InSinkErator Hot1 User manual

Page is loading ...

Wing Nut Mounting Nut

Rubber Gasket

Brass Nut

Ferrule

3

HOW TO USE THIS INSTRUCTION MANUAL

Provides a step-by-step narrative describing the installation step, with check boxes that

can be marked as you progress through the installation.

Contains simple illustrations that provide visual instruction to support the narrative.

CAUTIONS, WARNINGS and DANGERS that will require your attention during the step.

These instructions are separated into main sections, indicated by numbers, and subsections,

indicated by capital letters. The manual is setup this way to allow you to take a break at any

point after completing a section or subsection without affecting the installation process.

What you’ll see in the

instruction manual:

1

2

3

Valve

Lever

B

■

Press valve lever down for about 20

seconds until water freely runs out of

the spout. Hold valve open at lease 60

seconds to let the water run to flush

out the lines.

Water will be cold since tank has not

been plugged in yet.

Property Damage: Do not connect electric power until

tank is filled with water. Failure to do so my damage heating

element or thermal safety fuse and will void the warranty.

1

2

An imminently hazardous situation, which, if not avoided, will result in death or serious injury.

A potentially hazardous situation, which, if not avoided, could result in death or serious injury.

A potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

3

Equipment You May Need:

nn

For your satisfaction and safety, read all instructions, cautions, warnings and dangers before installing

or using this instant hot water dispenser.

nn

This particular unit is not intended for commercial use.

nn

Make sure that all electrical wiring and connections conform to local codes.

nn

A standard 115-volt grounded electrical outlet is required under the sink for the dispenser’s electrical power.

nn

The wall outlet powering your dispenser must have power supplied to it continuously.

nn

This outlet must be fused and should not be controlled by the same wall switch that operates the

disposer, unless you have a SinkTop Switch

™

from InSinkErator

®

.

nn

Moving parts inside the tank causing a rattling noise is normal.

nn

This unit does not contain a drain plug and should not be installed where periodic draining is required,

such as summer homes.

WHAT YOU SHOULD KNOW BEFORE YOU BEGIN

Equipment Required:

n Compression fitting,

T-fitting or saddle valve

n Adjustable wrench

n Phillips and flat blade screwdrivers

n Pencil

n Tape Measure

nn

Hole punch

nn

Hole saw

nn

Basin wrench

nn

Drill

nn

Level

If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench and

a 1/8" plug or a 1/4" cap (

not supplied) for the faucet spray hose line. See Step 1-B.

If you need to cut a mounting hole in your stainless steel sink, you may need a 1

1

⁄4" - 1

1

⁄2" hole saw

made for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a surface

other than stainless steel.

WHAT YOU NEED TO GET STARTED

2

COMPONENTS IN THIS PACKAGE

A 115-volt grounded

outlet within 30 inches

of the dispenser is

required to provide

power to the tank.

A minimum of

3

⁄4" of space

is required

between the

center of the

dispenser head

and splashboard/

wall in order for

the appliance to

operate properly.

Note: The wall outlet for your

dispenser must have power

supplied to it continuously and

must be fused. It should not be

controlled by the same wall switch

that operates your disposer.

Spout

Spout Holder

Maximum

Countertop

Thickness

for Mounting

3 Wire

Power Cord

30" Long

(76cm)

Slotted

Set Screw

(Opposite Side)

Valve

Lever

Rubber

Gasket

Mounting

Nut

Wing

Nut

¼" Copper Tube

16" Long

(40.6cm)

Cold Water Line

Width of

Unit 5¼"

(13.3cm)

6"

(15.2cm)

2"

(5.1cm)

3"

(7.6cm)

11¾"

(28.9cm)

4"

(10.2cm)

2½"

(6.4cm)

8

2¼ "

(6.5cm)

9

16

The wall outlet for your dispenser must have power supplied to it continuously

and must be fused. It should not be controlled by the same wall switch

that operates your disposer.

PREPARATION

START HERE

nn

Identify location for the dispenser.

nn

Check to make sure there is proper

clearance for dispenser handle to be

fully opened.

nn

Check to make sure counter is not

too thick.

nn

Make sure there is a grounded

electrical outlet under the sink.

nn

Turn off water supply.

nn

If using the sink sprayer hose hole,

remove nut that connects sprayer

hose at bottom of faucet.

nn

Using adjustable wrench, remove

nut connecting sprayer washer

flange in sprayer hole.

nn

Plug hose opening with either a 1/8"

plug or a 1/4" cap

(not supplied).

1

A

B

Consult a professional before drilling into

a surface other than stainless steel.

C

What if you don’t have a sprayer hole or

don’t want to use it?

nn

Many homeowners replace the soap

dispenser in their sink with an instant

hot water dispenser.

nn

If drilling a hole into a stainless steel

sink or counter top, you can cut a

mounting hole for the dispenser with a

hole saw for stainless steel, or you can

use a hole punch.

Required Hole Diameter

1

3

⁄8"

1

2

3

Bra

ss Nut

Ferru

le

Brass Insert

Wing Nut

Plug

Fiber

Washer

Brass Nut

Ferrule

Wing Nut

Fiber

Washer

1

2

3

Brass Nut

Ferrule

Brass Insert

Wing Nut

Plug

Fiber

Washer

Brass Nut

Ferrule

Wing

Nut

Fiber

Washer

Required minimum from

center of hole to wall

Maximum counter

thickness (depth)

3

⁄4"

2"

DIMENSIONS

4

5

If you have to drill through sink or

countertop, you may need to rent or

purchase the appropriate tools.

T-fitting

1/4" Diameter

Tube

Cold Water

Supply Line

Mounting

Nut

Rubber

Gasket

Wing

Nut

Spout

Rubber

Seal

Mounting

Nut

Rubber

Gasket

Wing

Nut

Spout

Rubber

Seal

T-fitting

1/4" Diameter

Tube

Cold Water

Supply Line

6

Compression valve or T-fitting option

(not supplied):

nn

Ensure that a shutoff valve is installed

on the cold water supply line. If so, a

T-fitting or compression valve can be

used to connect the dispenser.

nn

Connect the 16" (40.6 cm) long, 1/4"

diameter copper tube on the

dispenser to the T-fitting as shown

(see step 4).

3

WATER CONNECTION OPTIONS

Attach the valve to a

cold water supply line

.

Shutoff valve option (not supplied):

nn

The water connection can be made

using a shutoff valve. This is a more

complex installation and should only

be attempted by an experienced

installer with the proper knowledge

and tools.

Saddle valve option (not supplied):

nn

Follow the directions for

“self-piercing attachment”

included with the valve.

nn

Connect the 16" (40.6 cm) long, 1/4"

diameter copper tube on the dispenser

to the saddle valve as shown (see step 4).

nn

Open the valve and let a small amount

of water run through it into a pan.

This will flush the line of sediment.

nn

2

nn

Remove the spout by loosening

the set screw in spout holder

approximately 2 full turns and

pull out spout.

nn

Mount the unit through the 1 3/8"

diameter (35 mm) hole in the sink.

Make sure the valve lever is in the

up position and feed the spout end

of the dispenser through the sink

mounting hole.

A

C

INSTALLING THE DISPENSER

nn

While holding the dispenser in

place with spout removed, slip

the rubber gasket and mounting

nut over the valve lever and

hand tighten the nut on the

threaded barrel.

B

nn

Align spout so water runs into the

sink and secure the dispenser by

tightening the wing nut from the

underside of the sink.

B

Personal Injury: Failure to tighten set screw allows easy

removal of spout. Operation of unit with spout removed

could cause injury from hot water spray.

Mounting

Nut

Rubber

Gasket

Wing

Nut

Spout

Rubber

Seal

7

D

nn

Reassemble the spout ensuring

the rubber seal is in place on inner

spout tube grove before re-inserting

spout into tank outlet.

nn

If rubber seal is not on spout, check

inside tank outlet. Remove and

install seal per diagram.

nn

Push spout into dispenser as far as

it will go and tighten set screw.

Mounting

Nut

Rubber

Gasket

Wing

Nut

Spout

Rubber

Seal

Saddle valves are susceptible

to clogging

.

The dispenser must be mounted in

the upright (vertical) position only.

T-fitting

1/4" Diameter

Tube

Cold Water

Supply Line

Ferrule

Nut

Spout and spout holder should not be loose

after mounting. First tighten mounting nut

and then tighten wing nut securely.

Valve

Lever

Valve

Lever

8

A

5

nn

First, open the shutoff valve all the

way and see if your connections are

watertight. If there are any leaks

carefully re-tighten all connections.

FILL THE TANK & CONNECT POWER

C

B

nn

Check all connections to ensure they

are tight and that there are no leaks,

then plug in instant hot water tank.

nn

Allow 10-15 minutes for water to reach

target temperature. Gurgling or hissing is

normal during the initial heating cycle.

Steam and/or hot water coming from the

spout without pressing down on the handle

is also normal. If steam is still emitted after

setup, thermostat adjustments may be

needed (pg. 11).

nn

Press valve lever down for about 20

seconds until water freely runs out of

the spout. Hold valve open at least 60

seconds to let the water run to flush

out the lines.

nn

Water will be cold since tank has not

been plugged in yet.

Valve

Lever

Valve

Lever

Valve

Lever

Valve

Lever

A

4

nn

Bend and position the 1/4" copper

line from the dispenser so it fits into

the cold water supply. With one hand,

support the copper line coming out

of the tank and bend the tube with

the other hand.

nn

Do not kink. Bend tube carefully.

CONNECTING WATER TO DISPENSER

C

B

nn

Push the tube end all the way into

the T-fitting or valve. Hold the tube

end in position and push the ferrule

down as far as it will go. Then,

tighten the nut over the ferrule with

your fingers. Make sure the tube

end is going straight into the hole.

Then tighten the nut firmly with a

1/2" wrench.

nn

When connecting to a compression

type T-fitting or valve, remove the

nut and ferrule (round brass piece)

from the fitting. Then, place the nut

followed by the ferrule over the end

of the tube coming from the

dispenser

.

Ferrule

Nut

Ferrule

Nut

Ferrule

Nut

9

Property Damage: Do not remove or alter the thermal

safety fuse. If you suspect the thermal fuse is open,

contact your Authorized Service Center.

Property Damage: Do not connect electric power until tank

is filled with water. Failure to do so may damage heating

element or thermal safety fuse and will void the warranty.

Property Damage: Make sure the bends in tubing are

smooth and not kinked. Don’t use paste-type sealants on

water line connections. Tighten compression fittings

snug but don’t over tighten.

Property Damage: Never place a restriction on the delivery

of water from the spout. Such a restriction prevents draining

the expansion chamber and could damage the tank.

10

Scalding Hazard: Do not allow

water to boil. May result in

severe burns.

Factory temperature

pre-set is 190

˚F.

nn

Disconnect power

from unit.

nn

To adjust water

temperature you’ll

need to access the panel on the front of

the tank. Using a screwdriver, turn

thermostat screw clockwise to increase

temperature or turn counter clockwise to

decrease temperature. The cover must

always be in place for the thermostate to

respond properly.

nn

After adjusting, depress the dispenser

handle for 20 seconds for the water to

re-heat to the new setting. If temperature

still is not to your liking, repeat the procedure

making sure that the handle is depressed

for 20 seconds.

nn

Regularly inspect the unit for any signs of

leakage. If there are signs of water damage,

immediately remove the unit from service.

nn

To avoid water damage from leakage,

replace all cut, loose or split tubing

.

nn

A drain pan, plumbed to an appropriate

drain or outfitted with a leak detector,

should be used in those applications where

any leakage could cause property damage.

PROPERTY DAMAGE

CARE AND USE

ADJUSTING THE THERMOSTAT

nn

Only use mild cleaners to clean the faucet

and plastic components.

nn

Cleaners with acids, abrasives, alkaline

or organic solvents will result in deterioration

of the plastic components and void

the warranty.

CLEANING THE FAUCET AND TANK

Anytime the instant hot water dispenser is not used

for extended periods of time, unplug and drain unit.

If it is below freezing you will need to unplug the

unit and drain it.

nn

Disconnect power from unit.

nn

Push hot water dispenser faucet lever

and allow water to flow until it is cool.

nn

Shut the cold water flow off at the

shut off valve.

nn

Remove unit from sink and turn upside

down to drain.

SEASONAL STORAGE/DRAINAGE

11

Property Damage: To avoid water damage, replace any loose or split tubing.

Periodically inspect the unit for any signs of leakage and immediately remove from

service any unit suspected of leaking.

Personal Injury: This tank is a non-pressurized tank. DO NOT modify this system.

DO NOT close vent tube or connect other type dispensers or valves to the tank. Use only

the InSinkErator dispenser faucet supplied. Use only parts provided. Contact an

authorized InSinkErator Service agent for repairs or replacement components.

