3M Dynatel™ 1420EZ-Stand Operating instructions

Type
Operating instructions

3M Dynatel™ 1420EZ-Stand is a sturdy and reliable stand designed to hold 3M iD-Marker balls. It consists of six components: an upper level iD-Marker holding tray, a lower level iD-Marker holding tray, a stand stability holding tray, and three stand legs. The stand is easy to assemble, with color-coded labels to guide the user. It is made from High-Density Polyethylene (HDPE) and can be recycled. The stand is lightweight and portable, making it easy to transport and set up wherever it is needed. It is also durable and can withstand heavy use.

3M Dynatel™ 1420EZ-Stand is a sturdy and reliable stand designed to hold 3M iD-Marker balls. It consists of six components: an upper level iD-Marker holding tray, a lower level iD-Marker holding tray, a stand stability holding tray, and three stand legs. The stand is easy to assemble, with color-coded labels to guide the user. It is made from High-Density Polyethylene (HDPE) and can be recycled. The stand is lightweight and portable, making it easy to transport and set up wherever it is needed. It is also durable and can withstand heavy use.

3M
Dynatel
Writer Stand Assembly 1420EZ
Instructions
NOTE: Please visit www.3M.com/dynatel to download the full 3M
TM
Dynatel
TM
Writer Operators Manual 1420EZ. Once
at this website, go to Technical Documentation and then locate the manual under Operators Manuals.
The Dynatel
Stand 1420EZ consists of six (6) components (identified in illustration below);
1. “Item A” – One (1) Upper level iD-Marker holding tray
2. “Item B” – One (1) Lower level iD-Marker holding tray
3. “Item C” – One (1) Stand stability holding tray
4. “Item D” – Three (3) Stand legs
Assembly of components;
ATTENTION: Assure that the color label dots on “Items A, B and C” line up in the correct position, and that they are
facing upwards, as shown in the illustration below.
1. Slide “Item C” slot into the lower slot of one (1) “Item D” component.
a) Note that the lower slot in the “Item D” component is farther from the end of “Item D” than the upper slot.
(See illustration.)
2. Slide “Item B” slot into the middle slot, and “Item A” slot into the top slot, of the “Item D” component.
a) NOTE: It is imperative that the color dot labels on the top surfaces of “Item C”, “Item B” and “Item A” line up.
3. Slide the second (2nd) and third (3rd) “Item D” components into the appropriate slots on “Item A”, “Item B” and
“Item C”.
October 2014
78-9000-0121-1 3
PAGE 1 OF 2
ATTENTION: THESE THREE (3)
COLOR LABEL DOTS MUST BE
ALIGNED AND FACE UP.
ITEM "A"
ITEM "B"
ITEM "D"
ITEM "C"
Completed 3M™ Dynatel™ Writer Stand Assembly 1420EZ
-Shown with 3M Dynatel Writer Stand 1420EZ and 3M iD-Marker Balls
F CAUTION
To reduce the risks associated with falling/impact due to Stand Assembly break down:
DO NOT sit on, or over load, the Stand Assembly.
Note: This Stand Assembly is made from High Density Polyethylene (HDPE) and can be recycled per your local
regulations.
3M and Dynatel are trademarks of 3M Company.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable,
but the accuracy or completeness is not guaranteed.
Before using this product, you must evaluate it and determine if it is suitable for
your intended application.
You assume all risks and liability associated with such use.
Any statements related to the product which are not
contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless
expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture at the time of purchase.
3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the
3M product or refund the purchase price of the 3M product.
Except where prohibited by law, 3M will not be liable for any indirect,
special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3
Electrical Markets Division
6801 River Place Blvd.
Austin, TX 78726-9000
1-800-426-8688
http://www.3M.com/dynatel
Please Recycle. Printed in USA.
© 3M 2014. All Rights Reserved.
78-9000-0121-1 Rev B
PAGE 2 OF 2
  • Page 1 1
  • Page 2 2

3M Dynatel™ 1420EZ-Stand Operating instructions

Type
Operating instructions

3M Dynatel™ 1420EZ-Stand is a sturdy and reliable stand designed to hold 3M iD-Marker balls. It consists of six components: an upper level iD-Marker holding tray, a lower level iD-Marker holding tray, a stand stability holding tray, and three stand legs. The stand is easy to assemble, with color-coded labels to guide the user. It is made from High-Density Polyethylene (HDPE) and can be recycled. The stand is lightweight and portable, making it easy to transport and set up wherever it is needed. It is also durable and can withstand heavy use.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI