Sherwood RD-7503 User manual

RD-7503

cover_7503A 2008.10.29 6:21 PM 페이지 1

ENGLISH

2

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other.

A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit

into your outlet, consult an electrician for replacement of

the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the

apparatus.

When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus have been

exposed to rain or moisture, does not operate normally,

or has been dropped.

PORTABLE CART WARNING

RD-7503(A) 2008.11.4 1:45 PM 페이지 2

3

ENGLISH

Introduction

: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This symbol is intended to alert the user to the presence of

uninsulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

Caution regarding installation

Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure.

: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

WARNING

Do not block ventilation openings or stack other equipment on the top.

READ THIS BEFORE OPERATING YOUR UNIT

Note to CATV System Installer :

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper

grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point

of cable entry as practical.

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

FOR YOUR SAFETY

Units shipped to the U.S.A and CANADA are designed for operation

on 120 V AC only.

Safety precaution with use of a polarized AC plug.

However, some products may be supplied with a nonpolarized plug.

U.S.A

CANADA

120 V

•

Leave a space around the unit for sufficient ventilation.

•

Avoid installation in extremely hot or cold locations, or in an area

that is exposed to direct sunlight or heating equipment.

•

Keep the unit free from moisture, water, and dust.

•

Do not let foreign objects in the unit.

•

The ventilation should not be impeded by covering the ventilation

openings with items, such as newspapers, table-cloths, curtains, etc.

•

No naked flame sources, such as lighted candles, should be placed

on the unit.

•

Please be care the environmental aspects of battery disposal.

•

The unit shall not be exposed to dripping or splashing for use.

•

No objects filled with liquids, such as vases, shall be placed on the

unit.

• Do not let insecticides, benzene, and thinner come in contact with

the set

.

•

Never disassemble or modify the unit in any way.

Notes on the AC power cord and the wall outlet.

•

The unit is not disconnected from the AC power source(mains) as

long as it is connected to the wall outlet, even if the unit has been

turned off.

•

To completely disconnect this product from the mains, disconnect

the plug from the wall socket outlet.

•

When setting up this product, make sure that the AC outlet you are

using is easily acceptable.

•

Disconnect the plug from the wall outlet when not using the unit for

long periods of time.

CAUTION

: To prevent electric shock, match wide blade of

plug to wide slot, fully insert.

: Pour éviter chocs électriques, introduire la lame

la plus large de la fiche dans la borne

correspondante de la prise et pousser jusqu’ au

fond.

E

NERGY

S

TAR



is a U.S. registered mark. As an

E

NERGY

S

TAR



Partner, Sherwood has

determined that this product meets the

E

NERGY

S

TAR



guidelines for energy efficiency.

CAUTION

ATTENTION

RD-7503(A) 2008.11.4 1:45 PM 페이지 3

ENGLISH

4

CONTENTS

• IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

• Introduction

READ THIS BEFORE OPERATING YOUR UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

• System Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

• Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

• Universal Remote Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

OPERATING COMPONENTS WITH REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

REMOTE CONTROL OPERATION RANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

LOADING BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

USING FUNCTIONS OF REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

• Operations

LISTENING TO A PROGRAM SOURCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

SURROUND SOUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

ENJOYING SURROUND SOUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

LISTENING TO RADIO BROADCASTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

LISTENING TO SIRIUS SATELLITE RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

(SIRIUS Satellite Radio (only for North America))

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

DIGITAL AUDIO RECORDING WITH MD RECORDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

OTHER FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

ROOM 2 SOURCE PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

• OSD Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

SETTING THE SYSTEM SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

SETTING THE INPUT SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

SETTING THE SPEAKER / ROOM EQ SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

SETTING THE CH LEVEL SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

SETTING THE SOUND PARAMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

SETTING THE MULTI ROOM SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

• Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

• Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

• Setup Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

RD-7503(A) 2008.11.4 1:45 PM 페이지 4

5

ENGLISH

System Connections

• Please be certain that this unit is unplugged from the AC outlet before making any connections.

• Since different components often have different terminal names, carefully read the operating instructions of the component

connected.

• Be sure to observe the color coding when connecting audio, video and speaker cords.

• Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver.

• Change the position of the FM indoor antenna until you

get the best reception of your favorite FM stations.

• Place the AM loop antenna as far as possible from the receiv-

er, TV set, speaker cords and the AC input cord and set it to a

direction for the best reception.

• If the reception is poor with the AM loop antenna, an AM out-

door antenna can be used in place of the AM loop antenna.

• A 75Ω outdoor FM antenna may be used to further

improve the reception. Disconnect the indoor antenna

before replacing it with the outdoor one.

1.CONNECTING ANTENNAS

RD-7503(A) 2008.11.4 1:45 PM 페이지 5

6

• The jacks of VIDEO 1 may also be connected to a DVD recorder or other digital video recording component. For details, refer

to the operating instructions of the component to be connected.

• The jacks of VIDEO 2/VIDEO 3 can also be connected to an additional video component such as a cable TV tuner or satellite

system.

• Connect the jacks of VIDEO 3 to the video component in the same way.

• There are three types of video jacks (COMPONENT, S-VIDEO, (composite) VIDEO) for analog video connections and the

HDMI connectors for digital video and audio connections.

Connect them to the corresponding video jacks according to their capability.

• For your reference, the excellence in picture quality is as follows : "HDMI” > "COMPONENT" > "S-VIDEO" > "(composite)

VIDEO" .

• When making COMPONENT VIDEO connections, connect "Y" to "Y", "PB/C

B" to "CB"(or "B-Y", "PB") and "PR/C

R" to "CR"(or

"R-Y", "P

R").

• When recording video program sources through VIDEO 1 OUT jack or viewing video program sources through MONITOR

OUT or ROOM 2 OUT jack, you must use the same type of video jacks that you did connect to video playback components

such as DVD player, cable TV tuner, etc.

Notes :

• You can connect Apple iPod to this receiver via Sherwood iPod dock. If Sherwood iPod dock is connected to DIGI LINK-i jack

for system control, you should connect its video and audio jacks to the "VIDEO 2" jacks of this receiver. Because, when you

control your iPod with the unit's remote control, the VIDEO 2/iPod is automatically selected as an input source and the

corresponding operation is performed.

• The OSD menu and the momentary OSD can be displayed via the (composite) VIDEO MONITOR OUT only.

2.CONNECTING VIDEO COMPONENTS

ENGLISH

RD-7503(A) 2008.11.4 1:45 PM 페이지 6

7

HDMI (High Definition Multimedia Interface) connection : (*1)

• You can connect the source component (DVD player, etc.) to the display component (TV, projector, etc.) through this receiver

with using a commercially available HDMI cord.

• The HDMI connection can carry uncompressed digital video signals and digital audio signals.

• The HDMI video stream signals (video signals) are theoretically compatible with DVI-D. When connecting to a TV monitor,

etc., equipped with DVI-D connector, it is possible to connect using a commercially available HDMI-DVI converter cord.

Since the HDMI-to-DVI connection cannot carry any audio signals, you should make audio connections to play the audio

signals on the component equipped with DVI-D connector. (For details, refer to the operating instructions of its.)

• If you connect the HDMI INs to your video components, it is easier to do so following the default settings.

• If your HDMI connection is different from the default setting, you should assign the HDMI INs you used with the "When

selecting the HDMI ASSIGN" procedure on page 46.

• The default settings are as follows :

HDMI 1 : VIDEO 1, HDMI 2 : VIDEO 2/iPod, HDMI 3 : VIDEO 3

Copyright protection system

• This unit supports HDCP (High-bandwidth Digital Contents Protection), technology to protect copyright of digital video signals

against illegal duplication. HDCP must also be supported on the components connected to this unit.

• This unit is HDMI Ver. 1.3 compatible.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing

LLC.

Notes :

• For stable signal transfer, we recommend using HDMI cords that are a maximum of 5 meters in length.

• Among the components that support HDMI, some components can control other components via the HDMI connector.

However, this unit cannot be controlled by another component via the HDMI connector.

• The audio signals from the HDMI connector (including the sampling frequency and bit length) may be limited by the

component that is connected.

• The video signals will not be output properly if a component incompatible with HDCP is connected.

• If the resolutions of the video signals which are output from the MONITOR OUTs and your monitor TV are not matched, the

picture is not clear, natural or displayed. In this case, change the setting of the resolution on the source component (DVD

player, etc.) to one which the monitor TV can handle. (For details, refer to the operating instructions of the source component.)

• When you want to enjoy only the picture on your TV, not the sound, you should set the HDMI AUDIO OUT to OFF not to

output the digital audio signal from the HDMI MONITOR OUT of this receiver. (For details, refer to "When selecting the HDMI

AUDIO OUT" on page 42.)

Component video input default settings: (*2)

• If you connect the COMPONENT VIDEO INs to your video components, it is easier to do so following the default settings.

• If your component video connections are different from the default setting, you should assign the COMPONENT VIDEO INs

you used with the "When selecting the VIDEO ASSIGN" procedure on page 46.

• The default settings are as follows:

COMPONENT IN 1 : VIDEO 1, COMPONENT IN 2 : VIDEO 2/iPod

Continued

ENGLISH

• When recording audio signals, connect the AUDIO IN/OUT jacks of 'VIDEO 1" to audio recording equipment such as a tape

deck, an MD recorder, etc.

3.CONNECTING AUDIO COMPONENTS

RD-7503(A) 2008.11.4 1:45 PM 페이지 7

8

• Use these jacks to connect the corresponding outputs

of a DVD player or external decoder, etc. that has 6, 7

or 8 channel analog audio outputs.

• In case of 6 or 7 channel outputs, do not connect both

of the SURROUND BACK L and R inputs or the

SURROUND BACK R input of this unit. (For details,

refer to the operating instructions of the component to

be connected.)

4.CONNECTING EXTERNAL INS

• The OPTICAL and the COAXIAL DIGITAL OUTs of the

components that are connected to this unit can be

connected to these DIGITAL INs.

• A digital input should be connected to the components

such as a CD player, DVD player, etc. capable of

outputting DTS Digital Surround, Dolby Digital or PCM

format digital signals, etc.

• If the component with OPTICAL IN jack is connected to

the OPTICAL OUT jack of this unit, you can record the

high quality sound of CDs, etc. without degradation.

• For details, refer to the operating instructions of the

component connected.

• When making the COAXIAL DIGITAL connection, be

sure to use a 75 Ω COAXIAL cord, not a conventional

AUDIO cord.

• All of the commercially available optical fiber cords

cannot be used for the equipment. If there is an optical

fiber cord which cannot be connected to your equipment,

consult your dealer or nearest service organization.

Notes :

• Be sure to make either a OPTICAL or a COAXIAL DIGITAL connection on each component. (You don’t need to do both.)

• Depending on the digital audio signal format input into the HDMI IN connector, some digital signals cannot be output from

the OPTICAL OUT jack.

�Digital input default settings

• If you connect the DIGITAL INs to your components, it is easier to do so following the default settings.

• If your DIGITAL connections are different from default settings, you should assign the DIGITAL INs you used with the

"When selecting the AUDIO ASSIGN" procedure on page 46.

• The default settings are as follows :

OPTICAL IN 1:VIDEO 1, OPTICAL IN 2:VIDEO 2/iPod, COAXIAL IN 1 : CD, COAXIAL IN 2 : F. AUX

5.CONNECTING DIGITAL INS AND OUT

ENGLISH

RD-7503(A) 2008.11.4 1:45 PM 페이지 8

9

• Be sure to connect speakers firmly and correctly

according to the channel(left and right) and the

polarity (+ and -). If the connections are faulty,

no sound will be heard from the speakers, and if

the polarity of the speaker connection is

incorrect, the sound will be unnatural and lack

bass.

• For installing the speakers, refer to "Speaker

placement" on page 10.

• After installing the speakers, first adjust the

speaker settings according to your environment

and speaker layout. (For details, refer to

"SETTING THE SPEAKER /ROOM EQ SETUP"

on page 51.)

Surround back speakers

• When using only one surround back speaker,

you should connect it to SURROUND BACK/

MULTI LEFT channel.

• Because this receiver cannot drive the surround

back speakers and the ROOM 2 speakers

simultaneously, you should assign their power

amplifier correctly depending on how to use

them. (For details, refer to "CONNECTING

ROOM 2 OUTS" on page 11 and "When

selecting the AMP ASSIGN" on page 41.)

Front Bi-Amp Connections.

• Some speakers are equipped with two sets of

input terminals, for bi-amplification.

• If no other surround back speakers are used,

you can connect the FRONT and the

SURROUND BACK/MULTI channels to the bi-

amp-capable speakers. (For details, refer to the

operating instructions of your bi-amp-capable

speakers.)

• To drive the bi-amp-capable speakers, you

should assign the power amplifier to "BI-AMP".

Note :

• Before making bi-amp connections, remove the

short-circuiting bars from the terminals of your

speakers.

Caution :

• Be sure to use the speakers with the impedance

of 6 ohms or above.

• Do not let the bare speaker wires touch each

other or any metal part of this unit. This could

damage this unit and/or the speakers.

• Never touch the speaker terminals while the AC

input cord is connected to the wall AC outlet.

Doing so could result in electric shocks.

6.CONNECTING SPEAKERS

ENGLISH

RD-7503(A) 2008.11.4 1:45 PM 페이지 9

ENGLISH

10

Speaker placement

1. TV or Screen

2. Front left speaker

3. Subwoofer

4. Center speaker

5. Front right speaker

6. Surround left speaker

7. Surround right speaker

8. Surround back left speaker

9. Surround back right speaker

10. Surround center speaker

11. Listening position

Ideal speaker placement varies depending on the size of

your room and the wall coverings, etc. The typical example

of speaker placement and recommendations are as follows :

Front left and right speakers and center speaker

• Place the front speakers with their front surfaces as flush

with TV or monitor screen as possible.

• Place the center speaker between the front left and right

speakers and no further from the listening position than

the front speakers.

• Place each speaker so that sound is aimed at the location

of the listener’s ears when at the main listening position.

Surround left and right speakers

• Place the surround speakers approximately 1 meter (40

inches) above the ear level of a seated listener on the

direct left and right of them or slightly behind.

Surround back left and right speakers

• Place the surround back speakers at the back facing the

front at a narrower distance than front speakers.

• When using a single surround back speaker, place it at the

rear center facing the front at a slightly higher position (0

to 20 cm ) than the surround speakers.

• We recommend installing the surround back speaker(s) at

a slightly downward facing angle. This effectively prevents

the surround back channel signals from reflecting off the

TV or screen at the front center, resulting in interference

and making the sense of movement from the front to the

back less sharp.

Subwoofer

• The subwoofer reproduces powerful deep bass sounds.

Place a subwoofer anywhere in the front as desired.

Notes :

When using a conventional TV, to avoid interference with

the TV picture, use only magnetically shielded front

left and right and center speakers.

To obtain the best surround effects, the speakers except

the subwoofer should be full range speakers.

Continued

�Connecting speaker wire

1. Strip away approx. 10 mm

(3/8 inch) of wire insulation,

then twist the wire ends

tight.

2. Lossen by turning the

speaker terminal counter-

clockwise.

3. Insert the bare part of the

wire.

4. Tighten by turning it

clockwise.

7. CONNECTING SUBWOOFER PRE OUT

• To emphasize the deep bass sounds, connect a powered

subwoofer.

RD-7503(A) 2008.11.4 1:45 PM 페이지 10

11

9.CONNECTING DC TRIGGER OUT

• Connect a component to DC TRIGGER OUT jack

that allows DC 12V to turn on when a specific

input source is selected.

• For details, refer to the operating instructions of

the components to be connected.

• To link DC TRIGGER OUT with a specific input

source, refer to "When selecting the DC

TRIGGER" on page 47.

Notes :

• This output voltage (12V d.c., 100mA) is for (status) control only, it is not sufficient for drive capability.

• When making DC TRIGGER connection, you should use the stereo mini cord, not a mono mini cord.

ENGLISH

• ROOM 2 playback feature allows you to play a different program source in another room as well as one source in the main

room at the same time.

• For ROOM 2 playback, connect the ROOM 2 OUT jacks to the amplifier, TV, etc. installed in another room, or

connect the ROOM 2 speaker terminals to the speakers.

• Because this receiver cannot drive the surround back speakers and the ROOM 2 speakers simultaneously, you should

assign their power amplifier correctly depending on how to use them. (For details, refer to "When selecting the AMP

ASSIGN" on page 41.)

Notes :

• To minimize hum or noise, use high quality connection cords.

• You cannot use the digital audio signal for ROOM 2 playback.

8.CONNECTING ROOM 2 OUTS

RD-7503(A) 2008.11.4 1:45 PM 페이지 11

ENGLISH

12

• Connect the SIRIUS connector to the Sirius Connect

Home Tuner kit (sold separately).

• Position the Home Tuner antenna near a south-facing

window to receive the best signal.

When making connections, also refer to the operating

instructions of the SiriusConnect Home Tuner.

• To listen to SIRIUS Satellite Radio, refer to "SIRIUS

Satellite Radio (only for North America)" on page 31.

11. CONNECTING SIRIUS CONNECTOR (only for North America)

10.CONNECTING FOR SYSTEM CONTROL

• Connect this jack to the DIGI LINK-i jack of Sherwood

iPod dock that allows you to control the iPod with the

unit's remote control.

Positioning the antenna

• For a consistent satellite signal, the antenna must be

positioned correctly. Use the following map to determine

which area you are in and position the antenna

accordingly.

• Area 1 : Point the antenna toward the sky in the east,

notrtheast, or southeast, either through a window or

out side.

• Area 2 : Point the antenna toward the sky in the north

or northeast, either through a window or outside.

• Area 3 : Point the antenna toward the sky in the north

or northwest, either through a window or outside.

• Area 4 : Point the antenna toward the sky in the west,

northwest, or southwest, either through a window or

outside.

• Area 5 : Put the antenna outside and point it straight

up. The antenna cannot be used indoors.

12.AC INPUT CORD

• Plug this cord into a wall AC outlet.

SiriusConnect Home Tuner

To a wall AC

outlet

RD-7503(A) 2008.11.4 1:45 PM 페이지 12

13

Front Panel Controls

1. POWER switch

2. POWER ON/STANDBY button

3. STANDBY indicator

4. INPUT SELECTOR knob

5. BAND button

6. EXTERNAL IN button

7. SURROUND MODE/CONTROL DOWN() button

8. STEREO/CONTROL UP() button

9. MASTER VOLUME CONTROL knob

10. MULTI CONTROL knob()

11. HEADPHONE jack

12. SPEAKER button

13. ROOM 2 button

14. CHANNEL LEVEL button

15. SETUP button

16. MEMORY/ENTER button

17. TUNING UP(+)/DOWN(-) buttons

18. PRESET UP(+)/DOWN(-) buttons

19. AUDIO ASSIGN button

20. SETUP MIC jack

For details, see next page.

21. FRONT AUX IN jack

For details, see next page.

22. Bluetooth IN connector

For details, see next page.

23. SPEAKER indicator

24. REMOTE SENSOR

25. FLUORESCENT DISPLAY

For details, see next page.

ENGLISH

FLUORESCENT DISPLAY

1. Input, frequency, volume level, operating information, etc.

2. Surround mode indicators

3. AUTO indicator

4. DIGITAL input indicator

5. DIRECT indicator

6. Preset number, sleep time display

7. PRESET indicator

8. MEMORY indicator

9. SLEEP indicator

10. ROOM 2 indicator

11. TUNED indicator

12. STEREO indicator

RD-7503(A) 2008.11.4 1:45 PM 페이지 13

ENGLISH

14

• The FRONT AUX IN jack can be connected to additional audio components such as an MP3 player, etc.

� Note :

• When connecting this jack to an MP3 player, etc., you should use the stereo mini cord, not a mono mini cord.

� FRONT AUX IN JACK

Microphone

• To use Auto Setup function, connect the supplied microphone to the SETUP MIC jack.(For details, refer to "When

selecting the AUTO SETUP" on page 51.)

Notes:

• Because the microphone for Auto Setup is designed for use with this receiver, do not use a microphone other than

the one supplied with this receiver.

• After you have completed the auto setup procedure, disconnect the microphone.

� SETUP MIC JACK

Bluetooth IN CONNECTOR

• If the Bluetooth IN connector is connected to Sherwood Audio Receiver

BT-R7(sold separately) with Bluetooth wireless technology, you can enjoy

music wirelessly with a music player featuring Bluetooth wireless

technology such as MP3 player, mobile phone, etc..

(For information on Sherwood Audio Receiver BT-R7, contact your dealer.)

• The Bluetooth word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc. and any use of such marks by Sherwood Corporation is

under license. Other trademarks and trade names are those of their

respective owners.

 Notes:

• For safe operation, turn the power off before connecting or disconnecting

the Audio Receiver BT-R7.

• When not using the Bluetooth IN connector, cover it with the supplied cap.

RD-7503(A) 2008.11.4 1:45 PM 페이지 14

ENGLISH

15

Universal Remote Controls

This universal remote control can operate not only this receiver but also most popular brands of audio and video components

such as iPod docks, TVs, DVD players, satellite receivers, cable boxes, etc.

• To operate 5 components other than this receiver, you should enter the setup code for each component.

(For details, refer to “USING FUNCTIONS OF REMOTE CONTROL” on page 18.)

• The numbered buttons on the remote control have different functions in different device modes. For details, refer to

"FUNCTION TABLE of the NUMBERED BUTTONS" on the next page.

STANDBY button

STEREO button

SLEEP button

EXTERNAL IN button

VOLUME UP/DOWN() buttons

MUTE button

CURSOR CONTROL(

ENTER</SEARCH MODE,

SELECT> buttons

The function in "< >" are regional option

for Notrh America

DIMMER button

DISPLAY button

ROOM 2 button

PRESET UP/DOWN(+/-) buttons

DEVICE buttons

To operate the desired component with

this remote control, first select the

corresponding DEVICE button.

SET LED

SURROUND MODE

UP/DOWN  buttons

POWER ON button

NUMERIC (0~9, +10)/

INPUT SELECTOR buttons

To select the desired input source

of TUNER~VIDEO 3

� Note :

• "VIDEO 4" is not available for

this receiver.

SETUP button

TEST TONE button

AUDIO ASSIGN button

CHANNEL LEVEL button

TUNING UP/DOWN(+/-) buttons

MACRO(M1~M3) buttons

To operate a macro function,

press the corresponding

MACRO button.

RD-7503(A) 2008.11.4 1:45 PM 페이지 15

ENGLISH

16

FUNCTION TABLE of the NUMBERED BUTTONS.

Notes :

• Some functions for each component may not be available or may work differently.

• Depending on other kinds of components that are available for each DEVICE button, some functions may not be available or

may work differently, too.

• For details about functions, refer to the operating instructions of each component.

(for iPod Dock)

PLAY LIST

UP/DOWN(</>)

DOCK MODE

ALBUM

UP/DOWN()

UP/DOWN(

ENTER

MENU

REPEAT

RANDOM

PLAY/PAUSE

REVERSE SKIP ( ) /

FORWARD SKIP ( )

(for DVD Player)

POWER ON

STANDBY

(POWER OFF)

NUMERIC

SETUP

CURSOR

CONTROL

ENTER

MENU

RETURN

DISPLAY

PAUSE

STOP

PLAY

REVERSE SERARCH( )/

FORWARD SEARCH( )

REVERSE SKIP( )/

FORWARD SKIP ( )

AUDIO

SUBTITLE

(for VCR)

POWER ON

STANDBY

(POWER OFF)

NUMERIC

CHANNEL

UP/DOWN()

VOLUME

UP/DOWN()

MUTE

INPUT

SELECTOR

RECORD

PAUSE

STOP

PLAY

REWIND ( ) /

FAST FORWARD ( )

(for TV)

POWER ON

STANDBY

(POWER OFF)

NUMERIC

CHANNEL

UP/DOWN()

VOLUME

UP/DOWN()

MUTE

INPUT

SELECTOR

(for satellite

receiver)

POWER ON

STANDBY

(POWER OFF)

NUMERIC

CHANNEL

UP/DOWN()

VOLUME

UP/DOWN()

MUTE

INPUT

SELECTOR

(for cable box)

POWER ON

STANDBY

(POWER OFF)

NUMERIC

CHANNEL

UP/DOWN()

VOLUME

UP/DOWN()

MUTE

INPUT

SELECTOR

RD-7503(A) 2008.11.4 1:45 PM 페이지 16

ENGLISH

17

LOADING BATTERIES

OPERATING COMPONENTS WITH REMOTE CONTROL

REMOTE CONTROL OPERATION RANGE

• Use the remote control within a range of about 7 meters

(23 feet) and angles of up to 30 degrees aiming at the

remote sensor.

• In such a case that some components do not have the

REMOTE SENSOR which receives the remote signals,

this remote control cannot operate them.

When the remote control does not operate, the old batteries should be replaced. In this case, load new batteries within several

minutes after removing old batteries.

If the batteries are removed or have been exhausted for a longer period of time, memorized contents will be cleared. Should

this happen, you should memorize them again.

• Remove the batteries when they are not used for a long

time.

• Do not use the rechargeable batteries (Ni-Cd type).

• Be sure to use alkaline batteries.

1. Enter the setup code for each component other

than this receiver. For details, refer to "Entering

a setup code" on page 18.

2. Turn on the component you want to operate.

1. Remove the cover.

2. Load two batteries ("AAA" size, 1.5V) matching

the polarity.

3. Press the DEVICE button on the remote control

corresponding to the component you wish to

operate.

4. Aim the remote control at the REMOTE

SENSOR of the component you wish to control

and press the button corresponding to the

operation you want.

RD-7503(A) 2008.11.4 1:45 PM 페이지 17

ENGLISH

5. Repeat the above steps 1 to 4 for each of your

components.

18

USING FUNCTIONS OF REMOTE CONTROL

Entering a setup code

• This remote control can control up to 6 different components.

• Before operating audio and video components other than this receiver with using this remote control, the setup code for each

component should be entered.

• For system remote control operation, "000" was stored previously in the memory of the device button "DOCK" for Sherwood iPod

dock, "DVD" for Sherwood DVD player and "TV" for Sherwood TV respectively as its factory setup code. So, you don’t need to

enter its code for each Sherwood component except in such a case that its code does not work.

• The SET LED will flicker once.

Note :

• The "AVR" button is unavailable for the audio

components other than this receiver.

1. Turn on the component you want to operate.

2. Find the setup codes according to the type and

the brand name of your component, referring to

"Setup Code Table" on page 62.

3. Press and hold down both the ENTER button

and the desired one of the DEVICE buttons for

more than 1 seconds.

4. Enter a 3 digit code, aiming the remote control

at the remote sensor on the component.

Example: When entering "001".

• If entering is performed successfully, the SET LED will

flicker twice.

• To be sure that the setup code is correct, press the

POWER ON (or STANDBY) button. If your component

is turned off, the setup code is correct.

• When your component is not turned off, repeat the

above steps 2 to 4, trying each code for your

component until you find one that works.

Notes:

• If the SET LED did not flicker twice, then repeat the

above steps 3 to 4 and try entering the same code

again.

• Manufacturers may use different setup codes for the

same product category. For that reason, it is important

that you check to see if the code you have entered

operates as many controls as possible. If only a few

functions operate, check to see if another code will work

with more buttons.

RD-7503(A) 2008.11.4 1:45 PM 페이지 18

ENGLISH

19

• If removing all punch-through functions is performed

successfully, the LED will flicker twice.

Using a punch-through function

This remote control may be programmed to operate either

the AUDIO volume punch-through or the TV volume and/or

TV channel punch-through in conjunction with any of the

six components controlled by this remote control.

For example, since this receiver will likely be used as the

sound system while watching TV, you may want to adjust

this receiver’s volume although this remote control is set to

control the TV.

• When programming this remote control for the AUDIO

volume punch-through, press and hold down both "AVR"

button and "VOLUME " button for more than 1 second.

• If programming is performed successfully, the SET LED

will flicker twice.

•

When you want either TV volume or TV channel

punch-through, press and hold down both "TV" button

and either "VOLUME



" or "CHANNEL



" button for

more than 1 second.

Note :

• If you use one of AUDIO and TV volume punch-

through functions, you cannot use the other.



Removing a punch-through function

• When removing the AUDIO volume punch-through,

press and hold down both "AVR" button and

"VOLUME " button for more than 1 second.

• If removing is performed successfully, the SET LED will

flicker twice.

•

When you want to remove either TV volume or TV

channel punch-through, press and hold down both "TV"

button and either "VOLUME



" or "CHANNEL



"

button for more than 1 second.



Removing all punch-through functions

Press and hold down both "AVR" button and "AUDIO

ASSIGN" button for more than 1 second.

RD-7503(A) 2008.11.4 1:45 PM 페이지 19

ENGLISH

20

Programming a macro function

• The macro function enables you to program a

series of button operations(up to 10) on this

remote control into a single button.

• You can store up to three separate macro

command sequences into "M1", "M2" and "M3"

buttons.

• If the macro mode is entered, the SET LED will

flicker once.

Example: When programming a series of button

operations into "M1" button.

1. Press and hold down both "ENTER" button and

one of three NUMERIC buttons ("1" ~ "3")

corresponding to "M1"~"M3" buttons for more

than 1 second.

Note :

You should press the corresponding DEVICE

buttons before pressing each operation button.

Example: When playing a DVD on the DVD

player connected to VIDEO 3 jacks of

this receiver.

. Press "AVR" button to control this receiver.

. Press "POWER ON" button to turn this

receiver on.

. Press "AVR" button to control this receiver.

. Press "VIDEO 3(8)" button to select the

desired input source.

. Press "DVD" button to control the DVD player.

. Press "POWER ON" button to turn the DVD

player on.

. Press "DVD" button to control the DVD player.

. Press "" button to start playback.

2. Press the operation buttons you want to

program in order.

3. Press "ENTER" button.

• If the programming is performed successfully, the

SET LED will flicker twice.

�To remove a macro program

• When removing a macro program, perform the

above steps 1 and 3, but ignore the step 2.

�To change a macro program

• When a new macro program is stored into a

MACRO button with performing the above steps

1 to 3, the previous macro program is cleared

from the memory of the MACRO button.

Operating a macro function

Notes:

• The codes programmed into a MACRO button will be

transmitted at an interval of 0.5 seconds. However,

some components may not be able to complete one

operation in 0.5 seconds and may miss the next code.

In this case, the macro function cannot control the

corresponding components correctly.

• Be sure to use the remote control within the remote

control operation range of the components.

• Depending on the operation status of the components,

etc., the macro function cannot control the

corresponding components correctly.

• Aim the remote control at the REMOTE SENSORs of

the components to be controlled and press the MACRO

button you want.

Example: When pressing "M1" button.

RD-7503(A) 2008.11.4 1:45 PM 페이지 20

Page is loading ...

Sherwood RD-7503 User manual

Sherwood RD-7503 User manual

Related papers

Other documents