Clatronic HSMR 2757 Owner's manual

Page is loading ...

General Safety Instructions

• Read the operating instructions carefully before putting the appliance into ope-

ration and keep the instructions including the warranty, the receipt and, if possi-

ble, the box with the internal packing.

• The appliance is designed exclusively for private use and for the envisaged pur-

pose. This appliance is not fit for commercial use. Do not use it outdoors (except

if it is designed to be used outdoors). Keep it away from sources of heat, direct

sunlight, humidity (never dip it into any liquid) and sharp edges. Do not use the

appliance with wet hands. If the appliance is humid or wet, unplug it immediate-

ly. Do not put it in water.

• When cleaning or putting it away, switch off the appliance and always pull out

the plug from the socket (pull on the plug, not the cable) if the appliance is not

being used and remove the attached accessories.

• Do not operate the machine without supervision. If you should leave the work-

place, always switch the machine off or remove the plug from the socket (pull

the plug itself, not the lead).

• To protect children from the dangers posed by electrical appliances, make sure

that the cable is hanging low and that children do not have access to the appli-

ance.

• Check the appliance and the cable for damage on a regular basis. Do not use

the appliance if it is damaged.

• Do not try to repair the appliance on your own. Always contact an authorized

technician. To avoid the exposure to danger, always have a faulty cable be

replaced only by the manufacturer, by our customer service or by a qualified

person and with a cable of the same type.

• Use only original spare parts.

• Pay careful attention to the following “Special Safety Instructions“.

Special safety instructions for this device

• Use this machine to cut dry hair only.

• Use this machine to cut only hair and beards.

• The hair/beard cutting machine should never be used with wet hands.

• Do not charge the machine in a humid atmosphere.

• When charging keep the machine AWAY from direct sunlight or sources of heat.

• Do not press the cutting head too much against the skin. Danger of injury!

• NEVER use any adapter other than that supplied with the machine.

Use

Components: Accessories:

1. Cutting head 5. Connection socket 1. Comb

2. O/I selector 6. Charging station/ 2. Cleaning brush

3. Cutting length comb mounting 3. Special oil

4. Charging LED 7. Function ring 4. Scissors

32

GB

5....-05-HSM-R 2757 25.06.2003 10:39 Uhr Seite 32

Battery operation

You can use your hair and beard cutting machine with the battery once this has

been charged up. The device is partly charged when it leaves the factory. Please

charge the device for a period of 12 hours before using it for the first time. To char-

ge up the device, insert the plug of the power pack into a 230 V/50 Hz socket and

then connect the cable with the connection socket (5) of the charging station (6) or

directly with the device. Move the function switch to the "O" position. The maximum

length of the subsequent charge cycles is approximately 8 hours. When fully char-

ged the device has a maximum operating time of 25 minutes. After this time it must

be switched off and allowed to cool down for 10 minutes. The charging LED lights

up during the charging procedure.

Useful tips regarding battery life

Battery life can be lengthened by paying attention to the following instructions:

• Wait until the battery is almost completely flat before recharging.

• Never leave the machine connected to the charger for more than 24 hours.

• Charge the machine only with room temperature between 0 and +40°C.

Beard trimming and cutting

Shift the selector (2) to the I position. Start with the longest cutting level and trim

your beard gradually to the desired length.

Note: Lock the desired cutting length (cutting length comb) into place with the func-

tion ring (7).

released: It is now possible to adjust the cutting length comb

locked: Now you can cut your hair or beard with the length of the

cutting length comb that has been set

thinning function: The further you turn the function ring in the direction of the

thinning symbol, the fewer hairs are thinned out.

Hair cutting

Shift the selector (2) to the I position: Start with the longest cutting level and shor-

ten the hair gradually to the desired length.

Note: Lock the desired cutting length (cutting length comb) into place with the func-

tion ring (7).

Contour cutting and neck shaving

Remove the cutting length comb (3) and shift the selector (2) to the I position. Turn

the function ring (7) to the position. The shearing head enables the precise trim-

ming of the beard contours even areas, which are difficult to reach, and a clean

shaving of the hairline in the neck area.

33

GB

5....-05-HSM-R 2757 25.06.2003 10:39 Uhr Seite 33

Maintenance and care

The regular cleaning and maintenance of the machine will guarantee optimal

results and a long life.

• Use only a slightly damp and soft cloth to clean the machine.

• After use remove each time all hair left on the machine with the supplied brush.

• Remove the cutting comb and the cutting head to either blow off the hair

particles or brush them off with the cleaning brush.

• After using the machine apply each time 1-2 drops of an acid-free oil (sewing

machine oil) on the cutting head.

Attention: Please do not keep the hair cutter on charge for more than 24 hours.

This device has been tested according to all relevant current CE guidelines,

such as electromagnetic compatibility and low voltage directives, and has been

constructed in accordance with the latest safety regulations.

Subject to technical changes without prior notice!

Guarantee

The device supplied by our Company is covered by a 24 month guarantee starting

on the date of purchase (receipt).

During the life of the guarantee any fault of the device or its accessories *) ascriba-

ble to material or manufacturing defects will be eliminated free of charge by repai-

ring or, at our discretion, by replacing it. The guarantee services do not entail an

extension of the life of the guarantee nor do they give rise to any right to a new

guarantee!

Proof of the guarantee is provided by the proof of purchase. Without proof of

purchase no free replacement or repair will be carried out.

If you wish to make a claim under the guarantee please return the entire machine

in the original packaging to your dealer together with the receipt.

*) Damage to accessories does not mean automatic free replacement of the whole

machine. In such cases please contact our hotline. Broken glass or breakage of

plastic parts are always subject to a charge.

Defects to consumables or parts subject to wearing (e.g. motor pistons, kneading

blades, drive shafts, spare remote control, spare toothbrushes, saw blades, etc.) as

well as cleaning, maintenance or the replacement of said parts are not covered by

the guarantee and hence are to be paid!

The guarantee lapses in case of unauthorized tampering.

34

GB

5....-05-HSM-R 2757 25.06.2003 10:39 Uhr Seite 34

After the expiry of the guarantee

After the expiry of the guarantee repairs can be carried by the competent dealer or

repair service against the payment of the ensuing costs.

35

GB

5....-05-HSM-R 2757 25.06.2003 10:39 Uhr Seite 35

Page is loading ...

Clatronic HSMR 2757, hsm r 2757 Owner's manual

Related papers

Other documents