Moog Videolarm IGDW75CF1 Operating instructions

www.videolarm.com

I G L O O D O M E

An Air-Conditioned Solution for hot, humid climates

Installation and Operation Instructions for the following models:

IGDW75C1N Outdoor air conditioned dome housing with wall and pole mount, clear

polycarbonate dome, with 240VAC input, heater/blower, 120 to 24VAC

transformer for xed camera

IGDW75T1N Tinted version

Before attempting to connect or operate this product,

please read these instructions completely.

CERTIFIED

81-IN5434

05-06-2010

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualified installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the

unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including amplifiers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specified by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the

integrity of the installation is intact. Failure to comply with the foregoing could result in the

unit separating from the support structure and falling, with resultant damages or injury to

anyone or anything struck by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make

future shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us

at the following number:

The lightning flash with an arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence

of non-insulated “dangerous voltage”

within the product’s enclosure that may be

of sufficient magnitude to constitute a risk

to persons.

Este símbolo se piensa para alertar al usuario a la

presencia del “voltaje peligroso no-aisIado” dentro del

recinto de los productos que puede ser un riesgo de

choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la

presence “de la tension dangereuse” non-isolée dans la

clôture de produits qui peut être un risque de choc

électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença

“di tensão perigosa non-isolada” dentro do cerco dos

produtos que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla

presenza “di tensione pericolosa” non-isolata all’interno

della recinzione dei prodotti che può essere un rischio di

scossa elettrica

.

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones

importantes en la literatura que acompaña la

aplicación.

Ce symbole de point d’exclamation est prévu pour

alerter l’utilisateur à la presence des instructions

importantes dans la littérature accompagnant

l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der

Literatur alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido

alertar o usuário à presença de instruções importantes

na literatura que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti

nella letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING TO

QUALIFIED SERVICE PERSONNEL.

LIMITED WARRANTY

FOR VIDEOLARM INC. PRODUCTS

VIDEOLARM INC. warrants this Product to be free from defectsin material or workmanship,as follows:

PRODUCTCATEGORY PARTS LABOR

All Enclosuresand Electronics Five (5) Years Five (5) Years

Pan/Tilts Three (3) Years **6 months if usedin autoscan Three (3) Years **6 months if usedin autoscan

Poles/PoleEvators Three (3) Years Three (3) Years

Warrior/Q-View/I.R.Illuminators Five (5) Years Five (5) Years

Controllers Five (5) Years Five (5) Years

PowerSupplies Five (5) Years Five (5) Years

AccessoryBrackets Five (5) Years Five (5) Years

During the labor warranty period, to repair the Product,Purchaserwill either return the defective product, freight prepaid,or deliver it to Videolarm Inc.

Decatur GA.The Productto be repaired is to be returned in either its original carton or a similar package

an equal degree of protection with a

RMA# (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA#you must contact our TechnicalSupport

Teamat 800.554.1124,extension 101.Videolarm will return the repaired Productfreight prepaid to Purchaser.Videolarm is not obligated to provide

Purchaserwith a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchasermust pay all labor and/or

parts charges.

1.NOTIFICATIONOF CLAIMS: WARRANTYSERVICE:If Purchaser believes that the Product is defective in material or workmanship, then written notice

with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the

warranty period. If after investigation Videolarm determines that the reported problem was not covered by the warranty, P

urchaser shall pay Videolarm

for the cost of investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall

extend the warranty period as to the entire Product. The

warranty on the repaired part only shall be in for a period of ninety (90) days

following the repair or replacement of that part or the remaining period of the Product parts warranty, whichever is greater.

2.EXCLUSIVE REMEDY: ACCEPTANCE:Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair

any Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3.EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service

during the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts

of God (i.e., hurricanes, earthquakes),

failure of the end-user to follow the directions outlined in the product instructions, failure of the

end-user to follow the maintenance procedures recommended by the International Security Industry Organization, written in product instructions,

or recommended in the service manual for the Product. Furthermore, Videolarm shall have no liability where a schedule is

for regular

replacement or maintenance or cleaning of certain parts (based on usage) and the end-user has failed to follow such schedule; attempted repair by

personnel; operation of the Product outside of the published environmental and electrical parameters, or if such Product’s original

(trademark, serial number) markings have been defaced, altered, or removed. Videolarm excludes from warranty coverage Products sold

AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser. All software and accompanying

documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided

otherwise in any documentation or license agreement furnished with the Product.

4.PROOF OF PURCHASE:The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMEROF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH

REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF

THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE

STATE STATUTE. VIDEOLARM HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM

PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS PURCHASER CHOOSES TO CONNECT TO PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF VIDEOLARM, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE

PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT

OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

/tour operation

**6 months if usedin autoscan

/tour operation

**6 months if usedin autoscan

/tour operation

SView Series Five (5) Years

Five (5) Years

The limited warranty stated in these product instructions is subject to all of the following terms and conditions:

TERMS AND CONDITIONS

Igloo Dome

Power 120VAC .

50/60 H

2.

300 WATTS.

Tools Required: Phillips Head Screwdriver.

Ceiling Support Wires(14 AWG wire min.)

Energía 120VAC.

50/60 H

2

.

300 VATIOS.

Las herramientas requirieron: Destornillador principal

Phillips.

Alambres de la ayuda del techo

(14 de alambre del AWG Min.)

Puissance 120VAC.

50/60 H

2

.

300 WATTS.

Outils requis : Tournevis phillips.

Fils de soutien de plafond (14 de fil d'A.W.G. mn)

Energie 120VAC.

50/60 H

2

.

300 WATT.

Werkzeuge erfordert: Kreuzkopfschraubenzieher.

Decken-Stützdrähte (14 AWG-Lehredraht Min.)

Poder 120VAC.

50/60 de H2.

300 WATTS.

As ferramentas exigiram: Chave de fenda principal de

Phillips.

Fios da sustentação do teto

(14 de fio Calibre de diâmetro de fios Min.)

Potere 120VAC.

50/60 di H2.

300 WATT.

Gli attrezzi hanno richiesto: Cacciavite phillips. Legare

di sostegno del soffitto

(14 del legare dell'AWG min.)

!!

Electrical Specifications

Français

Deutsch

Italiano

Portuguese

Español

English

Mechanical Options

1. Air ow sensor available to be combined with camera output systems

to monitor the eectiveness of air lter. If improper air ow is detected,

sensor will send alarm. If user by passes air ow sensor, air lter should

be changed approximately every 6 months (depending on monitoring

environment).

2. The Igloo Dome incorporates an automatic cool-down safety

precaution system which deactivates the power of both the camera and

cooling system when internal temperatures exceed 167°F (75°C). Once

safe operating conditions resume, the camera and cooling system will

reactivate.

3. Condensation and water run-o is a by product of the Igloo Dome's

cooling system. To prevent damage to the internal electrical

components, the Igloo Dome consists of a water run-o hose, located

underneath the optical dome. Please use caution that small amounts of

water accumulation will be present directly underneath the Igloo Dome,

resulting in slippery conditions.

* A 50/50 blend of propylene glycol and water has a freezing point of

-26°F. If lower temperature protection is required, it can readily be

attained by increasing the concentration of propylene glycol Antifreeze -

for example; a 60/40 blend of Antifreeze and water gives antifreeze

protection to -54°F.

Content of Box

COOLANT

Page is loading ...

Place the mounting plate against the wall

• Coloque la pletina contra la pared

• Placez le plat de support contre le mur

• Setzen Sie die Montageplatte gegen die Wand

• Coloc a placa de montagem de encontro à parede

• Disponga il giunto di supporto contro la parete

Attach with (4) anchor bolts, (4) lock washers, and (4)

flat washers

• Fijación con (4) los pernos de ancla, (4) arandelas de cerradura, y (4) arandelas

planas

• Attache avec (4) des boulons d'anchrage, (4) rondelles de freinage, et (4) rondelles

plates

• Befestigung mit (4) Ankerbolzen, (4) Federringe und (4) flache Unterlegscheiben

• Anexo com (4) parafusos de escora, (4) arruelas de fechamento, e (4) arruelas lisas

• Attaccatura con (4) bulloni d'ancoraggio, (4) ranelle di bloccaggio e (4) rondelle

piane

Tighten all bolts securely

• Apriete todos los pernos con seguridad

• Serrez tous les boulons solidement

• Ziehen Sie alle Schraubbolzen sicher fest

• Aperte todos os parafusos firmemente

• Stringa saldamente tutti i bulloni

Hang the Igloo Dome unit onto the wall mount

• Cuelgue la unidad Deputy2 sobre el montaje de la pared

• Accrochez l'unité Igloo Dome sur le bâti de mur

• Hängen Sie die Iglu-Haubemaßeinheit auf die Wandeinfassung

• Pendure a unidade da abóbada do Igloo na montagem da parede

• Appenda l'unità Igloo Dome sul supporto della parete

12

13

14

11

Page is loading ...

18

3026 Mounting

Plate

Mounting

Hole

Mounting

Hole

Mounting Hole

Axis 214

(52

mm

) 2"

Captive

Screw

(3) #8 x 3/8”

Install the camera to the mounting plate using (3) 3mm x 12mm bolts and lock washers. Place (3) #8x3/8”

screws on the spacers and line up the mounting slots. Slide plate in and secure.

• Instale la cámara fotográfica a la placa de montaje usando (3) los pernos de 3m m x de 12m m y las arandelas de cerradura.

Coloque los tornillos de (3) del # 8x3/8"en los espaciadores y alinee las ranuras de montaje. Resbale la placa adentro y

asegúrela.

• Installez l'appareil-photo sur le plat de support en utilisant (3) des boulons de 3mm x de 12mm et des rondelles de freinage.

Placez les vis de (3) # de 8x3/8"sur les entretoises et alignez les fentes de support. Glissez le plat dedans et le fixez.

• Bringen Sie die Kamera zur Montageplatte mit (3) 3mm x 12mm den Schraubbolzen und den Federringen an. Setzen Sie (3) #

8x3/8"die Schrauben auf die Distanzscheiben und richten Sie die Befestigungsschlitze aus. Schieben Sie Platte innen und sichern

Sie.

• Instale a câmera à placa de montagem usando (3) os parafusos de 3mm x de 12mm e as arruelas de fechamento. Coloque os

parafusos de (3) # de 8x3/8"nos espaçadores e alinhe-os acima dos entalhes de montagem. Deslize a placa dentro e fixe-a.

• Installi la macchina fotografica al giunto di supporto usando (3) i bulloni di 12mm x di 3mm e le ranelle di bloccaggio. Disponga

le viti di 8x3/8"# di (3) sui distanziatori ed allinei le scanalature di montaggio. Faccia scorrere la piastra dentro e fissi.

29

Install the camera to the mounting plate with (4) #8 screws and lock washers provided. Place (3) #8x3/8”

screws on the spacers and align the mounting slots. Slide on plate and camera then secure.

• Instale la cámara fotográfica a la placa de montaje con (4) los tornillos #8 y las arandelas de cerradura proporcionadas. Coloque los

tornillos de (3) del # 8x3/8"en los espaciadores y alinee las ranuras de montaje. Resbale en la placa y la cámara fotográfica entonces

seguras.

• Installez l'appareil-photo sur le plat de support avec (4) les vis #8 et les rondelles de freinage fournies. Placez les vis de (3) # de 8x3/8"

sur les entretoises et alignez les fentes de support. Glissez du plat et de l'appareil-photo puis bloqués.

• Bringen Sie die Kamera zur Montageplatte mit (4) den bereitgestellten Schrauben #8 und Federringen an. Setzen Sie (3) # 8x3/8"die

Schrauben auf die Distanzscheiben und richten Sie die Befestigungsschlitze aus. Schieben Sie auf die sichere Platte und Kamera dann.

• Instale a câmera à placa de montagem com (4) os parafusos #8 e as arruelas de fechamento fornecidas. Coloque os parafusos de

(3) # de 8x3/8"nos espaçadores e alinhe os entalhes de montagem. Deslize na placa e na câmera então seguras.

• Installi la macchina fotografica al giunto di supporto con (4) le viti #8 e le ranelle di bloccaggio fornite. Disponga le viti di 8x3/8"# di (3)

sui distanziatori ed allinei le scanalature di montaggio. Faccia scorrere sulla piastra e sulla macchina fotografica allora sicure.

Holes

Mounting

Holes

1"

2"

Mounting

Axis 215

30

Page is loading ...

3mm

Screw

Power

Board

Connection

Module

20

This is what the typical path of illumination will look like with the setting at 30 degrees.

• Quite a tablero de energía situado dentro de la cubierta. Una el módulo de la conexión según lo demostrado. Una

a esta asamblea a la cubierta usando (1) "arandela del tornillo 6-32x3/8 y de la estrella.

• Enlevez carte d'alimentation situé à l'intérieur du logement. Attachez le module de raccordement comme montré.

Attachez cette assemblée au logement en utilisant (1) la "vis 6-32x3/8 et tenez le premier rôle la rondelle.

• Entfernen Sie das Energie Brett, das innerhalb des Gehäuses befunden wird. Bringen Sie das Anschlußmodul an, wie

gezeigt. Bringen Sie diese Versammlung zum Gehäuse mit (1) "Schraube 6-32x3/8 und Sternunterlegscheibe an.

• Remova a placa de poder situada dentro da carcaça. Una o módulo da conexão como mostrado. Una este

conjunto à carcaça usando (1) do "arruela parafuso 6-32x3/8 e da estrela.

• Rimuova il bordo di alimentazione situato all'interno dell'alloggiamento. Fissi il modulo del collegamento come

indicato. Fissi questo complessivo all'alloggiamento usando (1) "rondella della vite 6-32x3/8 e della stella.

Remove the power board located inside the housing. Attach the connection module as shown.

Attach this assembly to the housing using (1) 6-32x3/8” screw and star washer.

This is what the typical path of illumination will look like with the setting at 30 degrees.

• Termine el cableado a la cámara fotográfica. Una el montaje de la cámara fotográfica a la cubierta resbalando

(3) las ranuras abiertas del tornillo sobre los tornillos en la cubierta; apriete los sujetadores en el soporte.

• Accomplissez le câblage à l'appareil-photo. Attachez l'appareil-photo au logement en glissant (3) les fentes

ouvertes de vis au-dessus des vis dans le logement ; serrez les attaches sur la parenthèse.

• Führen Sie die Verdrahtung zur Kamera durch. Bringen Sie die Kamera zum Gehäuse an, indem Sie die (3) geöffne-

ten Schraube Schlitze über den Schrauben im Gehäuse schieben; ziehen Sie die Befestiger am Haltewinkel fest.

• Termine a fiação à câmera. Una o conjunto da câmera à carcaça deslizando (3) os entalhes abertos do parafuso

sobre os parafusos na carcaça; aperte os prendedores no suporte.

• Completi i collegamenti alla macchina fotografica. Fissi il complessivo della macchina fotografica all'alloggiamento

facendo scorrere (3) le scanalature aperte della vite sopra le viti nell'alloggiamento; stringa i fermi sulla staffa.

CONTROL

RJ45 Ethernet Connector

ALARMS

1 Alarm 1 Blue

2 Alarm 2 Violet

3 Alarm 3 Gray

4 Common White

POWER

1 Camera Power (24VAC) Red

2 Camera Power (24VAC) Orange

Captive

Screw

Open Screw

Slots

Cable

Ties

Complete the wiring to camera. Attach the camera assembly to the housing by sliding the (3)

open screw slots over the screws in the housing; tighten the fasteners on the bracket.

34

35

Page is loading ...

2539 Mounting Plate

Mounting Hole

Elmo PTC-201

(52

mm

) 2"

(13

mm

) ½"

Place the camera onto the quick release bracket using the (4) metric 3M Phillips head screws

provided. Place the screws on the spacers. Slide on the plate and camera then secure.

Captive

Screw

•

Coloque la cámara fotográfica sobre el soporte rápido del lanzamiento usando (4) los tornillos principales los 3M Phillips

métricos proporcionados. Coloque los tornillos en los espaciadores. Resbale en la placa y la cámara fotográfica entonces

seguras.

•

Placez l'appareil-photo sur la parenthèse rapide de dégagement à l'aide (4) des vis principales 3M Phillips métriques fournies.

Placez les vis sur les entretoises. Glissez du plat et de l'appareil-photo puis bloqués.

•

Setzen Sie die Kamera auf dem schnellen Freigabehaltewinkel mit den (4) metrischen 3M bereitgestellten Kreuzkopf-

hauptschrauben. Setzen Sie die Schrauben auf die Distanzscheiben. Schieben Sie auf die sichere Platte und die Kamera dann.

•

Coloque a câmera no suporte rápido da liberação usando (4) os parafusos principais 3M Phillips métricos fornecidos.

Coloque os parafusos nos espaçadores. Deslize na placa e na câmera então seguras.

•

Disponga la macchina fotografica sulla staffa rapida del rilascio per mezzo (4) delle viti cape "phillips" 3M metriche fornite.

Disponga le viti sui distanziatori. Faccia scorrere sulla piastra e sulla macchina fotografica allora sicure.

27

2539 Mounting Plate

Mounting Hole

Elmo PTC-400C

(52

mm

) 2"

(13

mm

) ½"

Attach quick release bracket to mounting plate using (4) #8 screws and star washer. Complete

assembly as shown, then secure camera to the quick release plate.

(26

mm

) 1"

• Una el soporte rápido del lanzamiento a la placa de montaje usando (4) los tornillos #8 y la arandela de la estrella.

Termine a asamblea como cámara fotográfica demostrada, después segura a la placa rápida del lanzamiento.

• Attachez la parenthèse rapide de dégagement au plat de support à l'aide (4) des vis #8 et tenez le premier rôle la

rondelle. Accomplissez l'assemblée en tant qu'appareil-photo montré et puis bloqué au plat rapide de dégagement.

• Bringen Sie schnellen Freigabehaltewinkel zur Montageplatte mit (4) Schrauben #8 und Sternunterlegscheibe an. Führen

Sie Versammlung als gezeigte, dann sichere Kamera zur schnellen Freigabeplatte durch.

• Una o suporte rápido da liberação à placa de montagem usando (4) os parafusos #8 e a arruela da estrela. Termine o

conjunto como a câmera mostrada, a seguir segura à placa rápida da liberação.

• Fissi la staffa rapida del rilascio al giunto di supporto usando (4) le viti #8 e la rondella della stella. Completi il complessivo

come macchina fotografica indicata e quindi sicura alla piastra rapida del rilascio.

Quick release

plate

45

46

Page is loading ...

34

2539 Mounting

Plate

Mounting Hole

Sony SNCRZ25

Attach bracket with (1) 1/4x20 bolt, washer and lock washer and (2) 3mm x 8mm Phillip head screws

and lockwashers. Place the screws on the spacers. Slide on the plate and camera then secure.

(26

mm

) 1"

• Instale la cámara fotográfica al soporte con (3) los tornillos, las tuercas y las arandelas principales el 8x32x.5"planos.

Coloque (3) 8x32x3/8"screws en los espaciadores. Resbale en la placa y la cámara fotográfica entonces seguras.

• Installez l'appareil-photo sur la parenthèse avec (3) les vis, les écrous et les rondelles principaux 8x32x.5"plats. Placez (3)

8x32x3/8"screws sur les entretoises. Glissez du plat et de l'appareil-photo puis bloqués.

• Bringen Sie Kamera zum Haltewinkel mit (3) 8x32x.5"flachen Hauptschrauben, Nüssen und Unterlegscheiben an. Setzen

Sie (3) 8x32x3/8"screws auf die Distanzscheiben. Schieben Sie auf die sichere Platte und die Kamera dann.

• Instale a câmera ao suporte com (3) os parafusos, as porcas e as arruelas principais 8x32x.5"lisos. Coloque (3) 8x32x3/8"

screws nos espaçadores. Deslize na placa e na câmera então seguras.

• Installi la macchina fotografica alla staffa con (3) le viti, i dadi e le rondelle capi piani 8x32x.5". Disponga (3) 8x32x3/8"

screws sui distanziatori. Faccia scorrere sulla piastra e sulla macchina fotografica allora sicure.

35

2539 Mounting

Plate

Mounting Hole

Sony SNCRZ30

Attach bracket with (1) 1/4x20 bolt, washer and lock washer. Place (3) 8x32x3/8”screws on the

spacers. Slide on the plate and camera then secure.

(52

mm

) 2"

• Una el soporte con (1) el perno 1/4x20, la arandela y la arandela de cerradura. Coloque (3) 8x32x3/8" screws en los

espaciadores. Resbale en la placa y la cámara fotográfica entonces seguras.

• Attachez la parenthèse avec (1) le boulon 1/4x20, la rondelle et la rondelle de freinage. Placez (3) 8x32x3/8" screws sur

les entretoises. Glissez du plat et de l'appareil-photo puis bloqués.

• Bringen Sie Haltewinkel mit (1) Schraubbolzen 1/4x20, Unterlegscheibe und Federring an. Setzen Sie (3) 8x32x3/8" screws

auf die Distanzscheiben. Schieben Sie auf die sichere Platte und die Kamera dann.

• Una o suporte com (1) parafuso 1/4x20, arruela e arruela de fechamento. Coloque (3) 8x32x3/8" screws nos espaça-

dores. Deslize na placa e na câmera então seguras.

• Fissi la staffa con (1) il bullone 1/4x20, la rondella e la ranella di bloccaggio. Disponga (3) 8x32x3/8" screws sui distanzia-

tori. Faccia scorrere sulla piastra e sulla macchina fotografica allora sicure.

53

54

Page is loading ...

18

12

21

22

15

14

16

17

28

8

26

27

29

30

25

20

9

11

13

19

10

24

23

7

6

5

4

3

2

1

Igloo Dome

Replacement Parts List

noitpircseD

rebmuNtraP

1 RPFD7501 TRIM RING FD75

2

RPGK3524

TRIM RING INSULATION

FD7T

TINTED REPLACEMENT CAPSULE

FD7C

CLEAR REPLACEMENT CAPSULE

4 RPFD703 DOME CLAMPING BRACKET

5

RPVL3414

CAMERA BRACKET

6

RPGK3521

HOUSING INSULATION

7

RPVL2593

HOUSING

8

RPVL3164

BOARD SHELF

9

RPGK3209

TOP INSULATION

10 RPFSSR06 STRAIN RELIEF CONNECTOR

11 RPFSRT20 NPT-3/8" NYLON LOCK NUT

12 RPVL3411 HEAT PUMP

13 RPVL3295 SUN SHIELD

14 RPVL3203 SIDE DOOR

15 RPVL3202 FILTER

16 RPGK3560 SIDE DOOR GASKET LEFT

17 RPVL3200 FILTER FLANGE

18 RPFSRT22 STRAIN RELIEF CONNECTOR

19 RPFSSR12 NYLON LOCK NUT

20 RP76VL2001 FLOW SENSOR

21 RPVL3566 RESERVOIR&PUMP ASSEMBLY

22 RPVL3552 FILTER FLANGE

23 RPGK3198 SIDE DOOR GASKET RIGHT

24 RPVL3180 SIDE DOOR RIGHT

25 RPVL3562 FLOW SENSOR SHIELD

26 RPCONN12 12 POS CONNECTOR

27 RPCONN15 15 POS CONNECTOR

28 RPGK3561 COVER GASKET

29 RPVL2003 CONNECTOR BOARD

30 RP70TRANS12 REPLACEMENT TRANSFORMER 96 VA

3

Igloo Dome

Replacement Parts List

31

34

35

33

36

37

38

39

37

32

31 RPVIMU3ES POWER SUPPLY

32 RPBLEH12 BLOWER 60 X 60 X 25

33 RPPLTCONT PELTIER DEVICE CONTROL BOARD

34 RPVL2004 CONTROL BOARD

35

RPZPSA6012

POWER SUPPLY

36

RPVLBL08

120X38mm FAN

37

RPGK3415

RADIATOR SEALING

38

RPIGRDTR

RADIATOR

39

RPVL3210

POLE MOUNT BRACKET

noitpircseD

rebmuNtraP

Product Registration/Warranty

Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you

with only the highest quality products available with unmatched customer service levels that are second-

to-none in the security industry.

Should a problem arise, rest assure that Videolarm stands behind its products

by offering some of the most impressive warranty plans available: 3 Years

on all Housings, Poles, Power Supplies, and Accessories and 5 Years on

all camera systems (SView, QView, Warriors), and InfraRed Illuminators.

Register Your Products

Option 1: Online Option 2: Mail-In

Take a few moments and validate your purchase with our Online Product Registration Form

at

www.videolarm.com/productregistration.jsp

or complete and mail-in the bottom portion of this yer.

Register your recent Videolarm purchases and benet from the following:

• Simple and Trouble-Free RMA process

• Added into customer database to receive product updates / news

• Eliminate the need to archive original purchase documents:

Receipts, Purchase Orders, etc…

Main Contact Info

First Name: Last Name:

Professional Title: Company:

Address 1: Address 2:

City: State / Province/Country:

Zip / Postal Code: Phone Number: E-mail Address:

Product Information

Please Circle One: Business Personal

Name & Location of Company / Store where Purchased:

(City, State, Country)

Videolarm Product ID Product Description

Serial #

(Available only for Camera Systems, IR Illuminators, Wireless Devices)

PO#

Cut at the dotted Line

Place in envelope, afx stamp and mail to: Videolarm ATTN: Warranty

2525 Park Central Ave.

Decatur, GA 30035

Moog Videolarm IGDW75CF1 Operating instructions

This manual is also suitable for

Moog Videolarm IGDW75CF1 Operating instructions

in other languages

Related papers

Other documents