Qomo QWB100-WS-PS H01 Owner's manual

QOMO Hite Vision Interactive Whiteboard User Manual

0

Interactive Whiteboard

User Manual

Please keep this manual for future reference.

This is the general manual for the Interactive Whiteboard and there might be slight differences

QOMO Hite Vision Interactive Whiteboard User Manual

1

between the actual product and these descriptions.

Table of Contents

ATTENTION

SYSTEM REQUIREMENTS ............................................................................. 3

HOW TO INSTALL HARDWARE ....................................................................................... 6

HOW TO INSTALL SOFTWARE ...................................................................................... 13

SPECIFICATIONS ........................................................................................... 25

QOMO Hite Vision Interactive Whiteboard User Manual

2

Attention

 Do not expose this whiteboard to rain or moisture to reduce the risk

of fire or electric shock.

 Do not expose this whiteboard to fire, electric shock, or sunlight for

long periods of time.

 This device is heavy with a Net Weight over 15 kg (33 lbs). Use

expansion bolts to securely mount the device to the wall.

 When the projector and interactive whiteboard are used together, do

not stare directly at the light from the projector.

 This user manual is only applicable to IR interactive whiteboard

products.

 Only the matched pens from our company or human fingers can write

or operate on the interactive whiteboard.

 This product uses the IR annotation technology. Make sure the

product will not contact with any other hard objects to avoid

deformation of the board’s surface.

 If the interactive whiteboard is connected with a wire, make sure the

connection between this device and the computer is secure. It is

recommended that the wires are hidden to avoid pulling and

dragging the cables.

 If the interactive whiteboard is connected with a wire, use the cables

in the accessory box. Other cables might not be compatible with

this product.

 If the interactive whiteboard is connected by radio frequency, the

distance between the receiver and interactive whiteboard must not

exceed 15m (49 ft.). Avoid any obstacles which may shield the

electromagnetic waves.

 Do not touch, cut, or scratch the panel and frame with sharp or hard

objects. Do not drill holes or nail in any place of the product since it

will damage the device.

QOMO Hite Vision Interactive Whiteboard User Manual

3

 Please refer to the user manual for instructions on how to use the

interactive software.

System Requirements

Lowest Environmental Requirements：

 CPU: 1.0 GHz×86

 Memory: 256 MB

 Display Card: Support 256 or higher

 Hard Disk: 1 GB

 Screen Display Resolution：800×600, 1024×768, 1280×1024

 USB 1.1 Port

Recommended：

 CPU: 2.0 GHz×86

 Memory: 512 MB or higher

 Display Card: Support 256 or higher

 Hard Disk: 2 GB

 Screen Display Resolution：1024×768, 1280×1024

 USB 2.0 Port

Software Running Environment：Microsoft Windows XP/2003/Vista/7 32-bit

or 64-bit

QOMO Hite Vision Interactive Whiteboard User Manual

4

Introduction

This interactive whiteboard uses IR scan and sensor technology. Working

seamlessly with a projector and computer, the Interactive whiteboard can

become a large touch display. Any projected image on the whiteboard can

be operated by pens or fingers directly, thus providing an interactive

presentation platform for the presenter.

Main Performances：

 Writing：User can write and draw with pens or fingers directly on the

display panel and show your writing information instantly during a

presentation.

 Annotation：The user can operate and annotate over any format files

including .ppt, .doc, .xls, .avi, .mpeg, .jpeg, etc.

 Touching：In working mode, the interactive whiteboard can also be a

high precision touching interactive whiteboard. User can use their

fingers or a wand as a mouse to click and drag directly on the display

panel.

 Touch Recognition：The interactive whiteboard can recognize touch of a

single-finger, multiple fingers, double click, left click and right click.

 Hot Keys：Hot keys on one side or both sides of the board are used to do

functions within the annotation software.

 Smart Pen tray：The user can change pen writing stroke colors when

using the smart pen tray.

QOMO Hite Vision Interactive Whiteboard User Manual

5

 Driver Free Mode：This product design is in accordance with HID

category standard and supports driver free mode.

 Display Panel：The board has a high gain and high contrast display.

 Energy Conservation：Power consumption is less than 0.5W. There

isn’t a need for any independent power supply.

Note: On the upper left and bottom right corner on the board, there are projection area lines (such as

" "). When images are projected to the interactive whiteboard, the projection area should be

limited within these lines for better results when you are using the board.

QOMO Hite Vision Interactive Whiteboard User Manual

6

How to Install

The following instructions apply to the installation for all whiteboard products from our company. The

user can refer to corresponding instructions according to the products purchased. Please contact the

local distributor for more details.

How to Install Hardware

I．Whiteboard installation for A series

1. First install the smart pen tray of the interactive whiteboard：Insert the box

underprop into the pen tray. The PCB in the pen tray should be exactly in

the outlet of the underprop and the pen tray joints should be exactly in the

box underprop slot. Screw in two M3 screws from the bottom of the

pen tray. See the following diagram:

QOMO Hite Vision Interactive Whiteboard User Manual

7

2. Drill 8 holes for expansion bolts on the wall according to your preference

(Figure A). Install the wall-mount brackets and tighten the bolts into each

hole. Hang up the whiteboard with the calibration hole D in four corners

in the wall-mounting bolts (Figure B).

AB A

C

AB A

Figure A

QOMO Hite Vision Interactive Whiteboard User Manual

8

Figure B

QOMO Hite Vision Interactive Whiteboard User Manual

9

II．Whiteboard installation for B series

1．First install the smart pen tray of the interactive whiteboard：Lock the smart

pen tray to the metal supporting plate with three M5 bolts. See the following

diagram.

2．There are wall-mount brackets A and B on the back of the whiteboard. The

wall-mount brackets B should be screwed in. See the following diagram.

QOMO Hite Vision Interactive Whiteboard User Manual

10

Install the fixing plate according to the space between wall-mounts brackets

A：

After hanging up the whiteboard, drill 2 holes for expansion bolts according to

actual positions, and fix the wall-mount brackets B into the wall. See the

following diagram.

QOMO Hite Vision Interactive Whiteboard User Manual

11

QOMO Hite Vision Interactive Whiteboard User Manual

12

V．Interactive System Building

1. Make sure the whiteboard is firmly fixed before building the interactive

system.

2. Adjust the positions of the projector and whiteboard to make sure the

images are projected to writing area of the whiteboard in full screen

mode.

3. One corner of the whiteboard is set with a USB port (position of the USB

port will be varied in different models). Plug the USB cable into the USB

port. The USB cable in the accessory box is designed for this whiteboard.

Note: A normal USB cable might not be compatible to this whiteboard.

4. Connect the USB cable to the USB port in the computer.

5. Connect the computer and the projector (refer to the projector’s User

Manual for more details).

QOMO Hite Vision Interactive Whiteboard User Manual

13

How to Install Software

Before installing the software, temporarily disable the anti-virus or virus

protection software in your computer since it may affect the proper installation

of this software. The instructions in this manual are based on a Microsoft

Windows 7 system.

There is an installation disc in the accessory box. Insert the installation disc

and you will see the following instructions. You can open the disc manually if

you do not see the following:

Follow the instructions and complete the installation of the whiteboard

software. For complete functions, click the Full Installation button and

complete the installation as instructed. The computer needs to restart to

activate the software after the installation has completed.

QOMO Hite Vision Interactive Whiteboard User Manual

14

Calibration

The strokes on the whiteboard should coincide with actual ones, so

calibration is needed for proper functioning. The board needs to be

calibrated for the following situations.

 The whiteboard is used for the first time.

 The whiteboard software have been reinstalled or updated.

 The position of the whiteboard or projector is changed.

 The computer connected to the whiteboard is changed.

 The computer's resolution ratio or refresh rate is changed.

 Calibration deviation caused by other reasons.

How to calibrate:

Step 1：Connect all necessary devices and make sure the whiteboard service

program has been automatically launched once the computer’s power is on.

If not, click "Start-All Programs-QOMO-Flow!Works server" and run the

whiteboard service program. It will take a few seconds for the program to

load.

Step 2：A whiteboard driver icon will appear in the taskbar notification area.

The red dot in the icon will turn green to indicate that the board and the driver

are connected.

The service program icon has two statuses：A red icon indicates that the

whiteboard is disconnected. A green icon indicates that the whiteboard is

QOMO Hite Vision Interactive Whiteboard User Manual

15

connected and will work normally.

Step 3：Adjust the projection angle and make sure the projection area is

within the whiteboard display area.

Step 4：Left click on the whiteboard program icon at the bottom right of the

screen and you will see the following：

Click "Calibrate" and the calibration screen will be displayed：

Step 5：Follow the directions that are given on the board. Touch the center

of the flashing "十" with the interactive whiteboard pen tip or your finger. A

QOMO Hite Vision Interactive Whiteboard User Manual

16

status bar will appear to be filling up. Hold your contact there until the bar is

completely filled. Move to the next calibration point as directed and continue

with this process until the calibration is finished.

QOMO Hite Vision Interactive Whiteboard User Manual

17

Notes：

 Calibration with a finger might lead to inaccurate calibration. Calibration

with the pen tend to be more effective.

 Wrong calibration may lead to the whiteboard not working properly and

this requires recalibration.

 Pressing "ESC" during calibration can cancel the current calibration

operation.

 There are minor differences between the calibration interfaces of

different versions of the software. However, the calibration process is

very much the same. For products with shortcut keys on the board, there

are shortcut-key calibration steps at end of the calibration session.

QOMO Hite Vision Interactive Whiteboard User Manual

18

How to Use the Whiteboard

The whiteboard can be used after the calibration is finished. Common

computer operations can be launched and used by the simple touch of the

screen.

Left Click Tapping the whiteboard with a finger or a pen has the same

effect as a left click of a mouse.

Double Click Tapping the whiteboard twice in the same area with a

finger or pen has the same effect as a double click of a mouse.

Right Click Touching the whiteboard with a finger or pen for about

seconds has the same effect as a right click of a mouse.

Double click the Flow! Works annotation software icon on the desktop to run

the software.

You can do the following with the annotation software：

QOMO Hite Vision Interactive Whiteboard User Manual

19

Write You can write, draw, and erase with the pen by pressing and sliding

on the whiteboard.

Hand Rover Spread your palm and press the whiteboard with five

fingers at the same time and slide; this activates the hand rover function.

Note: The multi-touch whiteboard does not support this function. You can

contact the local distributor for more details.

Tools and Resources For a more detailed description of all of the

annotation software’s functions, tools, and resources, refer to the Flow!

Works user manual.

Key Notes：

 When using the rover feature, you need to have five fingers pressing the

whiteboard at the same time. Your fingers will be recognized as being

writing if they are not pressing at the same time.

 For the best writing results, use the pen in the accessory box to operate.

 To avoid scratching the surface, do not use other objects to write on the

board.

Page is loading ...

Qomo QWB100-WS-PS H01 Owner's manual

This manual is also suitable for

Qomo QWB100-WS-PS H01 Owner's manual

Related papers

Other documents