voltage: 120V., 60Hz.

Power: 8.3 Amps, 1000 Watts

* Illustrations may differ from actual product.

Note: Verify that all parts and components are included before assembly.

Caddy Parts

Vacuum

1. Canister

2. Hose Intake

3. Locking Clasp

4. Canister Handle (x2)

5. Power Cord and Hose Storage

6. On/Off Power Switch

7. Flexible Hose

8. Extension Tubes (x2)

9. Crevice Tool

10. Floor to Carpet Brush

11. Squeegee Brush

12. Filter Cartridge

13. Dust Bag

14. Foam Filter

Caddy Hardware

A. Cotter Pins (x2)

B. Flat Washers (x4)

C. Bolt / Lock Washer / Nut (x4)

D. Caddy Support Brackets (x2)

E. Bolt / Lock Washer / Nut for Caster (x2)

F. Hex. Slot Head Screw

G. Caster Assembly

H. Bracket Cover

I. Wrench

Vacuum Parts

Caddy Parts

15. Caddy Handle

16. Caddy Support (Left)

17. Caddy Support (Right)

18. Rear Caddy Frame

19. Front Caddy Frame

20. Axel

21. Rear Wheels (x2)

Caddy Hardware

Rear Caddy

(outside)

Fig. 2

ASSEMBLING THE CADDY

Assembling the Caddy

Your vacuum cleaner requires some assembly.

Ensure that all parts listed on the “Parts and

Components” page are included in the packaging.

Tools Required for Assembly

2. Make sure the notches on the caddy frame

pieces are sitting open side up. Fit the front

caddy frame into the rear caddy frame. (Fig. 2)

3. Place the right support on the inside of the right

side of the caddy frame, aligning all openings.

Note: The front caddy support will have to be

squeezed to join with rear caddy support.

4. Secure the right support with bolt and lock

washer. [C]

5. On the inside place a washer onto the bolt and

fasten with locking nut [C]. (Fig. 2)

Cotter Pin

Flat Washer

Axel

Cotter Pin

Flat Washer

Fig. 4

13. Assemble the bracket cover [I] on the caster

bracket and then use the screw [F] to fasten.

(Fig. 5)

1. Assemble the caddy frame first. Parts required

for this step:

- caddy support (left)

- caddy support (right)

- rear caddy frame and front caddy frame

- 4 Bolt / Lock Washer / Locking Nut (Fig. 1)

Phillips Screwdriver

(not included)

6. Repeat with the left support securing to the caddy

frame.

7. Ensure all fastenings are tight using a Phillips

screw driver (not included) and the wrench

(included).

8. Slide the axel through the holes in the rear frame.

(Fig. 4)

9. On the outside side of the axel, place a washer in

the groove nearest to the frame. (Fig. 3)

Right

Support

Left

Support

Rear Caddy

Frame

Front Caddy

Frame

4 Bolts

4 Lock Washers

4 Locking Nuts

Fig. 1

Notches

Open Side Up

Front Caddy

(center)

Left Support

(inside)

Fig. 3

Flat Washer

Axel

Rear Caddy

Frame

Front Caddy

Frame

Wrench

(included)

10. Slide a rear wheel onto each side of the axel.

11. Place a flat washer against the outside of each

wheel onto the axel. Repeat on the opposite side

wheel.

12. Secure each wheel with a cotter pin placed in the

hole and wrapped around the axel to secure the

wheel to the axel. (Fig. 4)

Fig. 5

Filter

Cartridge

Locking

Knob

Fig. 13

Fig. 9

ASSEMBLING THE CADDY

Assemble the Vacuum to the Caddy

1. Make sure that the hose intake is facing forwards

and the wheels are at the rear of the unit. Using the

handles on the canister, carefully lower it onto the

frame aligning the canister edge with the notches in

the frame. (Fig. 6)

2. To attach the canister to the handle supports, align

the canister brackets on each side of canister with

the supports. (Fig. 7)

3. With the clamp assembly tabs facing downwards,

slide a clamp assembly onto the right and left

caddy support. (Fig. 7)

4. Place the clamp assembly tabs onto the canister

brackets on each side of the canister.

5. Tighten the clamp assembly by turning the hand nut

clockwise until it is secured on the supports. (Fig. 8)

Filter Assembly

This wet/dry vacuum requires different filter assembly

for wet or dry pick-up. The filter cartridge and dust bag

are required for dry pick-up. (Fig. 10) The foam filter is

required for wet pick-up. (Fig. 11)

Fig. 12

Fig. 6

Notches on Caddy

Notches Notches

Fig. 7

Clamp

Assembly

Tabs

Canister Bracket

6. To insert the caddy handle onto the right and left

caddy supports, fit the ends of the caddy handle

into the openings of the left and right caddy supports

and push down until the caddy handle clicks into

place. (Fig. 9)

Fig. 8

Hand Nut

Filter Cartridge Dust Bag

Foam Filter

Fig. 10

Dry Pick-UP Wet Pick-UP

Fig. 11

For Dry Pick-Up

Warning: To reduce risk of

electric shock - unplug before

cleaning, assembly or emptying

canister.

1. To assemble the filter for

dry pick up, turn the filter

holder upside down on a

level surface. (Fig. 12)

2. Place the filter cartridge

onto the filter holder,

ensuring that the locking tab

inside the filter cartridge is

aligned with the slot on the

filter holder and turn the

locking knob until it stops.

(Fig. 13)

Important: Do not operate

the vacuum without the filter

cartridge and dust bag in

place for dry pick-up

Operating Your Wet/Dry Vacuum

Warning: To reduce the risk of fire or explosion, do

not operate this unit in areas with flammable gases,

vapors or explosive dust in the air. Flammable gases or

vapors include but are not limited to: lighter fluid,

solvent type cleaners, oil base paints, gasoline, alcohol

or aerosol sprays. Explosive dusts include but are not

limited to; coal, magnesium, grain or gun powder. Do

not vacuum explosive dust, flammable or combustible

liquids or hot ashes. To reduce the risk of health

hazards from vapors or dusts, do not vacuum toxic

materials.

Attachments

Floor to Carpet Brush – Used for

dry pick-up. To use for carpets

press toggle switch down to the

front of the brush to raise the bristles;

to switch to bare floor setting

press the toggle switch to the

back of the brush to lower the bristles.

Crevice Tool – Use for wet or dry

pick-up in tight corners, good for

automobiles etc.

Squeegee - Use for wet pick-up

on flat surfaces to pick up liquids

and dry the surface quicker.

Extension Tubes – For an extended

reach insert one or two of the extension

tubes onto the flexible hose. Slide one

tube into the other, then slide the

extension tube assembly into

the handle end of the flexible hose.

Attachments slide easily onto the handle end of the

flexible hose or the extension tubes.

OPERATING INSTRUCTIONS

Assemble the Hose

1. Insert the wide end of the hose into the hose

intake. (Fig. 17)

2. Attach one of the extension tubes onto the handle

part of the flexible hose. (Fig. 18)

Fig. 15

Locking

Clasp

For Wet Pick-Up

Warning: To reduce risk of electric shock -

unplug before cleaning, assembly or emptying

canister.

1. To assemble the filter for wet pick

up, turn the filter holder upside

down on a level surface. (Fig. 12)

2. Remove the dust bag and filter

cartridge from the filter holder.

3. Place the foam filter over the

filter holder. (Fig. 16)

Important: Do not use the filter

cartridge or the dust bag for wet

pick-up.

4. Ensure that the foam filter is all the way down on

the filter holder.

5. Follow the instructions from the “For Dry Pick-Up”

section to assemble the filter holder onto the

canister.

Warning: If water is seen to be coming from the

exhaust - immediately turn the unit off and unplug from

electrical outlet. Empty canister and clean.

Important: This unit is supplied with a safety feature

that will stop air flow if the tank is overfilled or tips

over. If the airflow is stopped, turn the vacuum off,

empty the canister, then reassemble the vacuum and

continue vacuuming.

3. For a longer reach you can attach the other

extension tube to the first one.

4. Attach the desired attachment for the task onto the

end of the extension tube or directly onto the

handle of the flexible hose. (Fig. 19)

Fig. 17

Fig. 19

Toggle Switch

Fig. 16

Fig. 14

3. Place the dust bag onto the

filter cartridge, ensuring that

the elastic at the bottom of

the bag is at the bottom

of the filter. (Fig. 14)

4. Turn the filter holder over

and place in the vacuum

canister with the power

cord in the rear.

Warning: Grasp the power

cord and hose storage on the filter holder to place the

assembly into the canister, as cuts may occur from

edge of filter holder.

5. Secure the filter

holder with the

three (3) locking

clasps. (Fig. 12)

Fig. 18

Fig. 20

OPERATING INSTRUCTIONS

Cleaning and Maintenance

Warning: To reduce risk of electric shock - unplug

before cleaning, assembly or emptying canister.

Warning: To reduce the risk of back injuries or

falls, never lift the vacuum if the canister is full of

liquid or debris because it is heavy. Scoop or drain

enough of the contents to lighten the canister

enough so that it can be lifted comfortably.

1. Turn the unit “Off”.

2. Unplug unit from electrical wall outlet.

3. To empty the canister, first remove the filter holder

from the canister.

4. Lift canister off of the caddy and empty into the

appropriate waste container.

5. When emptying liquids from the canister it is

suggested that the canister be tipped over carefully

so that liquid could spill into a drain pipe.

Warning: Be careful not to empty any liquid onto the

power cord or the filter holder as this could damage the

motor.

Warning: Lifting heavy objects can cause injury.

Empty frequently to avoid excessive weight.

Cleaning / Replacing Foam Filter

1. Turn the unit “Off”.

2. Unplug the unit from the electrical outlet.

3. Remove the filter holder from the canister

4. Remove the foam filter from the filter holder.

4. The foam filter should be cleaned after every use. A

severely soiled or clogged filter should be thoroughly

washed with fresh tepid water. A mild detergent may

be used if required. (Fig. 20)

5. Let the foam filter air dry completely before replacing

into the vacuum. (Fig. 21) Do not use a washing

machine to wash or rinse the filter. Do not use a hair

dryer to dry it. Air dry only. Never operate the

vacuum for wet pickup without the foam filter in

place.

Dry Material Vacuuming

Warning: To reduce risk of electric shock -

unplug before cleaning or emptying canister.

Caution: To reduce the risk of hearing damage wear

ear protectors when using the unit for extended

periods of time or when in a noisy area. The operation

of any utility vacuum can result in foreign objects being

blown into the eyes, which can result in severe eye

damage. Always wear safety goggles complying with

ANSI Z87.1 (or in Canada CSA Z94-3-M88) shown on

the package before commencing operation.

Caution: To avoid damage to the motor only use the

filter cartridge and dust bag for dry pick- up.

Note: To dry the unit if your vacuum was recently

used for wet pick-up, run the vacuum with the filter

cartridge and dust bag in place without the hose

attached for approximately 10 minutes. The air

circulating through the unit will dry it.

1. Ensure that the filter cartridge and dust bag are

correctly installed to avoid leaks and possible

motor damage to the vacuum.

2. Attach the flexible hose, extension tube(s) and

desired attachment.

3. Plug unit into electrical wall outlet. Turn the power

On/Off switch to the “On” position.

4. To keep your unit in good running order, empty the

canister and clean the dust bag and filter cartridge

frequently, especially when using to pick up fine

dust or fine debris. This will prevent a build up of

mold or mildew.

Liquid or Wet Vacuuming

Warning: Do not vacuum up flammable or

combustible liquids such as gasoline or use in

areas where they may be present.

Caution: To avoid damage to the unit always use

the foam filter for wet pick-up.

1. Unplug unit from electrical wall outlet.

2. Place the foam filter on the filter holder and secure

the filter holder into place on the canister.

3. Attach the flexible hose, extension tube(s) and

desired attachment.

4. Plug unit into electrical wall outlet, and turn the

On/Off power switch to the “On” position.

5. When vacuuming up large amounts of liquid,

make sure that the canister is not too full to avoid

injury when emptying the canister.

Caution: Avoid tipping the unit when full of water.

6. If the liquid being vacuumed passes a specified

amount, a float valve will rise automatically and

cut off the airflow to the unit. If this occurs, turn

the unit “Off” and unplug the power cord. Empty

the canister of any liquid. The float valve will go

down after the unit is turned off.

7. When finished vacuuming up the liquids, empty

the canister, remove the flexible hose and run the

vacuum for approximately 10 minutes to dry the

foam filter. This will prevent a build up of mold or

mildew.

Fig. 21

OPERATING INSTRUCTIONS

Cleaning / Replacing Filter Cartridge / Dust

Bag

Warning: To reduce risk of electric shock - unplug

before cleaning, assembly or emptying canister.

Warning: If picking up any type of renovating dust a

protective mask should be worn.

The filter cartridge is washable. It should, however, be

replaced every three (3) to six (6) months depending on

usage to ensure peak performance of your vacuum.

Cleaning and Replacing the Filter Cartridge:

1. Turn the unit “Off”.

2. Unplug the unit from the electrical outlet.

3. Remove the filter holder from the canister.

4. Remove the dust bag from the filter holder.

5. Turn the locking knob to unlock the filter cartridge

from the filter holder. (Fig. 22)

Filter

Cartridge

Locking

Knob

Fig. 22

6. Vigorously “TapClean” the filter cartridge on a

hard surface until no more dust is observed falling

out from between the pleats of the filter.

7. Replace the dust bag over the filter cartridge.

8. Replace the filter cartridge and reinstall the filter

holder in the vacuum. (not shown)

9. Turn the locking knob to lock the filter cartridge

from the filter holder. (Fig. 22)

Cleaning and Replacing the Dust Bag:

1. Turn the unit “Off”.

2. Unplug the unit from the electrical outlet.

3. Remove the filter holder from the canister.

4. Remove the dust bag from the filter holder.

5. Wash the dust bag in lukewarm water.

6. Let the dust bag air dry completely before

reinstalling onto the filter holder.

Note: The dust bag is washable but it should be

replaced every three (3) to six (6) months depending

on usage.

Motor Thermostat

Important: This unit is equipped with a motor protective

thermostat. If some reason the wet/dry vacuum should

overheat, the thermostat will automatically turn the unit off.

Should this occur:

• Push the On/Off switch once.

• Disconnect the plug from the power source.

• Check the source of overheating problem. (i.e. clogged

hose or filter).

• Wait at least 45 minutes before attempting to reuse the

vacuum.

• After unit has cooled down for 45 minutes, plug in the

vacuum and push the On/Off switch to the “On”

position. The vacuum should start again.

• If the vacuum still does not start, contact customer

service at 1 (800) 275-9251.

PROBLEM POSSIBLE REASON POSSIBLE SOLUTION

VACUUM WILL NOT

OPERATE

1. Power cord not firmly

plugged into outlet.

2. No power in wall outlet.

3. Needs servicing.

4. Thermostat has tripped.

1. Plug unit in firmly.

2. Check fuse or breaker.

Replace fuse/reset breaker.

3. Call 1 (800) 275-9251.

4. Turn the unit off and unplug

from outlet. Allow unit to cool

down, then restart.

VACUUM WILL NOT

PICK-UP OR

SUCTION POWER

IS WEAK

1. Canister is full.

2. Unit clogged.

3. Flexible hose / extension

tube clogged.

1. Empty canister.

2. Turn unit off and unplug from

wall outlet. Check for object(s

)

in air duct and remove.

3. Turn unit off and unplug from

wall outlet. Check for objects

in flexible hose / extension

tube.

WATER ESCAPING

FROM THE

EXHAUST

1. The canister is full. 1. Empty the canister.

Please Note: Filter cartridge, foam filter and dust bag are washable. They should,

however, be replaced every three (3) to six (6) months, depending on usage, to ensure

peak performance of your vacuum.

Important: Make sure that dust bag and the foam filter have completely air dried before

re-installing back into the vacuum.

Tel.: 1 (800) 275-9251

Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time

TO ORDER REPLACEMENT FILTER CARTRIDGE, FOAM FILTER

OR DUST BAGS OR FOR TECHNICAL SUPPORT

for Model CW233H

TROUBLESHOOTING GUIDE

ORDERING REPLACEMENT PARTS

Printed in China

Model

CW233H

THREE (3) YEAR LIMITED WARRANTY

FANTOM warrants this product to be free from defects in material and workmanship for a period of three (3) years

from the date of the original purchase. This warranty applies only to normal domestic household use.

Should your appliance fail to operate properly while in use under normal commercial or household conditions within

the warranty period, return the complete appliance and accessories, freight prepaid to:

FANTOM, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901

If the appliance is found by FANTOM to be defective in material or workmanship, FANTOM will repair or replace it

free of charge. Proof of purchase date must be included. *

Non-durable parts including, without limitation, dust bags, filters, brushes and electrical parts which normally require

replacement are specifically excluded from warranty.

The liability of FANTOM is limited solely to the cost of the repair or replacement of the unit at our option. This

warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for

commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or

damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by

or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have

been performed by a repair person not authorized by FANTOM.

This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional

warranties. The responsibility of FANTOM if any, is limited to the specific obligations expressly assumed by it under

the terms of the limited warranty. In no event is FANTOM liable for incidental or consequential damages of any

nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so

the above may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and

to attach tag to item before packing with your name, complete address and phone number with a note giving

purchase information, model number and what you believe is the problem with item. We recommend you

insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your

package “ATTENTION CUSTOMER SERVICE”.

We are constantly striving to improve our products, therefore the specifications contained herein are subject to

change without notice.

yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy

OWNERSHIP REGISTRATION CARD

Please fill out and mail the product registration card within ten (10) days of purchase. The registration will enable us to

contact you in the unlikely event of a product safety notification. By returning this card you acknowledge to have read

and understood the instructions for use, and warnings set forth in the accompanying instructions.

RETURN TO FANTOM: 94 Main Mill Street, Door 16, Plattsburgh, NY 12901

______________________________________________________________________________________________

Appliance model

_______________________________________________________________________________________________________

Date purchased Name of store

_______________________________________________________________________________________________________

Owner’s name

_______________________________________________________________________________________________________

Address City State Zip Code

Model CW233H

Fantom CW233H User manual

Brand: Fantom

Model: CW233H

Category: Vacuum cleaners

Type: User manual

Download PDF

report

Fantom CW233H User manual

Fantom CW233H User manual

Related papers

Other documents