GETTING STARTED
1. Please read the safety section (page 2) in the main instructions before proceeding further. This section
contains vital information to ensure safe positioning and use of the TV
2. Unpack the TV and place on a flat level surface suitable to support the weight of the TV (15.7 kg .). This will require
two persons to lift the TV safely.
3. Connect the aerial into the TV Tuner connector at the rear of the TV (Fig 3).
Fig.2
4. Connect the mains power lead to the mains socket at the rear left side of the TV. (Fig
2 ) Plug in and switch on the TV at the mains supply. The LED indicator on the TV will
illuminate and show red (Fig 1).
5. Open the battery compartment cover (Fig 4) on the reverse of the remote control.
Insert 2 x AAA 1.5V alkaline batteries in accordance with the diagram in the battery
compartment. Take care to observe the correct polarity (+/-). Refit the battery
compartment cover
6. Press the POWER button (Fig 5) to turn the TV set on. The LED indicator will turn
green and after a few seconds, the screen will activate and the first time installation
menu (Fig. 6) will appear.
7. Use the cursor ▼/▲ buttons on the remote control to move up and down the display
to highlight desired options.
8. The default language is “English” if you want another language select that language
using the ►/◄ buttons and press OK.
9. Select AUTOTUNING and press OK. Fig 7 will be displayed, using the ▲/▼ buttons
select to country of use (UK is default). Select START and press OK, the TV will now
search the entire UHF range for both digital and Analog TV stations. See Fig 8. When
search is complete the TV will display the first channel (BBC1) in DVBt mode.
Fig.5
Fig 1
Fig.7
Fig.8
WATCHING TV (basic operation)
10. To select a channel either enter the number of the channel using the number
buttons on the remote control or scroll through the channels using the channel
CH+/- buttons.
11. To view analogue TV channels press the SOURCE button to display the source
menu. Using the cursor ▲ / ▼ buttons highlight TV on the menu and press OK to
select. To view digital TV channels select DTV on this same menu.
12. To check the list of channels stored, press the CH.LIST button to display the
channel list and use the cursor ▲ / ▼ buttons to move up and down the display.
To select a channel, highlight the channel on the list and press OK to confirm.
13. Adjust the volume to the desired level using the volume or cursor ◄ / ►buttons.
The sound can be silenced by pressing the MUTE button on the remote control
and a mute symbol will appear on the screen. Press the MUTE button a second
time to restore the sound.
14. To switch off the TV for short periods, press the POWER button. The TV will go
into standby mode and the LED indicator will change to red. If not using the TV
for extended periods turn off at the mains switch to conserve electricity, all
settings will be retained.
APLDVD2YR31568FD
MSD109
Quick Start Guide
Fig.6
Fig.3
Fig.4
DVD Operation
15. To select DVD operation press the SOURCE button to display the source menu. Using the cursor ▲ / ▼ buttons
highlight DVD on the menu and press OK to confirm.
16 Place a DVD or CD-R disc into the slot on the rightside of the Tv. (Fig 8). The disc must have the Label side facing
you and the Mirror side facing away. Do not handle the disc surface . Push the disc in gently and it will load
automatically.
Fig.8
17 The disc will now start to be “Read” and then, depending upon the type of disc, will play or display the disc menu or
disc contents. Select the item you wish to view, using the navigation buttons on the remote control and press “OK”.
18. To manually control DVD play you can use the control buttons located on the side panel (Fig 9).
Fig.9
For advanced operation of this TV and DVD player please consult the Instruction Manual.
Should you have difficulty in operating this unit, please consult the Trouble Shooting Guide in the
Instruction Manual. If you suspect a fault, please contact the Customer Help Line, details of which can
be found in the Instruction Manual.
19. When you wish to remove a disc, press STOP and then EJECT. Do not grip the disc to pull it out of the player, wait
until the disc stops moving before gripping the disc outer and removing carefully. See page 21 in the main manual
for correct handling of discs.
Label Side
1. Press to insert or eject disc from player.
2. Press. to play and pause disc. If paused press to restart playing.
3. Press to Stop disc playing.
For all other DVD functions use the Remote Control
Flat Screen
Although the Flat screen is made with high precision technology and 99.9% or more of the
pixels are effective, dots may appear. These can be black or bright dots (red, green or blue)
and may appear constantly on the Flat screen. This is a structural property of the Flat panel
and is not a malfunction.
/