Perel Tools GWP2 User manual

Page is loading ...

3795-B PEREL

2

3795-B – AUTOMATIC SUBMERSIBLE WATER PUMP FOR DIRTY WATER

Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm

the environment.

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized

company for recycling.

This device should be returned to your distributor or to a local recycling service.

Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Perel! Please read the manual thoroughly before bringing this device into service. If the device

was damaged in transit, don't install or use it and contact your dealer.

Safety Instructions

• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer

will not accept responsibility for any ensuing defects or problems.

• Not covered by warranty: damage caused by user modifications to the device, destruction of rotating mechanical

seal by dry-running or addition of foreign bodies in water, blockage of running wheel through foreign bodies,

transport damage, damage caused by unauthorized persons.

• Keep the device away from children and unauthorised users.

Before Start-Up, Note the Following

• The pump can be connected to any shock-proof plug which has been installed according to regulations. The plug

must have a supply voltage of 230VAC~50Hz. Fuse min. 6 amp.

• Before starting to run your new submersible pump, please have the ground connection and the zero conductor

checked by an expert.

• Fault current breaker switch must comply with the safety regulations of the power plants and they must work

faultlessly.

• The electrical connections must be protected from moisture.

• If there is danger of flooding, the electrical connections must be taken to higher ground.

• Circulation of aggressive fluids as well as the circulation of abrasive materials must be avoided at all costs.

• The submersible motor-driven pump must be protected from frost.

• The pump must be protected from running dry.

• Access on the part of children should also be prevented with appropriate measures.

Consistency

Your submersible pump is designated for the circulation of water with a maximum temperature of 35°C. This pump

may not be used for any other fluids and other chemical product.

When used near swimming pools or garden ponds and in their area of protection, the pump

must be equipped with a ground-fault circuit interrupter with a nominal trip current of max.

30mA (according to VDE 0100, parts 702 and 738). Do not operate the pump when people are in

the garden or pool! Please contact your electrician!

3795-B PEREL

3

Installation

The submersible motor pump can be installed as follows:

• in a stationary position with fixed pipeline;

• in a stationary position with a flexible hose pipe.

NOTE: Never install the pump by suspending it unsupported from its delivery pipe or power cable. The submersible

motor pump must be suspended from the specially provided handle or be placed on the bottom of the shaft.

To guarantee that the pump works properly, the bottom of the shaft must be kept free of sludge and dirt. If the

water level sinks too far, any sludge in the shaft will dry out quickly and stop the pump from starting up. It is

therefore necessary to check the submersible motor pump regularly (by carrying out start-up tests). The

floater is adjusted in a way that the pump can immediately be started. The pump shaft should have minimum

dimensions of 40 x 40 x 50cm so that the floating switch can move freely.

Mains Supply

Your new submersible pump is equipped with a shock-proof plug according to regulations. The pump is designed to

be connected to a 230VAC~50Hz safety socket. Make sure that the socket is sufficiently secured (min. 6A) and is in

excellent condition. Insert the plug into the socket to operate the pump.

NOTE: If the mains cable or plug suffers any damage from external action, repairs to the cable are prohibited. This

work may only be performed by a qualified electrician.

Areas of Use

This pump is used primarily as cellar pump. When installed in a shaft, this pump provides protection from flooding.

The pump can also be used wherever water has to be moved from one place to another, e.g. in the home,

agriculture, horticulture, plumbing and many other applications.

Setting to Work

After having read these instructions carefully, you can set your pump to work, reconsidering the following items:

• check if the pump rests on the ground of the shaft;

• check if the pressure cord has been attached properly;

• check the electrical connection (230VAC~50 Hz);

• check if the socket is in good condition;

• make sure that water and humidity can never come to the mains supply;

• avoid dry-running.

Setting the ON/OFF Operating Point

The ON and OFF operating point of the float switch can be set by adjusting the float switch in its latching holder.

Before putting the pump into operation, please check the following:

• The float switch must be installed so that the level of the ON operating point and the level of the OFF operating

point can be reached easily and with little force. To check this, place the pump in a vessel filled with water, raise

the float switch carefully by hand and then lower it again. As you do so, note whether the pump switches on and

off.

• Make sure that the distance between the float switch head and the latching holder is not too small. Proper

operation is not guaranteed if the gap is too small.

• When you set the float switch, make sure that it does not touch the base before the pump switches off. Caution:

risk of dry-running.

3795-B PEREL

4

Maintenance Guidelines

This submersible pump is an approved high-quality product which is subject to severe final controls. We recommend

regular inspection and maintenance to ensure long equipment life and uninterrupted operation.

• Remove the mains plug before all maintenance work.

• In the event that the pump is often transported in the course of operation, it should be cleaned out with clear water

after every use.

• In case of stationary installation, the function of the floating switch should be checked every 3 months.

• All fibrous particles which may have built up inside the pump housing should be removed with a water jet.

• Remove deposits on the floater with clear water.

Cleaning the impeller

If excessive deposits collect in the pump case you must dismantle the bottom part of the pump as follows:

• Remove the intake cage from the pump case.

• Clean the impeller with clear water.

Important! Do not put down or rest the pump on the impeller!

• Assemble in reverse order.

Troubleshooting

Problem Possible Cause Suggested Solution

Pump does not start - No mains supply

- Floater does not switch

- Check mains supply

- Bring floater in a higher position

No flow - Inlet sieve is clogged

- Pressure hose is bent

- Clean inlet sieve water jet

- Reset hose

Pump does not switch off - Floater cannot sink down - Place pump properly on shaft

ground

Insufficient flow - Inlet sieve is clogged

- Reduced pumping capacity by dirty

and abrasive water

- Clean inlet sieve

- Clean pump and replace worn out

parts

Pump switches off after short

operating period

- Thermal cut-out stops pump due to

dirty water

- Water is too hot; thermal cut-out

stops pump

- Remove mains plug, clean pump

and shaft

- Make sure the water temperature

of 35°C is not exceeded

Technical Specifications

Power Supply max. 230VAC / 50Hz

Power Consumption max. 400W

Max. Flow Rate 7000l/h

Max. Pressure 0.7 bar

Max. Height 5m

Max. Grain Size 30mm

Max. Liquid Temperature 35°C

Power Cord 3 G1.5, 10m

Velleman nv cannot be held responsible in the event of damage or injury resulted from (incorrect) use of this

device.

For more info concerning this product, please visit our website www.perel.eu.

The information in this manual is subject to change without prior notice.

Page is loading ...

Perel Tools GWP2 User manual

This manual is also suitable for

Perel Tools GWP2 User manual

in other languages

Other documents