Electric Shock Hazard: Using an ungrounded or improperly connected appliance can

result in serious injury or death from electrical shock.

1-Year Warranty

Covers all replacement parts and labor to correct defects in material or workmanship in the

dispenser system, for the full warranty period from the date of installation in your home. If

warranty service is required during the warranty period, contact an authorized InSinkErator

service agent to replace or repair the unit in your home at no cost to you. If your dispenser is

replaced rather than repaired, the warranty on the new unit shall be for the duration of the

remaining portion of the original dispenser’s warranty.

Note: Warranty is determined by unit

serial number and/or date of installation. Purchase or installation receipt may be required to

verify warranty status. When service is required, and for the location of your nearest factory

authorized service center, call toll free 1-800-558-5700.

The foregoing warranty does not apply to damage or inoperation resulting from accident,

alteration, misuse, abuse, improper installation, installation not in accordance with these

instructions or local electrical and/or plumbing codes. We do not assume any responsibility for

consequential damage. Install using genuine InSinkErator

®

manufactured components only.

Use of non InSinkErator components will void your warranty.

Some states do not allow limitations on how long an implied warranty lasts, or the

exclusion or limitations of incidental or consequential damages, so the above limitations or

exclusion may not apply to you. This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This appliance must be grounded. This instant hot water dispenser is equipped with a cord that

has a grounding conductor and a grounding pin. The plug must be connected to an appropriate

outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet

installed by a qualified electrician. Check with a qualified electrician or serviceman if you are in

doubt as to whether the instant hot water dispenser is properly grounded.

WARRANTY INFORMATION

Fire Hazard: To minimize possibility of fire, DO NOT store flammable items such as

rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other

flammable vapors and liquids in the vicinity of this or any other appliance.

An instant hot water dispenser, like any water heater, has a limited life and will eventually

fail. To avoid possible property damage, this instant hot water dispenser should be

regularly examined for leakage and replaced when necessary. A drain pan, plumbed to an

appropriate drain or outfitted with a leak detector, should be used in those applications

where any leakage could cause property damage.

Electric Shock Hazard: To prevent electrical shock,

disconnect power before servicing unit. Use only a

properly grounded and polarized electric outlet.

Surtidor de agua caliente al instante

Manual de propietario

Modelo Hot1

Installation, Care & Use

Instalación, Cuidado & Uso

Installation, entretien

et mode d’emploi

If you are still experiencing trouble call the AnswerLine

™

1-800-558-5700.

TROUBLESHOOTING

WHAT TO DO

Water and steam spits

forcefully from spout

without turning on the

dispenser faucet.

Water is not hot

• Unit is boiling.

May be normal during initial setup.

• The unit is unplugged.

• The electric outlet is inoperative.

•

Depress faucet lever to release some water from

the tank.

• Adjust water temperature using dial on tank front.

Remember that at higher altitudes, water boils

at lower temperatures.

•

Make sure the unit is connected to a properly grounded

electric outlet.

• Make sure the circuit breaker fuse is functioning properly.

• Check that the outlet is not switched off.

Water is too hot

or not hot enough

• Thermostat is not adjusted to

your needs.

•

Adjust the thermostat slowly, then depress or twist faucet handle

for 20 seconds to bring in fresh water to be heated at the new

setting. Allow 5-7 minutes for water to reach new temperature.

Water is dripping from

the spout/vent

intermittently

• The expansion chamber isn’t draining

properly due to low water pressure.

• The spout is blocked.

• Unplug the unit. If the dripping doesn’t stop after a few

minutes, check the supply valve to ensure that is fully

open and there are no obstructions in the water line

reducing the pressure below 30 psi (

i.e., a poorly mounted

saddle valve, a clogged water filter, or a partially opened

shut-off valve).

•

Unscrew spout end piece and clean out any debris.

Water is dripping

from the spout/vent

constantly

• Debris in the water line may be

in the faucet valve seat causing a

slow water leak.

•

Unscrew spout end piece and clean out any debris.

•

Depress lever 7-10 times to flush faucet & lines.

Divided stream

• Debris in the end piece. •

Unscrew spout end piece and clean out any debris.

PROBLEM POSSIBLE CAUSE

Please read Troubleshooting Guide and/or visit

www.insinkerator.com before calling AnswerLine

™

12

Page is loading ...

InSinkErator Hot1 User manual

InSinkErator Hot1 User manual

in other languages

Related papers

Other documents