THIS MODULE IS PLUG-IN COMPONENT OF TOA 900 SERIES
AMPLIFIERS AND MIXERS.
JUMPER WIRE SETTING
M-01, 11, 21, 41, 51, 61: ALL THE MICROPHONE MODULES
COME WITH PHANTOM POWERING CAPABILITY. IF NOT
DESIRED, CUT J1 ON THE BOARD.
U-21: CUT J2 ON THE BOARD TO USE AS A REMOTE MASTER
VOLUME CONTROL UNIT. LEAVE J2 ON TO USE AS A
REMOTE-CONTROL AUX MODULE.
U-61: CUT J2 ON THE BOARD TO USE AS A MASTER
COMPRESSOR UNIT WHICH IS THEN CONNECTED BETWEEN
THE PREAMP OUT AND THE POWER AMP IN. IF AMPLIFIER
HAS LINK SWITCH. SET THE SWITCH TO OUT POSITION.
MUTING MODE SETTING
M-11: EITHER J3 OR J4 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
M-11, U-11, U-12, U-13, T-12: EITHER J5 OR J6 SHOULD BE
CUT. FOR PROPER OPERATION, REFER TO THE TABLE BELOW.
B-11, L-11: EITHER D3 OR D4 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
M-41, U-43: EITHER J5 OR J6 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
B-41: EITHER D3 OR D4 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
J3 J4 FUNCTION
ON ON NO OUTPUT SIGNAL.
CUT ON
NORMALLY "OFF", BECOMES " ON" WHEN MUTING
TERMINALS ARE CLOSED.
ON CUT
NORMALLY "ON", BECOMES "OFF" WHEN MUTING
TERMINALS ARE CLOSED.
CUT CUT WORKS AS REGULAR INPUT MODULE.
J5, D3 J6, D4 FUNCTION
ON ON
NORMALLY "ON", BECOMES "OFF" WHEN MUTE1
OR MUTE2 TERMINALS ARE CLOSED.
CUT ON
NORMALLY "ON", BECOMES "OFF" WHEN MUTE1
TERMINALS ARE CLOSED.
ON CUT
NORMALLY "ON", BECOMES "OFF" WHEN MUTE1
TERMINALS ARE CLOSED.
CUT CUT WORKS AS REGULAR INPUT MODULE.
J5, D3 J6, D4 FUNCTION
ON ON
OVERRIDES OTHER MODULES HAVING MUTE
FUNCTION IN MUTE1 AND MUTE2 WHEN ACTIVATED.
CUT ON
OVERRIDES OTHER MODULES HAVING MUTE
FUNCTION IN MUTE1 WHEN ACTIVATED.
ON CUT
OVERRIDES OTHER MODULES HAVING MUTE
FUNCTION IN MUTE2 WHEN ACTIVATED.
CUT CUT WORKS AS REGULAR INPUT MODULE.
133-21-216-9A
THIS MODULE IS PLUG-IN COMPONENT OF TOA 900 SERIES
AMPLIFIERS AND MIXERS.
JUMPER WIRE SETTING
M-01, 11, 21, 41, 51, 61: ALL THE MICROPHONE MODULES
COME WITH PHANTOM POWERING CAPABILITY. IF NOT
DESIRED, CUT J1 ON THE BOARD.
U-21: CUT J2 ON THE BOARD TO USE AS A REMOTE MASTER
VOLUME CONTROL UNIT. LEAVE J2 ON TO USE AS A
REMOTE-CONTROL AUX MODULE.
U-61: CUT J2 ON THE BOARD TO USE AS A MASTER
COMPRESSOR UNIT WHICH IS THEN CONNECTED BETWEEN
THE PREAMP OUT AND THE POWER AMP IN. IF AMPLIFIER
HAS LINK SWITCH. SET THE SWITCH TO OUT POSITION.
MUTING MODE SETTING
M-11: EITHER J3 OR J4 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
M-11, U-11, U-12, U-13, T-12: EITHER J5 OR J6 SHOULD BE
CUT. FOR PROPER OPERATION, REFER TO THE TABLE BELOW.
B-11, L-11: EITHER D3 OR D4 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
M-41, U-43: EITHER J5 OR J6 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
B-41: EITHER D3 OR D4 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
J3 J4 FUNCTION
ON ON NO OUTPUT SIGNAL.
CUT ON
NORMALLY "OFF", BECOMES " ON" WHEN MUTING
TERMINALS ARE CLOSED.
ON CUT
NORMALLY "ON", BECOMES "OFF" WHEN MUTING
TERMINALS ARE CLOSED.
CUT CUT WORKS AS REGULAR INPUT MODULE.
J5, D3 J6, D4 FUNCTION
ON ON
NORMALLY "ON", BECOMES "OFF" WHEN MUTE1
OR MUTE2 TERMINALS ARE CLOSED.
CUT ON
NORMALLY "ON", BECOMES "OFF" WHEN MUTE1
TERMINALS ARE CLOSED.
ON CUT
NORMALLY "ON", BECOMES "OFF" WHEN MUTE1
TERMINALS ARE CLOSED.
CUT CUT WORKS AS REGULAR INPUT MODULE.
J5, D3 J6, D4 FUNCTION
ON ON
OVERRIDES OTHER MODULES HAVING MUTE
FUNCTION IN MUTE1 AND MUTE2 WHEN ACTIVATED.
CUT ON
OVERRIDES OTHER MODULES HAVING MUTE
FUNCTION IN MUTE1 WHEN ACTIVATED.
ON CUT
OVERRIDES OTHER MODULES HAVING MUTE
FUNCTION IN MUTE2 WHEN ACTIVATED.
CUT CUT WORKS AS REGULAR INPUT MODULE.
133-21-216-9A
THIS MODULE IS PLUG-IN COMPONENT OF TOA 900 SERIES
AMPLIFIERS AND MIXERS.
JUMPER WIRE SETTING
M-01, 11, 21, 41, 51, 61: ALL THE MICROPHONE MODULES
COME WITH PHANTOM POWERING CAPABILITY. IF NOT
DESIRED, CUT J1 ON THE BOARD.
U-21: CUT J2 ON THE BOARD TO USE AS A REMOTE MASTER
VOLUME CONTROL UNIT. LEAVE J2 ON TO USE AS A
REMOTE-CONTROL AUX MODULE.
U-61: CUT J2 ON THE BOARD TO USE AS A MASTER
COMPRESSOR UNIT WHICH IS THEN CONNECTED BETWEEN
THE PREAMP OUT AND THE POWER AMP IN. IF AMPLIFIER
HAS LINK SWITCH. SET THE SWITCH TO OUT POSITION.
MUTING MODE SETTING
M-11: EITHER J3 OR J4 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
M-11, U-11, U-12, U-13, T-12: EITHER J5 OR J6 SHOULD BE
CUT. FOR PROPER OPERATION, REFER TO THE TABLE BELOW.
B-11, L-11: EITHER D3 OR D4 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
M-41, U-43: EITHER J5 OR J6 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
B-41: EITHER D3 OR D4 SHOULD BE CUT. FOR PROPER
OPERATION, REFER TO THE TABLE BELOW.
J3 J4 FUNCTION
ON ON NO OUTPUT SIGNAL.
CUT ON
NORMALLY "OFF", BECOMES " ON" WHEN MUTING
TERMINALS ARE CLOSED.
ON CUT
NORMALLY "ON", BECOMES "OFF" WHEN MUTING
TERMINALS ARE CLOSED.
CUT CUT WORKS AS REGULAR INPUT MODULE.
J5, D3 J6, D4 FUNCTION
ON ON
NORMALLY "ON", BECOMES "OFF" WHEN MUTE1
OR MUTE2 TERMINALS ARE CLOSED.
CUT ON
NORMALLY "ON", BECOMES "OFF" WHEN MUTE1
TERMINALS ARE CLOSED.
ON CUT
NORMALLY "ON", BECOMES "OFF" WHEN MUTE1
TERMINALS ARE CLOSED.
CUT CUT WORKS AS REGULAR INPUT MODULE.
J5, D3 J6, D4 FUNCTION
ON ON
OVERRIDES OTHER MODULES HAVING MUTE
FUNCTION IN MUTE1 AND MUTE2 WHEN ACTIVATED.
CUT ON
OVERRIDES OTHER MODULES HAVING MUTE
FUNCTION IN MUTE1 WHEN ACTIVATED.
ON CUT
OVERRIDES OTHER MODULES HAVING MUTE
FUNCTION IN MUTE2 WHEN ACTIVATED.
CUT CUT WORKS AS REGULAR INPUT MODULE.
133-21-216-9A
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
El Paso Chile Company DMS 3040-40 User manual
-
Electro-Voice 9003 Owner's manual
-
BURY AC 5120 Owner's manual
-
powersoft LiteMod 4HC User manual
-
Texas Instruments LMV1091 Noise Suppression Microphone Amplifier Evaluation Kit (Rev. A) User guide
-
JVC KS-LX200R User manual
-
ONKYO DV-BD507BCDC1N User manual
-
-
Roland M-400 User manual
-
