Chief KRA233PB Installation guide

Chief
Brand
Chief
Model
KRA233PB
Category
Wall & ceiling mounts accessories
Type
Installation guide

This manual is also suitable for

I N S T A L L A T I O N I N S T R U C T I O N S
KRA232
KRA233
Thin Client Storage Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KRA232/233
KRA232/233 Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
KRA232/233 does not exceed 3 lbs (1.36 kg).
WARNING: Use of this accessory will decrease the weight
capacity of the mounting system to which it is attached by the
combined weight of the accessory and all components
supported by this accessory. See Figure below for reference.
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
Installation Instructions KRA232/233
3
DIMENSIONS
8" MAX THIN CLIENT WIDTH
8"
MAX
THIN CLIENT
HEIGHT
8.21
208.6
8.07
205.1
KRA232B
DIMENSIONS: INCHES
[MILLIMETERS]
KRA232PB
DIMENSIONS: INCHES
[MILLIMETERS]
8" MAX THIN CLIENT WIDTH
8"
MAX
THIN CLIENT
HEIGHT
8.21
208.6
8.07
205.1
KRA232/233 Installation Instructions
4
DIMENSIONS (CONTINUED)
8" MAX THIN CLIENT WIDTH
8"
MAX
THIN CLIENT
HEIGHT
8.21
208.6
8.16
207.3
KRA233B
DIMENSIONS: INCHES
[MILLIMETERS]
KRA233PB
DIMENSIONS: INCHES
[MILLIMETERS]
8" MAX THIN CLIENT WIDTH
8"
MAX
THIN CLIENT
HEIGHT
8.21
208.6
8.16
207.3
Installation Instructions KRA232/233
5
LEGEND
TOOLS REQUIRED FOR INSTALLATION
PARTS
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Socket Wrench
Llave de cubo
Steckschlüssel
Chave de caixa
Chiave a brugola
Dopsleutel
Clé à douilles
1/8"
(included)
(security)
B (2)
#10-24 x 7/8"
J (1)
[Column guide]
E (1/2)*
[Thin client bracket]
F (1)
[32" connecting strap]
G (4)
[Adhesive-backed pads]
K (8)
[Pole clamp] L (1)
[Pole brace]
Hardware bag (1)
A (2)
#10-24 x 1/2" C (4)
#10-24 x 1/4"
(security)
D (1)
1/8"
(security)
H (1)
[Column brace]
Column kit (KRA232B/233B ONLY)
Pole kit (KRA232PB/233PB ONLY)
*QTY (KRA232/233)
KRA232/233 Installation Instructions
6
INSTALLATION
NOTE: The KRA232B and KRA233B thin client mounts are
compatible with the Kontour™ column mounts only.
Proceed to "Installation to Pole" Section for
KRA232PB or KRA233PB installation.
Installation to Column (KRA232B/233B)
1. Loosely attach thin client bracket (E) to column brace (H)
and column guide (J) using two #10-24 x 1/2" button head
cap screws (A). (See Figure 1)
Figure 1
NOTE: Thin client bracket (E) may be offset to either side by
using side holes. (See Figure 2)
Figure 2
2. Remove column cap from Kontour column. (See Figure 3)
3. Slide column guide (J) into column channel. (See Figure 3)
Figure 3
4. Tighten two #10-24 x 1/2" button head cap screws (A) when
desired height it reached. (See Figure 4)
5. Re-install column cap to column. (See Figure 4)
Figure 4
6. Proceed to "Thin Client Installation" Section.
1
(E)
(H)
(J)
(A) x 2
1
(E)
(H) (J)
(A) x 2
holes for left offset (right offset shown)
(J)
2
3
(A) x 2
5
4
Installation Instructions KRA232/233
7
Installation to Pole (KRA232PB/233PB)
1. Use two #10-24 x 7/8" button head cap screws (B) to install
thin client bracket (E) to pole clamp (K), pole brace (L) and
around pole. (See Figure 5)
Figure 5
2. Tighten two screws when desired installation height is
reached.
Thin Client Installation
NOTE: Thin client installation will vary depending on size and
style of device and user preference.
1. (Optional) Attach up to four adhesive-backed pads (G) to
inside of thin client bracket(s) (E) as desired. (See Figure 6)
Figure 6
2. (If applicable) Use hardware from thin client device to mount
device to bracket (E) using either 75mm or 100mm VESA
pattern. (See Figure 7)
3. Carefully place thin client device inside Thin client bracket
(E). (See Figure 8)
4. (Optional) Use 32" connecting strap (F) to secure thin client
device to thin client bracket (E). (See Figure 8)
Figure 7
Figure 8
KRA233 Models ONLY
5. Place second thin client bracket (E) on top of first thin client
bracket (E), lining up mounting holes. (See Figure 9)
6. Use four #10-24 x 1/4" security screws (C) to secure two
brackets (E) together. (See Figure 9)
Figure 9
1
(E)
(K)
(L)
(B) x 2
pole
(G)
thin client
device (example)
device
hardware
(not included)
2
3
4
(F)
thin client
device (example)
(C) x 4
6
5
(E)
KRA232/233 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-003112 Rev01
2019 Legrand | AV
www.legrandav.com
02/19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief KRA233PB Installation guide

Chief
Brand
Chief
Model
KRA233PB
Category
Wall & ceiling mounts accessories
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers