Belkin PM11-EL/RAMA User manual

PM11-EC/RAMA

PM11-EL/RAMA

PM11-UL/RAMA

Rev. A+

Mainboard

Users Manual

55600206

Copyright

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows

®

98, Windows

®

98 SE, Windows

®

ME, Windows

®

2000,

Windows NT

®

4.0 and Windows

®

XP are registered trademarks of

Microsoft Corporation. Intel

®

and Pentium

®

4 are registered

trademarks of Intel Corporation. VIA is a registered trademark of

VIA Technologies, Inc. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

 Use the correct AC input voltage range.

To reduce the risk of electric shock:

 Unplug the power cord before removing the system chassis

cover for installation or ser vicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

 Danger of explosion if battery incorrectly replaced.

 Replace only with the same or equivalent type recommend by

the manufacturer.

 Dispose of used batteries according to the battery

manufacturers instructions.

Joystick or MIDI port:

 Do not use any joystick or MIDI device that requires more than

10A current at 5V DC . There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This users manual contains detailed information about the

mainboard. If, in some cases, some information doesnt match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the mainboard package.

To view the users manual, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click Users

Manual.

Mainboard

This users manual is for the PM11-EC/RAMA, PM11-EL/RAMA and

PM11-UL/RAMA mainboards. The differences between these boards

are shown below.

Onboard Audio (AC97)

Onboard LAN

USB 2.0

Smar t I/O

ü

û

PM11-UL/RAMA

PM11-EL/RAMA

ü

û

PM11-EC/RAMA

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1.2 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 Mainboard Layout ...................................................................................................

2.2 System Memory...........................................................................................................

2.3 Jumper Settings for Clearing CMOS Data........................................

2.4 Jumper Settings for Wake-On-PS/2 Keyboard/Mouse............

2.5 Jumper Settings for Wake-On-USB 2.0 Keyboard/Mouse..

2.6 Por ts and Connectors...........................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1.2 Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 Frequency/Voltage Control............................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.12 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

3.2 Updating the BIOS.....................................................................................................

7

14

56

60

64

69

75

81

84

86

88

89

90

15

18

20

22

23

24

Introduction

1

6

103

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4.2 Hardware Monitor........................................................................................................

4.3 VIA Service Pack...........................................................................................................

4.4 Audio Drivers and Software Applications.............................................

4.5 Onboard LAN Drivers for Windows.......................................................

4.6 Graphics Drivers............................................................................................................

4.7 VIA USB 2.0 Driver....................................................................................................

4.8 Winbond Smar t I/O Drivers.............................................................................

4.9 Winbond SmartCard Application..................................................................

4.10 Microsoft DirectX 8.1 Driver.............................................................................

4.11 Drivers and Utilities Installation Notes.....................................................

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function........................................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................................

B.2 Error Messages..............................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist....................................................................................

91

94

96

97

98

99

105

1

Introduction

7

1.1 Features and Specifications

1.1.1 Features

Chipset

 VIA

®

P4M266/VT8233ACD

Processor

The mainboard is equipped with Socket 478 for installing a Pentium

®

4 processor.

 Intel

®

Pentium

®

4 processor (478-pin)

 Supports up to 2.2GHz CPU speed

 400MHz system data bus

System Memory

 Two 184-pin DDR DIMM sockets

 Supports up to 2GB using PC1600 (DDR200) / PC2100

(DDR266) unbuffered DDR SDRAM DIMM, 2.5V type

 Uses x8/x16 512MB technology

Chapter 1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

1

8

Expansion Slots

The mainboard is equipped with 1 universal AGP slot and 3 PCI

slots.

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The universal

AGP slot supports AGP 2x with up to 533MB/sec. bandwidth and

AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics

applications. AGP in this mainboard will deliver faster and better

graphics to your PC.

Onboard Audio Features

 Supports Microsoft

®

DirectSound/DirectSound 3D

 AC97 supported with full duplex, independent sample rate

converter for audio recording and playback

 S/PDIF compressed digital output

Onboard LAN Features (PM11-EL/RAMA and PM11-UL/RAMA

only)

 Uses Realtek RTL8100 fast ethernet controller

 Integrated IEEE 802.3 10BASE-T and 100BASE-TX compatible

PHY

 32-bit PCI master interface

 Integrated power management functions

 Full duplex support at both 10 and 100 Mbps

 Supports IEEE 802.3u auto-negotiation

 Suppor ts wire for management

Onboard Graphics Features

 Full featured Accelerated Graphics Port (AGP) controller

- AGP specification v2.0 compliant

- Graphics Address Relocation Table (GART)

 High resolution CRT RGB interface

- 250MHz RAMDAC on chip with Gamma correction

- Horizontal/vertical sync outputs compliant with Monitor Power

Management protocols

1

Introduction

9

 Integrated Savage4 2D/3D graphics controller and video

accelerator

- Optimized Shared Memory Architecture (SMA)

- 8/16/32MB frame buffer using system memory

- Single cycle 128-bit 3D architecture

- 8M triangles/second setup engine

- 140M pixels/second tri-linear fill rate

- Next generation 128-bit 2D graphics engine

- High quality DVD video playback

- 2D/3D resolutions up to 1920x1440

 3D rendering features

- MPEG-2 video textures

 2D hardware acceleration features

 Motion video architecture

 Full software support

Onboard Integrated Media Reader - Smart I/O (PM11-UL/RAMA

only)

 Supports Security Application Smart Card interface

 Supports two most promising compact storage - Memory Stick

interface and Secure Digital Memory Card interface

ATX Double Deck Ports (PC 99 color-coded connectors)

 Two USB 2.0 ports (PM11-UL/RAMA only)

 Two USB 1.1 ports

 One RJ45 LAN port (PM11-EL/RAMA and PM11-UL/RAMA

only)

 One DB-9 serial port

 One DB-15 VGA port

 One DB-25 parallel port

 One mini-DIN-6 PS/2 mouse port

 One mini-DIN-6 PS/2 keyboard port

 Three audio jacks: line-out, line-in and mic-in

Connectors

 One connector for 2 additional external USB 2.0 ports

(PM11-UL/RAMA only)

 One connector for 2 additional external USB 1.1 ports

 One connector for 1 external serial port

Introduction

1

10

 One connector for an external game/MIDI port

 One connector for external line-out and mic-in jacks

 Two internal audio connectors (AUX-in and CD-in)

 One S/PDIF-out connector

 One connector for IrDA interface

 Two IDE connectors

 One floppy drive interface supports up to two 2.88MB floppy

drives

 Two ATX power supply connectors

 One Wake-On-LAN connector

 One Wake-On-Ring connector

 CPU fan, chassis fan and chip fan connectors

 1 Smart Card interface (PM11-UL/RAMA only)

 1 Memory Stick interface (PM11-UL/RAMA only)

 1 Secure Digital Memory Card interface (PM11-UL/RAMA only)

PCI Bus Master IDE Controller

 Two PCI IDE interfaces suppor t up to four IDE devices

 Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

 UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-120 and ZIP

IrDA Interface

The mainboard is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices.

USB Ports

The mainboard suppor ts USB 2.0 (PM11-UL/RAMA only) and USB

1.1 ports. USB allows data exchange between your computer and a

wide range of simultaneously accessible external Plug and Play

peripherals.

BIOS

 Award BIOS, Windows

®

98/2000/ME/XP Plug and Play

compatible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades

1

Introduction

11

 Supports DMI 2.0 function

 2Mbit flash memory

Desktop Management Interface (DMI)

The mainboard comes with a DMI 2.0 built into the BIOS. The DMI

utility in the BIOS automatically records various information about

your system configuration and stores these information in the DMI

pool, which is a part of the system board's Plug and Play BIOS.

DMI, along with the appropriately networked software, is designed

to make inventory, maintenance and troubleshooting of computer

systems easier. Refer to chapter 4 for instructions on using the DMI

utility.

1.1.2 System Health Monitor Functions

The mainboard is capable of monitoring the following system health

conditions.

 Monitors the temperature of the CPU and system; and overheat

alarm

 Monitors CPU/3.3V/±5V/±12V/VBAT/5VSB voltages and failure

alarm

 Monitors the fan speed of the CPU fan and chassis fan; and

failure alarm

 Automatic chassis fan on/off control

 Read back capability that displays temperature, voltage and fan

speed

Refer to the PC Health Status section in chapter 3 and the

Hardware Monitor section in chapter 4 for more information.

1.1.3 Intelligence

Automatic Chassis Fan Off

The chassis fan will automatically turn off once the system enters the

Suspend mode.

Dual Function Power Button

Depending on the setting in the Soft-Off By PWRBTN field of the

Power Management Setup, this switch will allow the system to enter

the Soft-Off or Suspend mode.

Introduction

1

12

Wake-On-Ring

This feature allows the system that is in the Suspend mode or Soft

Power Off mode to wake-up/power-on to respond to calls coming

through an internal or external modem. Refer to Wake-On-Ring

Connector in chapter 2 and Resume On LAN/Ring (IRQ/Event

Activity Detect field) in the Power Management Setup section in

chapter 3 for more information.

Important:

If you are using a modem add-in card, the 5VSB power source

of your power supply must support

≥

720mA.

Wake-On-LAN

The Wake-On-LAN function allows the network to remotely wake

up a Soft Power Down (Soft-Off) PC. Your LAN card must support

the remote wakeup function. Refer to Wake-On-LAN Connector in

chapter 2 and Resume On LAN/Ring (IRQ/Event Activity Detect

field) in the Power Management Setup section in chapter 3 for more

information.

Important:

The 5VSB power source of your power supply must support

≥

720mA.

Wake-On-PS/2 Keyboard/Mouse

This function allows you to use the PS/2 keyboard or PS/2 mouse

to wake up the system from the S5 state. Refer to Jumper Settings

for Wake-On-PS/2 Keyboard/Mouse in chapter 2 and PS2KB

Wakeup Select (IRQ/Event Activity Detect field) in the Power

Management section in chapter 3 for more information.

Important:

 If you forgot the password, you must power-off the system,

unplug the power cord and clear the CMOS data. Follow

the steps in the Jumper Settings for Clearing CMOS Data

section in chapter 2.

 The 5VSB power source of your power supply must

support

≥

720mA.

1

Introduction

13

Wake-On-USB Keyboard/Mouse

The Wake-On-USB Keyboard/Mouse function allows you to use a

USB keyboard or USB mouse to wake up a system that is in the

S3 (STR - Suspend To RAM) state.

If you are using this function with a device that is connected to the

USB 2.0 port, you need to configure 2 jumpers. Refer to Jumper

Settings for Wake-On-USB 2.0 Keyboard/Mouse in chapter 2. You

also need to enable Resume on PCI Event (IRQ/Event Activity

Detect field) in the Power Management Setup submenu of the

BIOS.

If you are using this function with a device that is connected to the

USB 1.1 port, you do not need to configure any jumpers. You only

need to enable USB Resume from S3 (IRQ/Event Activity Detect

field) in the Power Management Setup submenu of the BIOS. Refer

to chapter 3 for more information.

Important:

 If you are using the Wake-On-USB Keyboard/Mouse

function for 2 USB ports, the 5VSB power source of your

power supply must support

≥

1.5A.

 If you are using the Wake-On-USB Keyboard/Mouse

function for 3 or more USB ports, the 5VSB power source

of your power supply must support

≥

2A.

RTC Timer to Power-on the System

The RTC installed on the mainboard allows your system to auto-

matically power-on on the set date and time. Refer to Resume On-

Alarm (IRQ/Event Activity Detect field) in the Power Management

Setup section in chapter 3 for more information.

ACPI STR

The mainboard is designed to meet the ACPI (Advanced Configura-

tion and Power Interface) specification. ACPI has energy saving fea-

tures that enables PCs to implement Power Management and Plug-

and-Play with operating systems that support OS Direct Power

Management. Currently, only Windows

®

98/2000/ME/XP supports

the ACPI function. ACPI when enabled in the Power Management

Setup will allow you to use the Suspend to RAM function.

Introduction

1

14

With the Suspend to RAM function enabled, you can power-off the

system at once by pressing the power button or selecting Standby

when you shut down Windows

®

98/2000/ME/XP without having to

go through the sometimes tiresome process of closing files,

applications and operating system. This is because the system is

capable of storing all programs and data files during the entire

operating session into RAM (Random Access Memory) when it

powers-off. The operating session will resume exactly where you left

off the next time you power-on the system. Refer to Using the

Suspend to RAM Function in appendix A for more information.

Important:

The 5VSB power source of your power supply must support

≥

1A.

AC Power Failure Recovery

When power returns after an AC power failure, you may choose to

either power-on the system manually, let the system power-on

automatically or return to the state where you left off before power

failure occurs. Refer to PWR Lost Resume State in the Power

Management Setup section in chapter 3 for more information.

Virus Protection

Most viruses today destroy data stored in hard drives. The

mainboard is designed to protect the boot sector and partition

table of your hard disk drive.

1.2 Package Checklist

The mainboard package contains the following items:

þ The mainboard

þ A users manual

þ One card-edge bracket mounted with a serial port and game/

MIDI port

þ One IDE cable for ATA/33, ATA/66, ATA/100 or ATA/133 IDE

drives

þ One 34-pin floppy disk drive cable

þ One Main Board Utility CD

If any of these items are missing or damaged, please contact your

dealer or sales representative for assistance.

2

Hardware Installation

15

2.1 Mainboard Layout

Chapter 2 - Hardware Installation

PM11-EC/RAMA

(Supports onboard audio)

VIA

P4M266

Socket 478

VIA

VT8233ACD

KB

Mouse

J2

Wake-On-PS/2 KB/Mouse (JP1)

COM 1 (J1)

Parallel (J4)

VGA (CN1)

COM 2 (J9)

CN2

Line-out

Line-in

Mic-in

Game/MIDI

(J8)

AUX-in

(J7)

CD-in

(J6)

AC’97

VT

1612A

Front

audio (J3)

CN3

S/PDIF-out

(J5)

Winbond

W83697HF

Chip fan (J11)

IrDA (J10)

Wake-On-LAN (J7)

BIOS

Wake-On-Ring (J16)

USB 1.1 (J17)

Clear CMOS

(JP2)

RESET

SPEAKER

HD-LED

J21

G-SW

G-LED

PWR-LED

ATX-SW

Chassis

fan (J28)

FDD

(J27)

ATX powe r

(J26)

CPU fan

(J18)

AGP Slot

PCI Slot 1

PCI Slot 2

PCI Slot 3

+12V power

(ATXP1)

Battery

DDR SDRAM

DIMM 1

DDR SDRAM

DIMM 2

USB 1.1

IDE 2

(J23)

IDE 1

(J19)

Mouse

(Green)

KB

(Purple)

COM 1

Parallel

(Burgundy)

Line-In

(Light Blue)

Line-Out

(Lime)

Mic-In

(Pink)

(Teal/Turquoise)

VGA

(Blue)

USB 1.1

(Black)

Square denotes pin 1

USB 1.1

(Black)

PCI Standby Power LED

DIMM Standby

Power LED

2

16

Hardware Installation

PM11-EL/RAMA

(Supports onboard audio and onboard LAN)

VIA

P4M266

Socket 478

VIA

VT8233ACD

KB

Mouse

J2

Wake-On-PS/2 KB/Mouse (JP1)

COM 1 (J1)

Parallel (J4)

VGA (CN1)

COM 2 (J9)

Line-out

Line-in

Mic-in

Game/MIDI

(J8)

AUX-in

(J7)

CD-in

(J6)

AC’97

VT

1612A

Front

audio (J3)

CN3

S/PDIF-out

(J5)

Winbond

W83697HF

Chip fan (J11)

IrDA (J10)

Wake-On-LAN (J7)

BIOS

Wake-On-Ring (J16)

USB 1.1 (J17)

Clear CMOS

(JP2)

RESET

SPEAKER

HD-LED

J21

G-SW

G-LED

PWR-LED

ATX-SW

Chassis

fan (J28)

FDD

(J27)

ATX powe r

(J26)

CPU fan

(J18)

AGP Slot

PCI Slot 1

PCI Slot 2

PCI Slot 3

+12V power

(ATXP1)

Battery

DDR SDRAM

DIMM 1

DDR SDRAM

DIMM 2

IDE 2

(J23)

IDE 1

(J19)

LAN

USB 1.1

CN2

USB 1.1

Realtek

RTL8100

Square denotes pin 1

Mouse

(Green)

KB

(Purple)

COM 1

Parallel

(Burgundy)

Line-In

(Light Blue)

Line-Out

(Lime)

Mic-In

(Pink)

(Teal/Turquoise)

VGA

(Blue)

2 USB 1.1

(Black)

RJ45

LAN

PCI Standby Power LED

DIMM Standby

Power LED

2

Hardware Installation

17

Note:

The illustrations on the following pages are based on the PM11-UL/

RAMA mainboard, which is the board that supports onboard audio,

onboard LAN, USB 2.0 and Smart I/O.

PM11-UL/RAMA

(Supports onboard audio, onboard LAN, USB 2.0 and Smart I/O)

VIA

P4M266

Socket 478

VIA

VT8233ACD

KB

Mouse

J2

Wake-On-PS/2 KB/Mouse (JP1)

COM 1 (J1)

Parallel (J4)

VGA (CN1)

COM 2 (J9)

JUSB1

USB 2.0

LAN

USB 1.1

CN2

USB 1.1

Line-out

Line-in

Mic-in

Game/MIDI

(J8)

AUX-in

(J7)

CD-in

(J6)

AC’97

VT

1612A

Front

audio (J3)

CN3

S/PDIF-out

(J5)

Realtek

RTL8100

Winbond

W83697HF

Chip fan (J11)

IrDA (J10)

VIA

VT6202

USB 2.0

(J12)

J14

J13

Wake-On-USB 2.0 KB/Mouse

(J13 and J14)

Wake-On-

LAN (J7)

BIOS

Wake-On-

Ring (J16)

USB 1.1 (J17)

Clear CMOS

(JP2)

RESET

SPEAKER

HD-LED

J21

G-SW

G-LED

PWR-LED

ATX-SW

W83L518D

SD (J20)

MS

(J24)

SC

(J25)

Chassis

fan (J28)

FDD

(J27)

ATX powe r

(J26)

CPU fan

(J18)

AGP Slot

PCI Slot 1

PCI Slot 2

PCI Slot 3

+12V power

(ATXP1)

Battery

IDE 2

(J23)

IDE 1

(J19)

Square denotes pin 1

2 USB 2.0

(Black)

Mouse

(Green)

KB

(Purple)

COM 1

Parallel

(Burgundy)

Line-In

(Light Blue)

Line-Out

(Lime)

Mic-In

(Pink)

(Teal/Turquoise)

VGA

(Blue)

2 USB 1.1

(Black)

RJ45

LAN

DDR SDRAM

DIMM 1

DDR SDRAM

DIMM 2

PCI Standby Power LED

DIMM Standby

Power LED

2

18

Hardware Installation

2.2 System Memory

Warning:

Electrostatic discharge (ESD) can damage your mainboard, processor,

disk drives, add-in boards, and other components. Perform the

upgrade instruction procedures described at an ESD workstation only.

If such a station is not available, you can provide some ESD

protection by wearing an antistatic wrist strap and attaching it to a

metal part of the system chassis. If a wrist strap is unavailable,

establish and maintain contact with the system chassis throughout

any procedures requiring ESD protection.

The mainboard is equipped with two 184-pin DDR SDRAM DIMM

(Dual In-line Memory Module) sockets that support 2.5V DDR

SDRAM DIMM. Double Data Rate SDRAM (DDR SDRAM) is a

type of SDRAM that doubles the data rate through reading and

writing at both the rising and falling edge of each clock. This

effectively doubles the speed of operation therefore doubling the

speed of data transfer.

Refer to chapter 1 (System Memory section) for detailed

specification of the memory supported by the mainboard.

DDR SDRAM

DIMM 1

DDR SDRAM

DIMM 2

2

Hardware Installation

19

1. Pull the tabs which are at the ends of the socket to the side.

2. Position the DIMM above the socket with the notch in the

module aligned with the key on the socket.

3. Seat the module vertically into the socket. Make sure it is

completely seated. The tabs will hold the DIMM in place.

2.2.1 Installing the DIM Module

A DIM module simply snaps into a DIMM socket on the mainboard.

Pin 1 of the DIM module must correspond with pin 1 of the socket.

Pin 1

Notch

Key

Tab

2

20

Hardware Installation

2.3 Jumper Settings for Clearing CMOS Data

Clear CMOS Data - Jumper JP2

If you encounter the following,

a) CMOS data becomes corrupted.

b) You forgot the keyboard, supervisor or user password.

c) You are unable to boot-up the computer system because the

processors ratio/clock was incorrectly set in the BIOS.

you can reconfigure the system with the default values stored in the

ROM BIOS.

To load the default values stored in the ROM BIOS, please follow

the steps below.

1. Power-off the system and unplug the power cord.

2. Set JP2 pins 2 and 3 to On. Wait for a few seconds and set JP2

back to its default setting, pins 1 and 2 On.

2-3 On:

Clear CMOS Data

1-2 On: Normal

(default)

1

2

3

Clear

CMOS (JP2)

3

2

1

3

2

1

Page is loading ...

Belkin PM11-EL/RAMA User manual

This manual is also suitable for

Belkin PM11-EL/RAMA User manual

Other documents