GETTING STARTED
1. Please read the safety section (page 2) in the main instructions before proceeding further. This section
contains vital information to ensure safe positioning and use of the TV
2. Unpack the TV and place on a flat level surface suitable to support the weight of the TV (26.4 kg approx.). This will
require two persons to lift the TV safely. Remove the plastic film protecting the LCD screen
3. Connect the aerial into the TV Tuner connector at rear of the TV (Fig 2).
Fig.2
Fig.3
4. Connect the mains power lead to the mains socket at the rear right side of the
TV. Plug in and switch on at the mains and the switch at the front lower right
corner of the TV. The LED indicator on the TV will illuminate and show red (Fig
1).
5. Open the battery compartment cover (Fig 3) on the reverse of the remote
control. Insert 2 x AAA 1.5V alkaline batteries in accordance with the diagram in
the battery compartment. Take care to observe the correct polarity (+/-). Refit
the battery compartment cover
6. Press the POWER button (Fig 4) to turn the TV set on. The LED indicator will
turn green and after a few seconds, the screen will activate and the first time
installation menu (Fig. 5) will appear.
7. Use the cursor ▼/▲ buttons on the remote control to move up and down the
display to highlight desired options.
8. The default language is “English” if you want another language select that
language using the ►/◄ buttons and press ENTER.
9. Select OK and press ENTER. The TV will now search the entire UHF range for
both digital and Analog TV stations. See Fig 6. When search is complete the TV
will display the first channel (BBC1) in DVBt mode. If you Cancel the procedure
Fig 7 will be displayed.
Fig.4
Fig 1
Fig.6
Fig.7
WATCHING TV (basic operation)
10. To select a channel either enter the number of the channel using the number
buttons on the remote control or scroll through the channels using the channel
CH+/- buttons.
11. To view analogue TV channels press the SOURCE button to display the source
menu. Using the cursor ▲ / ▼ buttons highlight TV on the menu and press
ENTER to select. To view digital TV channels select DTV on this same menu.
12. To check the list of channels stored, press the ENTER button to display the
channel list and use the cursor ▲ / ▼ buttons to move up and down the
display. To select a channel, highlight the channel on the list and press ENTER
to confirm.
13. Adjust the volume to the desired level using the volume or cursor ◄ / ►
buttons. The sound can be silenced by pressing the MUTE button on the
remote control and a mute symbol will appear on the screen. Press the MUTE
button a second time to restore the sound.
14. To switch off the TV for short periods, press the POWER button. The TV will
go into standby mode and the LED indicator will change to red. If not using the
TV for extended periods turn off at the mains switch to conserve electricity, all
settings will be retained.
ADLTDVD3233
Quick Start Guide
Fig.5
DVD Operation
15. To select DVD operation press the SOURCE button to display the source menu. Using the cursor ▲ / ▼ buttons
highlight DVD on the menu and press ENTER to confirm.
16 Place a DVD or CD-R disc into the slot on the left side of the Tv. (Fig 8). The disc must have the Mirror side facing
you and the Label side facing away. Do not handle the disc surface . Push the disc in gently and it will load
automatically.
Fig.8
19 The disc will now start to be “Read” and then, depending upon the type of disc, will play or display the disc menu or
disc contents. Select the item you wish to view, using the navigation buttons on the remote control and press
ENTER.
20. To manually control DVD play you can use the control buttons located on the Left side panel (Fig 9).
Fig.9
For advanced operation of this TV and DVD player please consult the Instruction Manual.
Should you have difficulty in operating this unit, please consult the Trouble Shooting Guide in the Instruction
Manual. If you suspect a fault, please contact the Customer Help Line, details of which can be found in
the Instruction Manual.
21. When you wish to remove a disc, press STOP and then EJECT. Do not grip the disc to pull it out of the player, wait
until the disc stops moving before gripping the disc outer and removing carefully. See page 21 in the main manual
for correct handling of discs.
Flat Screen
Although the Flat screen is made with high precision technology and 99.9% or more of the pixels are effective, dots may
appear. These can be black or bright dots (red, green or blue) and may appear constantly on the Flat screen. This is a
structural property of the Flat panel and is not a malfunction.
Mirror Side
1. Press to insert or eject disc from player.
2. Press to play and pause disc. If paused press to restart playing.
3. Press to stop disc playing. Press once to “pre stop” press again to
fully stop.
4. Press to select next track or chapter.
5. Press to select previous track or chapter.
-
1
-
2
Akura APLDVD3221W HDID Quick start guide
- Type
- Quick start guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI