Uniden FMB321 Owner's manual

Uniden
Brand
Uniden
Model
FMB321
Type
Owner's manual

Uniden FMB321 is a marine radio flush mount bracket that provides a secure and professional-looking installation for your marine radio. It is compatible with a wide range of radio models, including Oceanus DSC, Polaris, Solara DSC, UM380, UM385, UM415, UM425, UM435, UM525, UM625, V50, V50B, VHF500, VHF500B, V60, V60B, VHF480, VHF490, VHF550, VHF580, VHF585, VHF595, VHF600, and VHF650. The bracket is made of durable materials and is designed to withstand the harsh marine environment. It is easy to install and comes with all the necessary hardware.

With the Uniden FMB321, you can be sure

Uniden FMB321 is a marine radio flush mount bracket that provides a secure and professional-looking installation for your marine radio. It is compatible with a wide range of radio models, including Oceanus DSC, Polaris, Solara DSC, UM380, UM385, UM415, UM425, UM435, UM525, UM625, V50, V50B, VHF500, VHF500B, V60, V60B, VHF480, VHF490, VHF550, VHF580, VHF585, VHF595, VHF600, and VHF650. The bracket is made of durable materials and is designed to withstand the harsh marine environment. It is easy to install and comes with all the necessary hardware.

With the Uniden FMB321, you can be sure

Marine Radio Flush Mount Bracket Instructions
Use a template...
Use the table below to nd the correct template and bracket for your radio. If you don’t see
your radio listed or don’t know the model number, you can measure the radio for yourself.
RADIO MODEL
USE
TEMPLATE
BRACKET PART #
MOUNTING HEIGHT MOUNTING WIDTH MOUNTING DEPTH
IN MM IN MM IN MM
Oceanus DSC # 4 FMB322B, FMB322W 2
3
/8 61 6
5
/8 168 6
1
/2 165
Polaris # 3 FMB321 2
1
/4 57 6
1
/8 156 6
11
/16 170
Solara DSC # 4 FMB322B, FMB322W 2
3
/8 61 6
5
/8 168 6
1
/2 165
UM380 # 1 FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
UM385 # 1 FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
UM415 # 1 FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
UM425 # 1 FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
UM435 # 1 FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
UM525 # 2 FMB321 3
1
/4 83 5
1
/2 140 5
1
/2 140
UM625 # 2 FMB321 3
1
/4 83 5
1
/2 140 5
1
/2 140
V50
V50B
# 1 50FMB, 50FMW,
FMB321
2
1
/16 53 5
11
/16 145 5
1
/4 133
VHF500
VHF500B
# 1 500FMB, 500FMW,
FMB321
2
1
/16 53 5
11
/16 145 5
1
/4 133
V60, V60B # 1 600FM, FMB321 2
1
/16 53 5
11
/16 145 5
1
/4 133
VHF480 # 1 600FM, FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
VHF490 # 1 600FM, FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
VHF550 # 1 500FM, FMB321 2
1
/16 53 5
11
/16 145 5
1
/4 133
VHF580 # 1 600FM, FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
VHF585 # 1 600FM, FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
VHF595 # 1 600FM, FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
VHF600 # 1 600FM, FMB321 2
1
/16 53 5
11
/16 145 5
1
/4 133
VHF650 # 1 600FM, FMB321 2
1
/16 53 5
11
/16 145 4
5
/16 110
The actual templates are on page 3. If you print the template page, do NOT select “Print to
Scale.” You must print actual size for the template to be accurate.
Mounting depth
mounting flange
Mounting height
bracket hole
Mounting width (widest part behind the mounting flange)
mounting flange
... or measure for yourself
Just measure the height, width, and depth behind
the radio’s mounting ange. (Be sure to measure
the widest part of the radio; the bracket holes might
be a little wider than the front of the radio.)
Use the template (or the height and width)
to cut the correct-sized hole for your radio.
Installing the radio
1) Make sure you have everything
Your ush-mount kit should contain the following hardware:
2 RIGHT ANGLE BRACKETS 2 FLAT BRACKETS 4 STOVE BOLTS
2 LOCK WASHERS 2 WASHERS 2 SLOTTED SCREWS 4 LOCK NUTS
You’ll also need
● a slotted (Phillips head) screwdriver
● pliers (or a wrench that ts the lock nuts)
● cutting tools appropriate for the material your dash is made of
2) Cut the hole where your radio should go
● Use the proper template or the mounting height and width to determine the
size of the hole (see other side).
● Be sure there is enough room behind your dash for the mounting depth to
t (see other side).
● Be sure you can reach behind the dash to attach the brackets and screws.
(You’ll have to do this from the back, so make sure your hands can t in
the space once the radio is already in place.)
● Be sure the power and antenna cables will still reach once the radio is
mounted.
● Be sure you use the recommended tools and follow all necessary
safety precautions when cutting the hole in your dash (these will vary
depending on the type of material, the thickness, etc.). Contact your boat’s
manufacturer or a professional installer if you aren’t certain.
3) Insert the radio
Pass any cables through the hole, then insert the radio until the mounting
ange is ush with the dash.
4) Attach the brackets to the radio
1. Align one of the right angle brackets so the large, single
hole lays at against the bracket hole in the side of
the radio and the two smaller holes
face the inside of the dash.
2. Place a washer over the hole in
the right angle bracket.
3. Thread a slotted
screw through a
lock washer.
4. Insert the screw
through the washer
and bracket and
into the bracket hole
on the side of radio.
5. Tighten the screw
securely.
6. Repeat this
procedure to attach
the other right angle
bracket to the other
side of the radio.
5) Secure the radio to the dash
1. Thread the lock nuts onto the
stove bolts; turn them until
they move up close to the bolt
head.
2. Place the at bracket against
the dash and align the dimples
with the holes in the right
angle bracket.
3. Insert the bolts through the
right angle bracket and into
the dimples on the at bracket,
then tighten the bolts securely.
4. Move the lock nuts down
the bolts until they touch the
bracket.
5. Use pliers or a wrench to
tighten the lock nuts against
the bracket.
6. Repeat this procedure with the other right angle bracket.
Radio front
Radio rear
Dash
(from rear
or inside)
Mounting
flange
Hole
Template #1
Template #2
Template #3
Template #4
TEMPLATES
Just measure the height, width, and depth behind the radio’s mounting ange. (Be sure to measure the
widest part of the radio: the bracket holes might be a little wider than the front of the radio.)
A NOTE ABOUT PRINTING THIS PAGE!
Be sure your printer is set to print at actual size. Do NOT select “Print to Scale.”
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Uniden FMB321 Owner's manual

Uniden
Brand
Uniden
Model
FMB321
Type
Owner's manual

Uniden FMB321 is a marine radio flush mount bracket that provides a secure and professional-looking installation for your marine radio. It is compatible with a wide range of radio models, including Oceanus DSC, Polaris, Solara DSC, UM380, UM385, UM415, UM425, UM435, UM525, UM625, V50, V50B, VHF500, VHF500B, V60, V60B, VHF480, VHF490, VHF550, VHF580, VHF585, VHF595, VHF600, and VHF650. The bracket is made of durable materials and is designed to withstand the harsh marine environment. It is easy to install and comes with all the necessary hardware.

With the Uniden FMB321, you can be sure

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents