Kenmore Elite 79075503208 User manual

TM

Dual Fuel Range

Estufa de dual fuel

Models/Modelos 790.75503

?:

318200755(0601)Rev.E SearsRoebuck and Co., Hoffman Estates, IL60179 U.S.A. www.sears.com

Liquefied Petroleum (Propane) Gas Conversion ............ 14

Surface Cooking ........................................................ 14-16

Before Setting Oven Controls ........................................ 17

Air Circulation in the Oven ............................................ 17

Setting Oven Controls ............................................... 18-26

Oven Cleaning ........................................................... 27-30

General Cleaning ....................................................... 31-35

Changing Oven Light ..................................................... 36

Adjusting Oven Temperature ......................................... 36

Avoid Service Checklist ............................................. 37-38

EspaSol ........................................................................... 39

Sears Service .................................................... Back Cover

Prod uct Record

In this space below, record the date of purchase, model and serial number of your product. You will find the model and serial

number printed on an identification plate. The identification plate is located on the front frame of the range and isvisible

when the oven door isopen or on the inside of the drawer along the side of the frame.

Model No. 790. Date of purchase

Serial No. Save these instructions and your sales receipt for future reference.

Kenmore Elite Appliance Warranty

One Year Limited Warranty

When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails dueto a

defect in material or workmanship within oneyear from the date of purchase, call 1-800-4-MY-HOME ®to arrange for free repair.If

this appliance isusedfor other than private family purposes,this warranty appliesfor only 90 daysfrom the date of purchase.

This warranty covers only defects in material and workmanship. Sears will NOT pay for:

1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.

2. A servicetechnician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions supplied with the

product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or usefor other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

FIVE-YEAR LIMITED WARRANTY

Forthe second through the fifth year from the date of purchase, when installed and operated according to the Installation

Instructions and Use& Care Guide, Sears will supply the following range parts free of charge if they fail for the reasons

listed below. Customer must pay labor cost of installation.

• Cooktop glass if it fails due to thermal shock.

• Cooktop elements if they are defective.

What Sears will not cover:

• Failure of the product if it isabused, misused, or used for other than the intended purpose.

• Damage to the cooktop glasscaused bythe useof cleaners or utensils other than the recommended cleaning cream and tools.

• Damage to the cooktop glass caused by hardened spills of sugary materials (including starches from vegetables or pastas) or

melted plastic that are not cleaned according to the directions in the Use& Care Guide.

• Repairsto parts or systems resulting from unauthorized modifications made to the appliance.

Disclaimer of implied warranties; limitation of remedies

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied

warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest

period allowed by law. Searsshall not be liable for incidental or consequential damages. Some states and provinces do not

allow the exclusion or limitation of incidental or consequential damages, or limitations on the duration of implied warranties of

merchantability or fitness, sothese exclusions or limitation may not apply to you.

This warranty applies only while this appliance is used in the United States and Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 Printed in United States

2

iMPORTANT SAFETY iNSTRUCTiONS

Read all instructions before using this appliance.

Save these instructions for future reference.

This manual contains many important safety messages. Always read and obey all safety messages.

The safety alert symbol _ calls your attention to safety messages that inform you of hazards that can kill or hurt you or

others, or cause damage to the product.

Indicates an imminently hazardous situation which, if not avoided may result in death or serious injury.

Indicates an imminently hazardous situation which, if not avoided may result in minor or moderate injury, or

product-damage-only.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the

instructions are not followed.

if the information in this manual is not followed

exactly, a fire or explosion may result causing property damage,

personal injury or death.

FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

-- WHATTO DOIFYOU SMELLGAS:

• Do not try to light any appliance.

• Do not touch any eJectricaJ switch; do not use any phone

in your building.

• immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

• if you cannot reach your gas supplier, call the fire

department.

-- installation and service must be performed by a qualified

instaJJer, servicer or the gas suppJier.

• All ranges can tip.

• injury to persons could

result.

• Install anti-tip device

packed with range.

• SeeInstallation

Instructions.

To reduce the risk of tipping, the range

must be secured by properly installed

anti-tip bracket(s) provided with the

range. To check if the bracket(s) is (are)

installed properly, remove the lower

panel or storage drawer and verify that

the anti-tip bracket(s) is(are) engaged.

Refer to the Installation Instructions for

proper anti-tip bracket(s) installation.

Remove all tape and packaging before using the

range. Destroy the carton and plastic bags after

unpacking the range. Never allow children to play with

packaging material.

Proper Installation-Be sure your appliance is properly

installed and grounded by a qualified technician in

accordance with the National Fuel Gas Code ANSI

Z223.1 latest edition, and National Electrical Code

ANSI/NFPA No. 70--latest edition, and local code

requirements. Install only per installation instructions

provided in the literature package for this range.

Ask your dealer to recommend a qualified technician and an

authorized repair service. Know how to disconnect the power

to the range at the circuit breaker or fuse box and gas supply

at the main shutoff valve in case of an emergency. Remove

the drawer to accessthe valve.

• Never modify or alter the construction of a range by

removing leveling legs, panels, wire covers, anti-tip

brackets/screws, or any other part of the product.

Stepping, leaning or sitting on the doors

or drawer of this range can result in serious injuries

and also cause damage to the range. Do not allow

children to climb or play around the range. The weight of a

child on an open door may cause the range to tip, resulting in

serious burns or other injury.

Do not use the oven for storage.

Do not store items of interest to children

in the cabinets above a range or on backguard of a

range. Children climbing on the range to reach items could

be seriously injured.

User servicing--Do not repair or replace any part of the

appliance unless specifically recommended in the

manuals. All other servicing should be done only bya

qualified technician, this may reduce the risk of personal

injury and damage to the range.

NEVER use this appliance as a space heater

to heat or warm the room. Doing so may result in carbon

monoxide poisoning.

Z

tet

Z

iMPORTANT

• Storage in or on Appliance--Flammable materials

should not be stored in an oven, near surface burners

or in the drawer (if equipped). This includes paper, plastic

and cloth items, such ascookbooks, plasticware and towels,

aswell asflammable liquids. Do not store explosives,such as

aerosol cans,on or near the appliance. Flammable materials

may explode and result in fire or property damage.

SAFETY INSTRUCTIONS

Use proper pan size--Adjust flame size

so it does not extend beyond the edge of the utensil.

The use of undersize utensils will exposed a portion of the

burner flame to direct contact and may result in ignition of

clothing. Proper relationship of utensil to flame will also

improve efficiency.

Do not leave children alone--Children should not be

left alone or unattended in the area where appliance

is in use, They should never be allowed to sit or stand on

any part of the appliance.

DO NOTTOUCH SURFACE BURNERS,AREAS NEAR

THESEBURNERS,OVEN HEATING ELEMENTS OR

INTERIOR SURFACESOF THE OVEN. Both surface

burners and oven heating elements may be hot even

though they are dark in color. Areas near surface burners

may become hot enough to cause burns. During and after

use, do not touch, or let clothing or other flammable

materials touch these areas until they have had sufficient

time to cool. Among these areas are the cooktop, surfaces

facing the cooktop, the oven vent openings and surfaces

near these openings, oven door and window.

Wear proper apparel--Loose-fitting or hanging

garments should never be worn while using the

appliance. Do not let clothing or other flammable

materials contact hot surfaces.

Do not usestove top grills on the burner

grates of sealed gas burners. If you use a stove top grill on a

sealed gas burner, it will cause incomplete combustion and

can result in exposure to carbon monoxide levels above

allowable current standards. This can be hazardous to your

health.

Electronic controllers can be damaged by

cold temperatures. When you use your appliance for the

first time, or if it has not been used for a long period of

time, make sure that it has been exposed to a

temperature above 0°C/32°F for at least 3 hours before

connecting it to the power supply.

IMPORTANT INSTRUCTIONS FOR USING YOUR

COOKTOP

• Know which knob controls each surface heating unit.

Always turn the knob to the LITEposition when igniting

the burners. Visually check that burner has lit. Then adjust

the flame so it does not extend beyond the edge of the

utensil.

• Do not use water or flour on grease fires--Smother

the fire with a pan lid, or use baking soda, a dry

chemical or foam-type extinguisher.

• When heating fat or grease, watch it closely, Fat or

grease may catch fire if allowed to become too hot.

In case of fire or gas leak, be sure to turn

off the main gas shutoff valve.

Use only dry potholders--Moist or damp potholders

on hot surfaces may result in burns from steam. Do

not let potholders touch hot heating elements. Do not use

a towel or other bulky cloth instead of a potholder.

• Do not heat unopened food containers--Build-up of

pressure may cause container to burst and result in

injury.

* Remove the oven doors from any unused range if it

is to be stored or discarded.

IMPORTANT--Do not attempt to operate the oven

during a power failure. If the power fails, always turn

the ovens off. If the ovens are not turns off and the power

resumes, the oven may begin to operate again. Food left

unattended could catch fire or spoil.

Use proper pan size. This appliance is equipped with one

or more surface burners of different sizes. Select utensils

having flat bottoms large enough to cover the surface

burner. The use of undersized utensils will expose a portion

of the surface burner to direct contact and may result in

ignition of clothing. Proper relationship of utensil to the

surface burner will also improve efficiency.

Utensil handles should be turned inward and not

extend over adjacent surface burners--To reduce the

risk of burns, ignition of flammable materials, and spillage

due to unintentional contact with the utensil. The handle

of the utensil should be positioned so that it isturned

inward, and does not extend over adjacent surface

burners.

Never leave surface burners unattended at high heat

settings--Boilovers cause smoking and greasy spillovers

that may ignite, or a pan that has boiled dry may melt.

Protective liners--Do not use aluminum foil to line oven

bottom or any other part of the appliance. Only use

aluminum foil as recommended for baking if used as a

cover placed on the food. Any other use of protective

liners or aluminum foil may result in a risk of electric shock

or fire or short circuit.

iMPORTANT SAFETY iNSTRUCTiONS

Glazed cooking utensils--Only certain types of glass, • Do not use the broiler pan without its grid. Tile

glass/ceramic, ceramic, earthenware, or other glazed

utensils are suitable for rangetop servicewithout breaking

due to the sudden change in temperature. Check the

manufacturer's recommendations for rangetop use.

Do not use decorative surface burner covers. If a

burner isaccidentally turned on, the decorative cover will

become hot and possibly melt. Burns will occur if the hot

covers are touched. Damage may also be done to the

cooktop or burners because the covers may cause

overheating. Air will be blocked from the burner and

cause combustion problems.

broiler pan and its grid allow dripping fat to drain and be

kept away from the high heat of the broiler.

Do not cover the broiler grid with aluminum foil.

Exposed fat and grease could ignite.

Do not touch a hot light bulb with a damp cloth,

Doing so could cause the bulb to break. Disconnect the

appliance or turn off the power to the appliance before

removing and replacing light bulb.

IMPORTANT INSTRUCTIONS FOR CLEANING

YOUR RANGE

FOR GLASS COOKTOPS ONLY

• Do not clean or operate a broken cooktop--lf cooktop

should break, cleaning solutions and spillovers may

penetrate the broken cooktop and create a risk of electric

shock. Contact a qualified technician immediately.

• Clean cooktop glass with caution--If a wet sponge or

cloth is used to wipe spills on a hot cooking area, be

careful to avoid a steam burn. Some cleaners can produce

harmful fumes if applied to a hot surface.

• Avoid scratching the cooktop glass with sharp

objects.

IMPORTANT INSTRUCTIONS FOR USING YOUR

OVEN

• Use care when opening oven door--Stand to the side of

the range when opening the door of a hot oven. Let hot

air or steam escape before you remove or replace food in

the oven.

• Keep ovens vents unobstructed. Each vent has its own

vent located on the top, near each side and towards the

back of the cooktop. Touching the surfaces in this area

when the oven is operating may cause severe burns. Also,

do not place plastic or heat-sensitive items on or near an

oven vent. These items could melt or ignite.

• Placement of ovens racks. Always place oven racks in

desired location while ovens are cool. If rack must be

moved while oven is hot use extreme caution. Use

potholders and grasp the rack with both hands to

reposition. Do not let potholders contact the hot heating

elements in the ovens. Remove all utensils from the rack

before moving.

• Clean the range regularly to keep all parts free of

grease that could catch fire. Exhaust fan ventilation

hoods and grease filters should be kept clean. Do not

allow grease to accumulate on hood or filter. Greasy

deposits in the fan could catch fire. When you are flaming

food under the hood, turn the fan on. Refer to the hood

manufacturer's instructions for cleaning. '_:;

• Kitchen cleaners and aerosols--Always follow the ,[[:

manufacturer's recommended directions for use. Be _,;

aware that excess residue from cleaners and aerosols may

ignite causing damage and injury.

SELF CLEANING OVENS

In the self-Cleaning cycle only clean the parts listed

in this Use and Care Guide. Before self cleaning the

oven, remove the broiler pan and any utensils or foods

from the oven.

• Do not use oven cleaners--No commercial oven

cleaner or ovens liner protective coating of any kind

should be used in or around any part of the oven.

• Do not clean door gasket--The door gasket is essential

for a good seal. Care should be taken not to rub, damage

or move the gasket.

• Remove oven racks. Oven racks color will change if left

in the oven during a self-cleaning cycle.

The health of some birds is extremely

sensitive to the fumes given off during the self-cleaning

cycle of any range. Move birds to another well ventilated

room.

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known

to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure

to such substances.

SAVE THESE INSTRUCTION

PROTECTION AGREEMENTS

In the U.S.A.

Master Protection Agreements

Congratulations on making a smart purchase. Your new

Kenmore®product isdesigned and manufactured for years

of dependable operation. But like all products, it may

require preventive maintenance or repair from time to time.

That's when having a Master Protection Agreement can

save you money and aggravation.

Purchase a Master Protection Agreement now and protect

yourself from unexpected hassle and expense.

The Master Protection Agreement also helps extend the life

of your new product. Here's what's included in the

Agreement:

[_ Expert service by our 12,000 professional repair

specialists

1_ Unlimited service and no charge for parts and labor

on all covered repairs

I_ "No-lemon"guarantee- replacement

of your covered product if four or more product failures

occur within twelve months

I_ Product replacement if your covered product can't be

fixed

[_ Annual Preventive Maintenance Check atyou r

request- no extra charge

1_" Fast help by phone- phone support from a Sears

technician on products requiring in-home repair, plus

convenient repair scheduling

I_ Power surge protection against electrical damage

due to power fluctuations

I_ Rental reimbursement if repair of your covered

product takes longer than promised

In Canada

Maintenance Agreements

Your purchase has added value because you can depend

on SearsHomeCentral®for service.With over 2400 Service

Technicians and more than a million parts and accessories,

we have the tools, parts, knowledge and skills to ensure

our pledge: We Service What We Sell.

Your Kenmore®product isdesigned, manufactured

and tested to provide years of dependable operation. But

like all products, it may require service from time to time.

The Sears Maintenance Agreement offers you an

outstanding serviceprogram, affordably priced.

The Sears Maintenance Agreement:

Isyour way to buy tomorrow's service at today's price

Eliminates repair bills resulting from normal wear and tear

Provides phone support from a Searstechnician on

products requiring in-home repair

Even if you don't need repairs, provides an annual

Preventive Maintenance Check, at your request, to

ensure that your product isin proper running condition.

Some limitations apply, For more information about

Sears Canada Maintenance Agreements,

call 1-800-361-6665

Once you purchase the Agreement, a simple phone call is

all that it takes for you to schedule service. You can call

anytime day or night, or schedule a service appointment

online.

Searshasover 12,000 professional repair specialists, who

have accessto over 4.5 million quality parts and

accessories. That's the kind of professionalism you can

count on to help prolong the life of your new purchase for

years to come. Purchase your Master Protection Agreement

today!

Some limitations and exclusions apply,

For prices and additional information call

1-800-827-6655.

Sears Installation Service

For Searsprofessional installation of home

appliances, garage door openers, water heaters,

and other major home items, in the U.S.A. call

1-800-4-MY-HOME ®

REV. 030509

For best result and energy conservation, choose cooking utensils that have these

characteristics:

Selecting Surface

Cooking Utensils

Pansshould have flat bottoms. Check for

flatness by rotating a ruler across the

bottom. There should be no gap between

the pan and ruler.

Note: Always use a utensil for its

intended purpose. Follow manufacturer's

instructions. Some utensils were not made

to be used in the oven or on the cooktop.

Do not usegriddle over

more than one burner becauseit could

damage your cooktop. It can also result in

exposure to carbon monoxide levelsabove

allowable current standards and be

hazardous to your health.

*GOOD

• Flatbottomandstraightsides.

o Tightfitting lids.

oWeight of handledoesnottilt pan.

Paniswell balanced.

• Pansizesmatchthe amountof

foodto be prepared.

• Madeof a materialthat conducts

heatwell.

• Easyto clean.

POOR

_w

e Curved and warped pan

bottoms.

W

• Pan overhangs unit by more than

one inch or 2.5 cm.

® Heavy handle tilts pan.

• Flame extends beyond unit

* Specialty pans such as lobster pots, griddles and pressure cookers may be

used but must conform to the above recommended cookware

requirements.

ifi" ii

Z

DO NOT use a wok if it is equipped

with a metal ring that extends

beyond the burner unit. Because this

ring traps heat, the surface unit and

cooktop surface could be damaged.

Woks with flat bottoms suitable

for use on your cooktop are

available in most cookshop or

hardware stores. Round-

bottomed woks (with a support

ring that does not extend

beyond the burner unit) may

also be used. The metal ring

was designed to support the

wok safelywhen it isfilled with

large amounts of liquids (soup

making) or fat (frying).

Specialty Pans & Trivets

Wire trivets: Do not usewire trivets. Cookware bottoms must be in direct

contact with the grates.

DO NOT usetwo burner units to heat one large pan such as a

roaster or griddle, or allow cooking utensils to boil dry. The bottom surface of

the pan in either of these situations could cause discoloring or crazing of the

appliance cooking surface, and damage to the grates and burner units.

Canning Tips &

Information

Canning

can generate large

amounts of steam. Use

extreme caution to

prevent burns. Always

raise the lid to vent steam

away from you.

1. Use tested recipes and follow instructions carefully. Check with your local Cooperative

Agricultural Extension Service or a manufacturer of glassjars for the latest canning

information.

2. Use flat-bottomed canners only. Heat is spread more evenly when the bottom surface is

flat.

3. Center canner on the burner grate.

4. Start with hot water and a high heat setting to reduce the time it takes to bring the water

to a boil; then reduce the heat setting aslow as possible to maintain a constant boil.

5. It isbest to can small amounts and light loads.

Prevent damage to cooktop and burner grates:

I. Do not usewater bath or pressure canners that extend more than one inch beyond the

edge of the burner grate.

2. Do not leavewater bath or pressure canners on high heat for an extended amount of time.

3. Alternate surface units between each batch to allow the units and surrounding surfaces to

cool down. Tryto avoid canning on the same burner unit all day.

Safe canning requires that harmful micro-organisms are destroyed and the jars

are sealed completely. When canning in a water bath canner, a gentle but steady boil must be

maintained continuously for the required time.

Range features

Main Oven

Light Switch

Side Oven Thermostat

Electronic Oven Controls

Wok Stand

Element

Convection

Element Cover

Ligths (2)

J

Oven

ustable :'1

Oven Rack :'4:_

Door ;,'

f

Handle ....

Grid

Broil Pan

o Q o

• e

Q o o

_ JJJ_ _}i

-- Side Oven

Broil pan &

Grid

Cast Iron

Grates

Standard

Burner

Power

Burner

Cooktop

Surface

Burner

Controls

Ceramic Glass

Cooktop

Oven Door

Drawer

Handle

Simmer

Burner

Standard

Burner

Power

Burner

Control Pad

Functions

Note:

The appearance of your oven control may differ slightly from the one illustrated

below. However, all functions are the same.

READ ALL INSTRUCTIONSCAREFULLYBEFOREUSING THE OVEN.

Detailed instructions for each function follow later in this book.

Forsatisfactory useof your oven, become familiar with the various functions of the oven as

described below.

BAKE

Used to enter the

normal baking mode

CONV. BAKE/ROAST

Used to enter the

convection baking

or roasting mode

CLEAN

Used to select the

UPand DOWN ARROWS

Used to set the clock, the timer

and the oven tern

TIMER

A O_OFF

TIMER

Used to set or cancel

the minute timer. The

minute timer does'nt

start or stop cooking.

CLEAR

Used to clear any oven

J

mode previously

entered except the

time of day and the

self-cleaning mode

VARI BROIL

Used to select the

variable broil mode

BAKETIME

Used to enter the

length of the

baking time.

BAKE STOP\ CLOCK"_-_/ CLEAR

TIME TIME \ OFF minute timer. Push

\_ clear to stop cooking.

STOPTiM E_

Usedwith BAKE, OVEN COOK

TIME, and CLEAN to program _ CLOCK

delayed baking or delayed self- Used to set the

cleaning cycle stop time. time of the day.

Note: Push buttons or pads may be shaped differently.

Note: After the appliance isfirst plugged in, or after a power interruption, the clock must be set

to the correct time of day before the rest of the electronic control functions will operate.

The oven can be programmed for:

• Conventional baking and roasting

• Convection baking and roasting

• Timed baking and roasting (conventional and convection) with automatic on and off times.

• Vari broiling

• Self-cleaning

For a silent control panel:

When choosing a function, a beep will be heard each time a pad is pushed. If desired, the controls can be programmed for

silent operation. Pushand hold STOPTIME After 7 seconds, the control will beep once. This will block the controls from

sounding when a pad is pushed. To return the sound, push and hold STOPTIME again for 7 seconds until a beep is heard.

10

Setting the

Clock

FEATURE OVERVIEW

Clock

• Minute Timer

Clock

When tile range isfirst plugged in, or when tile power supply to tile appliance has been interrupted, tile display will flash.

INSTRUCTIONS

To Set the Clock: (example 1:30)

I. Push CLOCK. The word "TIME" will appear in the display. The

timer allows you 5 seconds to go to step 2.

2. Push and hold the UPor DOWN ARROW to set the time of clay to

1:30. The word "TIME" will disappear after 6 seconds and the clock will

start. You may also push CLEAR OFF; the word "TIME" will

disappear and the clock will start.

DISPLAY

:',p_

Minute Timer

Note: The minute timer does not start or stop cooking and is not active during self-clean. It servesasan extra timer in the

kitchen that will beep when the set time has run out. The minute timer can be used independently during any of the bake or

broil functions. The timer can be set for any amount of time from 5 seconds to 9 hours and 55 minutes.

INSTRUCTION

To Set the Minute Timer

1. PushTIMER ON/OFF, ":00" andtheword "TIMER" will be displayed.

2. Push and hold the UP ARROW until the desired time appears in the

display. As soon asthe UP ARROW is released, the time will begin to

count clown in the display.

3. When the set time has run out, the timer will beep 3 times and will

continue to beep once every 10 seconds for 5 minutes or until TIMER

ON/OFF ispushed.

When settingtheminutetimer for: The time will appear in the

display and increase in:

5 seconds to I minute 59 seconds 5 second increments

2 minutes to 9 minutes. 59 seconds 10 second increments

10 minutes to 59 minutes 59 seconds I minute increments

I hourto 9 hours 55 minutes 5 minute increments

DISPLAY

To Change the Minute Timer:

Push and hold tile UP or DOWN ARROW to increase or decrease tile time.

To Cancel the Minute Timer before the set time has run out:

Pushand hold tile DOWN ARROW until ":00" appears in the display or push TIMER ON/OFF.

11

Consumer

Defined

Control Feature

FEATURE OVERVIEW

Lockout (Child Resistant

Lock)

• Temperature

Conversion

Other Displays

A TIMER

O_/OFF

BAKE STOP CLOCK \ // CLEAR

TIME TIME V OFF

Control Lockout

Lockout allows the oven controls only to be locked. This feature allows cleaning of the control panel without accidentally

activating the oven.

INSTRUCTIONS

Lockout can be set or cancelled by pushing BAKE TiME and STOP TIME

simultaneously for a second. During this mode, depressing any button results in the

word "OFF" being displayed for 2 seconds.

While in Lockout mode, the display will show the current time of day.

DISPLAY

Temperature Conversion (Fahrenheit/Celsius)

Tile electronic oven control isset to operate in °F (Fahrenheit) when shipped from tile factory. To change tile temperature to

°C (Celsius) or from °C to °F:

INSTRUCTIONS

1. PushCONV. Bake/Roast and set the oven temperature to 500°F/260°C or more

using the UP or DOWN ARROW.

2. Push CONV, Bake/Roast within the next 2 seconds for 3-4 seconds. A beep

sounds and a number appears in red to the right of the display. Forthe

conversion, "1 " must be displayed. If another number isdisplayed, push

CONV, Bake/Roast and select "1 ".

3. Pushthe UP or DOWN ARROW to change °F to °C or °C to °F in the display.

4. Push CLEAR OFF to confirm your choice.

DISPLAY

Other Displays

When proceeding through steps 1 and 2 in tile Temperature Conversion or in tile

elimination of the 12-hour Shut-off time limit, two other words can be displayed.

One isESCwith a red 0 which cannot be changed; the other one is USE or SALE

with a red 2 which isfor factory use.

12

_\ TIMER

Consumer

Defined

Control Feature

FEATURE OVERVIEW

Sabbath Feature

* Other Displays

Sabbath Feature

For energy conservation, the Electronic Oven Control has been set at the factory to allow you to program the oven a

maximum of 12 hours in advance (except during timed bake). The Sabbath Feature allows you to program the oven more

than 12 hours in advance. To set the sabbath feature:

INSTRUCTIONS

1. PushCONV. Bake/Roast and set the oven temperature to 500°F/260°C or

more using the UPARROW.

2. Push CONV. Bake/Roast within the next 2 seconds for 3-4 seconds. A beep

sounds and a number appears in red to the right of the display. Forthe

conversion, "3" must be displayed. If another number isdisplayed, push

CONV, Bake/Roast and select "3 ".

3. Pushthe UP or DOWN ARROW to change from 12 hour to 9999 in the

display, for no 12 hour shut-off.

4. Push CLEAR OFF to confirm your choice.

DISPLAY

Other Displays

When proceeding through steps 1 and 2 in the Temperature Conversion or in

the elimination of the 12-hour Shut-off time limit, two other words can be

displayed. One is ESCwith a red 0 which cannot be changed; the other one is

USE or SALE with a red 2 which isfor factory use.

;=

13

Liquefied

Petroleum

(Propane) Gas

Conversion

This appliance can be used with Natural Gas or Propane Gas. It is shipped from

the factory for use with natural gas.

If you wish to convert your range for use with LP/Propanegas, follow instructions

and use the fixed orifices you will find in the bag marked "FOR LP/PROPANEGAS

CONVERSION".

The conversion must be performed by a qualified installer, LPsupplier or service

technician in accordance with the installation instructions furnished with this range

and all codes and requirements of all local codes and requirements. Failure to

follow instructions could result in serious injury or property damage. The qualified

agency performing this work assumes responsibility for the conversion.

Personal injury or death from electrical shock may occur if the

range is not installed by a qualified installer or electrician.

Any additions, changes or conversions required in order for this

appliance to satisfactorily meet the application needs must be made by an

authorized SearsService Center, Distributor or Qualified Agency.

Using the Wok Stand

The Wok Stand provided with your range isdesigned to allow only round-bottomed woks

up to 14 inches in diameter (35.5 cm).

Surface

Cooking

FEATURE OVERVIEW

Using the Wok Stand

Always use

potholders to remove the

wok stand from the grate.

Allow the wok stand to cool

before removing. Do not

set hot wok stand on

surfaces that cannot

withstand high heat such as

countertops.

The Wok Stand must be used on either of the front burners, although it is recommended that

you use the larger burner for best performance.

If properly positioned, the Wok Stand cannot be slid off the grate.

Do not use the rear burner next to the Wok

when this one is on use.

To properly position the Wok Stand:

With the grate in position over the burner, set the Wok Stand on top of the grate. Turn the

Wok Stand, as shown, until the grate fingers fit into the slots on the bottom of the stand.

Be sure the grate stand is positioned correctly and stably before useto prevent

hot spills and possible burns.

Flat-bottomed woks may also be

used on your cooktop without the

Wok Stand.

The WOK STAND fits

over grate fingers.

Round-bottomed woks (with a support ring that does not extend beyond the burner

unit) may also be used without the Wok Stand. The metal ring was designed to support the

wok safely when it isfilled with large amounts of liquids (soup making) or fat (frying).

DO NOT use a wok if it isequipped with a metal ring that extends beyond the burner unit.

Because this ring traps heat, the surface unit and cooktop surface could be damaged.

)

Wron(

Right

14

Flame Size

For most cooking, start on the highest control setting and then turn to a lower one to

complete the process. Usethe table below as a guide for determining proper flame size for

various types of cooking. The size and type of utensil used and the amount of food being

cooked will influence the setting needed for cooking.

Fordeep fat frying, usea thermometer and adjust the surface control knob accordingly. If

the fat istoo cool, the food will absorb the fat and be greasy. If the fat istoo hot, the food

will brown so quickly that the center will be undercooked. Do not attempt to deep fat fry too

much food at once asthe food will neither brown nor cook properly.

*Flame Size

High Flame

Medium Flame

Low Flame

Type of Cooking

Start most foods; bring water to a boil; pan broiling

Maintain a slow boil; thicken sauces, gravies; steam

Keep foods cooking; poach; stew

Surface

Cooking

FEATURE OVERVIEW

• Flame Size

• ProperBurner

Adjustment

• Placement of Burner

Basesand Caps

w

*These settings are based on using medium-weight aluminum pans with lids.

Settings may vary when using other types of pans.

Never extend the flame beyond the outer edge of the utensil. A higher flame simply wastes

heat and energy, and increases your risk of being burned by the flame.

Proper Burner Adjustments

The color of the flame isthe key to proper burner adjustment. A good flame isclear, blue and

hardly visible in a well-lighted room. Eachcone of flame should be steady and sharply defined.

Adjust or clean burner if flame isyellow-orange. To adjust the flame see the Installation

Instructions and to clean burner, see instructions under General Cleaning.

Placement of Burner Bases and Caps Makesure eachburnercap

Place the burner base over each gas opening,

matching the burner base size with the gas

opening size. Placethe burner cap on each

burner base, again matching the cap size to

the burner base size. The cap for the each

Burner has a inner locating ring which locates

the burner cap in the center of the burner.

is properly aligned and

level.

Turnthe burner on to

determine if it will light. If

the burner does not light,

contact a SearsService

Center. Do not service the

sealed burner yourself.

located properly in slot

of eache Burner Head

15

Surface Cooking

FEATURE OVERVIEW

• Placement of Burner

Grates

• Setting Surface Controls

• To Operate the Surface

Burner

Placement of Burner Grates

Place grate over the burners.

Align the tips under each center

of the grate to the holes on the

burner caps. The tip should fit in

the holes. Make sure that each

tips fit in the burner caps of each

of the front and rear burners.

Burner

Grate

Align the Alignment

Fork on the Center

Finger of the grate,

LO

2

3

5

......... J

6

L/7}?I_

Setting Surface Controls

Your cooktop may be equipped with any combination of the following burners:

Simmer Burner; this burner isbest used for simmering delicate sauces, etc.

Standard Burner; can be used for most all surface cooking needs.

Large Burner; the larger burner isbest usedwhen bringing large quantities of liquid to

temperature and when preparing larger quantities of food.

Regardlessof size, always select a utensil that issuitable for the amount and type of food

being prepared. Select a burner and flame size appropriate to the pan. Never allow flames to

extend beyond the outer edge of the pan.

Do not place plastic items such as salt and pepper shakers, spoon

holders or plastic wrappings on top of the cooktop when it is in use. These items

could melt or ignite. Potholders, towels or wood spoons could catch fire if placed too close to

a flame.

To operate the surface burner:

I. Placecooking utensil on burner.

2. Push in and turn the Surface Control knob to LITE Note: All electronic ignitors will click

at the same time. However, only the burner you are turning on will ignite.

3. Visually check that the burner has lit.

4. Push in and turn the Surface Control Knob to the desired flame size. The control knobs

do not have to be set at a particular mark. Use the guides and adjust the flame as

needed. DO NOT cook with the Surface Control knob in the LITE position. (The electronic

ignitor will continue to click if left in the LITE position, causing premature wear.)

In the event of an electrical power outage, the surface burners can be lit manually. To light a

surface burner, hold a lit match to the burner head, then slowly turn the Surface Control knob

to LITE Use caution when lighting surface burners manually.

16

Oven Vent(s) and Racks

Ovens Vents Locations

Each oven has its own vent located on the top, near each side and towards the back of the

cooktop. When an oven ison, warm air isreleased through the vent; this ventilation is

necessary for proper air circulation in the oven and good baking results.

Before Setting

Oven Controls

FEATURE OVERVIEW

• Oven vent(s) and racks

Arranging Oven Racks

ALWAYS ARRANGE OVEN RACKS WHEN THEOVEN IS COOL(PRIORTO

OPERATINGTHEOVEN). Always use oven mitts when using the oven.

To remove an oven rack, pull the rack forward until it stops. Lift up front of

rack and slide out.

To replace an oven rack, fit the rack onto the guides on the oven

walls. Tilt the front of the rack upward and slide the rack back into place.

Side Oven

Main Oven

If using multiple pans, stagger as shown. If using one pan, place in center of oven. Air Circulation

in the Oven

Z

:d>

For best air circulation and baking results, center pans as much as possible. Allow 2-4" (5-10

cm) around the utensil(s) for proper air circulation and be sure pans do not touch each other

or the door, sides and back of oven. The hot air must circulate around the pans in the oven

for even heat to reach all parts of the oven.

17

Setting Oven

Controls

FEATURE OVERVIEW

Manually Operated

Oven Cooking

Manually Operated Oven Cooking:

INSTRUCTIONS

To Set or Change the Temperature for Normal Baking

The oven can be programmed to bake at any temperature from 170% (77°C)

to 550% (288°C).

I. Push BAKE. '.... and the word "BAKE" will be displayed.

2. Pushthe UPor DOWN ARROW. The display will show "350°F ''(177°C). By

holding the UP or DOWN ARROW, the temperature can then be adjusted in 5%

(3°C) increments.

3. As soon asthe UP or DOWN ARROW is released, the oven will start heating.

The display will show the actual oven temperature as it increases to the desired

setting. If preheating isnecessary,wait until the selected temperature isshown

in the display.

4. To cancel the baking function, push CLEAR OFF.

To change the temperature after normal baking/roasting has begun, repeat steps 1 and 2 above.

DISPLAY

To Set or Change Temperature for Convection Baking/Roasting (some models)

I. PushCONV Bake/Roast. '.... and "CONV BAKE" will be displayed.

2. Pushand hold the UP or DOWN ARROW until the desired baking temperature

appears in the display.

3. As soon asthe UP or DOWN ARROW is released, the oven will start heating

and the fan inside the oven will turn. The fan shuts off when the oven door is

opened.

4. To cancel the convection baking/roasting function, push CLEAR OFF.

18

_\ TIMER

Setting Oven

Controls

FEATURE OVERVIEW

• Timed Bake

Timed Bake:

The BAKETIME and STOPTIME pads control the BakeTime operation. The automatic timer will turn the oven on and off at

the times you select in advance. The oven can be programmed to start immediately and shut off automatically or to start

baking at a later time with an automatic shut off.

Use caution when using tile automatic timer. Usetile automatic timer when cooking cured or frozen meats :'i

and most fruits and vegetables. Foods that can easily spoil such as milk, eggs, fish, meat or poultry should be chilled in the :'_

refrigerator first. Evenwhen chilled, they should not stand in the oven for more than I hour before cooking begins, and

should be removed promptly when cooking iscompleted. '[::

INSTRUCTIONS

To Start Heating Immediately and Shut Off Automatically:

I. Besure that the clock shows the correct time of day (example 1:30).

2. Placethe food in the oven.

3. Push BAKE TIME. " : " and the words "BAKE", "TIME" will be

displayed.

4. Pushand hold the UP ARROW until the desired baking time appears in the

display. The baking time can be set for any amount of time from 5 minutes to 11

hours and Bg minutes. When setting the baking time, the time will appear in the

display and increase in 5 minute increments (example 55 minutes).

B. Push BAKE. '.... and the word "BAKE" will be displayed.

6. Pushand hold the UPor DOWN ARROW until the desired baking temperature

appears in the display.

DISPLAY

Once the controls are set:

1. The oven will come on and start heating to the selected baking temperature.

2. The word "ON" will be displayed.

3. The main display will show the oven baking time and count down by minutes

until it reaches ":00".

When the set BAKE TIME runs out:

1. ":00" will be displayed and the oven will shut off automatically.

2. The control will beep 3 times.

3. The control will then continue to beep once every I0 seconds for B minutes or

until CLEAR OFF ispushed.

19

Setting Oven

Controls

FEATURE OVERVIEW

Delayed Timed Bake

Delayed Timed Bake:

INSTRUCTIONS

For a Delayed Start Time and to Shut Off AutomaticalJy:

I. Besure that the clock shows the correct time of day (example 1:30).

2. Placethe food in the oven.

3. Push BAKE TIME. " : " and the words "BAKE", "TIME" will be

displayed.

4. Pushand hold the UP ARROW until the desired baking time appears in the

display. The baking time can be set for any amount of time from 5 minutes to 11

hours and 59 minutes. When setting the baking time, the time will appear in the

display and increase in 5 minute increments (example 55 minutes).

5. Push STOPTIME, The time when the baking will stop will appear in the display

window. The words "BAKE"," STOP'and "TIME" will be displayed.

6. Pushand hold the UP ARROW pad until the time you want the cooking to be

completed appears in the display (example 4:00).

7. Push BAKE, '.... and "DELAY BAKE" will be displayed.

8. Pushand hold the UPARROW until the desired baking temperature appears inn

the display.

9. If the baking temperature is not set, the control will beep. '.... and the

words "DELAY BAKE" will be displayed; the word "BAKE" will flash.

10. The control will calculate backward from the set stop time to determine when

the baking should start. The words "DELAY" and "BAKE STOPTIME" will

remain displayed.

11. The baking will come on automatically at the calculated time. The words

"DELAY" and "BAKE" will go out and "ON" will appear. The main display will

shown the oven baking time and count down by minutes until it reatches ":00".

12. To cancel the countdown, press CLEAR OFF.

DISPLAY

When the set BAKE TIME runs out:

I. ":00" will appear in the display window and the oven will shut off automatically.

2. The control will beep 3 times.

3. The control will then continue to beep once every I0 seconds for B minutes or

until CLEAR OFF is pushed.

20

Page is loading ...

Kenmore Elite 79075503208 User manual

Kenmore Elite 79075503208 User manual

in other languages

Related papers

Other documents