TOA HY-AH1 EU User manual

TOA
Brand
TOA
Model
HY-AH1 EU
Type
User manual

This manual is also suitable for

TOA HY-AH1 EU is a sturdy steel anchor hanging bracket designed to prevent the full weight of a flush-mounted ceiling speaker from directly applying to the ceiling panel. It offers secure and stable support for a variety of TOA ceiling speakers, including F-122C, F-2322C, F-2352C, and F-2852C models, which are known for their high-quality audio performance. This bracket is a valuable addition for ensuring the safe and optimal installation of your ceiling speakers, allowing you to enjoy clear and immersive sound while ensuring the longevity of your audio system.

TOA HY-AH1 EU is a sturdy steel anchor hanging bracket designed to prevent the full weight of a flush-mounted ceiling speaker from directly applying to the ceiling panel. It offers secure and stable support for a variety of TOA ceiling speakers, including F-122C, F-2322C, F-2352C, and F-2852C models, which are known for their high-quality audio performance. This bracket is a valuable addition for ensuring the safe and optimal installation of your ceiling speakers, allowing you to enjoy clear and immersive sound while ensuring the longevity of your audio system.

Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
HY-AH1ANCHOR HANGING BRACKET
INSTRUCTION MANUAL
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
CAUTION
1. SAFETY PRECAUTIONS
• Be sure to read the instructions in this section carefully before use.
• Make sure to observe the instructions in this manual as the conventions of safety symbols and messages
regarded as very important precautions are included.
• We also recommend you keep this instruction manual handy for future reference.
• Leave the installation to your TOA dealer because the installation requires expert knowledge. Improper
installation may cause the speaker to fall, resulting in personal injury and/or property damage.
• Install the mounting hardware in a location that can structurally support the weight of the mounting hardware
and the speaker. Doing otherwise may result in the speaker falling down and causing personal injury and/or
property damage.
• Do not use other methods than specified to mount the unit. Extreme force is applied to the unit and the unit
could fall off, possibly resulting in personal injuries.
• Tighten each nut and bolt securely. Ensure that the unit has no loose joints after installation to prevent
accidents that could result in personal injury.
• Use the specified speaker in combination. Doing otherwise may cause the speaker or component to fall off,
resulting in personal injury.
• Avoid touching the unit's sharp metal edge to prevent injury.
2. GENERAL DESCRIPTION
TOA's HY-AH1 Anchor Hanging Bracket is designed to be mounted to an anchor bolt to prevent the full weight
of a flush-mounted ceiling speaker from being directly applied to the ceiling panel. The ceiling reinforcement
ring which is supplied with the speaker is required when using the Anchor Hanging Bracket.
3. SPECIFICATIONS
Finish Steel plate, plating
Weight 700 g
Usable Speaker F-122C, F-2322C, F-2352C, F-2852C
Note: The design and specifications are subject to change without notice for improvement.
• Accessory
Paper pattern ................................... 1
Anchor bolt
Paper pattern
(accessory)
Ceiling panel
Hanging Bracket
mounting position
: 200 mm (7
7
/8")
Mounting hole
F-122C,
F-2322C,F-2352C
ø200 mm
(7
7
/8")
F-2852C
ø250 mm
(9
27
/32")
Width
Slot screws
Width
To shorten the width
of the bracket, push it
in the direction indicated
by the arrow to full stop.
To lengthen the width
of the bracket,
pull it in the direction
indicated by the arrow
to full stop.
Slot screws
4. INSTALLATION
Refer to the speaker's instruction manual for information.
[Mounting the F-122C, F-2322C or F-2352C speaker] [Mounting the F-2852C speaker]
Step 1. Loosen the four slot screws to adjust the HY-AH1's width.
Depending on the type of speaker to be mounted, adjust the width as shown in the figures below.
Note: Be sure to retighten the four slot screws after completing the width adjustment.
Step 2. Fix the Hanging Bracket to the anchor bolt.
2-1. The position of the upper anchor bolt nut
(the Hanging Bracket's mounting
position) should be 200 mm (7
7
/
8
") from
the ceiling surface.
Note: Use the supplied paper pattern to
determine the position.
Step 3. Mount the ceiling reinforcement ring (supplied with the speaker) to the Hanging Bracket.
Press the reinforcement ring firmly against the back side of the ceiling panel, and secure with the four
screws.
2-2. Mount the Hanging Bracket to the anchor bolt. Be sure to securely fix using double nuts.
Note: Before mounting, loosen the four reinforcement ring mounting screws to the point that they do
not fall out of their holes.
Anchor bolt
HY-AH1
200 mm
(7
7
/8")
Reinforcement ring
mounting screw
(4 screws)
The length of the anchor bolt end must be
shorter than 26 mm (1
1
/32").
If it exceeds this limit, the speaker will come
into contact with the end of the bolt,
preventing correct speaker installation.
Press against the ceiling panel.
Ceiling reinforcement ring
(supplied with the speaker)
Reinforcement ring
mounting screw
HY-AH1
Press against
the back side of the ceiling.
URL: http://www.toa.jp/
133-01-00118-00
  • Page 1 1
  • Page 2 2

TOA HY-AH1 EU User manual

TOA
Brand
TOA
Model
HY-AH1 EU
Type
User manual
This manual is also suitable for

TOA HY-AH1 EU is a sturdy steel anchor hanging bracket designed to prevent the full weight of a flush-mounted ceiling speaker from directly applying to the ceiling panel. It offers secure and stable support for a variety of TOA ceiling speakers, including F-122C, F-2322C, F-2352C, and F-2852C models, which are known for their high-quality audio performance. This bracket is a valuable addition for ensuring the safe and optimal installation of your ceiling speakers, allowing you to enjoy clear and immersive sound while ensuring the longevity of your audio system.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents