Eurolux F27W Owner's manual

Brand: Eurolux

Model: F27W

Type: Owner's manual

Table Fan

F27W

PRODUCT CODE

ILLUSTRATIONS

Please read instructions before commencing installation and retain for

future reference.

ENVIRONMENTAL PROTECTION

Waste electrical & Electronic equipment regulations requires that any of our products showing this

marking must not be disposed of with other household or commercial waste. To prevent possible

harm to the environment or human health from uncontrolled waste disposal, please separate any

such products from other waste types and recycle it responsibly at your local facilities.

Cape Town - 9 Racecourse Road, Milnerton, 7441

Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065

email: [email protected] web: www.eurolux.co.za

1. Front Guard

2. Spinner

3. Fan blade

4. Guard mounting nut

5. Rear guard

6. Motor housing

7. Oscillation Knob

8. Switch Button

9. Locking lug

10. Base surround

11. Screw

• Fitting Material: Plastic.

• Motor: 40W

• Voltage: 220V - 240V ~ 50Hz.

• Protection against electric shock: Class : 1 Requires earth connection.

• IP Rating: IP 20.Protected against solid foreign objects of 12.5mm and greater

Notf or outdoor user in wet conditions and areas of high humidity.

• Dimensions: F27: (H) 500mm X (W) 430mm X (D) 370mm

• Features: 3 Speeds

Rotation / Lockable

2 pull strings

1.6m Cable and plug top

Spare Blades X 889

SPECIFICATIONS ASSEMBLY INSTRUCTIONS

F21 - attachments:

If the external exible cable or cord of this luminaire is damaged, it should be exclusively replaced

by the manufacturer or his service agent or a similar qualied person in order to avoid a hazard.To

ensure that you get maximum longevity and maximum use out of your luminaire, please observe

the following safety instructions.

Electrical products can cause death, injury, or damage to property. Installation of the luminaire

must be carried out by a qualied electrician, in accordance with SANS 10142. On completion

of installation, ensure that the Certicate of Compliance is updated.

• Before connecting this luminaire, ensure that voltage indicated on the rating label corresponds

with the mains voltage in your home.

• When changing the lamp, ensure that the power is turned off.

• This luminaire is checked in full for conformity to the quality standards and safety requirements.

• The manufacturer / supplier is not responsible for any damage of properties and persons,

caused by the incorrect use or installation of the luminaire.

• Should you be unsure of how to install this luminaire correctly, please consult a professional

electrician or your supplier for assistance.

• Ensure all items/ components, threads and screws are tightly secured.

IMPORTANT:

• Tampering with this luminaire, IE. Using silicon sealers or incorrect cabling, will invalidate your

warranty. If one is not supplied within the carton, DO NOT use a solid speed control.

• Each blade set supplied is weighted and a complete set. If installing more than one fan, DO NOT

mix or add blades as this can cause your fan to wobble.

• Please check whether the connection of the power cord is safe and reliable before installation.

• Always ensure that the mains supply voltage is correct.

• Do not use the fan outdoors, in wet conditions or areas of high humidity.

• Do not insert objects or ngers through the bars of the grill.

• This appliance is not intended for use by young children or inrm persons unless they have been

adequately supervised by a responsible person.

• Always unplug the fan when cleaning or moving from one location to another.

• Always ensure that the fan is on an even, stable surface.

• To disconnect the appliance, unplug by rst turning off the mains power then unplugging the fan.

Do not pull on the cord ,always grap the plug.

IMPORTANT SAFEGUARDS

CLEANING

• Before cleaning always ensure the power supply is turned off and that the fan has

been unplugged.

• Do not immerse the fan in water.

• No abrasive products, solvents, detergent may be used to clean this fan.

• Ensure that the fan does not come in contact with corrosive chemicals, etc.

• Remove the front grill guard, blades and rear grill guard and wipe down parts with a damp cloth

to remove any dust.

• Ensure all parts are dry before reassembling your fan.

• The motor bearings are permanently sealed and do not require additional lubrication

• Ensure the fan is in the off position when plugged in.

• The fan should be placed on a at and stable surface when operating to avoid overturning.

The fan should not be placed in a damp place or where humidity is high (such as bathroom).

Push the oscillation knob to oscillate

Pull the oscillation knob to stop

Plug the power cord into a suitable socket

Tilt the head up or down to the required position by using a locking mechanism that will hold

the head in the desired position.

The fan is switched on using the push buttons on the base,

0 = Off,

1 = Low Speed,

2 = Medium Speed,

3 = High speed

Assembly of Base

1. This fan is supplied with a moulded surround which must be tted to the base of the fan

before the fan is used.

2. The moulded base surround is supplied with 3 off retaining screws

(in a small polybag taped to the inside of the surround)

3. Remove the bag containing the screws and position the surround on the moulded

retaining clips on the base and snap into place.

Ensure that the surround has clipped rmly into position onto the fan base and

screw the 3 retaining screws into the holes across the middle of the base.

Do not over-tighten these screws.

Assembly of Blade and Guard

1. Un-screw to remove the blade spinner from the motor shaft .

2. Un-screw the guard mounting nut from the front of the motor housing.

3. Position the rear guard against the front of the motor housing with the handle

uppermost,ensuring that the locating

pegs on the motor housing are engaged correctly in the holes in the guard.

4. Screw the guard mounting nut rmly onto the projecting thread on the motor housing,

make sure you tighten it rmly.

5. Remove and discard the PVC sleeve on the motor shaft.

6. Place the fan blade onto the motor shaft, locating the slot at the back of the blade on the

drive pin that pass through the motor shaft.

7. Screw the spinner onto the motor shaft, and tighten it rmly against the front of the blade.

8. Position the front guard against the rear guard so that the holes in the rims that accept the

small nut and bolt are in line. Insert the bolt through the holes and screw on the nut.

Do not fully tighten at this stage.

9. Move the guard retaining clips into position ensuring that they engage correctly on the rim of

the guard.

10. Fully tighten the small nut and bolt that passes through the rim of the guard.

Eurolux F27W Owner's manual

Eurolux F27W Owner's manual

Eurolux F27W Owner's manual

Related papers

Other documents