Acme United PLB110S Specification

Model: PLB-110S

Universal

wall bracket

www.acme.eu

3

GB 4 Installation Instruction 100 Warranty card

LT 12 Montavimo instrukcija 101 Garantinis lapas

LV 20 Uzstādīšanas instrukcija 102 Garantijas lapa

EE 28 Paigaldusjuhend 103 Garantiileht

PL 36 Instrukcja instalacji 104 Karta gwarancyjna

DE 44 Installationsanleitung 105 Garantieblatt

FI 52 Asennusohjeet 106 Takuulomake

SE 60 Installation Instruktion 107 Garantisedel

RO 68 Instrucţiuni de montare 108 Fişa de garanţie

BG 76 Инструкции за монтаж 109 Гаранционен лист

RU 84 Инструкция по установке 110 Гарантийный талон

UA 92 Інструкція по установці 111 Гарантійний лист

4

5

GB

Unpacking instructions

• Carefully open the carton, remove contents and lay out on cardboard

or other protective surface to avoid damage.

• Check package contents against the Supplied Parts List in the next

page to assure that all components were received undamaged. Do

not use damaged or defective parts.

• Carefully read all instructions before attempting installation.

Important safety information

Install and operate this device with care. Please read this instruction

before beginning the installation, and carefully follow all instructions

contained herein. Use proper safety equipment during installation.

Please call a qualied installation contractor for help if you:

• If you don’t understand these directions or have any doubts about the

safety of the installation.

• If you are uncertain about the nature of your wall, consult a qualied

installation contractor.

Do not use this product for any purpose or in any conguration not

explicitly specied in this instruction. We hereby disclaim any and all

liability for injury or damage arising from incorrect assembly, incorrect

mounting, or incorrect use of this product.

This TV mount must be securely attached to the

vertical wall. If the mount is not properly installed it

may fall, resulting in possible injury and/or damage.

Tools Required

•5/32"(4mm) Drill Bit

•Screwdriver

•3/8”(10mm)

Masonry Bit

•Stud Finder

• Wrench or Socket Set

• Carpenter’s Level

Note: The mounting components and hardware supplied in this package

are not designed for installations to walls with steel studs or to cinder block

walls. If the hardware you need for your installation is not included, please

consult your local hardware store for proper mounting hardware for the

application.

WARNING

6

7

GB

Supplied parts list Mounting the monitor

brackets to a TV with ﬂat back

First of all, make sure the diameter of the Bolt (e,f,g,h) your TV requires.

Once you have determined the correct diameter, please see the relative

diagram as below. You will thread the Bolt into the TV using the correct

Lock Washer (m,n,o,p) and Washer (s,t). Please make sure the Monitor

Brackets (b,c) are vertically centered and level with each other.

M4 Diameter Bolt

M6 Diameter Bolt

M5 Diameter Bolt M8 Diameter Bolt

Diagram 1A

8

9

GB

Mounting the monitor

brackets to a TV with curved

back

First of all, make sure the diameter of the Bolt (i,j,k,l) your TV requires.

Once you have determined the correct diameter, please see the relative

diagram as below. You will thread the Bolt into the TV using the correct

Lock Washer(m,n,o,p), Washer(s,t) and spacer (q,r). For the M4 or M5

diameter bolt, you will need another M4/M5 Washer between the

Monitor Bracket and the Spacer. Please make sure the Monitor Brackets

are vertically centered and level with each other.

M4 Diameter Bolt

M6 Diameter Bolt

M5 Diameter Bolt

M8 Diameter Bolt

Diagram 1B

Mounting the wall plate

to the wall

Brick, Solid Concrete and Concrete Block mounting:

Use the Wall Plate(a) as a template to mark 6 hole locations on the wall.

Three in the top row of slots and three more in the bottom row. Make sure

these holes are level and there is at least 6”(150mm) distance between

any two holes. Pre-Drill these holes with a 3/8”(10mm) masonry bit to

at least 3”(75mm) in depth. Insert a Concrete Anchor(w) into each of

these holes. Make sure the anchor is seated completely ush with the

concrete surface even if there is a layer of drywall or other material in

front. Attach the Wall Plate to the wall using 6pcs Lag Bolts(u) and 6pcs

Lag Bolt Washers(v), shown in Diagram 2A.

Wood Stud mounting:

The Wall Plate(a) must be mounted to two wood studs at least

16”(406mm) apart. Use a stud nder to locate two adjacent studs. It is

a good idea to verify where the studs are located with an awl or thin

nail shown in Diagram 2B. Pre-drill a 3”(75mm) deep hole at the desired

height in each stud using a 5/32”(4mm) drill bit. Make sure these holes

are in the center area of the studs and level with each other. Use the Wall

Plate as a template to mark the location of the second hole in each stud.

Drill 3”(75mm) deep holes using the 5/32”(4mm) drill bit in the marked

locations. Attach the Wall Plate to the wall using the 4pcs Lag Bolts(u)

and 4pcs Lag Bolt Washers(v).

Diagram 2A Diagram 2B

Stud Finder

16 inch

10

11

GB

Attaching monitor to wall plate

and adding the safety bolts

Warning: Some TVs may require two people to lift! We are not responsible

for personal injury or product damage.

First hook the Monitor Brackets(b,c) over the top of the wall Plate(a), then

let the bottom of the Monitor Brackets rotate to the bottom of the Wall

Plate as shown in the Diagram 3A. Use the Allen Key(d) to tighten the

safety bolts. Then the Monitor Bracket will sit behind the bottom tab on

the Wall Plate as shown in the Diagram 3B.

Thanks for choosing our products, enjoy the using.

Diagram 3BDiagram 3A

wall wall

Safety bolt

Levelling mount

You can re-level the mount after the mount has been installed on wall.

Levelling is achieved by rotating the front plate the TV sits on. First,

remove the TV from mount. Then slightly loosen the 5 screws using the

Allen Key. Place level on top front of plate as shown and level accordingly.

Tighten the 5 screws, do not over tighten.

WARNING!

Use two people to lift and position the TV onto the Wall Plate.

Diagram 4

Page is loading ...

100

101

GB

Warranty card www.acme.eu/warranty

Product Product model

Product purchase date Seller name, address

Failures (date, description, position of the person who accepts the product, rst name, last

name and signature)

1. Warranty period

Warranty enters into force starting with the day when the buyer acquires the product

from the seller. Warranty period is indicated on the package of the product.

2. Warranty conditions

The warranty is valid only by providing an original document of the product acquisition

and this warranty sheet, which includes name of the product model, product purchase

date, name and address of the seller.

If it is noticed during the warranty period that the product has faults and these faults

where not caused by any of the reasons when the warranty is not applied as indicated in

the paragraphs below, manufacturer undertakes to replace the product.

The warranty is not applied to regular testing, maintenance and repair or replacement of

the parts which are worn out naturally.

The warranty is not applied if damage or failures occurred due to the following reasons:

• Inappropriate installation of the product, inappropriate usage and/or operating the

product without following the manual, technical requirements and safety standards

as provided by the manufacturer, and additionally, inappropriate warehousing, falling

from heights as well as hard strikes.

• Corrosion,mud,waterandsand.

• Repair works, modications or cleaning, which were performed by a service not

authorised by the manufacturer.

• Usageofthespareparts,softwareorconsumptivematerialswhichdonotapplytothe

product.

• Accidentsoreventsoranyotherreasonswhichdonotdependonthemanufacturer,

which includes lightning, water, re, magnetic eld and inappropriate ventilation.

• Ifthe productdoes notmeet standardsandspecications ofa particular country,in

which it was not bought. Any attempt to adjust the product in order to meet technical

and safety requirements such as those in the other countries withdraws all the rights to

the warranty service.

If no failures are detected in the product, all the expenses in relation to the service are

covered by the buyer.

LT

Garantinis lapas www.acme.eu/warranty

Gaminys Gaminio modelis

Gaminio pirkimo data Pardavėjo pavadinimas, adresas

Gedimai (data, aprašymas, gaminį priėmusio asmens pareigos, vardas, pavardė ir parašas)

1. Garantinis laikotarpis

Garantija galioja nuo tos dienos, kada pirkėjas nusipirko šį gaminį iš pardavėjo. Garantijos

laikotarpis nurodyats ant gaminio pakuotės.

2. Garantijos sąlygos

Garantija galioja tik pateikus gaminio pirkimo dokumento originalą ir šį garantijos lapą,

kuriame nurodyta gaminio modelio pavadinimas, gaminio pirkimo data, pardavėjo

pavadinimas ir adresas.

Jei garantiniu laikotarpiu bus aptikta gaminio defektų, kurie neatsirado dėl priežaščių,

išvardintų pastraipose garantija netaikoma, gamintojas įsipareigoja gaminį sutaisyti arba

pakeisti.

Garantija netaikoma reguliariam tikrinimui, priežiūrai ir įprastiniu būdu nusidėvėjusių

dalių remontui arba keitimui.

Garantinija netaikoma, jei žala arba gedimai atsirado dėl:

• netinkamo gaminio instaliavimo, netinkamo naudojimo ir/arba darbo su gaminiu

nesilaikant gamintojo pateiktų naudojimo instrukcijų, techninių reikalavimų ar

saugumo standartų, be kita ko ir dėl netinkamo sandėliavimo, kritimo ant žemės ir

stiprių smūgių.

• korozijos,purvo,vandensarbasmėlio.

• remonto,modikacijųarbavalymo,atliktonegamintojoįgaliotameservisocentre.

• gaminiuinetinkamųatsarginiųdalių,programinėsįrangosarbasąnaudiniųmedžiagų

naudojimo.

• nelaimingųatsitikimųarbaįvykiųarbabetkokiųpriežasčių,kuriomsgamintojasneturi

įtakos, be kita ko ir dėl žaibo, vandens, ugnies, magnetinių laukų ir netinkamo vėdinimo.

• jei gaminys neatitinka konkrečios šalies, kuri nėra pirkimo šalis, standartų arba

specikacijų. Bet koks bandymas pritaikyti gaminį kitų valstybių techniniams ar

saugumo reikalavimams panaikina visas teises į garantinį aptarnavimą.

Gaminyje neaptikus gedimų visas su aptarnavimu susijusias išlaidas apmoka pirkėjas.

Page is loading ...

www.acme.eu

Model: PLB-110S

Universal

wall bracket

www.acme.eu

Acme United PLB110S Specification

Acme United PLB110S Specification

in other languages

Related papers

Other documents