Infocus INA-SIMRINT1 User guide

Interactive Presentation System

1

www.infocus.com/SimpleShare

Models:

INA-SIMINT1

INA-SIMRINT1

English . Español . Français . Deutsche

- 2 -

1

2

3

4

Power DC : Insert Power Supply

LAN Port : Connect Ethernet cable

HDMI OUT : Connect to display device

Touch USB IN Port : Connect to a touch display

5

6

7

Status LED

Home button : Return to Home screen

Power Switch : Turn Receiver ON/OFF

Power DC

HDMI OUT

Touch USB IN Port

Power Switch

Home button

Status LED

LAN

Product Appearance

- 3 -

1

2

3

4

Installation

Connect HDMI cable from touch display to the HDMI OUT port of the

SimpleShare Interactive Presentation System Receiver.

Connect USB cable from touch display to the Touch IN USB port of the Receiver.

Connect the Power Supply provided to the Power In port of the Receiver.

Turn Power Switch On.

Step 1. Install Receiver

1

2

3

Power adapter

USB

HDMI

- 4 -

Installation

Step 2. Install Transmitter

1

2

3

4

5

Remove Touch USB Dongle from SimpleShare Interactive Presentation

System Transmitter.

Insert Touch USB Dongle into the USB IN port of your laptop or PC.

Plug SimpleShare Interactive Presentation System Transmitter in to the HDMI

out port of laptop or PC. Use the HDMI extension cable provided if needed.

Slide the power switch to the left to turn power ON and the Status LED

will light blue.

Click Transmit button and an image will appear on the display device of

which the Receiver is installed.

• If multiple Transmitters are connected, the corresponding screen of

the Transmitter that has just been clicked will appear, as part of the

product’s integrated switching function.

- 5 -

Pairing Receiver and Transmitters

1. Initial pairing

Pair the Transmitter with the Receiver by entering Set Mode in the Settings.

Ready for PAIRING

PAIR

- 6 -

Pairing Receiver and Transmitters

1. Initial pairing

Connect the Touch USB dongle to the

USB port of laptop or PC.

Press and hold the Transmit Button

while switching the power switch to ON.

Keep holding the Transmit Button

for ~10 seconds until status LED starts

1

2

When paired, the IP address will appear on the Set Mode Check window.

Click on the X button at the top right corner of the Set Mode

Check window to exit the setup procedure.

For additional Transmitters, repeat above procedure.

- Remove the USB Dongle from laptop upon setup.

- Upon each new Transmitter paired, please check that a new

IP address is added on the Set Mode Check window.

3

4

5

3

5

4

2

1

- 7 -

Pairing Receiver and Transmitters

2. Add/Remove Paired Transmitters

Click on the Add New Device Button to enter Set Mode

Click on Add New Device at the bottom of the Set Mode Check window to pair

additional

SimpleShare Interactive Presentation System Transmitter

.

Set Transmitter Color.

To remove a Transmitter that has already been paired, click on the X button to

the right of the paired Transmitter.

When all Transmitters have been paired, click on the X button at the top right

corner of the Set Mode Check window to exit the setup procedure

1

2

3

4

5

3

4

5

2

1

- 8 -

Click on the Add New Device Button to enter Set Mode.

Click on the Mac address of the Touch USB dongle to re-register within the Set

Mode Check window.

Connect the Touch USB dongle in a laptop to start pairing.

(Only one USB dongle shall be connected to laptop for new registration)

1

2

3

1

3

Pairing Receiver and Transmitters

3. Pair additional USB dongle

- 9 -

Pairing Receiver and Transmitters

3. Pair additional USB dongle

Click NEXT on the lower right corner of the yellow pop-up window

Check the Mac address of newly registered Touch USB dongle.

Click on the X button at top right corner of the Set Mode Check window to

exit the setup procedure.

4

5

6

4

6

5

- 10 -

Overlay Annotation

While mirroring, click on the overlay annotation icon to take notes and draw on

your display screen. This feature allows for full interactivity of your presentation.

Overlay annotation thumbnail

- Click on overlay annotation thumbnail to view on screen

2

1

3

4

6

5

2

1

2

3

4

5

6

3

1

2

Basic tools : pen, highlighter, eraser

Set line thickness

Add new page : save current page and add a new page

White board

Exit

Overlay Annotation Tool

- Tool Layout

3

- 11 -

Overlay Annotation

Notice

The distance available for wireless application may vary depending on the user

environment.

The wireless device in use may be subjected to radio interference during operation.

The screen in part may not show if the aspect ratio of image being replayed does

not match with that of the monitor.

Turn power OFF of the product and of the Transmitter when not in use.

- Pen Setting :

Click Select pen color, width

1 2

QR Code : Smart device QR Code reader

Smart device, SimpleShare Interactive Presentation System Receiver must be

5

- Share : Share via E-mail, QR-code Scan, Cloud

Choose color

Current color

Width

Erase entire screen

Select width

1

- Eraser :

Click

- 12 -

RF Exposure

* American National Standards Institute; National Council on Radiation Protection

and Measurements ; International Commission on Non-Ionizing Radiation Protection.

Your wireless device is a low power radio transmitter and receiver.

When it is on, it receives and also sends out radio frequency (RF) signals.

In August, 1996, the Federal Communications Commissions (FCC) adopted RF

exposure guidelines with safety levels for wireless device. Those guidelines are

consistent with the safety standards previously set by both U.S. and international

standards bodies:

ANSI C95.1 (1992) *

NCRP Report 86 (1986)

ICNIRP (1996)

Those standards were based on comprehensive and periodic evaluations of the

physicians from universities, government health agencies, and industry reviewed the

available body of research to develop the ANSI Standard (C95.1).

The design of your device complies with the FCC guidelines (and those standards).

This equipment should be installed and operated with minimum 20 cm between

the radiator and your body.

sistema de presentación interactiva

1

www.infocus.com/SimpleShare

Modelos:

INA-SIMINT1

INA-SIMRINT1

English . Español . Français . Deutsche

- 14 -

1

2

3

4

Alimentación DC : Inserte la Fuente de alimentación

Puerto LAN : Conecte el cable Ethernet

Salida HDMI : Conecte al dispositivo de visualización

Puerto Touch USB IN : Conecte al dispositivo Touch

5

6

7

Estatus LED

Botón de inicio : Vuelve a la pantalla de inicio

Interruptor de encendido :

Encienda/ Apaga el receptor

Características

Alimentación DC IN

ENTRADA USB táctil

Salida HDMI

Interruptor de encendido

Botón de inicio

Estatus LED

LAN

- 15 -

1

2

3

4

Instalación

Conecte el cable HDMI de la pantalla táctil al puerto de salida HDMI del

receptor SimpleShare Interactive Presentation System.

Conecte el cable USB de la pantalla táctil al Puerto Touch IN US del receptor.

Conecte la Fuente de alimentación suministrada al Puerto de entrada de

alimentación del receptor.

Encienda el interruptor de alimentación

Paso 1. Instalar receptor

1

2

3

Power adapter

USB

HDMI

- 16 -

Instalación

Paso 2. Instalar transmisor

1

2

3

4

5

Retire el Dongle USB Touch del transmisor SimpleShare Interactive

Presentation System.

Inserte Touch USB Dongle en el Puerto USB IN de su computadora portáti o PC.

Conecte el trasmisor SimpleShare Interactive Presentation System en el Puerto

de salida HDMI del ordenador portátil o PC. Utilice el cable de extensión HDMI

proporcionado si es necesario.

Deslice el interruptor de encendido a la izquierda para encender y el LED de

estado se encenderá en azul.

Haga click en el botón transmitir y aparecerá una imagen en el dispositivo de

visualización del cual está instalado el receptor.

• Si hay vario

s trasmisores conectados, aparecerá la pantalla correspondiente

del transmisor que acaba de hacer click, como parte de la función de

conmutación integrada del producto.

- 17 -

Emparejamiento de receptores y transmisores

1. Emparejamiento inicial

Ready for PAIRING

PAIR

- 18 -

Emparejamiento de receptores y transmisores

1. Emparejamiento inicial

Conecte el dongle USB Touch al Puerto

USB del portátil o.

Encienda el interruptor de alimentación

del transmisor SimpleShare Interactive

Presentation System.

1

2

Mantenga presionado el botón de transmisor durante ~ 10 segundos hasta que

el estado de LED empiece a parpadear en azul.

Cuando se emparejan, la dirección IP aparecerá en la Ventana de selección de

modo de ajuste.

Haga click en el botón X en la esquina superior derecho de la Ventana de modo

Para transmisores adicionales, repita el procedimiento anterior.

- En cada nuevo transmisor emparejado, compruebe que se ha agregado una

nueva dirección IP en la Ventana de selección de modo de ajuste.

3

4

5

6

2

1

3

5

4

- 19 -

Emparejamiento de receptores y transmisores

2. Agregar o quitar transmisores emparejados

Haga click en agregar nuevo dispositivo en la parte inferior de la ventana de

modo de ajuste para emparejar trasmisores SimpleShare Interactive Presentation

System adicionales.

Ajusta el color del transmisor.

Para eliminar un transmisor que ya ha sido emparejado, haga click en el botón

X a la derecha del emisor emparejado.

Cuando se hayan emparejado todos los transmisores, haga click en el botón

X en la esquina superior derecho de la Ventana de modo de ajuste para salir del

1

2

3

4

5

3

4

5

2

1

- 20 -

Haga click en la dirección MAC de la llave USB táctil para Volver a registrarla en

la Ventana de selección de modo de ajuste.

Conecte el dongle USB Touch en un ordenador portátil para iniciar el

emparejamiento. (Solo se conectará un dongle USB al ordenador portátil para el

nuevo registro)

1

2

3

Emparejamiento de receptores y transmisores

3. Empareje un dongle USB adicional

3

2

1

Page is loading ...

Infocus INA-SIMRINT1 User guide

This manual is also suitable for

Infocus INA-SIMRINT1 User guide

in other languages

Related papers

Other documents