Hitachi INVERTER L200 User manual

L200 Series Inverter

Instruction Manual

• Single-phase Input 200V Class

• Three-phase Input 200V Class

• Three-phase Input 400V Class

After reading this manual,

keep it handy for future reference.

Hitachi Industrial Equipment Systems Co., Ltd.

Manual Number: NB660XA

September 2004

Cover

L200 Inverter

i

Safety Messages

For the best results with the L200 Series inverter, carefully read this manual and all of

the warning labels attached to the inverter before installing and operating it, and follow

the instructions exactly. Keep this manual handy for quick reference.

Definitions and Symbols

A safety instruction (message) includes a “Safety Alert Symbol” and a signal word or

phrase such as WARNING or CAUTION. Each signal word has the following meaning:

HIGH VOLTAGE: This symbol indicates high voltage. It calls your attention to items

or operations that could be dangerous to you and other persons operation this equipment.

Read the message and follow the instructions carefully.

WARNING: Indicates a potentially hazardous situation that, if not avoided, can result in

serious injury or death.

CAUTION: Indicates a potentially hazardous situation that, if not avoided, can result in

minor to moderate injury, or serious damage to the product. The situation described in

the CAUTION may, if not avoided, lead to serious results. Important safety measures

are described in CAUTION (as well as WARNING), so be sure to observe them.

1 Step 1: Indicates a step in a series of action steps required to accomplish a goal. The

number of the step will be contained in the step symbol.

NOTE: Notes indicate an area or subject of special merit, emphasizing either the

product’s capabilities or common errors in operation or maintenance.

TIP: Tips give a special instruction that can save time or provide other benefits while

installing or using the product. The tip calls attention to an idea that may not be obvious

to first-time users of the product.

Hazardous High Voltage

HIGH VOLTAGE: Motor control equipment and electronic controllers are connected to

hazardous line voltages. When servicing drives and electronic controllers, there may be

exposed components with housings or protrusions at or above line potential. Extreme

care should be taken to protect against shock.

Stand on an insulating pad and make it a habit to use only one hand when checking com-

ponents. Always work with another person in case an emergency occurs. Disconnect

power before checking controllers or performing maintenance. Be sure equipment is

properly grounded. Wear safety glasses whenever working on electronic controllers or

rotating machinery.

ii

General Precautions - Read These First!

WARNING: This equipment should be installed, adjusted, and serviced by qualified

electrical maintenance personnel familiar with the construction and operation of the

equipment and the hazards involved. Failure to observe this precaution could result in

bodily injury.

WARNING: The user is responsible for ensuring that all driven machinery, drive train

mechanism not supplied by Hitachi Industrial Equipment Systems Co., Ltd., and process

line material are capable of safe operation at an applied frequency of 150% of the

maximum selected frequency range to the AC motor. Failure to do so can result in

destruction of equipment and injury to personnel should a single-point failure occur.

WARNING: For equipment protection, install a ground leakage type breaker with a fast

response circuit capable of handling large currents. The ground fault protection circuit is

not designed to protect against personal injury.

WARNING: HAZARD OF ELECTRICAL SHOCK. DISCONNECT INCOMING

POWER BEFORE WORKING ON THIS CONTROL.

WARNING: Wait at least five (5) minutes after turning OFF the input power supply

before performing maintenance or an inspection. Otherwise, there is the danger of

electric shock.

CAUTION: These instructions should be read and clearly understood before working

on L200 series equipment.

CAUTION: Proper grounds, disconnecting devices and other safety devices and their

location are the responsibility of the user and are not provided by Hitachi Industrial

Equipment Systems Co., Ltd.

CAUTION: Be sure to connect a motor thermal disconnect switch or overload device to

the L200 series controller to assure that the inverter will shut down in the event of an

overload or an overheated motor.

HIGH VOLTAGE: Dangerous voltage exists until power light is OFF. Wait at least five

(5) minutes after input power is disconnected before performing maintenance.

WARNING: This equipment has high leakage current and must be permanently (fixed)

hard-wired to earth ground via two independent cables.

L200 Inverter

iii

WARNING: Rotating shafts and above-ground electrical potentials can be hazardous.

Therefore, it is strongly recommended that all electrical work conform to the National

Electrical Codes and local regulations. Installation, alignment and maintenance should

be performed only by qualified personnel.

Factory-recommended test procedures included in the instruction manual should be

followed. Always disconnect electrical power before working on the unit.

CAUTION:

a) Class I motor must be connected to earth ground via low resistive path (< 0.1Ω)

b) Any motor used must be of a suitable rating.

c) Motors may have hazardous moving parts. In this event suitable protection must

be provided.

CAUTION: Alarm connection may contain hazardous live voltage even when inverter is

disconnected. When removing the front cover for maintenance or inspection, confirm

that incoming power for alarm connection is completely disconnected.

CAUTION: Hazardous (main) terminals for any interconnection (motor, contact

breaker, filter, etc.) must be inaccessible in the final installation.

CAUTION: This equipment should be installed in IP54 or equivalent (see EN60529)

enclosure. The end application must be in accordance with BS EN60204-1. Refer to the

section “

Choosing a Mounting Location” on page 2–9. The diagram dimensions are to

be suitably amended for your application.

CAUTION: Connection to field wiring terminals must be reliably fixed having two

independent means of mechanical support. Use a termination with cable support (figure

below), or strain relief, cable clamp, etc.

CAUTION: A double-pole disconnection device must be fitted to the incoming main

power supply close to the inverter. Additionally, a protection device meeting IEC947-1/

IEC947-3 must be fitted at this point (protection device data shown in “

Determining

Wire and Fuse Sizes” on page 2–16).

NOTE: The above instructions, together with any other requirements highlighted in this

manual, must be followed for continued LVD (European Low Voltage Directive)

compliance.

Terminal (ring lug) Cable support

Cable

iv

Index to Warnings and Cautions in This Manual

Cautions and Warnings for Orientation and Mounting Procedures

Wiring - Warnings for Electrical Practices and Wire Specifications

CAUTION: Hazard of electrical shock. Disconnect incoming power

before working on this control. Wait five (5) minutes before removing the

front cover.

....... 2–3

CAUTION: Be sure to install the unit on flame-resistant material such as

a steel plate. Otherwise, there is the danger of fire.

....... 2–9

CAUTION: Be sure not to place any flammable materials near the

inverter. Otherwise, there is the danger of fire.

....... 2–9

CAUTION: Be sure not to let the foreign matter enter vent openings in

the inverter housing, such as wire clippings, spatter from welding, metal

shavings, dust, etc. Otherwise, there is the danger of fire.

....... 2–9

CAUTION: Be sure to install the inverter in a place that can bear the

weight according to the specifications in the text (Chapter 1, Specifica-

tions Tables). Otherwise, it may fall and cause injury to personnel.

....... 2–9

CAUTION: Be sure to install the unit on a perpendicular wall that is not

subject to vibration. Otherwise, it may fall and cause injury to personnel.

....... 2–9

CAUTION: Be sure not to install or operate an inverter that is damaged

or has missing parts. Otherwise, it may cause injury to personnel.

....... 2–9

CAUTION: Be sure to install the inverter in a well-ventilated room that

does not have direct exposure to sunlight, a tendency for high tempera-

ture, high humidity or dew condensation, high levels of dust, corrosive

gas, explosive gas, inflammable gas, grinding-fluid mist, salt damage,

etc. Otherwise, there is the danger of fire.

....... 2–9

CAUTION: Be sure to maintain the specified clearance area around the

inverter and to provide adequate ventilation. Otherwise, the inverter may

overheat and cause equipment damage or fire.

..... 2–10

WARNING: “Use 60/75°C Cu wire only” or equivalent. ..... 2–15

WARNING: “Open Type Equipment.” ..... 2–15

WARNING: “Suitable for use on a circuit capable of delivering not more

than 5,000 rms symmetrical amperes, 240 V maximum.” For models with

suffix N or L.

..... 2–15

L200 Inverter

v

Wiring - Cautions for Electrical Practices

WARNING: “Suitable for use on a circuit capable of delivering not more

than 5,000 rms symmetrical amperes, 480 V maximum.” For models with

suffix H.

.... 2–15

HIGH VOLTAGE: Be sure to ground the unit. Otherwise, there is a

danger of electric shock and/or fire.

.... 2–15

HIGH VOLTAGE: Wiring work shall be carried out only by qualified

personnel. Otherwise, there is a danger of electric shock and/or fire.

.... 2–15

HIGH VOLTAGE: Implement wiring after checking that the power

supply is OFF. Otherwise, you may incur electric shock and/or fire.

.... 2–15

HIGH VOLTAGE: Do not connect wiring to an inverter or operate an

inverter that is not mounted according the instructions given in this

manual. Otherwise, there is a danger of electric shock and/or injury to

personnel.

.... 2–15

WARNING: Make sure the input power to the inverter is OFF. If the drive

has been powered, leave it OFF for five minutes before continuing.

.... 2–21

CAUTION: Fasten the screws with the specified fastening torque in the

table below. Check for any loosening of screws. Otherwise, there is the

danger of fire.

.... 2–17

CAUTION: Be sure that the input voltage matches the inverter specifica-

tions: • Single/Three phase 200 to 240 V 50/60 Hz (up to 2.2kW) for

NFEF/NFU models • Three phase 200 to 240V 50/60Hz (above 2.2kW)

for LFU models • Three phase 380 to 480 V 50/60Hz for HFEF models

.... 2–18

CAUTION: Be sure not to power a three-phase-only inverter with single

phase power. Otherwise, there is the possibility of damage to the inverter

and the danger of fire.

.... 2–18

CAUTION: Be sure not to connect an AC power supply to the output

terminals. Otherwise, there is the possibility of damage to the inverter

and the danger of injury and/or fire.

.... 2–19

Power Input Output to Motor

L200 Inverter

vi

Powerup Test Caution Messages

CAUTION: Remarks for using ground fault interrupter breakers in the

main power supply: Adjustable frequency inverters with CE-filters (RFI-

filter) and shielded (screened) motor cables have a higher leakage current

toward Earth GND. Especially at the moment of switching ON this can

cause an inadvertent trip of ground fault interrupters. Because of the

rectifier on the input side of the inverter there is the possibility to stall the

switch-off function through small amounts of DC current. Please observe

the following: • Use only short time-invariant and pulse current-sensitive

ground fault interrupters with higher trigger current. • Other components

should be secured with separate ground fault interrupters. • Ground fault

interrupters in the power input wiring of an inverter are not an absolute

protection against electric shock.

..... 2–19

CAUTION: Be sure to install a fuse in each phase of the main power

supply to the inverter. Otherwise, there is the danger of fire.

..... 2–19

CAUTION: For motor leads, ground fault interrupter breakers and

electromagnetic contactors, be sure to size these components properly

(each must have the capacity for rated current and voltage). Otherwise,

there is the danger of fire.

..... 2–19

CAUTION: The heat sink fins will have a high temperature. Be careful

not to touch them. Otherwise, there is the danger of getting burned.

..... 2–22

CAUTION: The operation of the inverter can be easily changed from low

speed to high speed. Be sure to check the capability and limitations of the

motor and machine before operating the inverter. Otherwise, there is the

danger of injury.

..... 2–22

CAUTION: If you operate a motor at a frequency higher than the inverter

standard default setting (50Hz/60Hz), be sure to check the motor and

machine specifications with the respective manufacturer. Only operate

the motor at elevated frequencies after getting their approval. Otherwise,

there is the danger of equipment damage and/or injury.

.... 2–22,

..... 2–28

CAUTION: Check the following before and during the powerup test.

Otherwise, there is the danger of equipment damage. • Is the shorting bar

between the [+1] and [+] terminals installed? DO NOT power or operate

the inverter if the jumper is removed. • Is the direction of the motor

rotation correct? • Did the inverter trip during acceleration or decelera-

tion? • Were the rpm and frequency meter readings as expected? • Were

there any abnormal motor vibrations or noise?

..... 2–22

L200 Inverter

vii

Warnings for Configuring Drive Parameters

Cautions for Configuring Drive Parameters

Warnings for Operations and Monitoring

WARNING: When parameter B012, level of electronic thermal setting, is

set to motor FLA rating (Full Load Ampere nameplate rating), the

inverter provides solid state motor overload protection at 115% of motor

FLA or equivalent. If parameter B012 exceeds the motor FLA rating, the

motor may overheat and be damaged. Parameter B012, level of electronic

thermal setting, is a variable parameter.

.... 3–33

CAUTION: Be careful to avoid specifying a braking time that is long

enough to cause motor overheating. If you use DC braking, we recom-

mend using a motor with a built-in thermistor, and wiring it to the

inverter’s thermistor input (see “Thermistor Thermal Protection” on

page 4–25). Also refer to the motor manufacturer’s specifications for

duty-cycle recommendations during DC braking.

.... 3–20

WARNING: Be sure to turn ON the input power supply only after closing

the front case. While the inverter is energized, be sure not to open the

front case. Otherwise, there is the danger of electric shock.

...... 4–3

WARNING: Be sure not to operate electrical equipment with wet hands.

Otherwise, there is the danger of electric shock.

...... 4–3

WARNING: While the inverter is energized, be sure not to touch the

inverter terminals even when the motor is stopped. Otherwise, there is the

danger of electric shock.

...... 4–3

WARNING: If the Retry Mode is selected, the motor may suddenly

restart after a trip stop. Be sure to stop the inverter before approaching the

machine (be sure to design the machine so that safety for personnel is

secure even if it restarts.) Otherwise, it may cause injury to personnel.

...... 4–3

WARNING: If the power supply is cut OFF for a short period of time, the

inverter may restart operation after the power supply recovers if the Run

command is active. If a restart may pose danger to personnel, so be sure

to use a lock-out circuit so that it will not restart after power recovery.

Otherwise, it may cause injury to personnel.

...... 4–3

WARNING: The Stop Key is effective only when the Stop function is

enabled. Be sure to enable the Stop Key separately from the emergency

stop. Otherwise, it may cause injury to personnel.

...... 4–3

WARNING: During a trip event, if the alarm reset is applied and the Run

command is present, the inverter will automatically restart. Be sure to

apply the alarm reset only after verifying the Run command is OFF.

Otherwise, it may cause injury to personnel.

...... 4–3

viii

Cautions for Operations and Monitoring

WARNING: Be sure not to touch the inside of the energized inverter or to

put any conductive object into it. Otherwise, there is a danger of electric

shock and/or fire.

....... 4–3

WARNING: If power is turned ON when the Run command is already

active, the motor will automatically start and injury may result. Before

turning ON the power, confirm that the RUN command is not present.

....... 4–3

WARNING: When the Stop key function is disabled, pressing the Stop

key does not stop the inverter, nor will it reset a trip alarm.

....... 4–3

WARNING: Be sure to provide a separate, hard-wired emergency stop

switch when the application warrants it.

....... 4–3

WARNING: If the power is turned ON and the Run command is already

active, the motor starts rotation and is dangerous! Before turning power

ON, confirm that the Run command is not active.

..... 4–12

WARNING: After the Reset command is given and the alarm reset

occurs, the motor will restart suddenly if the Run command is already

active. Be sure to set the alarm reset after verifying that the Run

command is OFF to prevent injury to personnel.

..... 4–24

CAUTION: The heat sink fins will have a high temperature. Be careful

not to touch them. Otherwise, there is the danger of getting burned.

....... 4–2

CAUTION: The operation of the inverter can be easily changed from low

speed to high speed. Be sure check the capability and limitations of the

motor and machine before operating the inverter. Otherwise, it may cause

injury to personnel.

....... 4–2

CAUTION: If you operate a motor at a frequency higher than the inverter

standard default setting (50Hz/60Hz), be sure to check the motor and

machine specifications with the respective manufacturer. Only operate

the motor at elevated frequencies after getting their approval. Otherwise,

there is the danger of equipment damage.

....... 4–2

CAUTION: It is possible to damage the inverter or other devices if your

application exceeds the maximum current or voltage characteristics of a

connection point.

....... 4–4

CAUTION: Be sure to turn OFF power to the inverter before changing

the SR/SK switch position. Otherwise, damage to the inverter circuitry

may occur.

....... 4–9

CAUTION: Be careful not to turn PID Clear ON and reset the integrator

sum when the inverter is in Run Mode (output to motor is ON). Other-

wise, this could cause the motor to decelerate rapidly, resulting in a trip.

..... 4–28

L200 Inverter

ix

Warnings and Cautions for Troubleshooting and Maintenance

General Warnings and Cautions

WARNING: Never modify the unit. Otherwise, there is a danger of electric shock and/

or injury.

CAUTION: Withstand voltage tests and insulation resistance tests (HIPOT) are

executed before the units are shipped, so there is no need to conduct these tests before

operation.

CAUTION: Do not attach or remove wiring or connectors when power is applied. Also,

do not check signals during operation.

CAUTION: Be sure to connect the grounding terminal to earth ground.

CAUTION: When inspecting the unit, be sure to wait five minutes after tuning OFF the

power supply before opening the cover.

WARNING: Wait at least five (5) minutes after turning OFF the input

power supply before performing maintenance or an inspection. Other-

wise, there is the danger of electric shock.

...... 6–2

WARNING: Make sure that only qualified personnel will perform

maintenance, inspection, and part replacement. Before starting to work,

remove any metallic objects from your person (wristwatch, bracelet,

etc.). Be sure to use tools with insulated handles. Otherwise, there is a

danger of electric shock and/or injury to personnel.

...... 6–2

WARNING: Never remove connectors by pulling on its wire leads (wires

for cooling fan and logic P.C.board). Otherwise, there is a danger of fire

due to wire breakage and/or injury to personnel.

...... 6–2

CAUTION: Do not connect the megger to any control circuit terminals

such as intelligent I/O, analog terminals, etc. Doing so could cause

damage to the inverter.

.... 6–10

CAUTION: Never test the withstand voltage (HIPOT) on the inverter.

The inverter has a surge protector between the main circuit terminals

above and the chassis ground.

.... 6–10

HIGH VOLTAGE: Be careful not to touch wiring or connector terminals

when working with the inverters and taking measurements. Be sure to

place the measurement circuitry components above in an insulated

housing before using them.

.... 6–14

x

CAUTION: Do not stop operation by switching OFF electromagnetic contactors on the

primary or secondary sides of the inverter.

When there has been a sudden power failure while an operation instruction is active, then

the unit may restart operation automatically after the power failure has ended. If there is

a possibility that such an occurrence may harm humans, then install an electromagnetic

contactor (Mgo) on the power supply side, so that the circuit does not allow automatic

restarting after the power supply recovers. If the optional remote operator is used and the

retry function has been selected, this will also cause automatic restarting when a Run

command is active. So, please be careful.

CAUTION: Do not insert leading power factor capacitors or surge absorbers between

the output terminals of the inverter and motor.

CAUTION: MOTOR TERMINAL SURGE VOLTAGE SUPPRESSION FILTER

(For the 400 V CLASS)

In a system using an inverter with the voltage control PWM system, a voltage surge

caused by the cable constants such as the cable length (especially when the distance

between the motor and inverter is 10 m or more) and cabling method may occur at the

motor terminals. A dedicated filter of the 400 V class for suppressing this voltage surge

is available. Be sure to install a filter in this situation.

Power

Input

Inverter

L1, L2, L3

Ground fault

interrupter

U, V, W

Motor

PCS

FW

Power

Input

Inverter

L1, L2, L3

Ground fault

interrupter

U, V, W

Motor

GND lug

Surge absorber

Leading power

factor capacitor

L200 Inverter

xi

CAUTION: EFFECTS OF POWER DISTRIBUTION SYSTEM ON INVERTER

In the cases below involving a general-purpose inverter, a large peak current can flow on

the power supply side, sometimes destroying the converter module:

1. The unbalance factor of the power supply is 3% or higher.

2. The power supply capacity is at least 10 times greater than the inverter capacity (or

the power supply capacity is 500 kVA or more).

3. Abrupt power supply changes are expected, due to conditions such as:

a. Several inverters are interconnected with a short bus.

b. A thyristor converter and an inverter are interconnected with a short bus.

c. An installed phase advance capacitor opens and closes.

Where these conditions exist or when the connected equipment must be highly reliable,

you MUST install an input-side AC reactor of 3% (at a voltage drop at rated current)

with respect to the supply voltage on the power supply side. Also, where the effects of an

indirect lightning strike are possible, install a lightning conductor.

CAUTION: SUPPRESSION FOR NOISE INTERFERENCE FROM INVERTER

The inverter uses many semiconductor switching elements such as transistors and

IGBTs. Thus, a radio receiver or measuring instrument located near the inverter is

susceptible to noise interference.

To protect the instruments from erroneous operation due to noise interference, they

should be used well away from the inverter. It is also effective to shield the whole

inverter structure.

The addition of an EMI filter on the input side of the inverter also reduces the effect of

noise from the commercial power line on external devices.

Note that the external dispersion of noise from the power line can be minimized by

connecting an EMI filter on the primary side of inverter.

R1

S1

T1

R2

S2

T2

L1

L2

L3

U

V

W

EMI Filter Inverter

Motor

EMI Filter

Inverter

noise

Motor

Remote

Operator

Completely ground the

enclosed panel, metal

screen, etc. with as

short a wire as possible.

Grounded frame

Conduit or shielded

cable—to be grounded

xii

CAUTION: When the EEPROM error E08 occurs, be sure to confirm the setting values

again.

CAUTION: When using normally closed active state settings (C011 to C015) for exter-

nally commanded Forward or Reverse terminals [FW] or [RV], the inverter may start

automatically when the external system is powered OFF or disconnected from the

inverter! So, do not use normally closed active state settings for Forward or Reverse

terminals [FW] or [RV] unless your system design protects against unintended motor

operation.

CAUTION: In all the illustrations in this manual, covers and safety devices are

occasionally removed to describe the details. While operating the product, make sure

that the covers and safety devices are placed as they were specified originally and

operate it according to the instruction manual.

UL

®

Cautions, Warnings, and Instructions

Wiring Warnings for Electrical Practices and Wire Sizes

The Warnings and instructions in this section summarize the procedures necessary to

ensure an inverter installation complies with Underwriters Laboratories

®

guidelines.

WARNING: “Use 60/75°C Cu wire only” or equivalent.

WARNING: “Open Type Equipment.”

WARNING: “Suitable for use on a circuit capable of delivering not more than 5,000

rms symmetrical amperes, 240 V maximum.” For models with suffix N or L.

WARNING: “Suitable for use on a circuit capable of delivering not more than 5,000

rms symmetrical amperes, 480 V maximum.” For models with suffix H.

WARNING: “Hot surface—risk of burn.”

WARNING: “Install device in pollution degree 2 environment.”

WARNING: “Risk of electric shock—capacitor discharge time is at least 5 minutes.”

WARNING: “Solid state motor overload protection is provided in each model.”

L200 Inverter

xiii

Terminal Tightening Torque and Wire Size

The wire size range and tightening torque for field wiring terminals are presented in the

tables below.

Wire Connectors

WARNING: Field wiring connections must be

made by a UL Listed and CSA Certified ring lug

terminal connector sized for the wire gauge being

used. The connector must be fixed using the

crimping tool specified by the connector

manufacturer.

Input

Voltage

Motor Output

Inverter Model

Power Terminal

Wiring Size

Range (AWG)

Torque

kW HP ft-lbs (N-m)

200V

0.2 1/4 L200-002NFEF/NFU

16 0.6 0.80.4 1/2 L200-004NFEF/NFU

0.55 3/4 L200-005NFEF

0.75 1 L200-007NFEF/NFU

14

0.9 1.2

1.1 1 1/2 L200-011NFEF

1.5 2 L200-015NFEF/NFU 12

2.2 3 L200-022NFEF/NFU 10

3.7 5 L200-037LFU 12

5.5 7 1/2 L200-055LFU 10

1.5 2.0

7.5 10 L200-075LFU 8

400V

0.4 1/2 L200-004HFEF/HFU

16

0.9 1.2

0.75 1 L200-007HFEF/HFU

1.5 2 L200-015HFEF/HFU

2.2 3 L200-022HFEF/HFU

3.0 4 L200-030HFEF

14

4.0 5 L200-040HFEF/HFU

5.5 7 1/2 L200-055HFEF/HFU

12 1.5 2.0

7.5 10 L200-075HFEF/HFU

Terminal Connector

Wiring Size

Range (AWG)

Torque

ft-lbs (N-m)

Logic/Analog connector 30—16 0.16—0.19 0.22—0.25

Relay connector 30—14 0.37—0.44 0.5—0.6

Cable

Terminal (ring lug)

Cable support

xiv

Circuit Breaker and Fuse Sizes

The inverter’s connections to input power must include UL Listed inverse time circuit

breakers with 600V rating, or UL Listed fuses as shown in the table below.

Motor Overload Protection

Hitachi L200 inverters provide solid state motor overload protection, which depends on

the proper setting of the following parameters:

• B012 “electronic overload protection”

• B212 “electronic overload protection, 2nd motor”

Set the rated current [Amperes] of the motor(s) with the above parameters. The setting

range is 0.2 * rated current to 1.2 * rated current.

WARNING: When two or more motors are connected to the inverter, they cannot be

protected by the electronic overload protection. Install an external thermal relay on each

motor.

Input

Voltage

Motor Output

Inverter Model

Fuse (A)

(UL-rated,

class J, 600V)

kW HP

200V

0.2 1/4 L200-002NFEF/NFU 10

0.4 1/2 L200-004NFEF/NFU 10

0.55 3/4 L200-005NFEF 10

0.75 1 L200-007NFEF/NFU 15

1.1 1 1/2 L200-011NFEF 15

1.5 2 L200-015NFEF/NFU 20 (single ph.)

15 (three ph.)

2.2 3 L200-022NFEF/NFU 30 (single ph.)

20 (three ph.)

3.7 5 L200-037LFU 30

5.5 7 1/2 L200-055LFU 40

7.5 10 L200-075LFU 50

400V

0.4 1/2 L200-004HFEF/HFU 3

0.75 1 L200-007HFEF/HFU 6

1.5 2 L200-015HFEF/HFU 10

2.2 3 L200-022HFEF/HFU 10

3.0 4 L200-030HFEF 15

4.0 5 L200-040HFEF/HFU 15

5.5 7 1/2 L200-055HFEF/HFU 20

7.5 10 L200-075HFEF/HFU 25

xv

L200 Inverter

Safety Messages

Hazardous High Voltage i

General Precautions - Read These First! ii

Index to Warnings and Cautions in This Manual iv

General Warnings and Cautions ix

UL® Cautions, Warnings, and Instructions xii

Table of Contents

Revisions xvii

Contact Information xviii

Chapter 1: Getting Started

Introduction 1–2

L200 Inverter Specifications 1–5

Introduction to Variable-Frequency Drives 1–12

Frequently Asked Questions 1–17

Chapter 2: Inverter Mounting and Installation

Orientation to Inverter Features 2–2

Basic System Description 2–7

Step-by-Step Basic Installation 2–8

Powerup Test 2–21

Using the Front Panel Keypad 2–23

Chapter 3: Configuring Drive Parameters

Choosing a Programming Device 3–2

Using Keypad Devices 3–3

“D” Group: Monitoring Functions 3–6

“F” Group: Main Profile Parameters 3–9

“A” Group: Standard Functions 3–10

“B” Group: Fine Tuning Functions 3–31

“C” Group: Intelligent Terminal Functions 3–42

“H” Group: Motor Constants Functions 3–56

Table of Contents

xvi

Chapter 4: Operations and Monitoring

Introduction 4–2

Connecting to PLCs and Other Devices 4–4

Control Logic Signal Specifications 4–6

Intelligent Terminal Listing 4–7

Using Intelligent Input Terminals 4–9

Using Intelligent Output Terminals 4–34

Analog Input Operation 4–51

Analog Output Operation 4–53

PID Loop Operation 4–54

Configuring the Inverter for Multiple Motors 4–56

Chapter 5: Inverter System Accessories

Introduction 5–2

Component Descriptions 5–3

Dynamic Braking 5–5

Chapter 6: Troubleshooting and Maintenance

Troubleshooting 6–2

Monitoring Trip Events, History, & Conditions 6–5

Restoring Factory Default Settings 6–8

Maintenance and Inspection 6–9

Warranty 6–16

Appendix A: Glossary and Bibliography

Glossary A–2

Bibliography A–8

Appendix B: ModBus Network Communications

Introduction B–2

Connecting the Inverter to ModBus B–3

Network Protocol Reference B–6

ModBus Data Listing B–19

Appendix C: Drive Parameter Settings Tables

Introduction C–2

Parameter Settings for Keypad Entry C–2

Appendix D: CE–EMC Installation Guidelines

CE–EMC Installation Guidelines D–2

Hitachi EMC Recommendations D–6

Index

L200 Inverter

xvii

Revisions

Revision History Table

No. Revision Comments Date of Issue

Operation

Manual No.

Initial release of manual NB660X March 2004 NB660X

1 Revision A

Pages 3–37 to 3–39, B–33 – Added B032 description,

made Index entries

April 2004 NB660XA

xviii

Contact Information

NOTE: To receive technical support for the Hitachi inverter you purchased, contact the

Hitachi inverter dealer from whom you purchased the unit, or the sales office or factory

contact listed above. Please be prepared to provide the following inverter nameplate

information:

1. Model

2. Date of purchase

3. Manufacturing number (MFG No.)

4. Symptoms of any inverter problem

If any inverter nameplate information is illegible, please provide your Hitachi contact

with any other legible nameplate items. To reduce unpredictable downtime, we recom-

mend that you stock a spare inverter.

Hitachi America, Ltd.

Power and Industrial Division

50 Prospect Avenue

Tarrytown, NY 10591

U.S.A.

Phone: +1-914-631-0600

Fax: +1-914-631-3672

Hitachi Australia Ltd.

Level 3, 82 Waterloo Road

North Ryde, N.S.W. 2113

Australia

Phone: +61-2-9888-4100

Fax: +61-2-9888-4188

Hitachi Europe GmbH

Am Seestern 18

D-40547 Düsseldorf

Germany

Phone: +49-211-5283-0

Fax: +49-211-5283-649

Hitachi Industrial Equipment Systems Co, Ltd.

International Sales Department

WBG MARIVE WEST 16F

6, Nakase 2-chome

Mihama-ku, Chiba-shi,

Chiba 261-7116 Japan

Phone: +81-43-390-3516

Fax: +81-43-390-3810

Hitachi Asia Ltd.

16 Collyer Quay

#20-00 Hitachi Tower, Singapore 049318

Singapore

Phone: +65-538-6511

Fax: +65-538-9011

Hitachi Industrial Equipment Systems Co, Ltd.

Narashino Division

1-1, Higashi-Narashino 7-chome

Narashino-shi, Chiba 275-8611

Japan

Phone: +81-47-474-9921

Fax: +81-47-476-9517

Hitachi Asia (Hong Kong) Ltd.

7th Floor, North Tower

World Finance Centre, Harbour City

Canton Road, Tsimshatsui, Kowloon

Hong Kong

Phone: +852-2735-9218

Fax: +852-2735-6793

Page is loading ...

Hitachi INVERTER L200 User manual

This manual is also suitable for

Hitachi INVERTER L200 User manual

Related papers

Other documents