Kenwood HM791 Owner's manual

Kenwood Limited, New Lane, Havant, Hampshire PO9 2NH, UK

www.kenwoodworld.com

18279/1

Page is loading ...

English 2 - 3

Nederlands 4 - 5

Français 6 - 7

Deutsch 8 - 9

Italiano 10 - 11

Português 12 - 13

Español 14 - 15

Dansk 16 - 17

Svenska 18 - 19

Norsk 20 - 21

Suomi 22 - 23

Türkçe 24 - 25

Ïesky 26 - 27

Magyar 28 - 29

Polski 30 - 31

Русский 32 - 33

Ekkgmij 34 - 36

´¸∂w

37

- 38

Page is loading ...

before using your Kenwood appliance

●

Read these instructions carefully and retain for future

reference.

●

Remove all packaging and any labels.

safety

●

Ensure the cord is fully unwound from the cord wrap

before using the handmixer.

●

Never put the handmixer body in water or let the cord

or plug get wet.

●

Keep fingers, hair, clothing and utensils away from

moving parts.

●

Never let the cord touch hot surfaces or hang down

where a child could grab it.

●

Never use a damaged handmixer. Get it checked or

repaired: see 'service and customer care'.

●

Never use an unauthorised attachment.

●

Always unplug the appliance when not in use, before

fitting or removing parts or before cleaning.

●

This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person

responsible for their safety.

●

Children should be supervised to ensure that they do

not play with the appliance.

●

Only use the appliance for its intended domestic use.

Kenwood will not accept any liability if the appliance is

subject to improper use, or failure to comply with these

instructions.

before plugging in

●

Make sure your electricity supply is the same as the

one shown on the underside of your handmixer.

●

This handmixer complies with European Economic

Community Directive 89/336/EEC.

before using your handmixer for the first time

●

Wash the parts (see 'cleaning').

key

 speed switch

 tool release button

 beaters

 cord wrap

 kneader with additional collar

 kneader without additional collar

 beater storage pillars

 kneader storage pillars

 worktop storage unit

 cord clip

to use your handmixer

1 Unwrap the cord from the cord wrap and make sure

the speed switch is in the off position by lining up the O

symbol on the handmixer body with the dot on the side

of the speed switch. Insert the beaters or kneaders –

turn and push until a positive click is felt. The tabs on

the tool shafts need to line up with the outlet holes.

Important: The kneader with the additional collar will

only fit into the larger outlet hole.

2 Plug in.

3With the ingredients in a suitably sized bowl, place the

beaters/kneaders into the bowl.

4 Pull the speed switch backwards to reach the desired

speed (the first dot on the handmixer body is slow and

speed 5 is fast). Line up the dot on the side of the

speed switch with the corresponding speed.

●

As the mixture thickens, increase the speed.

●

If the machine labours increase the speed.

●

Move the speed switch forwards to the pulse position

(P) to operate the motor as required. The motor will

operate for as long as the pulse is held in position.

5 When the mixture has reached the desired

consistency, return the speed switch to the off

position and then lift the beaters/kneaders out of the

bowl.

2

6To remove the tools, make sure the speed switch is in

the off position and unplug the handmixer. Press the

tool release button. Hold onto the tool shafts when

ejecting the tools.

Important:

●

When making bread dough we recommend that the

dough load does not exceed 400g flour.

●

With heavy mixtures, such as dough, don’t use your

handmixer for longer than 3 minutes in any 5 minute

period as the protection device might operate. Switch

it off as soon as you’ve got the right consistency.

●

To protect your handmixer it is fitted with a protection

device which will stop the handmixer operating if

overloaded. If this happens, switch off, unplug, wait a

couple of minutes and then plug back into the power

supply.

Recommended speeds for beaters

Please note that these are recommendations

only and the speed you select may depend upon

the bowl size, quantities, the ingredients you

are mixing and personal preference.

cleaning

●

Always switch off, unplug and remove the beaters or

kneaders before cleaning.

●

Never put the handmixer body in water or let the cord

or plug get wet.

●

Never use abrasives to clean parts.

beaters, kneaders

●

Wash by hand or in your dishwasher, then dry.

handmixer body and worktop storage unit

●

Wipe with a dry to slightly damp cloth then dry.

storage

1Wrap the cord around the base of the handmixer 

and clip the cord together using the cord clip.

2 Place the handmixer on its end into the worktop

storage unit, ensuring the plug and handle are facing

away from the storage pillars .

3 Store the beaters in the two outside beater storage

pillars.

4 Store the kneader without additional collar in the taller

of the kneader storage pillars.

5 Store the kneader with additional collar in the shorter of

the kneader storage pillars.

service and customer care

●

If the cord is damaged it must, for safety reasons, be

replaced by KENWOOD or an authorised KENWOOD

repairer.

If you need help with:

●

using your appliance or

●

servicing or repairs

Contact the shop where you bought your appliance.

Food type

Recommended

speeds

Egg whites Gradually increase the

speed to 5

Cream 1 - 2

Whisked sponge Gradually increase the

speed to 3

1 stage sponge cake 1 – 3

Batter 1

Rubbing fat into flour. 1

Adding water to combine 1

pastry ingredients

3

Page is loading ...

Kenwood HM791 Owner's manual

Kenwood HM791 Owner's manual

in other languages

Related papers

Other documents