Worksaver MCR-7 User manual

Brand: Worksaver

Model: MCR-7

Type: User manual

SAFETY PRECAUTIONS

MOST ACCIDENTS OCCUR BECAUSE OF NEGLECT OR CARELESSNESS.

AVOID NEEDLESS ACCIDENTS BY FOLLOWING ALL OF THE SAFETY PRECAUTIONS LISTED BELOW.

• Machinery should be operated only by those who are

responsible and are authorized to do so.

• Stop the engine, lower all equipment, lock the brakes,

and remove the ignition key before dismounting from the

tractor.

• Never stand between tractor and implement while tractor

is being backed to hitch.

• Loose fitting clothing should not be worn, to avoid catch-

ing on various parts.

• Detach implement in area where children normally do not

play.

• When performing adjustments or maintenance on an

implement, first lower it to the ground or block it securely

at a workable height.

• Only a qualified operator should be permitted on tractor

when in operation; no riders allowed.

• Make certain everyone is in the clear before starting

tractor or raising or lowering equipment.

• Operate the tractor and implement only while seated in

the driver’s seat.

•

Reduce speed when transporting mounted implements

to avoid bouncing and momentary loss of steering

control.

• A heavy load can cause instability of the tractor. Use

extreme care during road travel. Slow down on turns and

watch out for bumps. Tractor may need front counter-

weights to counter-balance the weight of the implement.

• Reduce speed on hillsides or curves so there is no

danger of tipping.

• Avoid driving too close to the edge of ditches or creeks.

• Do not transport implement on public roads without

reflectors and slow moving vehicle emblem in daylight

and with approved warning lights at night and other

periods of poor visibility.

• Due to the width of some implements, use extra caution

on highways, farm roads, and when approaching gates.

• Always be sure the implement is in the proper position for

transport.

• Keep alert and watch the front as well as the rear when

working with the implement.

OWNER’S/

OPERATOR’S

MANUAL

MODEL NO.’s

DCR-4 MCR-6

DCR-5 MCR-7

LRHD-6

LRHD-7

LRHD-8

CAUTION

For Safe Operation

Read Rules And

Instructions Carefully

SINO LEEINGLES, PIDA AYUDA

A AIGUIEN QUE SI LO LEA

PARA QUE LE TRADUZCA LAS

MEDIDAS DE SEGURIDAD.

CAUTION

THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD

BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE

1. Select an area for assembly that is clean and free of any

debris which might cause persons working on the

assembly to trip.

2. Do not lift heavy parts or assemblies. Use crane, jack,

tackle, fork trucks or other mechanical devices.

3. Preview the assembly instructions in your operator’s

manual before proceeding further.

4. If the assembly instructions call for parts or assemblies to

be blocked up, use only blocking material that is in good

condition and is capable of handling the weight of the

assembly to be blocked. Also insure that the blocking

material is on a clean, dry surface.

5. Never put hands, or any part of body, under blocked up

assemblies if at all possible.

6. After completing assembly, thoroughly inspect the

machine to be sure that all nuts, bolts, hydraulic fittings

or any other fastened assemblies have been thoroughly

tightened.

7. Before operating the machine, thoroughly read the

operation section of your operator’s manual.

8. Before operating, read the maintenance section of your

operator’s manual to be sure that any parts requiring

lubrication, such as gearboxes, are full, to avoid any

possible damage.

9. Before operating equipment – If you have any

questions regarding the proper assembly or

operation, contact your dealer or representative.

OWNER’S/

OPERATOR’S

MANUAL

MODEL NO.’s

DCR-4 MCR-6

DCR-5 MCR-7

LRHD-6

LRHD-7

LRHD-8

MARCH 2006

WS-LE003-OG

MAKE EVERY DAY

A HOLIDAY FROM ACCIDENTS

WORKSAVER, INC.

P.O. BOX 100 LITCHFIELD, IL 62056-0100 (217) 324-5973

WEB: http://www.worksaver.com E-MAIL: sales@worksaver.com

3 PT. LANDSCAPE RAKE

Safety Instructions Assembly & Mounting

Tractor Preparation Maintenance

Operating Instructions Repair Parts

3 PT. LANDSCAPE RAKE

DCR Series – Cat. 0/I – up to 25 hp

MCR Series – Cat. I – up to 40 hp

LRHD Series – Cat. I – up to 50 hp

WHEN ORDERING REPAIR PARTS,

ALWAYS GIVE THE FOLLOWING INFORMATION:

1. PART NUMBER

2. PART DESCRIPTION

3. MODEL NUMBER

4. NAME OF ITEM

DCR-4

LRHD-7

(Rakes shown with optional gauge wheels)

TABLE OF CONTENTS

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SAFETY SIGNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . 7

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 9

SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

TROUBLE-SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

PARTS DRAWINGS & LISTS . . . . . . . . . . . . . . . . . . . . . . . 12-14

TO THE OWNER:

Read this manual before using your Landscape Rake. This manual is provided to give you the necessary

operating and maintenance instructions for keeping your Landscape Rake in top operating condition.Please read

this manual thoroughly. Understand what each control is for and how to use it. Observe all safety signs on the

machine and noted throughout the manual for safe operation of implement. Keep this manual handy for ready

reference.

Like all mechanical products, it will require cleaning and upkeep.

Use only genuine Worksaver, Inc. service parts. Substitute parts will void the warranty and may not meet

standards required for safe and satisfactory operation. Record the model and serial number of your Landscape

Rake here:

Model:________________________________________ Serial Number:_______________________________

RETAIL CUSTOMER’S RESPONSIBILITY

It is the Retail Customer and/or Operator’s responsibility to read the Operator’s Manual, to operate,

lubricate, maintain, and store the product in accordance with all instructions and safety procedures.

Failure of the operator to read the Operator’s Manual is a misuse of this equipment.

It is the Retail Customer and/or Operator’s responsibility to inspect the product and to have any part(s)

repaired or replaced when continued operation would cause damage or excessive wear to other parts or

cause a safety hazard.

It is the Retail Customer’s responsibility to deliver the product to the authorized Worksaver Dealer, from

whom he purchased it, for service or replacement of defective parts which are covered by warranty.

Repairs to be submitted for warranty consideration must be made within forty-five (45) days of failure.

It is the Retail Customer’s responsibility for any cost incurred by the Dealer for traveling to or hauling

of the product for the purpose of performing a warranty obligation or inspection.

SINO LEEINGLES, PIDA AYUDA A

AIGUIEN QUE SI LO LEA PARA QUE

LE TRADUZCA LAS MEDIDAS DE

SEGURIDAD.

STATEMENT

OF POLICY

It is the policy of Worksaver,

Inc.to improve its products where

it is possible and practical to do

so. Worksaver, Inc. reserves the

right to make changes or

improvements in design and con-

struction at any time, without

incurring the obligation to make

these changes on previously

manufactured units.

LRHD

LANDSCAPE RAKE

PARTS LIST

DGW-20 GAUGE WHEEL PARTS LIST

(OPTIONAL)

LIMITED WARRANTY

✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯

Worksaver warrants to the original purchaser of any new 3 Pt. Landscape Rake, that the equipment be free

from defects in material and workmanship for a period of six (6) months for non-commercial, state, and

municipalities. Use sixty (60) days for commercial use from date of retail sale.

Replacement or repair parts installed in the equipment covered by this warranty are warranted for ninety (90)

days from the date of purchase of such part or to the expiration of the applicable new equipment warranty

period, whichever occurs later.

Such parts shall be provided at no cost to the user during regular working hours. Worksaver reserves the right

to inspect any equipment or parts which are claimed to have been defective in material or workmanship.

DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES

Worksaver’s obligation under this warranty, to the extent allowed by law, is in lieu of all warranties, implied or

expressed, including implied warranties of merchantability and fitness for a particular purpose and any liabili-

ty for incidental and consequential damages with respect to the sale or use of the items warranted. Such

incidental and consequential damages shall include but not be limited to: transportation charges other than

normal freight charges; cost of installation other than cost approved by Worksaver;duty; taxes;charges for nor-

mal service or adjustments; loss of crops or any other loss of income; rental of substitute equipment, expens-

es due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond the

control of Worksaver.

THIS WARRANTY SHALL NOT APPLY:

1. To vendor items which carry their own warranties, such as hydraulic motors, tires, and tubes.

2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.

3. If parts not made or supplied by Worksaver have been used in connection with the unit, if, in sole judge-

ment of Worksaver such use affects its performance, stability, or reliability.

4. If the unit has been altered or repaired outside of an authorized Worksaver dealership in a manner which,

in the sole judgement of Worksaver affects its performance, stability or reliability.

5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid,

worn tines, or to normal deterioration of such things as belts and exterior finish, due to use or exposure.

6. To expendable or wear items such as tines, chains, sprockets, belts, springs and other items that in the

company’s sole judgement is a wear item.

NO EMPLOYEE OR REPRESENTATIVE OF WORKSAVER IS AUTHORIZED TO CHANGE THIS

WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN

WRITING AND SIGNED BY WORKSAVER’S SERVICE MANAGER, POST OFFICE BOX 100, LITCHFIELD,

ILLINOIS 62056-0100.

✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯ ✯

MCR LANDSCAPE RAKE PARTS LIST

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous.There is no substitute for a cautious, safe-minded opera-

tor who recognizes the potential hazards and follows reasonable safety practices.The manufacturer has designed this

implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!!

Read the safety messages on the implement and shown in your manual.

Observe the rules of safety and common sense!

THIS SAFETY ALERT SYMBOL IDENTIFIES IMPORTANT

SAFETY WARNING MESSAGES. CAREFULLY READ EACH

WARNING MESSAGE THAT FOLLOWS. FAILURE TO

UNDERSTAND AND OBEY A SAFETY WARNING, OR

RECOGNIZE A SAFETY HAZARD, COULD RESULT IN AN

INJURY OR DEATH TO YOU OR OTHERS AROUND YOU.

THE OPERATOR IS ULTIMATELY RESPONSIBLE FOR THE

SAFETY OF HIMSELF, AS WELL AS OTHERS, IN THE

OPERATING AREA OF THE TRACTOR AND ATTACHED

EQUIPMENT.

IMPORTANT SAFETY INFORMATION!

Working with unfamiliar equipment can lead to careless injuries. Read this manual, and the manual for your tractor,

before assembly or operating, to acquaint yourself with the machines. It is the implement owner’s responsibility, if this

machine is used by any person other than yourself, is loaned or rented, to make certain that the operator, prior to

operating:

1. Reads and understands the operator’s manuals.

2. Is instructed in safe and proper use.

The use of this equipment is subject to certain hazards which cannot be protected against by mechanical

means or product design. All operators of this equipment must read and understand this entire manual, pay-

ing particular attention to safety and operating instructions, prior to using. If there is something in this manual

you do not understand, ask your supervisor, or your dealer, to explain it to you.

THIS SYMBOL MEANS

– ATTENTION!

– BECOME ALERT!

– YOUR SAFETY IS INVOLVED!

UNDERSTAND SIGNAL WORDS

Note the use of the signal words DANGER, WARNING

and CAUTION with the safety messages. The

appropriate signal word for each has been selected

using the following guidelines:

DANGER: Indicates an imminently hazardous situation

that, if not avoided, will result in death or serious injury.

This signal word is to be limited to the most extreme

situations typically for machine components which, for

functional purposes, cannot be guarded.

If you have questions not answered in this manual or require additional copies or the manual is damaged, please

contact your dealer or the manufacturer directly.

WARNING: Indicates a potentially hazardous sit-

uation that, if not avoided, could result in death

or serious injury, and includes hazards that are

exposed when guards are removed. It may also

be used to alert against unsafe practices.

CAUTION: Indicates a potentially hazardous sit-

uation that, if not avoided, may result in minor or

moderate injury. It may also be used to alert

against unsafe practices.

DCR LANDSCAPE RAKE

PARTS LIST

SGW-10 GAUGE WHEEL PARTS LIST

(OPTIONAL)

SAFETY INSTRUCTIONS (continued)

All equipment is potentially hazardous. There is no substitute for a cautious, safe-minded operator who

recognizes potential hazards and follows reasonable safety practices.

This equipment is dangerous to children and persons unfamiliar with its operation. The operator should be a

responsible adult familiar with farm machinery and trained in this equipment’s operations. Do not allow per-

sons to operate or assemble this unit until they have read this manual and have developed a thorough

understanding of the safety precautions and of how it works.

Only use a power unit equipped with a ROPS cab or rollover protective structure. Keep foldable ROPS sys-

tems in “locked up” position at all times. Keep seat belt fastened.

Always use two people to handle heavy, unwieldy components during assembly, installation, removal, or

moving the implement.

Never place any part of your body where it would be in danger if movement should occur during assembly,

installation, operation, maintaining, repairing, removal, or moving the implement.

Never place yourself between the tractor and implement while implement is in operation.

Do not work under a raised implement unless it is securely blocked or held in position. Do not depend on the

tractor hydraulic system to hold the implement in place.

A heavy load can cause instability of the tractor. Use extreme care during travel. Slow down on turns and

watch out for bumps. The tractor may need front counter-weights to counter-balance the weight of the

implement.

Never use alcoholic beverages or drugs which can hinder alertness or coordination while operating this

equipment. Consult your doctor about operating this machine while taking prescription medications.

Do not allow others to ride on the tractor with an operator. Riders are subject to injury such as being struck by

foreign objects or being thrown off. Riders obstruct the operator’s view resulting in unsafe operation. Never

allow anyone to ride on the implement!

Before you operate the implement, check over all pins, bolts and connections to be sure all are securely in

place. Replace any damaged or worn parts immediately.

Most accidents occur because of neglect or carelessness. Keep all helpers and bystanders fifty feet (50’) from

an operating power unit and attached equipment. Only properly trained people should operate this machine.

It is recommended the tractor be equipped with a Rollover Protection System (ROPS) and a seat belt that is

used. Always stop the tractor, set brake, shut off the engine, remove the ignition key, and lower loader and

attachment to the ground before dismounting. Never leave equipment unattended with the engine running.

TROUBLE-SHOOTING GUIDE

PROBLEM POSSIBLE CAUSE POSSIBLE REMEDY

Rake will not pene-

trate soil.

1. Tinebar set too straight.

2. Soil too hard.

Increase 3 pt. hitch toplink length.

Loosen soil with scarifiers or disk.

Wait for rain.

Rake teeth digging

in too much.

1. Tinebar pitch excessive.

2. Soft ground.

Adjust toplink (shorten).

Install gauge wheels.

Wait for dryer soil.

3 Pt. hitch frame

bent.

1. Hitting hidden objects in backfill

position or ramming backwards into

hard piles of soil.

2. Using too large of tractor.

Use slow speed when in unknown soil

conditions.

Always backfill at slow speed.

Preferably use tractor of recommended

horsepower.

Slow down and use extra care.

Unable to hold level

grade.

1. Tractor draft control lifting blade.

2. Soil too hard.

3. Uneven ground.

Set tractor draft control.

Loosen soil with scarifiers or disk.

Install gauge wheels.

Bent tinebar or bent

teeth.

1. Hitting hidden objects.

2. Using too large of tractor or one that

is heavily weighted and has four

wheel drive.

3. Hitting end of tinebar on stumps,

concrete curb, or corner of building.

Know soil conditions. Use slow speed

when soil conditions unknown.

Preferably use tractor of recommended

horsepower.

Slow down and use extra care.

Have operator use care when driving

close to obstacles.

SAFETY INSTRUCTIONS (continued)

Never allow children to operate or be around equipment.

Use stabilizer bars, adjustable sway chains, or sway blocks on your tractor lift arms to keep the implement from

swinging side to side. Adjust as tightly as practical for best performance.

Keep alert and watch the front as well as the rear when working with the implement.

When maneuvering close to buildings or passing through narrow areas, be sure to allow sufficient clearance

for the implement.

Do not operate close to ditches or creeks. Slow down when operating over rough ground.

Always be sure the implement is in the fully raised position when in transport.

When removing, changing the angle, or reversing the rake, be sure that your feet are never under the rake.

Use extreme caution when backfilling deep holes or trenches.

Be careful to avoid catching the rake on stumps or other immovable objects.

Use care when working on slopes.

Avoid excessive speed during operation.

Make adjustments only when the implement is attached to the tractor.

When using the rake in a reverse position, use extra care. Do not ram rake into piles of dirt. Tractor lift arms

and the rake are not built to take high impact loads in this position. Ramming backwards can also dislodge

operator from seat and/or tractor controls, resulting in possible serious injury or death.

Always ease the tractor into the load. It may be necessary to reposition and take less “bite” on the material to

move it safely.

Operating spring steel rake tines may suddenly fling rocks and clods. Keep all bystanders 50 feet away and

operator must wear safety glasses.

Stop power unit and equipment immediately upon striking an obstruction.Turn off engine, remove key, inspect,

and repair any damage before resuming operation.

Before leaving operator’s seat, lower lift arms and put attachment on the ground. Engage brake, stop engine,

remove key, and remove seat belt.

Never perform service or maintenance with engine running.

Watch for and avoid hidden obstructions, i.e., buried pipes, rocks, concrete piers, uneven concrete slabs,

stumps, etc., when operating.

OWNER SERVICE

TRANSPORTING

——————————————————

Pay particular close attention to the Safety Messages

regarding transport. Avoid unnecessary injuries and

equipment damage by exercising cautious, conscientious

travel procedures.

Attaching the landscape rake to the tractor increases

the overall length of the working unit. Allow additional

clearance for the landscape rake to swing when turning.

Always place the rake straight across (90° to line of

travel) for transport.

Raise the landscape rake as high as possible for trans-

porting.

MAINTENANCE

——————————————————

The information in this section is written for operators

who possess basic mechanical skills. If you need help,

your dealer has trained service technicians available. For

your protection, read and follow the safety information in

this manual.

Inspect the landscape rake for loose, damaged or worn

parts and adjust or replace if needed.

Repaint parts where paint is worn or scratched to pre-

vent rust.

Check all bolts and nuts to be sure they are tight.

Periodically grease the gauge wheel assemblies.

REPLACING RAKE TEETH

To service the landscape rake when attached to the

tractor, it must be blocked up off the ground.

1. Place two blocks under the tinebar. Lower the tinebar

to rest securely on the blocks.

2. Refer to parts drawing, pages 12, 13, and 14. Remove

the nuts and bolts from damaged teeth. Loosen the

other bolts holding the same tooth support plate.

Remove the damaged teeth.

3. Insert the new teeth and secure with the bolts and hex

nuts previously removed.

STORAGE

——————————————————

• At the end of the working season or when the

landscape rake will not be used for a long period, it is

good practice to clean off any dirt that may have

accumulated.

• Inspect the landscape rake for loose, damaged or

worn parts and adjust or replace if needed.

• Storage location should be level and solid to make

hitching and unhitching easy.

• Always store in a safe place away from children or live-

stock.

WARNING!

NEVER GO UNDERNEATH EQUIPMENT. Never

place any part of the body underneath equipment or

between moveable parts even when the engine has

been turned off. Hydraulic system leak down,

hydraulic system failures, mechanical failures, or

movement of control levers can cause equipment to

drop or rotate unexpectedly and cause severe injury

or death.

• Service work does not require going underneath.

• Read Manual for service instructions or have

service performed by a qualified dealer.

WARNING!

Keep all persons away from operator control area

while performing adjustments, service, or mainte-

nance.

Before dismounting power unit or performing any

service or maintenance, follow these steps: disen-

gage power to equipment, lower the 3 point hitch and

all raised components to the ground, operate valve

levers to release any hydraulic pressure, set parking

brake, stop engine, remove key, and unfasten seat

belt.

WARNING!

When using the rake in a reverse position, use extra

care – DO NOT RAM RAKE into dirt or packed snow

piles! Tractor lift arms and the rake are not built to

take high impact loads in this position. RAMMING

backwards can also dislodge operator from seat

and/or tractor controls, resulting in possible serious

injury.

WARNING!

Power unit must be equipped with ROPS or ROPS

cab and seat belt. Keep seat belt securely fastened.

Falling off power unit can result in death from being

run over or crushed. Keep foldable ROPS systems in

“locked up” position at all times.

SAFETY SIGNS

OBEY ALL

SAFETY WARNINGS!!

✔ Keep children away from danger all day, every day.

✔ Please work, drive, play, and live each day with care and

concern for your safety and that of your family and fellow

citizens.

OPERATION

——————————————————

The operator is responsible for the safe operation of this

equipment. The operator must be properly trained.

Operators should be familiar with the equipment, the

tractor, and all safety practices before starting operation.

Read the safety rules and safety decals on page 3

through page 6.

The landscape rake is designed for a wide range of

applications: loosening, leveling, and clearing soil or

debris.

The rake may be angled to windrow material to the side

for removal.

GRADING

Adjust the 3 point hitch upper link so that the frame of

the landscape rake is parallel with the ground. If gauge

wheels are used, adjust them for the amount of cut you

want to take, usually about 1”. Set the rake angle adjust-

ment as desired – straight for grading or angled for a

windrowing effect. It is recommended to operate the rake

at a slow speed (max. 3 mph) to give ample time for fine

material to flow through the tines.

ANGLE GRADING

The rake should be angled horizontally only enough to

allow the material to slide along it easily.The angle (tilt) of

the rake must be set to suit conditions. This is controlled

by the lift arm leveling assembly (turnbuckle) on the trac-

tor 3 point hitch.

LEVELING

The rake should be straight across, i.e., 90° to the line

of travel of the tractor, in other words 0° horizontal angle.

There should be 0° vertical angle, i.e., the lift arms on

the tractor 3 point hitch should be parallel to the ground.

The use of gauge wheels will make the leveling opera-

tion much easier and improve the quality of the job.

When using the rake with gauge wheels, you may need

to adjust the gauge wheels after adjusting pitch to

maintain the desired working depth.

REVERSE OPERATION

Depending on the job, the angle grading or leveling

position may be used. For heavy work, use a regular 3

point rear blade.

NOTE: Most rakes and blades are damaged in this

position – use extra care – DO NOT RAM into obstruc-

tions (including hard packed dirt piles)!

RAKING

Vegetative trash and clods or rocks may be raked into

piles or into windrows for easier pickup.DO NOT overload

rake – remove large rocks, roots, or limbs by other

means.

INCORPORATING SEED

Seed is best incorporated by making two passes in

diagonal directions. Consult your seed supplier or refer-

ence book for the recommended seed depth.Set the rake

straight and operate the rake at two times the

recommended seed depth. Grass seed, for example,

should be covered approximately

”. Operate the rake at

” penetration and make two passes in diagonal direc-

tions. The use of gauge wheels will provide much better

depth control and improve the quality of the job.

These suggestions are generalities; best results will be

obtained after some experience.

NOTE: Do not load either end of the landscape rake

heavily. Try to balance the load on both ends of the land-

scape rake.

INSTRUCTIONS

WARNING!

Power unit must be equipped with ROPS or ROPS

cab and seat belt. Keep seat belt securely fastened.

Falling off power unit can result in death from being

run over or crushed. Keep foldable ROPS systems in

“locked up” position at all times.

Be sure your tractor and loader is in good condi-

tion. Read all the safety precautions and make sure

all equipment operators are familiar with the safety

rules of operation.

CAUTION!

TRACTOR REQUIREMENTS

AND PREPARATION

——————————————————

The DCR, MCR, and LRHD Series Landscape Rakes

will fit most Category I) tractors equipped with a standard

3 point hitch. DCR Series rakes will also fit Category 0

hitch tractors.

NOTE: Some Category 0 tractors have very short lift

arms or

” diameter (Cat. 0) lift arm ball ends. The DCR

Series rakes will fit these tractors if equipped with special

Cat.0 pullpins. The pins need to be installed to the inside

of the 3 pt. frame.

Check the tractor’s 3 point hydraulic lift system.It should

operate up and down smoothly and hold its position when

set. Refer to your tractor owner’s manual or dealer for any

adjustments necessary to put the 3 point hydraulic lift

system in good working order. (I&T shop manuals will list

most specifications and adjustment instructions –

available from most farm equipment dealers.)

Tractor should be equipped with stabilizer bars,

adjustable sway chains, or sway blocks to keep the imple-

ment from swinging side to side.

Smaller size tractors may need front counter weights to

counter-balance the weight of the implement.

CONNECTING LANDSCAPE

RAKE TO TRACTOR

——————————————————

ALL MODELS

The landscape rake is compatible with Category 1, 3

point tractors equipped with side swing-type lower lift

arms and some Category 0 tractors.

1. To avoid interference with the landscape rake, adjust

tractor drawbar to the shortest and highest position.

2. Attach the tractor’s lower lift arms to the landscape

rake and secure in place with lock pin.

For Category 0 Hitch application, order optional pull pin

kit part #590331 (one pair); replace the Category 1 pins

with the Category 0 pins. Make sure the Category 0 pins

are on the inside.

3. Tractor must be equipped with stabilizer bars,

adjustable sway chains, or sway blocks to keep the

implement from swinging side to side.

4. Attach the tractor’s top link to the top of the landscape

rake’s mast and secure with the top link pin and retain-

ing pin supplied with the top link.

IMPORTANT

■■

Make sure rake is at least 6” (15 cm) from tractor

tires throughout complete range of 3 point hitch

operation.

Level the A-frame and tinebar with 3 point connecting

links and top link.Adjusting the top link length will change

the fore and aft pitch of the teeth.

Lengthening the top link will cause the teeth to contact

the ground with a sharper pitch and be more aggressive.

You may need to adjust the optional gauge wheels after

adjusting pitch to maintain the desired working depth.

PACKAGING

——————————————————

The landscape rake is shipped as two bundles:

1. Main Frame with pull pins, bolts and nuts.

2. Rake Tine Bar Assembly (Teeth installed).

ASSEMBLY AND MOUNTING

——————————————————

Preview the assembly instructions and the exploded

view of the landscape rake in your operator’s manual and

become familiar as to how the parts or assemblies go

together.

Select an area for assembly that is clean and free from

debris.

The two main subassemblies of the landscape rake are

heavy and awkward to handle. It is recommended that

you have one or two helpers to complete the assembly.

1. On DCR and MCR models, assemble the “A” frame as

shown in the exploded parts view (pg. 12 or pg. 13).

2. It is suggested that you mount the main frame on the

3 point hitch of your tractor before assembling the

landscape rake as follows:

a. Lower the 3 point hitch on your tractor to facilitate

mounting of the main frame of the rake to the

tractor.

b. Insert the lift arm pins on the main frame into the

ball sockets in the lift arms of the tractor 3 point

hitch. Pin in place with linchpins (not furnished).

NOTE: On DCR models – if your tractor has a Category

0 3 point hitch (20” drawbar spacing), then the lift arm

pins must be installed to the inside of the frame. If the

tractor has a Category I 3 point hitch (26” drawbar

spacing), then the pull pins must be installed on the

outside of the frame.

c. Attach the mast of the main frame to the tractor by

installing the tractor center (or top) link with a top

link pin (not furnished).

NOTE: Use stabilizer bars, adjustable sway chains, or

sway blocks on your tractor lift arms to keep the land-

scape rake from swinging side to side. An anti-sway

device is a must if operating the landscape rake in a

reverse (pushing) position.

3. Install the rake tine bar assembly to the mounting

frame and retain with 1” bolt, flat washer and locknut.

The locknut should be just loose enough for the rake

assembly to pivot.

ASSEMBLY (continued)

——————————————————

GAUGE WHEEL INSTALLATION

——————————————————

SINGLE WHEEL PACKAGE

(DCR Models Only)

Refer to the parts illustration and assemble the wheel

package to the center of the rake frame weldment using

(4) bolts, nuts and washers as shown. Grease the wheel

upon initial assembly.

DUAL WHEEL PACKAGE

(Recommended for rakes above 6’ in width

and all MCR and LRHD Series rakes)

Refer to the parts illustration and install the gauge

wheel arms approximately one foot in from each end of

the rake using longer carriage bolts provided. Grease the

wheels upon initial assembly.

Set up gauge wheels to the desired height using the

spacers and washers provided.Lock caster wheel spindle

in place with linch pin.

The operator is responsible for the safe operation of this

equipment. The operator must be properly trained.

Operators should be familiar with the tractor and attach-

ment, and all safety practices before starting operation.

Read the safety rules and safety signs on pages 3-6.

INSTRUCTIONS (continued)

FOR MODEL LRHD RAKES ONLY

For Category 1 Quick Hitch application, order optional

bushing kit part #862500 (one pair); place bushing over

draw pin and fasten with roll pin.

For Quick Hitch application, the top center hitch hook

will seat into welded 1

” diameter pin. This pin does not

interfere when unit is used with a standard 3 point hitch.

FOR MODEL LRHD RAKES

Place jack stands or suitable blocking under tinebar so

center pivot bolt and 3 pt. mount can be installed.

Place 3 pt. frame assembly on top of the tinebar and

align 1 inch pivot hole with center hole on tine bar.

Install 1 inch pivot bolt and flat washer. Tighten bolt so

3 pt. mount will swing but without excessive looseness.

Place 3 pt. frame in desired position and install angle

shift pin.

Place parking stand in position to support landscape

rake.

INSTRUCTIONS

WARNING!

Power unit must be equipped with ROPS or ROPS

cab and seat belt. Keep seat belt securely fastened.

Falling off power unit can result in death from being

run over or crushed. Keep foldable ROPS systems in

“locked up” position at all times.

Be sure your tractor and loader is in good condi-

tion. Read all the safety precautions and make sure

all equipment operators are familiar with the safety

rules of operation.

CAUTION!

TRACTOR REQUIREMENTS

AND PREPARATION

——————————————————

The DCR, MCR, and LRHD Series Landscape Rakes

will fit most Category I) tractors equipped with a standard

3 point hitch. DCR Series rakes will also fit Category 0

hitch tractors.

NOTE: Some Category 0 tractors have very short lift

arms or

” diameter (Cat. 0) lift arm ball ends. The DCR

Series rakes will fit these tractors if equipped with special

Cat.0 pullpins. The pins need to be installed to the inside

of the 3 pt. frame.

Check the tractor’s 3 point hydraulic lift system.It should

operate up and down smoothly and hold its position when

set. Refer to your tractor owner’s manual or dealer for any

adjustments necessary to put the 3 point hydraulic lift

system in good working order. (I&T shop manuals will list

most specifications and adjustment instructions –

available from most farm equipment dealers.)

Tractor should be equipped with stabilizer bars,

adjustable sway chains, or sway blocks to keep the imple-

ment from swinging side to side.

Smaller size tractors may need front counter weights to

counter-balance the weight of the implement.

CONNECTING LANDSCAPE

RAKE TO TRACTOR

——————————————————

ALL MODELS

The landscape rake is compatible with Category 1, 3

point tractors equipped with side swing-type lower lift

arms and some Category 0 tractors.

1. To avoid interference with the landscape rake, adjust

tractor drawbar to the shortest and highest position.

2. Attach the tractor’s lower lift arms to the landscape

rake and secure in place with lock pin.

For Category 0 Hitch application, order optional pull pin

kit part #590331 (one pair); replace the Category 1 pins

with the Category 0 pins. Make sure the Category 0 pins

are on the inside.

3. Tractor must be equipped with stabilizer bars,

adjustable sway chains, or sway blocks to keep the

implement from swinging side to side.

4. Attach the tractor’s top link to the top of the landscape

rake’s mast and secure with the top link pin and retain-

ing pin supplied with the top link.

IMPORTANT

■■

Make sure rake is at least 6” (15 cm) from tractor

tires throughout complete range of 3 point hitch

operation.

Level the A-frame and tinebar with 3 point connecting

links and top link.Adjusting the top link length will change

the fore and aft pitch of the teeth.

Lengthening the top link will cause the teeth to contact

the ground with a sharper pitch and be more aggressive.

You may need to adjust the optional gauge wheels after

adjusting pitch to maintain the desired working depth.

PACKAGING

——————————————————

The landscape rake is shipped as two bundles:

1. Main Frame with pull pins, bolts and nuts.

2. Rake Tine Bar Assembly (Teeth installed).

ASSEMBLY AND MOUNTING

——————————————————

Preview the assembly instructions and the exploded

view of the landscape rake in your operator’s manual and

become familiar as to how the parts or assemblies go

together.

Select an area for assembly that is clean and free from

debris.

The two main subassemblies of the landscape rake are

heavy and awkward to handle. It is recommended that

you have one or two helpers to complete the assembly.

1. On DCR and MCR models, assemble the “A” frame as

shown in the exploded parts view (pg. 12 or pg. 13).

2. It is suggested that you mount the main frame on the

3 point hitch of your tractor before assembling the

landscape rake as follows:

a. Lower the 3 point hitch on your tractor to facilitate

mounting of the main frame of the rake to the

tractor.

b. Insert the lift arm pins on the main frame into the

ball sockets in the lift arms of the tractor 3 point

hitch. Pin in place with linchpins (not furnished).

NOTE: On DCR models – if your tractor has a Category

0 3 point hitch (20” drawbar spacing), then the lift arm

pins must be installed to the inside of the frame. If the

tractor has a Category I 3 point hitch (26” drawbar

spacing), then the pull pins must be installed on the

outside of the frame.

c. Attach the mast of the main frame to the tractor by

installing the tractor center (or top) link with a top

link pin (not furnished).

NOTE: Use stabilizer bars, adjustable sway chains, or

sway blocks on your tractor lift arms to keep the land-

scape rake from swinging side to side. An anti-sway

device is a must if operating the landscape rake in a

reverse (pushing) position.

3. Install the rake tine bar assembly to the mounting

frame and retain with 1” bolt, flat washer and locknut.

The locknut should be just loose enough for the rake

assembly to pivot.

ASSEMBLY (continued)

——————————————————

GAUGE WHEEL INSTALLATION

——————————————————

SINGLE WHEEL PACKAGE

(DCR Models Only)

Refer to the parts illustration and assemble the wheel

package to the center of the rake frame weldment using

(4) bolts, nuts and washers as shown. Grease the wheel

upon initial assembly.

DUAL WHEEL PACKAGE

(Recommended for rakes above 6’ in width

and all MCR and LRHD Series rakes)

Refer to the parts illustration and install the gauge

wheel arms approximately one foot in from each end of

the rake using longer carriage bolts provided. Grease the

wheels upon initial assembly.

Set up gauge wheels to the desired height using the

spacers and washers provided.Lock caster wheel spindle

in place with linch pin.

The operator is responsible for the safe operation of this

equipment. The operator must be properly trained.

Operators should be familiar with the tractor and attach-

ment, and all safety practices before starting operation.

Read the safety rules and safety signs on pages 3-6.

INSTRUCTIONS (continued)

FOR MODEL LRHD RAKES ONLY

For Category 1 Quick Hitch application, order optional

bushing kit part #862500 (one pair); place bushing over

draw pin and fasten with roll pin.

For Quick Hitch application, the top center hitch hook

will seat into welded 1

” diameter pin. This pin does not

interfere when unit is used with a standard 3 point hitch.

FOR MODEL LRHD RAKES

Place jack stands or suitable blocking under tinebar so

center pivot bolt and 3 pt. mount can be installed.

Place 3 pt. frame assembly on top of the tinebar and

align 1 inch pivot hole with center hole on tine bar.

Install 1 inch pivot bolt and flat washer. Tighten bolt so

3 pt. mount will swing but without excessive looseness.

Place 3 pt. frame in desired position and install angle

shift pin.

Place parking stand in position to support landscape

rake.

WARNING!

When using the rake in a reverse position, use extra

care – DO NOT RAM RAKE into dirt or packed snow

piles! Tractor lift arms and the rake are not built to

take high impact loads in this position. RAMMING

backwards can also dislodge operator from seat

and/or tractor controls, resulting in possible serious

injury.

WARNING!

Power unit must be equipped with ROPS or ROPS

cab and seat belt. Keep seat belt securely fastened.

Falling off power unit can result in death from being

run over or crushed. Keep foldable ROPS systems in

“locked up” position at all times.

SAFETY SIGNS

OBEY ALL

SAFETY WARNINGS!!

✔ Keep children away from danger all day, every day.

✔ Please work, drive, play, and live each day with care and

concern for your safety and that of your family and fellow

citizens.

OPERATION

——————————————————

The operator is responsible for the safe operation of this

equipment. The operator must be properly trained.

Operators should be familiar with the equipment, the

tractor, and all safety practices before starting operation.

Read the safety rules and safety decals on page 3

through page 6.

The landscape rake is designed for a wide range of

applications: loosening, leveling, and clearing soil or

debris.

The rake may be angled to windrow material to the side

for removal.

GRADING

Adjust the 3 point hitch upper link so that the frame of

the landscape rake is parallel with the ground. If gauge

wheels are used, adjust them for the amount of cut you

want to take, usually about 1”. Set the rake angle adjust-

ment as desired – straight for grading or angled for a

windrowing effect. It is recommended to operate the rake

at a slow speed (max. 3 mph) to give ample time for fine

material to flow through the tines.

ANGLE GRADING

The rake should be angled horizontally only enough to

allow the material to slide along it easily.The angle (tilt) of

the rake must be set to suit conditions. This is controlled

by the lift arm leveling assembly (turnbuckle) on the trac-

tor 3 point hitch.

LEVELING

The rake should be straight across, i.e., 90° to the line

of travel of the tractor, in other words 0° horizontal angle.

There should be 0° vertical angle, i.e., the lift arms on

the tractor 3 point hitch should be parallel to the ground.

The use of gauge wheels will make the leveling opera-

tion much easier and improve the quality of the job.

When using the rake with gauge wheels, you may need

to adjust the gauge wheels after adjusting pitch to

maintain the desired working depth.

REVERSE OPERATION

Depending on the job, the angle grading or leveling

position may be used. For heavy work, use a regular 3

point rear blade.

NOTE: Most rakes and blades are damaged in this

position – use extra care – DO NOT RAM into obstruc-

tions (including hard packed dirt piles)!

RAKING

Vegetative trash and clods or rocks may be raked into

piles or into windrows for easier pickup.DO NOT overload

rake – remove large rocks, roots, or limbs by other

means.

INCORPORATING SEED

Seed is best incorporated by making two passes in

diagonal directions. Consult your seed supplier or refer-

ence book for the recommended seed depth.Set the rake

straight and operate the rake at two times the

recommended seed depth. Grass seed, for example,

should be covered approximately

”. Operate the rake at

” penetration and make two passes in diagonal direc-

tions. The use of gauge wheels will provide much better

depth control and improve the quality of the job.

These suggestions are generalities; best results will be

obtained after some experience.

NOTE: Do not load either end of the landscape rake

heavily. Try to balance the load on both ends of the land-

scape rake.

SAFETY INSTRUCTIONS (continued)

Never allow children to operate or be around equipment.

Use stabilizer bars, adjustable sway chains, or sway blocks on your tractor lift arms to keep the implement from

swinging side to side. Adjust as tightly as practical for best performance.

Keep alert and watch the front as well as the rear when working with the implement.

When maneuvering close to buildings or passing through narrow areas, be sure to allow sufficient clearance

for the implement.

Do not operate close to ditches or creeks. Slow down when operating over rough ground.

Always be sure the implement is in the fully raised position when in transport.

When removing, changing the angle, or reversing the rake, be sure that your feet are never under the rake.

Use extreme caution when backfilling deep holes or trenches.

Be careful to avoid catching the rake on stumps or other immovable objects.

Use care when working on slopes.

Avoid excessive speed during operation.

Make adjustments only when the implement is attached to the tractor.

When using the rake in a reverse position, use extra care. Do not ram rake into piles of dirt. Tractor lift arms

and the rake are not built to take high impact loads in this position. Ramming backwards can also dislodge

operator from seat and/or tractor controls, resulting in possible serious injury or death.

Always ease the tractor into the load. It may be necessary to reposition and take less “bite” on the material to

move it safely.

Operating spring steel rake tines may suddenly fling rocks and clods. Keep all bystanders 50 feet away and

operator must wear safety glasses.

Stop power unit and equipment immediately upon striking an obstruction.Turn off engine, remove key, inspect,

and repair any damage before resuming operation.

Before leaving operator’s seat, lower lift arms and put attachment on the ground. Engage brake, stop engine,

remove key, and remove seat belt.

Never perform service or maintenance with engine running.

Watch for and avoid hidden obstructions, i.e., buried pipes, rocks, concrete piers, uneven concrete slabs,

stumps, etc., when operating.

OWNER SERVICE

TRANSPORTING

——————————————————

Pay particular close attention to the Safety Messages

regarding transport. Avoid unnecessary injuries and

equipment damage by exercising cautious, conscientious

travel procedures.

Attaching the landscape rake to the tractor increases

the overall length of the working unit. Allow additional

clearance for the landscape rake to swing when turning.

Always place the rake straight across (90° to line of

travel) for transport.

Raise the landscape rake as high as possible for trans-

porting.

MAINTENANCE

——————————————————

The information in this section is written for operators

who possess basic mechanical skills. If you need help,

your dealer has trained service technicians available. For

your protection, read and follow the safety information in

this manual.

Inspect the landscape rake for loose, damaged or worn

parts and adjust or replace if needed.

Repaint parts where paint is worn or scratched to pre-

vent rust.

Check all bolts and nuts to be sure they are tight.

Periodically grease the gauge wheel assemblies.

REPLACING RAKE TEETH

To service the landscape rake when attached to the

tractor, it must be blocked up off the ground.

1. Place two blocks under the tinebar. Lower the tinebar

to rest securely on the blocks.

2. Refer to parts drawing, pages 12, 13, and 14. Remove

the nuts and bolts from damaged teeth. Loosen the

other bolts holding the same tooth support plate.

Remove the damaged teeth.

3. Insert the new teeth and secure with the bolts and hex

nuts previously removed.

STORAGE

——————————————————

• At the end of the working season or when the

landscape rake will not be used for a long period, it is

good practice to clean off any dirt that may have

accumulated.

• Inspect the landscape rake for loose, damaged or

worn parts and adjust or replace if needed.

• Storage location should be level and solid to make

hitching and unhitching easy.

• Always store in a safe place away from children or live-

stock.

WARNING!

NEVER GO UNDERNEATH EQUIPMENT. Never

place any part of the body underneath equipment or

between moveable parts even when the engine has

been turned off. Hydraulic system leak down,

hydraulic system failures, mechanical failures, or

movement of control levers can cause equipment to

drop or rotate unexpectedly and cause severe injury

or death.

• Service work does not require going underneath.

• Read Manual for service instructions or have

service performed by a qualified dealer.

WARNING!

Keep all persons away from operator control area

while performing adjustments, service, or mainte-

nance.

Before dismounting power unit or performing any

service or maintenance, follow these steps: disen-

gage power to equipment, lower the 3 point hitch and

all raised components to the ground, operate valve

levers to release any hydraulic pressure, set parking

brake, stop engine, remove key, and unfasten seat

belt.