Kelvinator JS4BE-KA User guide

JS4BE-KA
Kelvinator
Brand
Kelvinator
Model
JS4BE-KA
Type
User guide

This manual is also suitable for

*S4BE SERIES RESIDENTIAL SPLIT SYSTEM AIR CONDITIONER
Table 3. Unit Dimensions
MODEL
NUMBER
HEIGHT
(H)
WIDTH
(W)
DEPTH
(D)
*S4BE-018KA 27 1/2" 22 3/4" 22 3/4"
*S4BE-024KA 31 1/2" 22 3/4" 22 3/4"
*S4BE-030KA 27 1/2" 30 3/4" 30 3/4"
*S4BE-036KA 35 1/2" 30 3/4" 30 3/4"
*S4BE-042KA 39 1/2" 30 3/4" 30 3/4"
*S4BE-048KA 39 1/2" 30 3/4" 30 3/4"
*S4BE-060KA 43" 30 3/4" 30 3/4"
D
W
H
Model JS4BE Shown
Figure 1. Clearance Requirements
2” Mounting Pad
24" for
Service Access
12" or 18”
See Note
12" or 18”
See Note
DO NOT
OBSTRUCT
TOP OF UNIT
NOTE: Units require full perimeter clearances.
Installer must maintain 18” between two units
or 12” between single unit and structure.
6” from Building
or Structure
48”
14 SEER
Table 1. Electrical Specifications & Physical Data
MODEL NUMBER: *S4BE 018KA 024KA 030KA 036KA 042KA 048KA 060KA
ELECTRICAL
DATA
Volts-Cycles-Phase (1) 208/230-60-1
Total Amps 9.9 14.4 15.0 15.1 19.4 21.3 29.0
Delay Fuse Max. (2) 20 30 30 30 40 45 60
Min. Circuit Ampacity 12.1 17.7 18.5 18.6 23.9 26.3 35.6
CONDENSER
DATA
Coil
Area 10.0 11.7 15.2 20.3 22.8 22.8 25.4
Rows-FPI 1-23 1-23 1-18 1-18 1-18 1-18 1-23
Tube Dia MC
Fan Motor
Type PSC BLDC
Amps 0.9 0.9 0.9 1.0 1.5 1.5 2.6
HP 0.13 0.13 0.13 0.20 0.25 0.25 0.33
Compressor Data
RLA 9.0 13.4 14.1 14.1 17.9 19.8 26.4
LRA 48.0 58.3 73.0 77.0 112.0 109.0 134.0
RECOMMENDED REFRIGERANT SUCTION LINE O.D*
NOTE: Liquid line is 3/8” O.D. for entire length.
0-24 ft. 3/4” 3/4” 3/4” 3/4” 7/8” 7/8” 7/8”
25-39 ft. 3/4” 3/4” 3/4” 7/8” (3) 7/8” 7/8” 1-1/8” (4)
40-75 ft. 3/4” 3/4” 3/4” 7/8” (3) 7/8” 7/8” 1-1/8” (4)
REFRIGERANT CHARGE:
R-410A in ounces for outdoor unit, indoor unit and 15’ line set. (5)
39.0 45.0 51.0 62.0 75.0 101.0 81.0
APPROXIMATE WEIGHT (LBS.)
Net 107 127 132 146 175 177 221
Ship 113 134 140 155 184 186 230
(1) Operating Voltage Range: 187v min. — 253v max.
(2) HACR Type Circuit Breakers may be used.
(3) Requires 7/8" to 3/4" reducer from line to unit.
(4) Requires 7/8" to 1-1/8" reducer from line to unit.
(5) Additional charge for line sets above 15 feet. Values based on suction
line as follows with 3/8" liquid line.
(a) 3/4" = 0.6 oz. per additional foot.
(b) 7/8" = 0.7 oz. per additional foot.
(c) 1 1/8" = 0.8 oz. per additional foot.
* For other line set dimensions, refer to the Application Guidelines
for Refrigerant Lines Addendum.
Table 2. Control Wiring (24V)
WIRE GAUGE
RECOMMENDED MAXIMUM
WIRE LENGTH (FT) FROM UNIT
TO THERMOSTAT
22 45
20 70
18 115
16 180
QUICK REFERENCE DATA
2
Instructions:
1. Find the column for the model of outdoor unit that is being installed.
2. Find the row for the model of the indoor unit that is being installed.
3. Find the cell in the table in which this row and column meet. In this cell
the appropriate orifice / TXV and charge addition for this match are listed.
If the text in this cell is BOLD, then a change of orifice is necessary.
4. If a change in restrictor is necessary, then the appropriate restrictor will
already be supplied with the outdoor unit.
Examples:
• Forthe*S4BE-018KA/B6EMMX24K-Amatch,theappropriateTXVis
the 669564 and no additional charge needs to be added. (NO CHANGES
ARE NECESSARY)
• Forthe*S4BE-042KA/C7B(A,H)M03642(C,U)-B match, the 920671A
TXV Kit is needed as well as an additional 2 ounces of charge. (TXV KIT
ANDCHARGEADJUSTMENTNEEDED)
Table 4. REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW -SCFM)
ID RESTRICTOR INSTALLED WITH ID UNIT
MODEL NUMBER: *S4BE 018KA 024KA 030KA 036KA 042KA 048KA 060KA
OUTDOOR UNIT BOM CHARGE (OZ.) 39 45 51 62 75 101 81
MODELS
SUPPLIED
WITH ID
REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW -SCFM)
B6BM-X
B6BM-X24K-A 669564
669564
(18 / 600)
669564
(22 / 705)
-- -- -- -- --
B6BM-X24K-B 669564
669564
(18 / 600)
669564
(22 / 705)
-- -- -- -- --
B6BM-X30K-A 669565 -- --
669565
(27 / 875)
-- -- -- --
B6BM-X30K-B 669565 -- --
669565
(27 / 875)
-- -- -- --
B6BM-X36K-B 669566 -- -- --
669566
(36 / 905)
-- -- --
B6BM-X42K-B 669567 -- -- -- --
669567
(19 / 1225)
-- --
B6BM-X48K-C 669568 -- -- -- -- --
669568
(22 / 1450)
--
B6BM-X60K-C 669578 -- -- -- -- -- --
669578
(29 / 1660)
B6EM
B6EMMX24K-A 669564
669564
(0 / 540)
669564
(1 / 770)
-- -- -- -- --
B6EMMX24K-B 669564
669564
(0 / 540)
669564
(1 / 770)
-- -- -- -- --
B6EMMX30K-A 669565 -- --
669565
(2 / 1000)
-- -- -- --
B6EMMX30K-B 669565 -- --
669565
(2 / 1000)
-- -- -- --
B6EMMX36K-B 669566 -- -- --
669566
(13 / 1100)
-- -- --
B6EMMX42K-B 669567 -- -- -- --
669567
(0 / 1255)
-- --
B6EMMX48K-C 669852 -- -- -- -- --
669852
(0 / 1450)
--
B6EMMX60K-C 669578 -- -- -- -- -- --
669578
(3 / 1535)
B6EW
B6EW-X18K 669564
669564
(2 / 550)
-- -- -- -- -- --
B6EW-X25K 669564 --
669564
(3 / 820)
-- -- -- -- --
B6EW-X30K 669565 -- --
669565
(0 / 975)
-- -- -- --
B6EW-X36K 669566 -- -- --
669566
(4 / 1070)
-- -- --
NOTES:
• The charges listed are only valid for the standard 15’ lineset.
• Partnumbersbeginningwith669***areTXVpartnumbersandnumberslistedas0.***arerestrictordiameters.
3
Instructions:
1. Find the column for the model of outdoor unit that is being installed.
2. Find the row for the model of the indoor unit that is being installed.
3. Find the cell in the table in which this row and column meet. In this cell
the appropriate orifice / TXV and charge addition for this match are listed.
If the text in this cell is BOLD, then a change of orifice is necessary.
4. If a change in restrictor is necessary, then the appropriate restrictor will
already be supplied with the outdoor unit.
Examples:
• Forthe*S4BE-018KA/B6EMMX24K-Amatch,theappropriateTXVis
the 669564 and no additional charge needs to be added. (NO CHANGES
ARE NECESSARY)
• Forthe*S4BE-042KA/C7B(A,H)M03642(C,U)-B match, the 920671A
TXV Kit is needed as well as an additional 2 ounces of charge. (TXV KIT
ANDCHARGEADJUSTMENTNEEDED)
Table 4. REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW -SCFM) - Continued
ID RESTRICTOR INSTALLED WITH ID UNIT
MODEL NUMBER: *S4BE 018KA 024KA 030KA 036KA 042KA 048KA 060KA
OUTDOOR UNIT BOM CHARGE (OZ.) 39 45 51 62 75 101 81
MODELS
SUPPLIED
WITH ID
REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW -SCFM)
B6VM
B6VMAX24K-A 669564
669564
(18 / 555)
669564
(22 / 750)
-- -- -- -- --
B6VMAX24K-B 669564
669564
(29 / 555)
669564
(32 / 750)
-- -- -- -- --
B6VMAX30K-A 669565 -- --
669565
(27 / 980)
-- -- -- --
B6VMAX30K-B 669565 --
669565
(22 / 750)
669565
(27 / 980)
-- -- -- --
B6VMAX36K-B 669566 -- -- --
669566
(36 / 1100)
-- -- --
B6VMAX42K-B 669567 -- -- -- --
669567
(19 / 1250)
-- --
B6VMAX48K-C 669568 -- -- -- --
669568
(24 / 1400)
669568
(22 / 1435)
--
B6VMAX60K-C 669578 -- -- -- -- -- --
669578
(29 / 1600)
B6VMMX
B6VMMX24K-A 669564
669564
(0 / 540)
669564
(2 / 770)
-- -- -- -- --
B6VMMX24K-B 669564
669564
(0 / 540)
669564
(2 / 770)
-- -- -- -- --
B6VMMX30K-A 669565 -- --
669565
(2 / 1000)
-- -- -- --
B6VMMX30K-B 669565 -- --
669565
(2 / 1000)
-- -- -- --
B6VMMX36K-B 669566 -- -- --
669566
(9 / 1100)
-- -- --
B6VMMX42K-B 669567 -- -- -- --
669567
(0 / 1255)
-- --
B6VMMX48K-C 669568 -- -- -- -- --
669852
(0 / 1450)
--
B6VMMX60K-C 669578 -- -- -- -- -- --
669578
(3 / 1535)
NOTES:
• The charges listed are only valid for the standard 15’ lineset.
• Partnumbersbeginningwith669***areTXVpartnumbersandnumberslistedas0.***arerestrictordiameters.
709590A (Replaces 7095900)
Instructions:
1. Find the column for the model of outdoor unit that is being installed.
2. Find the row for the model of the indoor unit that is being installed.
3. Find the cell in the table in which this row and column meet. In this cell
the appropriate orifice / TXV and charge addition for this match are listed.
If the text in this cell is BOLD, then a change of orifice is necessary.
4. If a change in restrictor is necessary, then the appropriate restrictor will
already be supplied with the outdoor unit.
Examples:
• Forthe*S4BE-018KA/B6EMMX24K-Amatch,theappropriateTXVis
the 669564 and no additional charge needs to be added. (NO CHANGES
ARE NECESSARY)
• Forthe*S4BE-042KA/C7B(A,H)M03642(C,U)-B match, the 920671A
TXV Kit is needed as well as an additional 2 ounces of charge. (TXV KIT
ANDCHARGEADJUSTMENTNEEDED)
Table 4. REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW -SCFM) - Continued
ID RESTRICTOR INSTALLED WITH ID UNIT
MODEL NUMBER: *S4BE 018KA 024KA 030KA 036KA 042KA 048KA 060KA
OUTDOOR UNIT BOM CHARGE (OZ.) 39 45 51 62 75 101 81
MODELS
SUPPLIED
WITH ID
REQUIRED RESTRICTOR OR TXV
(CHARGE ADDITION (OZ) / RATED AIRFLOW -SCFM)
C6
C6B(A,H)-X24(C,U)-A 669564
669564
(18 / 550)
669564
(29 / 770)
-- -- -- -- --
C6B(A,H)-X24(C,U)-B 669681
669681
(18 / 550)
669681
(29 / 770)
-- -- -- -- --
C6B(A,H)-X30(C,U)-A 669565 -- --
669565
(27 / 950)
-- -- -- --
C6B(A,H)-X30(C,U)-B 669682 -- --
669682
(27 / 950)
-- -- -- --
C6B(A,H)-X36(C,U)-B 669683 -- -- --
669683
(36 / 1105)
-- -- --
C6B(A,H)-X42(C,U)-B 669684 -- -- -- --
669684
(26 / 1210)
-- --
C6B(A,H)-X48(C,U)-C 669852 -- -- -- -- --
669852
(22 / 1435)
--
C6B(A,H)-X48(C,U)-D 669852 -- -- -- -- --
669852
(22 / 1435)
--
C6B(A,H)-X60(C,U)-C 669686 -- -- -- -- -- --
669686
(22 / 1660)
C6B(A,H)-X60(C,U)-D 669686 -- -- -- -- -- --
669686
(22 / 1660)
C7-0
C7B(A,H)M01824(C,U)-A 0.048
920668A
(2 / 675)
920668A
(0 / 845)
-- -- -- -- --
C7B(A,H)M01824(C,U)-B 0.055
920668A
(2 / 675)
920668A
(0 / 845)
-- -- -- -- --
C7B(A,H)M03036(C,U)-A 0.061 -- --
920669A
(11 / 945)
-- -- -- --
C7B(A,H)M03036(C,U)-B 0.067 -- --
920669A
(11 / 945)
-- -- -- --
C7B(A,H)M03642(C,U)-B 0.071 -- -- --
920670A
(1 / 1110)
920671A
(2 / 1305)
-- --
C7B(A,H)M03648(C,U)-C 0.067 -- -- --
920670A
(1 / 1110)
920671A
(2 / 1305)
-- --
C7B(A,H)M048(C,U)-C 0.077 -- -- -- -- --
920672A
(1 / 1525)
--
C7B(A,H)M048(C,U)-D 0.087 -- -- -- -- --
920672A
(1 / 1525)
--
C7B(A,H)M060(C,U)-C 0.087 -- -- -- -- -- --
920673A
(0 / 1540)
C7B(A,H)M060(C,U)-D 0.087 -- -- -- -- -- --
920673A
(0 / 1540)
NOTES:
• Thechargeslistedareonlyvalidforthestandard15’lineset.
• Partnumbersbeginningwith669***areTXVpartnumbersand
numbers listed as 0.*** are restrictor diameters.
Specifications & illustrations subject to change
without notice or incurring obligations (11/13).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Kelvinator JS4BE-KA User guide

JS4BE-KA
Kelvinator
Brand
Kelvinator
Model
JS4BE-KA
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents