Behringer DDM 4000 Bundle II User manual

Brand: Behringer

Model: DDM 4000 Bundle II

Category: DJ controllers

Type: User manual

This manual is also suitable for

DIGITAL PRO MIXER DDM4000

User Manual

A50-16713-00001

DIGITAL PRO MIXER DDM4000

Important Safety Instructions

Caution

To reduce the risk of electric shock, do not remove the +

top cover (or the rear section). No user serviceable parts

inside. Refer servicing to quali ed personnel.

To reduce the risk of  re or electric shock, do not expose +

this appliance to rain and moisture. The apparatus shall

not be exposed to dripping or splashing liquids and no

objects  lled with liquids, such as vases, shall be placed

on the apparatus.

This symbol, wherever it appears, alerts you to the

presence of uninsulated dangerous voltage inside

the enclosure - voltage that may be suf cient to

constitute a risk of shock.

This symbol, wherever it appears, alerts you to

important operating and maintenance instructions

in the accompanying literature. Please read the

manual.

Read these instructions.1)

Keep these instructions.2)

Heed all warnings.3)

Follow all instructions.4)

Do not use this apparatus near water.5)

Clean only with dry cloth.6)

Do not block any ventilation openings. Install in accor-7)

dance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, 8)

heat registers, stoves, or other apparatus (including

ampli ers) that produce heat.

Do not defeat the safety purpose of the polarized or 9)

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding-type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided

plug does not  t into your outlet, consult an electrician

for replacement of the obsolete outlet.

Place the power cord so that it is protected from being 10)

walked on and sharp edges. Be sure that the power cord is

protected particularly at plugs, convenience receptacles

and the point where it exits from the apparatus.

The apparatus shall be connected to a MAINS socket 11)

outlet with a protective earthing connection.

Where the MAINS plug or an appliance coupler is used 12)

as the disconnect device, the disconnect device shall

remain readily operable.

Only use attachments/accessories specified by the 13)

manufacturer.

Use only with the cart, stand, tripod, bracket, or table 14)

speci ed by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when 15)

unused for long periods of time.

Refer all servicing to quali ed service personnel. Servic-16)

ing is required when the apparatus has been damaged in

any way, such as power supply cord or plug is damaged,

liquid has been spilled or objects have fallen into the appa-

ratus, the apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

Caution

These service instructions are for use by quali ed ser- +

vice personnel only. To reduce the risk of electric shock

do not perform any servicing other than that contained in

the operation instructions. Repairs have to be performed

by quali ed service personnel.

DIGITAL PRO MIXER DDM4000

DDM4000

DIGITAL PRO MIXER

Ultimate 5-Channel Digital DJ Mixer with Sampler, 4 FX Sections, Dual BPM Counters and MIDI

32-bit digital DJ mixer with beat-synchronized sampler, 4 multi-FX sections, 2 patented =

BPM coun-

ters, digital crossfader and MIDI

4 Phono/Line stereo channels allowing max. 8 signal sources to be connected simultaneously =

2 Microphone inputs with Gain, EQ, Talk function and FX =

4 stereo channels with Gain, programmable parametric 3-band EQ with Kill function, fader curve =

control and exible crossfader assignment

Fully featured MIDI controller for your DJ software =

Sophisticated sampler with beat-controlled loop function, real-time pitch control, sampler FX and =

crossfader start option

2 freely assignable and BPM-synchronized, high-quality FX engines (Bitcrusher, Resonator, Reverb, =

Flanger, etc.)

Ultra-fast, accurate and patented BPM counters for automatic BPM synchronization of sampler, FX, =

crossfader and external drum machines, etc. via MIDI

Digital crossfader with exible curve adjustment, reverse button and automatic, BPM-synchronized =

crossfading

Dual-mode crossfader with innovative frequency-selective crossfading =

Dedicated Headphone section includes PFL Mix/Split and Bass/Snare boost functions =

Recall your last mixer setting at the push of a button =

Digital S/PDIF output for direct recording of your performance =

Rack mount brackets included for ultimate exibility =

High-quality components and exceptionally rugged construction ensure long life =

Conceived and designed by BEHRINGER Germany =

1) U.S. Patent No.: 6812394 / German Patent No.: 102 23 735

DIGITAL PRO MIXER DDM4000

Foreword

Dear Customer,

Welcome to the team of

BEHRINGER users, and

thank you very much for

expressing your confi-

dence in us by purchasing

this device.

Writing this foreword

for you gives me great

pleasure, because it re-

presents the culmination

of many months of hard

work delivered by our en-

gineering team to achieve

a very ambitious goal: to

design a digital DJ mixer

that offers a maximum of

performance thanks to its

one-of-a-kind functions

and intuitive control. The

task of designing our new

DDM4000 certainly meant

a great deal of responsibility, which we assumed by focusing on

you, the discerning user and musician. Meeting your expectations

also meant a lot of work and night shifts. But it was fun, too. De-

veloping a product usually brings a lot of people together. What a

great feeling it is when all who participated in such a project can

be proud of what they’ve achieved.

It is our philosophy to share our enjoyment with you, because you

are the most important member of the BEHRINGER team. With

your highly competent suggestions for new products you’ve made

a signicant contribution to shaping our company and making it

successful. In return, we guarantee you uncompromising quality

as well as excellent technical and audio properties at an extremely

reasonable price. All of this will enable you to give free rein to your

creativity without being hampered by budget constraints.

We are often asked how we manage to produce such high-quality

devices at such unbelievably low prices. The answer is quite

simple: it’s you, our customers! Many satised customers mean

large sales volumes, enabling us to get better purchasing terms

for components, etc. Isn’t it only fair to pass this benet on to you?

Because we know that your success is our success, too!

I would like to thank everyone who has made the DDM4000 pos-

sible. You have all made your own personal contributions, from

the developers and the many other employees at this company,

to you, the BEHRINGER user.

My friends, it’s been worth the effort!

Thank you very much,

Uli Behringer

Table of contents

1. Introduction ......................................................................... 5

1.1 Before you get started .................................................. 5

1.1.1 Shipment ............................................................. 5

1.1.2 Initial operation ................................................... 5

1.1.3 Online registration ............................................... 5

2. Controls and connections ................................................. 6

2.1 Stereo channels 1 – 4 .................................................. 7

2.2 Microphone channel ..................................................... 7

2.3 Crossfader section ....................................................... 8

2.4 Main and Phones section ............................................. 9

2.5 BPM and Effects section .............................................. 9

2.6 Sampler ...................................................................... 10

2.7 Rear panel connectors ............................................... 10

2.8 Rear panel outputs ......................................................11

2.9 Power section ..............................................................11

2.10 Hookup example ...................................................... 12

3. Operation........................................................................... 13

3.1 Console Setup ............................................................ 13

3.1.1 Selection lists on screen ................................... 13

3.2 Using stereo channels ................................................ 13

3.2.1 EQ modes: SINGLE and MULTI ....................... 13

3.2.2 Channel Setup .................................................. 14

3.3 Operating the Microphone channel ............................ 14

3.3.1 Mic Setup .......................................................... 14

3.3.2 Talk Setup ......................................................... 16

3.4 Operating the crossfader ............................................ 16

3.4.1 Crossfader modes: KILL and X-OVER ............. 16

3.4.2 Crossfader Setup .............................................. 16

3.4.3 Bounce to MIDI Clock ....................................... 16

3.5 Operating the Main section ........................................ 16

3.5.1 Ultramizer ......................................................... 16

3.5.2 Loading and saving user settings ..................... 17

3.6 Operating the Phones section .................................... 17

4. BPM and Effects section.................................................. 17

4.1 Effects section ............................................................ 18

4.1.1 Selecting the signal source ............................... 18

4.1.2 Activating an effect ............................................ 18

4.1.3 Selecting an effect ............................................ 18

4.1.4 Effect descriptions ............................................ 18

4.1.5 Editing effects ................................................... 19

4.1.6 BPM-synchronized effect parameters ............... 19

4.1.7 FX Setup ........................................................... 20

4.2 BPM Counter .............................................................. 20

4.3 MIDI Clock .................................................................. 21

5. Sampler ............................................................................. 21

5.1 Recording samples .................................................... 21

5.2 Playing back samples ................................................ 22

5.2.1 Insert function ................................................... 22

5.2.2 Reverse and Loop playback ............................. 22

5.2.3 Crossfader start ................................................ 22

5.2.4 Pitch Bend ........................................................ 22

5.3 Sampler effect ............................................................ 22

6. Further settings ................................................................ 23

6.1 Loading factory settings ............................................. 23

6.2 Output Setup .............................................................. 23

6.3 Adjusting display contrast ........................................... 23

7. The DDM4000 as MIDI controller ..................................... 23

7.1 MIDI protocol .............................................................. 23

7.2 Common MIDI settings ............................................... 23

7.2.1 Setting the MIDI channel .................................. 24

7.2.2 Sending a MIDI dump ....................................... 24

7.3 Conguring Microphone channel, Sampler and

crossfader as MIDI controller ..................................... 24

7.4 Conguring stereo channels as MIDI controller ......... 24

8. Installation......................................................................... 24

9. Specications ................................................................... 25

10. Appendix ......................................................................... 26

11. Warranty ......................................................................... 27

DIGITAL PRO MIXER DDM4000

Introduction 5

Introduction1.

Congratulations! The DDM4000 is a state-of-the-art 32-bit digital

DJ mixer, jam-packed with creative tools, yet its intuitive layout

will let you feel at home in an instant. Editing, storing and recalling

your settings is simply a breeze!

Hook up your turntables and CD/MP3 players to its 4 stereo

channels, each with fully programmable EQ and Kill switches. Put

ultimate versatility at your ngertips with fully programmable beat-

sync’able multi-FX modules, a pair of high-precision BPM counters

and a digital crossfader with custom curve adjustment. And the

super-cool BPM-sync’d sampler with real-time pitch control, loop

and reverse functions will make your crowd go wild.

Please read this manual to familiarize yourself with the +

control elements of the unit and its functions. After

you have carefully read this manual, keep it for future

reference.

Before you get started1.1

Shipment1.1.1

Your DDM4000 was carefully packed at the factory, and the

packaging was designed to protect the unit from damage caused

by rough handling. Nevertheless, we recommend that you carefully

examine the packaging and its contents for any signs of physical

damage that may have occurred during transit.

If the unit is damaged, please do NOT return it to us; +

instead, notify your dealer and the shipping company

immediately, otherwise claims for damage or replace-

ment may not be granted.

We recommend using a case to ensure optimal protec- +

tion of the device.

Please always use the original packaging to avoid da- +

mage due to storage or shipping.

Never let unsupervised children play with the DDM4000 +

or with its packaging.

Recycle whenever possible. +

Initial operation1.1.2

Ensure adequate air supply and to avoid overheating do not place

the unit near radiators etc.

Before you connect your DDM4000 to the mains, please +

make sure that your local voltage matches the voltage

required by the unit.

Caution! The following applies only to units that can be switched

between 120 V and 230 V: The fuse holder on the mains connector

has 3 triangular markings, with two of these triangles opposing

each other. The DDM4000 is set to the operating voltage printed

next to these markers and can be set to another voltage by turning

the fuse holder by 180°.

Please note that when operating the unit at 120 V, +

a higher fuse rating is required. Please refer to the

“Specications” for details.

If you set the unit to a different mains voltage, be sure +

to use a fuse of the correct type and rating. Please refer

to the “Specications” for details.

Blown fuses must be replaced by fuses of the same +

type and rating! Please refer to the “Specications”

for details.

Caution!

Before changing the fuse, switch off the device and +

pull the plug to avoid electric shock or damage to the

device.

The DDM4000 power connection is made by using the enclosed

cable and the amplier’s standard IEC receptacle. It meets all of

the international safety certication requirements.

Please make sure that all units have a proper earth +

connection. For your own safety, never remove or

disable the earth conductor from the unit or of the AC

power cord.

IMPORTANT NOTES CONCERNING

INSTALLATION

The sound quality may diminish within the range of pow- +

erful broadcasting stations and high-frequency sources.

Increase the distance between the transmitter and the

device and use shielded cables for all connections.

Online registration1.1.3

Please do remember to register your new BEHRINGER equipment

right after your purchase by visiting www.behringer.com (alterna-

tively www.behringer.de) and kindly read the terms and conditions

of our warranty carefully.

Should your BEHRINGER product malfunction, our goal is to

have it repaired as quickly as possible. To arrange for warranty

service, please contact the retailer from whom the equipment

was purchased. Should your BEHRINGER dealer not be located

in your vicinity, you may directly contact one of our subsidiaries.

Corresponding contact information is included in the original equip-

ment packaging (Global Contact Information/European Contact

Information). Should your country not be listed, please contact the

distributor nearest you. A list of distributors can be found in the

support area of our website (www.behringer.com).

Registering your purchase and equipment with us helps us process

your repair claims quicker and more efciently.

Thank you for your cooperation!

Caution!

Extreme output volumes may damage your hearing and/ +

or your loudspeakers. Turn down all volume and level

controls before you switch on the unit. Always set the

volume to an appropriate level.

DIGITAL PRO MIXER DDM4000

Controls and connections6

Controls and connections2.

This chapter describes the various controls and connections of the DDM4000 mixer. We have divided the console into several functional

sections for a better overview.

Overview of DDM4000Fig. 2.0:

2.1 Stereo channels 1 – 4

2.2 Microphone channel

2.3 Crossfader section

2.4 Main and Phones section

2.5 BPM and Effects section

2.6 Sampler

2.7 Rear panel connectors

2.8 Rear panel outputs

2.9 Power section

DIGITAL PRO MIXER DDM4000

Controls and connections 7

Stereo channels 1 – 42.1

Stereo channel stripsFig. 2.1:

The input select switch lets you switch between two signal {1}

sources. Select Line to hear the signal of the Line input [67].

Select Phono/Line to listen to the incoming source signal at

the Phono/Line [68] input.

The {2} GAIN knob adjusts the level of the input signal. The

actual level is displayed on the level meter {3}.

The 7-segment LED meter indicates the level of the input {3}

signal.

Each input channel features a 3-band equalizer ({4} HIGH, MID

and LOW) with kill feature, giving you up to 12 dB of boost

and a maximum cut of -? dB (kill). The kill feature lets you

mute the given frequency range. When each EQ knob is

turned fully left, the signal is effectively muted. All EQ para-

meters can be adjusted in Channel Setup.

The {5} MODE push button changes the functionality of the

preset push button {6} from Multi to Single.

The preset push buttons {6} P1, P2 and P3 allow you to store

and activate equalizer presets. When activated in Single

Mode, these push buttons provide a maximum cut of

-? dB (kill function).

Press the {7} PFL push button to listen in on the channel’s signal

using headphones.

The fader controls the channel volume.{8}

The {9} CURVE switch adjusts the response of the fader. In

SOFT Mode, the fader responds slower to steady fader

movement in the upper range and quicker in the lower range.

In Sharp Mode, the fader adjusts the volume quicker in the

upper third and slower in the lower range. In MID Mode,

the fader responds in a linear fashion. Since a difference

in volume levels is heard when switching between modes,

don’t use this switch while playing music!

The [10] CF ASSIGN push button lets you determine on which

side of the crossfader [20] (A or B) the signal is to be he-

ard.

Microphone channel2.2

Microphone channelFig. 2.2:

The [11] GAIN knob adjusts the level of the microphone signal

at the MIC 1 input.

This switch determines which signal is to be displayed on the [12]

level meter [13]. IN VU shows the unprocessed input level

which helps you to adjust the microphone signal correctly.

XMC VU shows the level after it has passed the Ultramic

processor.

The 7-segment LED meter indicates the level of the micro-[13]

phone channel.

The microphone channel strip features a 3-band equalizer [14]

(HIGH, MID and LOW). The range is +/-12 dB.

The [15] ON/OFF push button turns the microphone channel

on and off.

The [16] MIC SETUP push button opens the Mic Setup menu

on the display. This allows you to adjust the settings of the

equalizer, the Ultramic processor and the MIC FX (effects

processor).

The [17] XMC ON push button activates the ULTRAMIC pro-

cessor, which includes a 2-band compressor and expander.

Ultramic settings can be adjusted in Mic Setup.

The [18] MIC FX ON push button activates the microphone effects

processor. Select the effect in Mic Setup.

The [19] TALK ON push button activates the Talkover function.

This attenuates the volume level of the music as soon as you

speak into the microphone. This is a very useful function to

make yourself heard over the music being played. You can

adjust all the relevant settings in Talk Setup.

DIGITAL PRO MIXER DDM4000

Controls and connections8

Crossfader section2.3

Crossfader sectionFig. 2.3:

The replaceable crossfader is used to fade between the [20]

signals that are assigned to its two sides A and B. You can

assign the stereo channels and sampler using the CF Assign

push buttons [10] and [65].

The [21] CF ON push button activates the crossfader. When

the push button is not pressed, the signals of the individual

channels are routed straight to the Main outputs.

There are 3 Kill push buttons ([22] HIGH, MID and LOW) on each

side of the crossfader which let you mute the given frequency

range. In Crossfader Setup (see Chapter 3.4.2), it is pos-

sible to activate a special X-OVER mode that enhances the

crossfader’s functionality in combination with the Kill push

buttons. For more information, read Chapter 3.4.1.

Press the [23] FULL FREQ push button to remove any frequency

cuts of the KILL EQ [22].

The CURVE knob lets you seamlessly adjust the response [24]

of the crossfader.

The REVERSE function allows you to reverse the conguration of

the crossfader. This way you can toggle between Channel A and

B at the ick of a switch.

REVERSE HOLD[25] activates a permanent Reverse function.

The crossfader fades between sides A and B in the reverse

direction. This means that A is now on the right and B on

the left side.

REVERSE TAP[26] activates a momentary Reverse function.

This means that A and B are interchanged as long as the

TAP push button is held down.

The BOUNCE TO MIDI CLOCK function provides an automa-

tic, quick crossfading synchronized to the rhythm of the music

(“bouncing”). The bounce speed is determined by the MIDI

Clock.

Press the [27] BOUNCE TO MIDI CLK push button to ac-

tivate the bouncing. Once the push button is pressed,

the signal repeatedly jumps from A to B and back again

corresponding to the interval pre-selected by using the BEAT

push buttons [28].

The [28] BEAT push buttons let you determine the Bounce rate,

which can range between one and 16 beats.

These LEDs indicate the number of beats you have [29]

chosen.

Find a detailed description of this function in Chapter +

3.4.3.

DIGITAL PRO MIXER DDM4000

Controls and connections 9

Main and Phones section2.4

Main and Phones sectionFig. 2.4:

MAIN OUTPUT:

The [30] OUTPUT A knob controls the volume of output A

([73]).

The [31] BALANCE knob adjusts the stereo panning of output

The [32] OUTPUT B knob controls the volume of output B

([74]).

The high-resolution, 22-segment [33] OUTPUT LEVEL meter

indicates the level of the output signal on OUTPUT A.

ULTRAMIZE ON/OFF[34] push button: The Ultramizer is an

effect that enhances the loudness and assertiveness by

dynamic compression. In Ultramizer Setup (see Chapter

3.5.1), you can congure the Ultramizer.

The [35] LOAD push button lets you load the user settings of the

entire mixer. The settings that are active when the device is

turned off are loaded when the device is switched back on

again. Read more about saving and loading user settings

in Chapter 3.5.2.

PHONES:

Connect the headphones to the [36] PHONES jack (1/4" TRS

connector).

The [37] OUTPUT knob controls the volume of the head-

phones.

The [38] MIX knob adjusts the balance between PFL signal and

PGM signal (PFL = Pre Fader Listening, fader independent

pre-listening of individual channels; PGM = Program, Master

signal). When the knob is turned completely to the left, you

only hear the PFL signal, whereas when turned completely

to the right the Master signal is heard. Between these two

positions, you can adjust the mix of both signals.

The [39] PUNCH EQ function helps synchronize two tracks. You

can orient yourself to the snare or the bass drum or both.

Press the SNARE or BASS push button to emphasize the

selected sound in the headphones.

When the [40] SPLIT push button is pressed, the PFL signal is

heard in the left headphone and the PGM signal is only heard

in the right headphone.

BPM and Effects section2.5

BPM Counter and Effects section (here FX1)Fig. 2.5:

The DDM4000 has 2 identical effects units. There are 2 additional

independent effects units for the mic signal and the Sampler. All

effects can be used at the same time. The BPM Counter and MIDI

Clock are also found in this section.

The graphic display shows BPM values, effect names and [41]

effect parameters as well as channel assignments. It also

leads you through Console Setup.

The [42] FX ON push button activates the effects unit.

Press the [43] FX ASSIGN push button to assign an effects unit

to a signal source (push button ashes). The possible input

sources are listed on the display. Select the preferred source

by turning and pressing the PARAMETER knob [45].

The [44] DEPTH knob adjusts the effect intensity (depth). For

some effects, it also lets you adjust the mix between the

original signal (dry) and the effect signal (wet).

Press the[45] PARAM(eter) knob to select the effect parameters.

By turning the knob, you can change the parameter shown

on the display.

Press [46] SELECT/LOW to access the effects list (on the dis-

play). Turn and press the knob [45] to load a preset.

Press the [47] PARAM/MID push button to access the effect para-

meters. Turn the knob [45] to change the parameter value.

Press [48] DEFAULT/HIGH to restore a preset.

When the effect is activated (by pressing the FX ON +

push button), the push buttons [46] (LOW), [47] (MID)

and [48] (HIGH) are used as Kill switches in the effect’s

signal path.

Depending on the selected effect, the [49] BEAT push buttons can

adjust time-related parameters. However, the values entered

are not in milliseconds or similar units, but in beats.

To enter the tempo manually, tap this push button (at least [50]

2 x) in the rhythm of the music (TAP). By keeping the AUTO

BPM/TAP push button pressed a little longer (> 1 s), the

automatic tempo input (AUTO BPM) is reactivated.

Turn the [51] CONSOLE SETUP knob to adjust the tempo of

the MIDI Clock (press and turn simultaneously = coarse

adjustment). A short press on the knob conrms the entry

made. A long press on the knob lets you access Console

Setup (see Chapter 3.1).

The [52] MIDI START/STOP/ESC turns on the MIDI Clock.

The [53] ADJUST push buttons let you transfer the tempo of the

BPM counter to the MIDI Clock.

All functions of the BPM and Effects section are de- +

scribed in detail in Chapter 4.

DIGITAL PRO MIXER DDM4000

Controls and connections10

Sampler2.6

Sampler sectionFig. 2.6:

Press the [54] INSERT push button to add the sampler signal to

the channel (Insert Mode). If the push button is not activated,

the sampler is mixed to the selected channel (Mix Mode).

In both cases, playback is initiated with the REC SOURCE

push buttons. When the sampler is routed to the crossfader,

the LED of the INSERT push button goes out.

The [55] VOLUME/MIX knob controls the volume of the sampler

(in Mix Mode) as well as the volume balance between input

signal and Sampler (in Insert Mode).

The [56] REC SOURCE push buttons let you select the channel

for recording and playing back samples.

Press the [57] PFL push button to listen in on the sampler signal

with the headphones.

SAMPLE LENGTH [58] adjusts the recording time (1 – 16 beats

or endless recording ?).

RECORD/IN [59] lets you record to the Sampler. Select a bank

beforehand. By pressing the push button a second time, the

recording is stopped (only in ? Mode).

BANK ASSIGN[60] is used to select a bank in which the recor-

ded material is stored. The selected bank is indicated by

the relevant MODE push button [61] which signalizes the

readiness to record.

The [61] MODE push buttons (Bank 1 and Bank 2) are used to

select the sampler’s types of playback (Reverse and Loop).

A short tap activates or deactivates the Reverse function;

pressing the push button a little longer activates or deac-

tivates the Loop function.

Press the PLAY/OUT[62] push button to start the playback of the

recorded sample. When the Loop function is deactivated,

the sample is only played back as long as the PLAY push

button is pressed.

Press [63] SMP FX ON push button to activate the Brake ef-

fect.

Press the [64] SELECT push button to determine the length of

the brake (1, 4 or 8 Beat Brake, which is shown in the center

of the display).

The [65] CF ASSIGN push button lets you determine on which

side of the crossfader the sampler signal is to be routed

to.

You can even trigger the sampler with the crossfader when [66]

the sampler is assigned to it. To order to do so, simply press

the CF START push button. But beforehand, use BANK

ASSIGN to select the bank that should be played back when

using the fader.

Rear panel connectors2.7

Rear panel connectorsFig. 2.7:

The [67] LINE inputs are used to connect the Line signals (for

example, CD players, soundcards and drum machines).

The [68] PHONO inputs let you connect turntables.

Use the [69] PHONO/LINE switches to set the PHONO inputs to

Line level in order for you to be able to connect a CD player

to the PHONO inputs.

Caution! Devices with Line output levels, such as CD +

players, can cause distortion and destroy the preamp-

lier. Press the PHONO/LINE switch before connecting

devices with Line level to the highly sensitive PHONO

inputs.

The [70] GND connectors are used to ground the turntables.

The balanced XLR connectors provide a connection for [71]

dynamic microphones.

This is the [72] LEVEL control for the MIC 2 input.

DIGITAL PRO MIXER DDM4000

Controls and connections 11

Rear panel outputs2.8

Rear panel connectorsFig. 2.8:

These are the [73] OUT A outputs (XLR) allowing you to connect

to an amplier. Use the OUTPUT A control [30] to adjust the

volume level. Additionally, the SUBWOOFER output lets

you hook up a subwoofer. A crossover is integrated into the

DDM4000. The crossover frequency is adjusted in Output

Setup (see Chapter 6.2).

When powering up the system, turn on the connected +

amplier last to prevent spikes that can easily damage

your loudspeakers. Before turning on the amplier,

make sure that no signal is going through the DDM4000

in order to avoid sudden and unpleasant surprises.

We recommend turning down all faders and knobs

beforehand.

The MAIN OUT connector panel consists of [74] OUT A, OUT

B and TAPE outputs:

The signal at = OUT A is the same as at the XLR outputs

[73].

You can connect an additional amplier to output = OUT

B which can be used for a DJ booth or a second club

zone, for example. The volume of the OUT B signal is

(independent of OUT A) individually adjusted with the

OUTPUT B knob [32].

The = TAPE output allows you to connect a recording de-

vice in order to tape-record your mix. The output level is

independent of OUT A and OUT B and can be adjusted

in Output Setup (see Chapter 6.2).

DIGITAL OUT [75] is the digital output of the DDM4000.

This is where you find the TAPE signal in CD quality

(16 bit/44.1 kHz).

Use Output Setup (see Chapter 6.2) to adjust further +

settings of the output section.

These are the [76] MIDI IN, MIDI OUT and MIDI THRU connec-

tors that allow you to connect external MIDI equipment and

synchronize with their MIDI Clock.

Read more about the MIDI functions of the DDM4000 +

in Chapter 7.

Power section2.9

The POWER sectionFig. 2.9:

Power is supplied via an [77] IEC connector. The matching cable

is provided with the unit.

FUSE RETAINER/VOLTAGE SELECTOR[78] . Please make sure

that the voltage indicated by the voltage selector matches the

local voltage before you connect the unit to the main power

supply. Always replace blown fuses with fuses of the same

type and rating. Some units feature a fuse retainer in which

a selection between 230 V and 120 V is possible. Please

be aware: When using your unit outside of Europe with 120

V, a fuse with a higher rating is required.

Use the [79] POWER switch to turn on the DDM4000. Before

connecting the unit to the power mains, ensure that the PO-

WER switch is in OFF position. When the unit is in operation,

ensure that the mains plug is accessible.

Attention: The POWER switch does not fully disconnect +

the unit from the mains. To disconnect the unit from

the mains, pull out the main cable plug or appliance

coupler. When installing the product, ensure the plug

or appliance coupler is readily operable. Unplug the

power cord completely when the unit is not used for

long periods of time.

The serial number of the DDM4000 is found on the bottom side

of the device.

DIGITAL PRO MIXER DDM4000

Controls and connections12

Hookup example2.10

CD players

Turntables

Microphones

Drum Computer

Digital recorder

DJ Booth

Dancefloor

Application example of hooking up the DDM4000Fig. 2.10:

DIGITAL PRO MIXER DDM4000

Operation 13

Operation3.

Console Setup3.1

Console Setup allows you to make all standard settings for the

DDM4000.

Press the CONSOLE SETUP knob 1) [51] for approximately 2

seconds. The setup list appears in the center of the display.:

Turn the CONSOLE SETUP knob to select the setup you 2)

want to edit.

Press the CONSOLE SETUP knob to conrm the selection.3)

Exit Console Setup:

Press the ESC push button = [52] to exit Console Setup.

Some of the setup pages can be accessed in different ways. This

is the case for Mic Setup and User Settings:

Open Mic Setup:

Press the MIC SETUP push button 1) [16] to access Mic

Setup.

Press the MIC SETUP push button 2) [16] again to exit Mic

Setup.

Open User Settings:

Press the LOAD push button 1) [35] to access User Settings.

Press the LOAD push button 2) [35] again to exit User Set-

tings.

Selection lists on screen3.1.1

The individual setup pages contain further selection lists, which

appear either on the left or right side of the display, in addition to

the Console Setup list.

Left:

Turn the left PARAMETER knob 1) [45] (in the FX1 section) to

select the preferred function from the list.

Press the left PARAMETER knob to conrm the selection.2)

Right:

Turn the right PARAMETER knob 1) [45] (in the FX2 section) to

select the preferred function from the list.

Press the right PARAMETER knob to conrm the selection.2)

Using stereo channels3.2

EQ modes: SINGLE and MULTI3.2.1

The equalizer provides Preset push buttons, labeled P1, P2 and

P3, with which preset congurations are stored. The behavior

of the push buttons depend on the selected EQ mode: Single

Mode or Multi Mode. After switching on the device, Single Mode

is active.

SINGLE Mode:

In Single Mode, the push buttons P1, P2 and P3 {6} are each

permanently assigned to a frequency band (P1 = HIGH, P2 = MID,

P3 = LOW). This means that a Preset can be assigned to each

EQ control. When activated, the Preset push buttons provide a

Kill function with maximum attenuation (-? dB).

Preset settings in SINGLE Mode

HIGH Kill -? dB

Suppresses high frequencies

MID Kill -? dB

Suppresses mid frequencies

LOW Kill -? dB

Suppresses low frequencies

Functionality of Preset push buttons in Single ModeTab. 3.1:

The degree of cut can, however, be modied. Alternatively, a fre-

quency boost can also be stored. In case you want to boost instead

of cutting the bass (Punch function), proceed as follows:

Turn the LOW knob 1) {4} to the right until you have reached

the boost you want.

Press and hold the MODE push button 2) {5} while pressing

P3 {6}.

Press P3 to load the Preset. The bass frequencies are now 3)

boosted. P3 ashes blue.

This way you can also program the mids and highs with P2 and

P1 respectively.

Reset:

The Preset push buttons can be restored to their initial states at

all times (Reset function):

Press MODE = {5} for approximately 2 seconds. The MULTI

LED briey lights up to conrm the reset.

MULTI Mode:

In Multi Mode, the Preset push buttons are not assigned to in-

dividual EQ bands, but are assigned to the 3-band equalizer as

a whole. This way you can create three EQ presets and assign

these to the Preset push buttons. When activated, the Preset push

buttons are assigned as follows:

Preset settings in MULTI Mode

P1 High pass Suppresses MID and LOW

P2 Band pass Suppresses HIGH and LOW

P3 Low pass Suppresses HIGH and MID

Functionality of Preset push buttons in Multi ModeTab. 3.2:

To activate Multi Mode, press the MODE push button = {5}.

The MULTI LED lights up.

To create your own EQ presets, proceed as follows:

Adjust the equalizer as needed by turning the LOW, MID and 1)

HIGH knobs.

Press and hold the MODE push button 2) {5} while pressing

P1 {6}.

Press P1 to load the EQ Preset. P1 ashes yellow.3)

Two more EQ Presets can be stored with P2 and P3.

Reset:

The Preset push buttons can be restored at all times:

Press MODE for approximately 2 seconds. The SINGLE LED =

briey lights up to conrm the reset.

DIGITAL PRO MIXER DDM4000

Operation14

Channel Setup3.2.2

In Channel Setup, you can ne-tune the characteristics of the

stereo channels’ equalizer. It is also possible to adjust a Subsonic

Filter (low-cut lter) for all four channels. For example, this lter can

be used to suppress low-frequency noise from turntables.

Press the CONSOLE SETUP knob 1) [51] for approximately 2

seconds.

Select “Channel Setup” by turning and pressing the CONSOLE 2)

SETUP knob.

Channel Setup appears on the display.

The equalizer of the stereo channels has 3 bands with different

characteristics. The Mid band is a peak lter whose center fre-

quency and bandwidth (Q factor) can be modied. Both outer

bands Low and High are shelving lters. In Channel Setup,

following settings are available for each of the 4 channels:

Channel Xover (Crossover):

LOW: Cutoff frequency of the Low lter. All frequencies below

the adjusted value are cut or boosted.

MID: Center frequency of the Mid band. All frequencies

around this value are boosted or cut. The bandwidth is

determined by the parameter Mid Q (see below).

HIGH: Cutoff frequency of the High lter. All frequencies above

the adjusted value are boosted or cut.

Press the left PARAMETER knob 1) [45] to select the parameter

(LOW, MID or HIGH).

Turn the PARAMETER knob to change the cutoff frequency 2)

and center frequency of the selected band.

Mid Q:

The Q factor determines the behavior of the lter. The higher the

value, the narrower the bandwidth. Mid Q affects the mids band.

Turn the CONSOLE SETUP knob = [51] to change the value

of the Q factor.

Subsonic frequency:

You can adjust the cutoff frequency of the low-cut lter on each

stereo channel. All frequencies below the cutoff frequency are

attenuated.

Press the right PARAMETER knob 1) [45] to select the chan-

nel.

Turn the PARAMETER knob to change the cutoff frequency.2)

Exiting Channel Setup:

Press the ESC push button = [52] to exit Channel Setup.

Operating the Microphone channel3.3

Mic Setup3.3.1

You can make adjustments to the sound settings of the Microphone

channel, the Ultramic processor and the Mic effects by using Mic

Setup. This is how to access Mic Setup:

Press the CONSOLE SETUP knob 1) [51] for approximately 2

seconds.

Select “Mic Setup” by turning and pressing the CONSOLE 2)

SETUP knob.

Alternatively, you can access Mic Setup as follows:

Press the MIC SETUP push button = [16] on the microphone

channel. The MIC SETUP push button lights up as long as

you are using Mic Setup.

Mic Setup appears on the display containing several submenus.

On the left-hand side of the display you see a list from which the

following submenus can be selected:

Turn the left PARAMETER knob = [45] to select the submenu

you want to edit:

EQ Freq/Pan page:

This page shows level meters for both microphone signals. In

addition, you can make sound settings for the equalizer on the

Microphone channel. Here you can adjust the stereo image of the

microphone signal as well as the signal relation of both micropho-

nes to each other. The individual parameters are as follows:

MIC1: Level meter for Microphone 1

MIC2: Level meter for Microphone 2

LOW: Cutoff frequency of the LOW control knob

MID: Center frequency of the MID control knob

HIGH: Cutoff frequency of the HIGH control knob

Q MID: Q factor of the mids band

Press the CONSOLE SETUP knob 1) [51] to select the parameter

(LOW, MID, HIGH, Q MID).

Turn the CONSOLE SETUP knob to change the value of the 2)

selected parameter.

PAN1: Position of Microphone 1 in the stereo image

PAN 2: Position of Microphone 2 in the stereo image

OUT B: Volume of the microphone channel at Output B

Press the right PARAMETER knob 1) [45] to select the parameter

(PAN 1, PAN 2, OUT B).

Turn the PARAMETER knob to change the value of the 2)

parameter.

EQ GAIN page:

This page lets you make user default sound settings, which affect

the microphone channel in relation to the equalizer. For example,

storing a boost of 5 dB in these settings affects the signal even

when the HIGH rotary knob is set to 0, that is the center position.

The high frequencies can additionally be boost or cut with the HIGH

knob. This function helps to remove problematic frequencies of

your voice or to improve speech comprehensibility.

DIGITAL PRO MIXER DDM4000

Operation 15

MIC1 LOW CUT: Cutoff frequency of the high-pass lter

(Microphone 1)

MIC1 LOW, MID, HIGH: EQ default settings for Microphone

Press the CONSOLE SETUP knob 1) [51] to select the parameter

(LOW, MID, HIGH).

Turn the CONSOLE SETUP knob to change the value of the 2)

selected parameter.

MIC2 LOW CUT: Cutoff frequency of the high-pass lter

(Microphone 2)

MIC2 LOW, MID, HIGH: EQ default settings for Microphone 2

Press the right PARAMETER knob 1) [45] to select the parameter

(LOW, MID, HIGH).

Turn the PARAMETER knob to change the value of the 2)

selected parameter.

ULTRAMIC 1 and 2:

The Ultramic processor is a 2-band compressor that reduces the

dynamic range of speech. The level of loud sounds is reduced

and the level of quiet sounds is raised. This decreases the diffe-

rence between the loudest and quietest passages. By splitting the

signal into two frequency bands, a thicker, more powerful sound

is achieved without the typical artifacts, such as pumping sound

or a loss of clarity.

The settings for both microphone signals are made separately.

That’s the reason for having two Ultramic pages. For Mic 1, select

the page “Ultramic 1” and choose “Ultramic 2” for Mic 2. The

parameters on both pages are identical so that they only have to

be described once.

You can see several level meters on the display. Three para-

meters of the compressor are adjustable plus you can also load

presets.

The meters:

MIC I Shows the input level

MIC 0 Shows the output level

COM Shows the compression ratio for the low (L) and high

(H) frequency band

EXP Shows the attenuation of the expander for the low (L)

or high (H) frequency band

Adjustable parameters

THRSH Threshold species the cutoff frequency of the Ult-

ramic processor

FREQ Adjusts the crossover frequency between the upper

and lower frequency band

EFFIC Efciency: Adjusts the level of compression

Press the CONSOLE SETUP knob 1) [51] to select the parameter

(THRSH, FREQ, EFFIC).

Turn the CONSOLE SETUP knob to change the value of the 2)

selected parameter.

Ultramic presets:

The following default settings can be loaded:

Turn the right PARAMETER knob 1) [45] to select the preset.

Press the PARAMETER knob to load the preset.2)

MIC FX page:

On the Mic FX page, you can select the type of effect you want

to use for the microphone signal. The following effects are

available:

Turn the right PARAMETER knob 1) [45] to select the preset.

Press the PARAMETER knob to load the preset.2)

Each effect can be modied in order to suit your individual taste.

Two parameters are available for this reason. The second para-

meter always adjusts the effect Dry/Wet Mix—this applies to all

effects.

Effect descriptions:

FLANGER: A anger effect occurs through frequency modu-

lation. You can adjust the speed of the LFO (Low Frequency

Oscillator).

PHASER is similar to a anger. Only this time around, modulation

is achieved through phase-shifting. You can adjust the speed of

the LFO.

DELAY is a signal delay. You can change the delay time (Time).

ECHO is similar to the delay effect, with the difference that the

delayed signal is repeated several times.

PITCH changes the pitch of the signal and therefore the pitch of the

vocalist’s and speaker’s voice. Shift is used to adjust the pitch.

BITCRUSHER reduce the digital resolution. The bit depth is

adjustable.

REVERB is a reverberation effect. Eight different types of rever-

beration are available. These are described in detail in Chapter

4.1.4.

Press the CONSOLE SETUP knob 1) [51] to select a parame-

ter.

Turn the CONSOLE SETUP knob to change the value of this 2)

parameter.

You can match the time parameter of the anger, phaser, delay

and echo effects to the beat by tapping the tempo with the left TAP

push button (50) as long as Mic Setup is displayed (MIC SETUP

push button [16] shines when active).

Exiting Mic Setup:

Press the ESC push button = [52] to exit Mic Setup.

DIGITAL PRO MIXER DDM4000

Operation16

Talk Setup3.3.2

The Talkover function is useful when making announcements

while the music is playing. The level of the music, is attenuated

as soon as you speak into the microphone. All necessary settings

of this function are made in Talk Setup. This is how you access

Talk Setup:

Press the CONSOLE SETUP knob 1) [51] for approximately 2

seconds.

Select “Talk Setup” by turning and pressing the CONSOLE 2)

SETUP knob.

The Talk Setup page appears on the display.

This page displays level meters for both microphones. On the

left-hand side of the screen, there is a list from which you can

select a Talkover preset.

Loading presets:

Turn the left PARAMETER knob 1) [45] to select the preset.

Press the PARAMETER knob to load the preset.2)

Editing talkovers:

The following parameters of the Talkover function are adjust-

able:

THRSH Threshold. The music signal is attenuated as soon

as the microphone signal exceeds this value.

MAX. ATT Maximum Attenuation. This lets you adjust the

music’s maximum attenuation while speaking into

the microphone.

SPEED Adjusts the speed at which the signal’s volume

level is reduced.

Press the right PARAMETER knob 1) [45] to select the parameter

(THRSH, MAX. ATT, SPEED)

Turn the PARAMETER knob to change the value of the 2)

parameter.

Exiting Talk Setup:

Press the ESC push button = [52] to exit Talk Setup.

Operating the crossfader3.4

The use of the Crossfader is easy to understand, even for a DJ

novice. But the DDM4000 wouldn’t be a digital mixer if it hadn’t a

couple of special functions to offer that cannot be easily realized

with an analog DJ Mixer.

Crossfader modes: KILL and X-OVER3.4.1

There are three push buttons labeled HIGH, MID and LOW ([22])

on the left-hand side and on the right-hand side of the Crossfader.

When activated, they function as Kill switches, that is they can

suppress specic frequency bands.

X-Over (Crosssover) Mode lets you realize completely new,

breathtaking effects. In this mode, it is possible to assign specic

frequency bands to Side A and B that can then be crossfaded.

Here’s an example to make the functionality clear:

Move the crossfader 1) [20] to the left (A).

Press the FULL FREQ push button 2) [23] in Section A.

Press the Kill push button 3) [22] “MID” in Section B.

In the left crossfader position, the A signal is played back in its

complete frequency range. By moving the crossfader to the right,

only the mid frequencies of the B signal are faded in while the mids

of the A signal are faded out. The low and high frequencies of the

A signal remain audible. As a result, the low and high frequencies

of the A signal together with the mid frequencies of the B signal

are audible at the output of the mixer. X-Over Mode keeps your

mixing style fresh and unique. You can activate X-Over Mode in

Crossfader Setup.

Crossfader Setup3.4.2

This is how you access Crossfader Setup:

Press the CONSOLE SETUP knob 1) [51] for approximately 2

seconds.

Select “Crossfader Setup” by turning and pressing the CON-2)

SOLE SETUP knob.

The Crossfader Setup page appears on the display:

On the display’s left side, you can adjust the frequency crossfade

of the Kill push buttons. On the right side, you can select Cross-

fader Mode.

XOVER CF (Crossover Center Frequency):

LOW: Crossover frequency between LOW and MID

HIGH: Crossover frequency between MID and HIGH

Press the left PARAMETER knob 1) [45] to select the parameter

(LOW, HIGH).

Turn the PARAMETER knob to change the value fo the 2)

selected parameter.

Crossfader Mode:

Turn the right PARAMETER knob 1) [45] to select the mode

(KILL, X-OVER).

Press the PARAMETER knob to conrm.2)

Exiting Crossfader Setup:

Press the ESC push button = [52] to exit Crossfader Setup.

Bounce to MIDI Clock3.4.3

This function automates bouncing. Bouncing is hard crossfading

with the crossfader in the rhythm of the music. The internal MIDI

Clock needs to be active for this function to work. The clock is

a reference for the bounce speed that ranges between one and

16 beats.

Before pressing the BOUNCE TO MIDI CLK push button to start

the bounce, you should specify a the Bounce speed:

Start the MIDI Clock by pressing MIDI START-STOP push 1)

button [52].

Select the bounce speed by using the BEAT push buttons 2)

[28]. The LEDs [29] indicate the beats.

Now press the BOUNCE TO MIDI CLK push button 3) [27] to

start the bounce. When the crossfader is on Side A, the bounce

starts with the A signal, whereas when the crossfader is on B,

the bounce starts with the B signal.

Operating the Main section3.5

There are also several functions in the Main section that surpass

the functional capacity of an analog mixer. This way complete mixer

settings can be stored and loaded. And the Ultramizer makes sure

that your beats sound even fatter.

Ultramizer3.5.1

The Ultramizer is a multiband processor that compresses the

audio signal in order to achieve a better perception of volume

without having to increase the level. As a result, the performance

of an amplier is optimally used and your music feels louder than

it really is. The processing takes place in two individual frequency

bands in order to achieve a more powerful sound without the

unwanted side effects, such as the pumping effect and loss of

high frequencies.

Press the ULTRAMIZE ON/OFF push button 1) [34] to activate

the Ultramizer.

Press the CONSOLE SETUP knob 2) [51] for approximately 2

seconds.

Select “Ultramize” by turning and pressing the CONSOLE 3)

SETUP knob.

DIGITAL PRO MIXER DDM4000

BPM and Effects section 17

The display switches to the Ultramizer page. Here you can change

settings plus load and edit presets:

Loading presets:

Turn the left PARAMETER knob 1) [45] to select the preset.

Press the PARAMETER knob to load the preset.2)

Ultramizer presets

Gentle Boost Gentle volume boost

Boost Noticeable volume boost

Pump Strong volume boost with pumping effect

Full Maximum volume boost

Full Pump Maximum volume boost with pumping effect

Editing the Ultramizer:

RANGE Describes the adjustable dynamic range. A value of 10

dB results in a maximum level boost of 10 dB.

TIME Changes the adjustable speed of the Ultramizer.

Turn the CONSOLE SETUP knob = [51] to change the TIME

parameter.

Turn the PARAMETER knob = [45] to change the RANGE

parameter.

Exiting the Ultramizer setup:

Press the ESC push button = [52] to exit the Ultramizer setup.

Loading and saving user settings3.5.2

A great advantage of a digital mixer is the possibility to store

entire mixer settings in order to recall them later on at the ick of

a switch. Big studio consoles refer to this function as “Snapshot”

because all settings are captured (as with a snapshot). This lets

you adjust the mixer to your way of working and recall settings

you made at any time.

Just imagine, a club has the DDM4000 which is being used

by several DJs. Each DJ has stored personal EQ settings, kill

frequencies, Ultramizer and Effect settings, so that when it is his

or her turn, the preferred settings can be recalled immediately.

The other way around, a guest DJ, who is not accustomed to the

DDM4000, is able to take off without having to adjust any settings

in advance.

After switching on the device, the last selected preset +

is loaded.

Loading user settings:

Press the LOAD push button 1) [35]. The LOAD push button

ashes.

“User Setup” appears on the screen, displaying the preset list:

Turn the left PARAMETER knob 2) [45] to select a user setting

(or the factory preset).

Press the PARAMETER knob again to load the user setting.3)

Storing user settings:

Press the LOAD push button 1) [35] to access User Setup with

its preset list.

Turn the CONSOLE SETUP knob 2) [51] to select a memory

location.

Press the CONSOLE SETUP knob to store the user setting.3)

It is not possible to overwrite the factory preset. +

Exiting User Setup:

Press the LOAD push button = [35] or the ESC push button

(52) to exit User Setup.

Operating the Phones section3.6

You can use the headphones to listen to two different signals: 1.

The PGM signal (=Program): This is the signal at the MAIN output.

2. The PFL signal (=Pre Fader Listen): This is the signal which

can be routed to the PFL bus by using the PFL push buttons {7}.

The PFL signal is fader-independent, which means it can even be

heard when the faders are pulled down.

When the SPLIT push button [40] is not pressed, both the PGM

and PFL signal are played back in stereo in the headphones.

The mix of both signals is adjusted with the MIX knob [38]. When

the knob is turned completely to the left, the PFL signal is heard,

whereas when turned completely to the right, the PGM signal is

heard in both headphones.

Working in Split Mode:

Press the SPLIT push button = [40] to activate Split Mode.

When using Split Mode, the PFL signal is played back on the

left headphone while the PGM signal is played back on the right

headphone (both mono signals).

BPM and Effects section4.

BPM and Effects sectionFig. 4.1:

The BPM and Effects section in the middle of the mixer can eit-

her be used for the stereo channels or the master signal. Both

processors can also be combined to be used as dual effect for

individual channels. What’s more, both Microphone channel and

Sampler feature their own effect processors, which are described

in individual chapters (Chapter 3.3.1 and Chapter 5.4).

Display:

The display shows the following information:

A Shows the effect type and the parameter values.

B Shows the calculated speed in BPM (Beats Per Minute).

It also gives information on the signal assignment and the

Tap function.

C This section shows the BPM-synchronized effect parameters

as beats on the right side. On the left, you see the activity

of the Kill function in the effect path.

D This information refers to the Sampler and/or the MIDI Clock

(see Chapter 5).

DIGITAL PRO MIXER DDM4000

BPM and Effects section18

Effects section4.1

Effects section (here FX 1)Fig. 4.2:

Selecting the signal source4.1.1

To use an effect, you rst have to assign the effect to a signal

source. This assignment also applies to the BPM Counter. Possible

input sources are as follows:

INPUT 1 – INPUT 4: Stereo channels 1 – 4.

MUSIC: Stereo sum signal (main signal).

CHAIN: CHAIN assigns the effect to the signal of

the other effects section, so that 2 effects

are triggered consecutively.

Selecting a signal for FX1:

Press the FX1 ASSIGN push button 1) [43].

Turn the left PARAMETER knob 2) [45] to select a signal source

from the list.

Press the left PARAMETER knob to conrm the selection.3)

Selecting a signal for FX2:

Press the FX2 ASSIGN push button 1) [43].

Turn the right PARAMETER knob 2) [45] to select a signal source

from the list.

Press the right PARAMETER knob to conrm the selection.3)

Activating an effect4.1.2

Press the FX ON push button 1) [42] to activate the effect. Both

the FX ON push button and the EFFECT/BAND push button

[46] – [48] ash.

Turn the DEPTH knob slowly to the right until you hear the 2)

effect as is intended.

Kill function on the effect path:

A specially effective way of alienation is to remove individual

frequency bands from the effect processing. There are three ad-

ditional Kill switches that are found on the signal path leading to

the effects unit. The EFFECT/BAND push buttons of the activated

effect ash blue corresponding to the frequency bands that are

active. By pressing the push buttons you are able to "kill" the fre-

quency bands. And the display shows the Kill function’s status.

Press one of the EFFECT/BAND push buttons ( = [46], [47],

[48]) while the effect is active. The push-button LED of the

deactivated band goes out.

Selecting an effect4.1.3

Nine effect types are available. The effect table in Chapter 4.1.4

gives an overview of the possible effects and their adjustable

parameters.

Press the SELECT push button 1) [46]. The display shows a list

of all types of effects.

Turn the PARAMETER knob 2) [45] to select the effect type.

Press the PARAMETER knob to load the effect type.3)

Effect descriptions4.1.4

The following gives you a description of the available effects

and adjustable parameters. (BPM-synchronized parameters are

printed in italic.) The tables show you which controls are used to

adjust the parameters. Chapter 4.1.5 describes effect processing.

Chapter 4.1.6 gives you the information you need to know about

BPM-synchronized parameters.

FLANGER, PHASER, PAN:

FLANGER: The anger effect is achieved by frequency modula-

tion. You are able to adjust the speed of the LFO (Low Frequency

Oscillator), the amount of the effect signal that is fed back to the

input (Feedback), the effect depth (Depth) and the degree of

phase shifting represented in rhythmical units (Phase). Use Fade

in case you want the anger to complete its period of oscillation

after the effect has been turned off, to avoid an abrupt truncation

of the effect.

PHASER is similar to the anger. In this case the modulation is

achieved through phase shifting. You can adjust the speed of the

LFO and the effect depth (Depth). Use Fade to determine if the

effect is to end abruptly or softly fade out.

PAN specied an effect which lets the signal move from the right

to the left side of the stereo image. This effect sounds the most

intensive when the DEPTH knob is turned right up. LFO adjusts

the speed of the panning and Depth adjusts the effect depth.

Effect parameters for Flanger, Phaser and PanningTab. 4.1:

DELAY, ECHO:

DELAY is a signal delay. The delay time (Time) can by synchro-

nized with the BPM Counter. A simple delay (Simple) and the

3-Pong Delay, which spreads the delays across the whole stereo

image, are available.

ECHO is similar to the delay. The only difference is that the

delayed signal is repeated several times. Use Feedback to spe-

cify the number of times that the delay is to be repeated. Fade

determines if the echo is to fade out (On) or not (Off) when the

effect is turned off.

DIGITAL PRO MIXER DDM4000

BPM and Effects section 19

Effect parameters for Delay and EchoTab. 4.2:

PITCHER, BITCRUSHER:

PITCHER changes the pitch of the music without changing the

tempo. Shift adjusts the pitch.

BITCRUSHER simulates a decrease in the digital resolution. From

soft lo- settings to toy sounds, everything is possible.

Effect parameters for Pitch and BitcrusherTab. 4.3:

REVERB:

REVERB is a reverberation effect. Eight different reverb room si-

mulations are available. When Fade is activated, the reverberation

decays and is not truncated in case the effect is turned off.

Ambient is a very short reverb which lets you virtually hear the

walls of the room.

Box delivers a spatial impression without long reections.

Cathedral: The long and dense reverb of a big cathedral, ideal

for slow tracks.

Cavern: An intensive, high-frequency-dominant reverb based on

a cave with rocky walls.

Chamber produces the short reverb of a small room.

Chorus: A thick, warm reverberation which is shorter than that

of Cathedral.

Concert simulates the well-dened reverb of a big concert hall.

Echo: A thick, short reverb with a longer pre-delay.

Effect parameters for ReverbTab. 4.4:

FILTER:

FILTER is an effect which is typically associated with synthesizer

music. Three types of lters are available: Band Pass, Low Pass

and High Pass. Resonance is used to increase the level of the

lter frequency which makes the effect sound more intensive. In

LFO Mode, the lter frequency is controlled by an LFO. Manual

Mode lets you control the lter frequency with the DEPTH knob

[44].

Effect parameters for FilterTab. 4.5:

Editing effects4.1.5

As already mentioned in the previous chapter, each effect has

up to ve parameters (depending on the effect type) with which

you can adjust the effect. In each case it is possible to adjust one

parameter by using the BEAT push buttons. In most cases, this

is the BPM-synchronized parameter.

Effect parameters:

Press the PARAMETER push button 1) [47] to select a parame-

ter. This only works when the effect is deactivated (the FX ON

push button does not ash).

Alternatively, press the PARAMETER knob 2) [45] to select a

parameter.

Change the parameter value by turning the PARAMETER 3)

knob [45].

To switch to the next parameter, press PARAMETER 4) [45] or

[47] again.

Dry / Wet mix:

Turn the MIX knob = [44] slowly to the right to mix the effect

(Wet) to the original signal (Dry).

BPM-synchronized effect parameters4.1.6

Some of the effect sound especially interesting when time-related

parameters respond to the rhythm of the music. The DDM4000

supports editable, BPM-synchronized parameters.

Editing BPM-synchronized parameters:

Make sure that the BPM Counter calculates the correct value 1)

(if applicable, enter manually with TAP, see Chapter 4.2).

Change the parameter step-by-step with the BEAT push but-2)

tons [49]. The selected value appears on the display.

DELAY, ECHO:

For the delay and echo effect, you can edit the delay time in musical

units. The number of beats is displayed:

Beats and note values for delay and echoFig. 4.3:

A rhythmical representation of the whole looks like this (showing

a selection of several beats):

DIGITAL PRO MIXER DDM4000

BPM and Effects section20

Rhythmically represented delay parameterFig. 4.4:

FLANGER, PHASER, PAN, FILTER:

For the lter effect, the BPM synchronization is only possible in

LFO Mode. You can adjust the speed of the modulation

(LFO speed). The values 1 – 32 correspond to the number of beats

that are needed for one oscillation period:

Beats and note values for modulation effectsFig. 4.5:

The following picture results from the musical context:

LFO parameter, represented in beats and barsFig. 4.6:

FX Setup4.1.7

FX Setup lets you specify the crossover frequencies between the

individual bands of the EFFECT/BAND push buttons [46] – [48]

(Kill function on the effect path, see Chapter 4.1.2). This is indivi-

dually done for both effect devices.

Adjustable parameters:

FX1 LOW / FX2 LOW: Crossover frequency between LOW

and MID.

FX1 HIGH / FX2 HIGH: Crossover frequency between MID

and HIGH.

Press the left or right PARAMETER knob 1) [45] to select the

parameter for FX1 and FX2.

Turn the left or right PARAMETER knob to change the value 2)

of the selected value.

BPM Counter4.2

The Auto BPM Counter is automatically able to convert the tempo

of the track being played into BPM (Beats Per Minute). The detec-

ted BPM values are the basis for all time-related effect parameters

and for the recording duration of the sampler. The BPM can be

detected in two different ways: manually and automatically. In both

cases, the current BPM is shown in Section B of the display.

Automatically detecting beats with AUTO BPM:

The BPM Counter detects the tempo of the signal source assig-

ned to the Effect section. The signal source is shown in the BPM

section of the display. (Assigning the signal source to the BPM/

Effect section is described in Chapter 4.1.1.)

Make sure that “Auto BPM” is activated. When active, the 1)

AUTO BPM push button [50] shines yellow and the BPM

indicator ashes on the display.

Should Tap Mode be active (AUTO BPM push button +

shines blue), press the AUTO BPM push button longer

than one second to activate Auto BPM.

Now the BPM Counter determines the BPM value of the played 2)

signal. It is constantly brought up to date to be able to respond

immediately to any tempo changes.

Manually detecting beats with TAP:

Make sure that Tap Mode is activated. When active, the AUTO 1)

BPM/TAP push button [50] shines blue and the BPM indicator

shows “Manual.”

Tap the TAP push button 2) [50] (at least 2x) in the rhythm of the

music, which results in a constant BPM value. Here’s a tip:

while tapping, listen in on the signal using the headphones.

Should Auto BPM be active (AUTO BPM push button +

shines yellow), go to Step 2. When tapping the tempo,

Manual Mode is automatically activated.

The BPM value can always be readjusted by tapping over 3)

and over again.

The Auto BPM is always active when the device is +

turned on.

Without a music signal (or one which is too quiet), the +

BPM value ashes on the display. In addition, the mes-

sage “Low Level” appears on the display. The BPM value

also ashes when the beat cannot be clearly identied

(message “Uncertain”).

Page is loading ...

Behringer DDM 4000 Bundle II User manual

Brand: Behringer

Model: DDM 4000 Bundle II

Category: DJ controllers

Type: User manual

This manual is also suitable for

Download PDF

report

Behringer DDM 4000 Bundle II User manual

This manual is also suitable for

Behringer DDM 4000 Bundle II User manual

Related papers

Other documents