DFI ST102-SD, ST102-CS, ST102-SD Installation Guide, ST102-SD/ST102-CS Installation Guide User manual

  • Hello! I am an AI chatbot trained to assist you with the DFI ST102-SD User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
ST102-SD Installation Guide
Package Contents
www.d.com
1 ST102-SD system unit
Mounting screws for Mini PCIe modules
Mounting screws
for M.2 modules
1 Quick Installation Guide
1 CD disk includes:
- Drivers / Manual
Panel
Rear View
Front View
DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and details of the
installation process, please refer to the user's manual.
LAN Ports
HDMI
USB 3.0
DC-in
DVI-D
(DVI-I connector)
DVD Drive
Power Button
Line-out
Mic-in
HDD LED
Power LED
USB 2.0
Notes:
The HDMI is a DP++/HDMI combo port but can only transmit HDMI signals (unless wired as a DP++ port).
Please plug in an HDMI cable with the right orientation and alignment to avoid damage to the connector.
You should feel resistance (due to a pin on the right) if the cable is not inserted correctly. Please see a video
at https://youtu.be/SUj07rfN5l8 for detailed instructions.
Align this edge with the
left side of the connector
Angled-corner
(up)
Angled-corner
Aligning side
(left)
pin
2
4. Slide the cover backwards to open the system.
The SODIMM sockets and
SATA drive bay are readily accessible after removing the chassis cover.
Removing the Chassis Cover
Installing internal components requires you to remove the chassis cover first.
Please observe the following guidelines and follow the procedure to open the
system.
1. Make sure the system and all other peripheral devices connected to it have
been powered off.
2. Disconnect all power cords and cables.
3. The 2 mounting screws on the rear side of the system are used to secure the
cover to the chassis. Remove these screws and put them in a safe place for
later use.
Mounting
screw
SATA drive bay
ODD drive bay
3
Installing a Memory Module
Grasp the module by its edges and align the memory’s notch with the socket’s
notch; then insert the memory into the socket at an angle and push it down
until you feel a click.
The system board is equipped with two memory slots. Please use the following
procedure to install SODIMM modules.
DIMM1
DIMM2
Notes:
1. The system supports dual-channel conguration. To enable dual-channel,
populate both SODIMM sockets.
2. If installing only one memory module, please install it on the memory socket
labeled DIMM1 (the one closer to the center of the board).
3. The SODIMM sockets can only accommodate DDR4 memory modules. Please
do not install other types of memory modules.
4
Installing a SATA Drive
The system can accommodate one 2.5” SATA drive. Please use the following
procedure to install a 2.5” SATA drive.
1. Remove the 2 mounting screws that secure the drive bay to the system.
Mounting screw
HDD bracket
Mounting screw
2. Align the mounting holes on the SATA drive with the mounting holes on the
HDD bracket.
SATA mounting screws
HDD bracket
Mounting screw
5
3. Use the mounting screws provided in the drive bay kit to attach the
HDD bracket onto the drive bay and secure the drive in place.
(on the drive bay’s bottom side)
HDD bracket mounting holes
HDD bracket mounting screws
Mounting screw
SATA mounting screws
6
4. Place the SATA drive bay back in the chassis and install the SATA drive bay
using the mounting screws you removed in step 1.
Mounting screw
SATA power/
data cable
5. Connect the SATA data/power cable to the SATA drive (refer to the
above picture). Make sure the other end of the SATA data/power cable
is connected to the connectors on the system board (refer to the picture
below).
SATA data
connector
SATA power
connector
7
Board Layout and Jumper Settings
Clear CMOS Data JP5
Normal 1-2 On (default)
Clear CMOS 2-3 On
www.d.com
A52801917
Auto Power-on Select JP1
Power-on via power button 1-2 On
(default)
Power-on via AC Power 2-3 On
Socket LGA1151
2
1
39
40
LVDS LCD Panel
Mini PCIe
mSATA
LAN 1
LAN 2
DC-in
DDR4_2 SODIMM
DDR4_1 SODIMM
DP
DVI-D
USB 3-4
USB 3.0
USB 1-2
USB 3.0
S/PDIF
1
10
9
Front Audio
2
1
Buzzer
1
2
Battery
Intel
H110
SPI Flash
BIOS
PCIe 1 (PCIe x4)
10
91
2 10
91
2 10
91
2 10
91
2
COM 2 COM 3 COM 4COM 1
1
1
SATA 0
SATA 3
9
12
10 9
12
10
USB
5-6
USB
7-8
SATA 3.0
1 2
1112
Front
Panel
Digital
I/O
1
USB 2.0
LCD/Inverter
Power
Standby
Power LED
1
1
System Fan 2
System Fan 1
1
1
CPU Fan
Digital
I/O Power
1
SATA
Power
51
62
65
21
3
1
1
1
1
1
1
2
5
6
SMBus
Auto Power-on
Select (JP1)
COM 1
RS232/Power
Select (JP2)
LCD/Inverter Power Select (JP7)
Backlight
Power
Select
(JP6)
Panel Power
Select (JP8)
(JP5)
(JP5)
Clear CMOS Data
ASMedia
ASM1442
ASMedia
ASM1442
Intel
WGI211AT
Chassis
Intrusion
ME Disable
1
1/7