LG LFC20760 User manual

BOTTOM FREEZER

REFRIGERATOR

Owner’s Manual

Please read this guide thoroughly

before operating and keep it handy for

reference at all times.

P/No. MFL48164901

REFRIGERADOR

CON CONGELADOR

INFERIOR

Manual de Usuario

Lea detenidamente estas instrucciones antes de

usar el refrigerador y guárdelas como referencia

para el futuro.

Models / Modelos

LFC20760**

2

TABLE OF CONTENTS

English Version 2

Spanish Version 30

Warranty (U.S.A.) 3 - 4

Safety Instructions 5 - 6

Grounding Requirements 6

Parts and Features 7

Refrigerator Installation 8 - 13

Unpacking your refrigerator

8

Installation 8

Base Grille 8

Removing, Reversing and Replacing

Your refrigerator doors 9 - 13

Pull out drawer 12

Leveling and door alignment 13

Using your refrigerator 14 - 19

Ensuring proper air circulation 14

Multi Flow

Door alarm

14

Setting the controls 14 - 15

Food storage guide 15

Storing frozen food 15

Refrigerator Section 16

Refrigerator shelves 16

Chef Fresh 17

Crisper humidity control 17

Optibin Crisper 17

Crisper cover with lattice on inner surface 18

Design-A-Door 18

Dairy Bin 18

Egg Box 18

Freezer Section 19

Ice Bin 19

Wire Durabase 19

Tilting Door 19

Guide-out drawer basket 19

Care and Cleaning 20 - 21

General cleaning tips 20

Outside 20

Inside walls 20

Door liner and gaskets 20

Plastic parts 20

Condenser coils 20

Light bulb replacement 20 - 21

Power interruptions 21

When you go on vacation 21

About the Custom Cube Ice Maker 22

Connecting the Water Line 23 - 25

Troubleshooting Guide 26 - 29

3

visit our web site/http://www.lgservice.com

LG Electronics

United States of America

LG Electronics will repair or at its option replace, without charge, your product which proves to be defective

in material or workmanship under normal use during the warranty period listed below from the date of

original purchase.

This warranty is good only to the original purchaser of the product during the warranty period as long as it is

in the U.S. including Alaska, Hawaii, and U.S. Territories.

LG Refrigerator / Freezer Warranty Period

Product Parts Labor

Refrigerator / Freezer 1 year 1 year [In-Home Service (Except Model GR-051)]

Sealed System 7 years 1 year [In-Home Service (Except Model GR-051)]

(Compressor, Condenser, Evaporator)

No other express warranty is applicable to this product. THE DURATION OF ANY IMPLIED WARRANTIES.

INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO THE DURATION OF

THE EXPRESS WARRANTY HEREIN. LG ELECTRONICS SHALL NOT BE LIABLE FOR THE LOSS OF

USE OF THE PRODUCT, INCONVIENCE, LOSS OR ANY OTHER DAMAGES, DIRECT OR

CONSEQUENTIAL, ARISING OUT OF THE USE OF OR INABILITY TO USE, THIS PRODUCT OR FOR

ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTY

OF MERCHANTABILITY APPLICABLE TO THIS PRODUCT.

Some States do not allow the exclusion or limitation of incidental or consequential damages or limitations on how

long an implied warranty lasts; so these limitations or exclusions may not apply to you. This warranty gives you

specific legal rights and you may also have other rights which vary from state to state.

LIMITED WARRANTY

THE ABOVE WARRANTY DOES NOT APPLY TO:

1. Service trips to your home to deliver and pickup, install, instruct, or replace house fuses or correct house wiring or

plumbing, or correction of unauthorized repairs.

2. Damage to the product caused by accident, pests, fire, floods, or acts of God.

3. Repairs when your LG product is used in other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, or improper installation.

Therefore, these costs are paid by the consumer.

If the product is installed outside the normal service area, any cost of transportation involved in the repair of the product, or the

replacement of defective parts, shall be borne by the owner.

CUSTOMER ASSISTANCE NUMBERS:

To obtain Warranty Coverage: Retain your Bill of Sale to prove date of purchase.

A Copy of your Sales Receipt must be submitted at the time

warranty service is provided.

To obtain Product or Customer

(24 hrs a day, 7 days per week, 365 days per year)

Service Assistance: Press the appropriate menu option, and have your product type

(Refrigerator), model number, serial number, and ZIP/Postal

Code ready.

To obtain the nearest

Authorized Service Center:

Press the appropriate option, and have your product type

(Refrigerator), model number, serial number, and ZIP/Postal

Code ready.

(24 hrs a day, 7 days per week, 365 days per year)

Call 1-800-243-0000

Damages caused during and/or after delivery

Display, discount, or refurbished units purchased with scratches, dents, or defects.

Proof of purchase is required and must be provided to LG in order to validate warranty.

5.

6.

Page is loading ...

This guide contains many important safety messages. Always read and obey all safety messages.

This is the safety alert symbol. It alerts you to safety messages that inform you

of hazards that can kill or hurt you or others, or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard

signal word DANGER, WARNING, CAUTION. These words mean:

All safety messages will identify the hazard, tell you how to reduce the chance of injury and tell you what can happen if

the instructions are not followed.

SAFETY MESSAGES

WARNING

To reduce the risk of fire, electric shock, or injury

to persons when using your product, basic safety

precautions should be followed, including the following:

NEVER unplug your refrigerator by pulling on the power cord.

Always grip the plug firmly and pull it straight out from the

outlet.

Repair or replace immediately all electric service cords that

have become frayed or otherwise damaged. Do not use a cord

that shows cracks or abrasion damage along its length or at

either the plug or connector end.

When moving your refrigerator away from the wall,

be careful not to roll over or damage the power cord.

DO NOT store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

DO NOT allow children to climb, stand or hang on the

refrigerator doors or shelves in the refrigerator. They could

damage the refrigerator and seriously injure themselves.

Keep fingers out of “pinch point” areas; clearances between

Unplug your refrigerator before cleaning or making any repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

Before replacing a burned-out light bulb, unplug the

refrigerator or turn off power at the circuit breaker or fuse box

in order to avoid contact with a live wire filament. (A burned-

out light bulb may break when being replaced.)

NOTE: Setting

either or both controls to the OFF position does not remove

power to the light circuit.

Read all instructions before using this appliance.

Use this appliance only for its intended purpose as described

in this use and care guide.

After your refrigerator is in operation, do not touch the cold

surfaces in the freezer compartment when hands are damp or

wet. Skin may adhere to the extremely cold surfaces.

In refrigerators with automatic icemakers, avoid contact with

the moving parts of the ejector mechanism, or with the heating

element that releases the cubes. DO NOT place fingers or

hands on the automatic icemaking mechanism while the

refrigerator is plugged in.

DO NOT refreeze frozen foods which have thawed completely.

The United States Department of Agriculture in Home and

Garden Bulletin No. 69 says:

“...You may safely refreeze frozen foods that have thawed if

they still contain ice crystals or if they are still cold below

40°F (4°C).”

“...Thawed ground meats, poultry, or fish that have any off-odor

or off-color should not be refrozen and should not be eaten.

Thawed ice cream should be discarded. If the odor or color of

any food is poor or questionable, get rid of it. The food may be

dangerous to eat.”

“Even partial thawing and refreezing reduces the eating quality

of foods, particularly fruits, vegetables and prepared foods.

The eating quality of red meats is affected less than that of

many other foods. Use refrozen foods as soon as possible to

save as much of their quality as you can.”

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

5

the doors and cabinet are necessarily small. Be careful

when you open the doors when children are in the area.

For personal safety, this appliance must be properly grounded.

Have the wall outlet and the circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

The refrigerator-freezer should be so positioned that the supply

plug is accessible for quick disconnection when accident happens.

Do not store bottles in the freezer compartment - they may

break when frozen, causing damage.

WARNING

CAUTION

You can be killed or seriously injured if you don’t follow instructions.

Indicates an imminently hazardous situation which, if not avoided,

may result in minor or moderate injury, or product damage only.

You will be killed or seriously injured if you don’t follow instructions.

DANGER

IMPORTANT:

Please read carefully.

TO CONNECT ELECTRICITY

RECOMMENDED GROUNDING METHOD

The refrigerator should always be plugged into its own

individual properly grounded electrical outlet rated for

115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a fire

hazard from overheated wires. It is recommended that a

separate circuit serving only this appliance be provided.

Use a receptacle which cannot be turned off with a switch

or pull chain. Do not use an extension cord.

Where a standard two-prong wall outlet is encountered,

it is your personal responsibility and obligation to have it

replaced with a properly grounded three-prong wall outlet.

Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord.

NOTE: Before performing any type of installation,

cleaning, or removing a light bulb, turn the control

(Thermostat, Refrigerator Control or Freezer Control,

depending on the model) to OFF and then disconnect the

refrigerator from the electrical source. When you are

finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator Control or

Freezer Control, depending on the model) to the desired

setting.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain

conditions, we strongly recommend against the use of

an extension cord. However, if you still elect to use

an extension cord, it is absolutely necessary that it be

a UL-listed (in the United States), 3-wire grounding type

appliance extension cord having a grounding type plug

and outlet, and that the electrical rating of the cord be 15

amperes (minimum) and 120 volts.

Use of an extension cord will increase the clearance

needed for the back of the refrigerator.

WARNING

Electrical Shock Hazard

FOR PERSONAL SAFETY, this appliance must be

properly grounded. Have the wall outlet and the

circuit checked by a qualified electrician to make sure

the outlet is properly grounded.

Ensure proper

ground exists

before use.

3-prong

grounding

plug

3-prong

grounding type

wall receptacle

Your old refrigerator may have a cooling system that used If you are throwing away your old refrigerator, make sure

CFCs (chlorofluorocarbons). CFCs are believed to harm the CFC refrigerant is removed for proper disposal by a

stratospheric ozone. qualified servicer. If you intentionally release this CFC

refrigerant, you can be subject to fines and imprisonment

under provisions of environmental legislation.

DANGER: RISK OF CHILD ENTRAPMENT

BEFORE YOU THROW AWAY

YOUR OLD REFRIGERATOR

OR FREEZER

Take off the doors.

Leave the shelves in place so that

children may not easily climb inside.

CFC DISPOSAL

GROUNDING REQUIREMENTS

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous... even if they will sit for “just a few days”. If

you are getting rid of your old refrigerator, please follow

the instructions at right to help prevent accidents.

This appliance contains fluid (refrigerant, lubricant), is

made of parts and materials which are reusable and / or

recyclable. All the important materials should be sent to

the collecton center of waste material and can be reused

after rework (recycling).

For take back, please contact with the local agency.

6

WARNING

POWER CORD REPLACEMENT

If the power cord is damaged, it must be replaced

by the manufacturer, by our service center or by

qualified personal by LG Electronics, to avoid some

risk.

7

Use this section to become more familiar with the parts and features.

NOTE: This guide covers several different models. The refrigerator you have purchased may have some

or all of the items listed below. The locations of the features shown below may not match your model.

PARTS AND FEATURES

*on some models

A

B

C

G

H

I

J

E

F

K

D

L

M

N

O

P

A

L

Digital Sensor Control

Filter (Inside)*

Durabase

Divider

Egg Box *

Refrigerator Door Rack

Freezer Light

Pull out Drawer

B

C

D

F

E

G

H

I

J

K

M

N

O

P

Ice Tray *

Optibin Crisper

Keeps fruits and vegetable fresh and crisper

Chef Fresh / Snack Pan

Can Dispenser *

Shelves

Refrigerator Light

Customcube Icemaker *

Dairy Bin

*

REFRIGERATOR INSTALLATION

UNPACKING YOUR REFRIGERATOR

Remove tape and any temporary labels from your

refrigerator before using. Do not remove any warning-

type labels, the model and serial number label, or the

TechSheet that is attached to back wall of the refrigerator.

To remove any remaining tape or glue, rub the area

briskly with your thumb. Tape or glue residue can also be

easily removed by rubbing a small amount of liquid dish

soap over the adhesive with your fingers. Wipe with warm

water and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see the Important Safety Instructions

section.

Refrigerator shelves are installed in the shipping position.

Please reinstall shelves according to your individual

storage needs.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the

refrigerator for cleaning or service, be sure to protect

the floor. Always pull the refrigerator straight out when

moving it. Do not wiggle or walk the refrigerator when

trying to move it, as floor damage could occur.

INSTALLATION

1. Avoid placing the unit near heat sources, direct sunlight,

or moisture.

2. To avoid vibration, the unit must be level. If required,

adjust the leveling screws to compensate for

unevenness of the floor. The front should be slightly

higher than the rear to aid in door closing. Leveling

screws can be turned easily by tipping the cabinet

slightly. Turn the leveling screws clockwise ( ) to

raise the unit, counterclockwise ( ) to lower it.

3. Install this appliance in an area where the temperature

is between 55°F (13°C) and 110°F (43°C.) If the

temperature around the appliance is too low or high,

cooling ability may be adversely affected.

accumulated during shipping.

2. Install accessories such as ice cube bin, drawers,

shelves, etc., in their proper places. They are packed

together to prevent possible damage during shipment.

3. Let your refrigerator run for 2 or 3 hours before putting

food in it. Check the flow of cold air in the freezer

compartment to ensure proper cooling. Your refrigerator

is now ready for use.

WARNING:

Be careful when you work with hinge, base grille,

stopper etc. You may be injured.

Do not put hands or metal sticks into air vents, base

grille or bottom of refrigerator. You may be injured or

receive an electrical shock.

BASE GRILLE

To remove the base grille:

1. Grasp the grille with both hands.

2. Pull the grille toward yourself.

To install the base grille:

1. Place clips in openings in the metal panel.

2. Push the grille toward the refrigerator until it snaps

into place.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

WARNING

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion or fire.

8

CAUTION: Avoid placing the unit near heat sources,

direct sunlight or moisture.

Explosion Hazard

A proper distance from adjacents items

Please keep the refrigerator at a proper distance from other

things. Too small a distance from adjacent items may result

in lowered freezing capability and increased electricity

consumption charges.

1”

(2.54 cm)

REFRIGERATOR INSTALLATION

9

HOW TO REMOVE REFRIGERATOR DOOR (models without water dispenser)

1. Removing Refrigerator Door

NOTE: Handle appearance may vary.

IMPORTANT: Before you begin, turn the refrigerator OFF and unplug it. Remove food and any bins from doors.

Left Door

Loosen the cover screw (1).

Disconnect door switch wire (2).

Loosen hinge bolts (3).

Lift off the top hinge (4).

Place the door on a non-scratching surface with the inside up.

Right Door

CAUTION: When removing top hinge, be careful that the door does not fall forward.

Loosen the cover screw (1).

Disconnect door switch wire (2).

Loosen hinge bolts (3).

Lift off the top hinge (4).

Place the door on a non-scratching surface with the inside up.

Loosen ground screw (6).

Disconnect wire harness (5).

2. Replacing Refrigerator Door

Right Door

Lower the door onto the middle hinge pin (7).

Make sure the door is aligned with the cabinet.

Replace the top hinge (4) installing hinge

screws (3) to secure it.

Make sure the gasket on the door is flush

against the cabinet and is not folded.

Support the door on the handle side while

securing. And make sure the door is straight

and the gap between the doors is even across

the front.

Install the ground screw (6).

Connect the door switch wire (2).

Tighten the cover screw (1).

Left Door

REFRIGERATOR INSTALLATION

Lower the door onto the middle hinge pin (5).

Make sure the door is aligned with the cabinet.

Replace the top hinge (4) installing hinge

screws (3) to secure it.

Make sure the gasket on the door is flush

against the cabinet and is not folded.

Support the door on the handle side while

securing. And make sure the door is straight

and the gap between the doors is even across

the front.

Connect the door switch wire (2).

Tighten the cover screw (1).

Note: To use like reference the previous image.

7

5

HOW TO REMOVE DOOR HANDLES

NOTE: Handle appearance may vary from illustrations on this page.

1.. Removing Refrigerator Handle

•

Loosen the set screws (1) with the 3/32” Allen

Loosen the handle mounting fasteners (3)

wrench and remove the handle (2).

with the 1/4” Allen wrench.

10

REFRIGERATOR INSTALLATION

11

CAUTION: When you remove the drawer, do not hold

handle. If it comes off, it could cause personal injury.

CAUTION: When laying down the drawer, be careful

not to damage the floor or hurt your feet by the sharp

edges on hinge side.

HOW TO REMOVE AND INSTALL THE

PULLOUT DRAWER

IMPORTANT: To avoid possible injury, product or property

damage, you will need two people to perform the following

instructions.

1. Removing Pullout Drawer

• Pull the drawer open to full lower extension. Remove the

lower basket (1) by lifting basket from rail system.

• Press both hangers with yours thumbs to lift it up.

• Separate the left and right rail cover

• Remove the screws(2) of the rail on both sides.

• With both hands, hold both sides of the door and pull it

up to separate it from the rails.

• With both hands, hold the center of the bar and push it

in to let both rails fitted simultaneously.

1

2

12

HOW TO REMOVE AND INSTALL THE

PULL OUT DRAWER

IMPORTANT: To avoid possible injur or product or property

damage, you will need two people to perform the following

instructions.

2. Installing Pullout Drawer

• With both hands, hold the center of the bar and pull it

out to let both rails out to full extension simultaneously.

• Hook door supports (1) into rail tabes (2) .

• Lower door into final position and tighten the screws (3)

• Make sure you have a right rail cover for each side.

• Align the top holes of the rail cover with the top holes of

the door supports to assemble the rail cover.

• With the drawer pulled out to full extension, insert the

lower basket (4) in the rail assembly.

WARNING: To prevent accidental child and pet

entrapment or suffocation risk. DO NOT allow them to

play inside of drawer.

WARNING: DO NOT step or sit down on Freezer Door.

4

1

2

3

REFRIGERATOR INSTALLATION

Right

Rail cover

Left

Rail cover

Verify the hole’s assembly

REFRIGERATOR INSTALLATION

13

LEVELING AND DOOR ALIGNMENT

Leveling

Your refrigerator has two front leveling screws one on

the right and one on the left. If your refrigerator seems

unsteady or you want the doors to close easier, adjust the

Refrigerator’s tilt using the instructions below:

1. Plug the refrigerator’s power cord into a 3-prong

grounded outlet. Move the refrigerator into its final

position.

2. Turn the leveling screw clockwise to raise that side of

the refrigerator or counterclockwise to lower it. It may

take several turns of the leveling screw to adjust the tilt

of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws.

This makes it easier to adjust the screws.

3. Open both doors again and check to make sure that

they close easily. If not, tilt the refrigerator slightly more

to the rear by turning both leveling screws clockwise. It

may take several more turns, and you should turn both

leveling screws the same amount.

4. Re-adjust if necessary.

5. Replace the base cover.

NOTE: Your new refrigerator is uniquely designed with

two fresh food doors. Either door can be opened or

closed independently of one another. You may have to

exert slight pressure on doors to get them to close

completely.

Door Alignment

If the space between your doors is uneven, follow the

instructions below to align the doors:

1. With one hand, lift up the door you want to raise at

middle hinge.

2. With other hand, use pliers to insert snap ring as

shown.

3. Insert additional snap rings until the doors are aligned.

(Three snap rings are provided with unit.)

14

ENSURING PROPER AIR CIRCULATION

In order to ensure proper temperatures, air must flow

between the refrigerator and freezer sections. As shown

in the illustration below, air enters at top of freezer and

circulates down. From bottom of freezer, air is forced up

to top of refrigerator. Air enters refrigerator through top

vent, then circulates and exists at bottom, where it returns

to freezer.

MULTI-FLOW

Multi-Flow means powerful and effective cooling

operation. This is especially noticeable when new food

is placed in the refrigerator compartment.

If water or foreign substances enter the cool air vent

while cleaning, efficiency will be lowered. In addition, if

gasket is damaged, efficiency may be lowered because

of escaping cool air.

Do not block any of cool air vents with food packages.

If the vents are blocked, airflow will be interrupted and

temperature and moisture problems may occur.

IMPORTANT: Because air circulates between both

sections, any odors formed in one section will transfer to

the other. You must thoroughly clean both sections to

eliminate odors. To prevent odor transfer and drying out of

food, wrap or cover foods tightly. (See the Food Storage

Guide section for details.)

SETTING THE CONTROLS

Your refrigerator has two controls that let you regulate

the temperature in the freezer and refrigerator

compartments.

Initially set the REFRIGERATOR CONTROL and the

FREEZER CONTROL at position number “4”.

Leave it at this setting for 24 hours (one day) to

stabilize. Then adjust the compartment temperature

as desired.

(Models without water dispenser)

USING YOUR REFRIGERATOR

DOOR ALARM

With this feature you´ll listen a alarm when the freezer or

refrigerator door is not closed within 1 minute after it is

opened. These tones repeat every 30 seconds.

The alarm is cancelled when the freezer or the

refrigerator is closed correctly.

Middle Models

R efrigerator control: position 1 to 7, represent the

(32°F to 47°F or 0°C to 8°C)

The higher the number setting, the colder the refrigerator

compartment will become.

Freezer control: position 1 to 7

(-6°F to 8°F or -21°C to -13°C)

When the setting is at a higher number, the freezer

compartment becomes colder.

WARMER

ADJUST

REFRIGERATOR TEMP

4 IS RECOMMENDED

FREEZER TEMP

WARMER

ADJUST

4 IS RECOMMENDED

COLDER

Press the Ice Plus key and the LED will turn

on. This function will remain activated for 24 hours and

intensify the cooling speed of freezer and increase the

amount of ice.

Ice Plus

(Identify your control type)

following temperature range

ADJUSTING CONTROL SETTINGS

Give the refrigerator time to cool down completely before

adding food. It is best to wait 24 hours before you put

food into the refrigerator. The mid-settings indicated in the

previous section should be correct for normal household

refrigerator usage. The controls are set correctly when

milk or juice is as cold as you like and when ice cream

is firm.

The refrigerator control functions as the thermostat for the

entire appliance (refrigerator and freezer sections.) The

higher the number setting, the longer the compressor will

run to keep the temperature colder. The freezer control

adjusts the cold air flow from the freezer to the

refrigerator. Setting the freezer control to a lower

temperature keeps more cold air in the Freezer

compartment to make it colder.

If you need to adjust temperatures in the refrigerator or

freezer, start by adjusting the refrigerator first. Wait 24

hours after the refrigerator adjustment to check the

freezer temperature. If it is too warm or too cold, then

adjust the freezer control as well.

Use the settings listed in the chart below as a guide.

Always remember to wait at least 24 hours between

adjustments.

FOOD STORAGE GUIDE

Storing Fresh Food

Wrap or store food in the refrigerator in airtight and

moisture-proof material unless otherwise noted. This

prevents food odor and taste transfer throughout the

refrigerator. For dated products, check date code to

ensure freshness.

Butter or margarine

Keep opened butter in a covered dish or closed

compartment. When storing an extra supply, wrap

in freezer packaging and freeze.

Cheese

Store in the original wrapping until you are ready to

use it. Once opened, rewrap tightly in plastic wrap or

aluminum foil.

Milk

Wipe milk cartons. For best storage, place milk on interior

shelf, not on door shelf.

Eggs

Store in original carton on interior shelf, not on door shelf.

Fruit

Wash, let dry, and store in refrigerator in plastic bags or in

the crisper. Do not wash or hull berries until you are ready

to use them. Sort and keep berries in their original

container in a crisper, or store in a loosely closed paper

bag on a refrigerator shelf.

Leafy vegetables

Remove store wrapping and trim or tear off bruised and

discolored areas. Wash in cold water and drain. Place in a

plastic bag or plastic container and store in the crisper.

Vegetables with skins (carrots, peppers)

Place in plastic bags or plastic container and store

in crisper.

Fish

Chef fresh

Store most chef fresh in original wrapping as long as it is

airtight and moisture-proof. Rewrap if necessary.

Leftovers

Cover leftovers with plastic wrap or aluminum foil. Plastic

containers with tight lids can also be used.

STORING FROZEN FOOD

NOTE: For further information about preparing food for

freezing or food storage times, check a freezer guide or a

reliable cookbook.

Packaging

Successful freezing depends on correct packaging. When

you close and seal the package, it must not allow air or

moisture in or out. If you do, you could have food odor

and taste transfer throughout the refrigerator and also dry

out frozen food.

Packaging recommendations:

Rigid plastic containers with tight-fitting lids

Straight-sided canning/freezing jars

Heavy-duty aluminum foil

Plastic-coated paper

Non-permeable plastic wraps

Specified freezer-grade self-sealing plastic bags

Follow package or container instructions for proper

freezing methods.

Do not use:

Bread wrappers

Non-polyethylene plastic containers

Containers without tight lids

Wax paper or wax-coated freezer wrap

Thin, semi-permeable wrap

USING YOUR REFRIGERATOR

15

Use fresh fish and shellfish the same day purchased.

RECOMMENDED

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR section Turn

too warm REFRIGERATOR

Door opened often control to next

Large amount of food added higher number,

Room temperature very warm wait 24 hours,

then re-check

FREEZER section too warm/ Turn FREEZER

ice not made fast enough control to next

Door opened often higher number,

Large amount of food added wait 24 hours,

Very cold room temperature Then re-check

(can’t cycle often enough)

Heavy ice usage

Air vents blocked by items Move items out of

airstream

REFRIGERATOR section too Turn

cold REFRIGERATOR

Controls not set correctly for control to next

your conditions lower number,

wait 24 hours,

then re-check

FREEZER section too cold Turn FREEZER

Controls not set correctly for control to next

your conditions lower number,

wait 24 hours,

then re-check

REFRIGERATOR SHELVES

The shelves in your refrigerator are adjustable to meet

your individual storage needs. These units are all glass

shelves.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will

make finding the exact item you want easier; it will also

reduce the amount of time the refrigerator door is open,

saving energy.

IMPORTANT: Do not clean glass shelves with warm

water when they are cold. Shelves may break if exposed

to sudden temperature changes or impact, such as

bumping. For your protection, glass shelves are made

with tempered glass, which will shatter into small pebble-

sized pieces.

NOTE: Glass shelves are heavy. Use special care when

removing them to avoid dropping them.

Adjusting Shelves

Remove shelves from the shipping position and replace

shelves in the position you want.

To remove a shelf

:

Tilt up the front of the shelf in the

direction of (1) and lift it in the direction of (2). Pull the

shelf out.

To replace a shelf : Tilt the front of the shelf up and

guide the shelf hooks into the slots at a desired height.

Then lower the front of the shelf so that the hooks drop

into the slots.

NOTE: Make sure that shelves are level from one side to

the other. Failure to do so may result in the shelf falling or

spilling food.

Sliding Out Shelves (optional on some models)

You can slide some glass shelves in and out of your

refrigerator as follows.

To slide the shelf out, carefully pull front of shelf

toward you.

To slide shelf in, push shelf in until it stops.

To remove a sliding shelf from its metal frame:

1. Pull the shelf out to the stop position.

2. Tilt the front of the shelf up and pull it past the stop position.

3. Lift up the shelf to remove.

R eplace the shelf by reversing the above steps.

Convenience Shelves (on some models)

Folding Shelf: You can store taller items such as gallon

containers or bottles by simply sliding the shelf back.

USING YOUR REFRIGERATOR

16

REFRIGERATOR SECTION

Freezing

Your freezer will not quick-freeze any large quantity of

food. Do not put more unfrozen food into the freezer than

will freeze within 24 hours (no more than 2 to 3 lbs of food

per cubic foot of freezer space). Leave enough space in

the freezer for air to circulate around packages. Be careful

to leave enough room at the front so the door can close

tightly.

Storage times will vary according to the quality and type

of food, the type of packaging or wrap used (airtight and

moisture-proof) and the storage temperature. Ice crystals

inside a sealed package are normal. This simply means

that moisture in the food and air inside the package have

condensed, creating ice crystals.

NOTE: Allow hot foods to cool at room temperature for

30 minutes, then package and freeze. Cooling hot foods

before freezing saves energy.

NOTE: Do not store food near the sensor; it may cause

the sensor to malfunction.

IMPORTANT: Do not store bottles in the freezer

compartment - they may break when frozen,

causing damage.

WARNING

Suffocation Hazard

When using dry ice, provide adequate ventilation.

Dry ice is frozen carbon dioxide (CO )

2

. When it

vaporizes, it can displace oxygen, causing dizziness,

light-headedness, unconsciousness and death by

suffocation. Open a window and do not breathe

the vapors.

USING YOUR REFRIGERATOR

17

NOTE: DO NOT store lettuce or other leafy produce in

this drawer.

COLD

Cauliflower

Cucumbers

Zucchinis

Apples

Corn

Oranges

Grapes

COLDER

Steaks

Hard cheeses

Cold cuts

Bacon

Hot dogs

WARNING: Fruits and vegetables may be damage

at the coldest setting.

CHEF FRESH / SNACK PAN

While holding the chef fresh with one hand, pull it forward

slightly. Lift slightly and pull it out.

On some models is applied an

independent temperature

control.

CRISPER HUMIDITY CONTROL

You can control the amount of humidity in the moisture-

sealed crispers. Adjust the control to any setting between

:Lets moist air out of the crisper for best storage of

fruits.

Keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

and

.

:

(on some models)

“ ”

OPTIBIN CRISPERS (on some models)

The OptiBin Crispers provide fresher-tasting fruit and

vegetables by letting you easily control humidity inside the

crisper. The OptiBin Crispers include: 1) a humidity

control knob at the front of the crisper cover and 2) a

large lattice on the inner surface of the cover to hold

or release moisture.

1

2

To remove the glass:

1. Lift up the glass after inserting a screwdriver under

the crisper cover.

To remove the crisper:

1. Slide crisper straight out to the stop.

2. Lift the front of the crisper, then pull it out to remove.

3. Replace the crisper by sliding it back in fully past

the drawer stop.

2. Pull up and out.

USING YOUR REFRIGERATOR

18

USING YOUR REFRIGERATOR

CRISPER COVER WITH LATTICE ON INNER

SURFACE (on some models)

To remove the crisper cover:

1. Remove both crisper drawers.

2. While holding the crisper cover support (2), pull the

cover up and out(1).

CAUTION: Be careful when handing glass cover since

glass is not attached to cover.

To remove the lattice on inner surface:

1. Remove crisper cover(as illustrated above).

2. Hold the glass cover and overtum crisper cover.

3. For each lattice hold lattice and pull sides of the cover

outward to remove lattice.

To replace lattice on inner surface:

1. For each lattice insert middle tab in 1 (closed to glass

cover)and pull sides of the cover to insert lattice.

DESIGN-A-DOOR

The door bins are removable for easy cleaning and

adjusting.

1. To remove the bin, simply lift the bin up and pull

straight out.

2. To replace the bin, slide it in above the desired support

button and push down until it stops.

WARNING: Somebody can be hurt if door bins are not

firmly assembled.

NOTE: DO NOT adjust a bin that is loaded with food.

CAUTION: DO NOT allow children to play with

baskets. Sharp corners on baskets could cause injury.

DAIRY BIN

1. To remove the dairy bin, simply lift it and pull straight

out.

2. To replace the dairy bin, slide it in above the desired

location and push down until it stops.

EGG BOX (on some models)

Store Egg Box on interior shelf, not on door shelf.

CAUTION: Do not use the egg box as an ice storage

bin in the freezer compartment. The egg box can

easily break if it freezes.

11

22

USING YOUR REFRIGERATOR

19

FREEZER SECTION

ICE BIN (on some models)

1. To separate the ice bin, pull out the drawer as much as

possible.

2. Gently lift and pull out the ice bin.

3.

To reinstall, pull out the drawer as much as possible and set

the ice bin in its correct position, and then push in the drawer.

DRAWER

ICE BIN

DURABASE (on some models)

To remove the Durabase, push it back to the end as

much as possible. Tilt up the front of the Durabase and

pull straight out.

2. To install, insert the Durabase in rail assembly.

1.

TILTING DOOR (on some models)

The tilting door provides easy access for stored foods.

How to use:

Tilt the door down and pull it out.

WARNING: Be careful when you open tilting door so

that you do not injure your foot!

11

22

DURABASE DIVIDER (on some models)

The Durabase divider allows you to organize the

Durabase area into sections.

1. To remove, pull divider staight up.

2. To install, hook top corners of divider over top edge of

durabase.

To

1

2

To remove, lift basket up and pull out straight out.

GLIDE OUT DRAWER BASKET -

1.

2. To Install, pull both rails out to full extension.

Hook the basket supports into the rail tabs and push to

the back of compartment.

(on some models)

Both the refrigerator and freezer sections defrost

automatically. However, clean both sections about once

a month to prevent odors. Wipe up spills immediately.

GENERAL CLEANING TIPS

Unplug refrigerator or disconnect power.

Remove all removable parts, such as shelves,

crispers, etc.

Use a clean sponge or soft cloth and a mild detergent in

warm water. Do not use abrasive or harsh cleaners.

Hand wash, rinse and dry all surfaces thoroughly.

Plug in refrigerator or reconnect power.

OUTSIDE

Waxing external painted metal surfaces helps provide rust

protection. Do not wax plastic parts. Wax painted metal

surfaces at least twice a year using appliance wax (or

auto paste wax). Apply wax with a clean, soft cloth.

For products with a stainless steel exterior, use a clean

sponge or soft cloth and a mild detergent in warm water.

Do not use abrasive or harsh cleaners. Dry thoroughly

with a soft cloth.

INSIDE WALLS (allow freezer to warm up so

cloth won’

t stick)

To help remove odors, you can wash the inside of the

refrigerator with a mixture of baking soda and warm water.

Mix 2 tablespoons baking soda to 1 quart of water (26 g

soda to 1 liter water.) Be sure the baking soda is

completely dissolved so does it not scratch the surfaces

of the refrigerator.

DOOR LINERS AND GASKETS

Do not use cleaning waxes, concentrated detergents,

bleaches, or cleaners containing petroleum plastic parts.

PLASTIC PARTS (covers and panels)

Do not use paper towels, window sprays, abrasive

cleansers, or flammable fluids. These can scratch or

damage the material.

CONDENSER COILS

Remove grille base. (See the grille base section

Use a vacuum cleaner with an extended attachment to

clean condenser coils.

Vacuum coils when dusty or dirty. Coils may need to be

cleaned as often as every other month.

Replace grille base.

LIGHT BULB REPLACEMENT

NOTE: Not all appliance bulbs will fit your refrigerator. Be

sure to replace the bulb with one of the same size, shape

and wattage.

To change the refrigerator light:

1. Unplug the power cord from the outlet.

2. Remove refrigerator shelves.

3.

4. Turn the bulb counterclockwise.

5. To assemble, first insert the hooks at the back and

CARE AND CLEANING

WARNING

Electrical Shock Hazard

Before replacing a burned-out light bulb, either unplug

the refrigerator or turn off power at the circuit breaker

or fuse box.

NOTE: Moving the control to the OFF position

does not remove power to the light circuit.

20

WARNING

Explosion Hazard

Use non-flammable cleaner.

Failure to do so can result in death, explosion, or fire.

)

Release the hooks on the front of the light shield

with the help of a flat screwdriver and pull the

shield down to remove it.

then push up the light shield.

To change the freezer light:

1. Unplug refrigerator or disconnect power.

2. Reach behind light shield to remove bulb.

4. Plug in refrigerator or reconnect power.

POWER INTERRUPTIONS

If the electricity goes off, call the power company and ask

how long it will be off.

1. If the power will be out for 24 hours or less, keep

both refrigerator doors closed to help foods stay

cold and frozen.

2. If the power will be out for more than 24 hours:

a) Remove all frozen food and store it in a frozen

food locker.

OR

b)

Place 2 lbs of dry ice in the freezer for every cubic

foot of freezer space. This will keep the food frozen

for two to four days. While handling dry ice, wear

gloves to protect your hands from frostbite.

OR

c)

If neither a food locker nor dry ice is available,

consume or can perishable food at once.

WHEN YOU GO ON VACATION

If you choose to leave the refrigerator on while you

are away, follow these steps to prepare your refrigerator

before you leave.

1. Use up any perishables and freeze other items.

2. Empty the ice bin.

If you choose to turn the refrigerator off before you

leave, follow these steps.

1. Remove all food from the refrigerator.

2. Depending on your model, set the thermostat control

(refrigerator control) to OFF. See the Setting the

Controls section.

3.

Clean refrigerator, wipe it and dry well.

4. Tape rubber or wood blocks to the tops of both doors to

prop them open far enough for air to get in. This stops

odor and mold from building up.

WHEN YOU MOVE

When you are moving your refrigerator to a new home,

follow these steps to prepare it for the move.

1. Remove all food from the refrigerator and pack all

frozen food in dry ice.

2. Depending on your model, turn the thermostat control

(refrigerator control) to OFF. See the

Setting the

Controls section.

3. Unplug the refrigerator.

4. Empty water from the defrost pan.

5. Clean, wipe and dry thoroughly.

6. Take out all removable parts, wrap them well and tape

them together so they don’t shift and rattle during the

move.

7. Depending on the model, raise the front of the

refrigerator so it rolls more easily OR screw in the

leveling legs all the way so they don’

t scrape the floor.

See the

Door Closing section.

8. Tape the doors shut and tape the power cord to the

refrigerator cabinet.

When you get to your new home, put everything back

and refer to the Installing Your Refrigerator section for

preparation instructions.

CARE AND CLEANING

21

3. Replace bulb with a wattage indicated in

11

the refrigerator section, as shown in picture .

11

Page is loading ...

LG LFC20760 User manual

LG LFC20760 User manual

in other languages

Related papers

Other documents