Kenmore Elite JVM1490WH02 Installation guide

Brand: Kenmore Elite

Model: JVM1490WH02

Type: Installation guide

This manual is also suitable for

Installation

Instructions

Abovethe

CooktopOven

JVM1490,SCA1000andSCA1001

I Questions? Carl 800-GE-CARES (800-432-2737) orvisit ore"Websit_ at: www.GEAppliances.com I

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Obsc_-_oall

governing codes and ordinances.

• Note to Installer _ Besure to leavethese

instructions with the Consumer.

• Note to Consumer - Keep these

instructions for future reference.

• Skill level - Installation of this appliance requires

basic mechanical and electrical skills.

• Proper installation is the responsibility of the installm:

• Product failure due to improper installation is not

covered under the Warranty.

I!! Ii

LA SECCION EN ESPAI_IOL

EMPIEZA EN LA PAGINA 25.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Instructions

CONTENTS

General information

Important Safety Instructions .................................. 3

Electrical Requirements .......................................... 3

Hood Exhaust ...................................................... 4, 5

Damage - Shipment/Installation .............................. 6

Parts Included .......................................................... 6

Tools You Will Need ................................................ 7

Mounting Space ...................................................... 7

Step-by-step installation guide

Placement of Mounting Plate ............................ 8-10

Rcmox_mg the Mounting Plate ...................... 8

Finding tile Wall Studs .................................. 8

Determining Wall Plate Location .................. 9

Aligning the Wall Plate ................................ 10

Installation Types .............................................. 11-22

_] Outside Top ............................

Exhaust

12-14

Attach Mounting Plate to Wall ............ 12

Preparation of Top Cabinet ................ 13

Checking for Proper Damper

Operation ............................................ 13

Mount the Oven ............................ 13, 14

Adjust the Exhaust Adaptor ................ 14

Connecting Ductwork .......................... 14

_] Outside Back Exhaust 15-18

Preparing Rear Wall for

Outside Back Exhaust .......................... 15

Attach Mounting Plate to Wall ...... 15, 16

Preparation of Top Cabinet ................ 16

Adapting Blower for Outside

Back Exhaust .................................... 16, 17

Mount the Oven .................................. 18

] Recirculating ........................................ 19-22

Attach Mounting Plate to Wall ............ 19

Preparation of Top Cabinet ................ 19

Adapting Blower

for Recirculation .......................... 20, 21

Mount the Oven ............................ 21, 22

Installing the Charcoal Filter .............. 22

Before You Use Your Oven .................................. 23

Secci6n en Espafiol ........................................ 2547

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded

outlet. The installer must peribrm a ground continuity

check on the power outlet box beibre beginning the

installation m insure that tile outlet box is properly

grounded, if not properly grounded, or if the

outlet box does not meet electrical requirements

noted (under ELECTRICAL REQUIREMENTS),

a qualified electrician should be employed to

correct any deficiencies.

CAUTION: For personal

safety, remove house fuse

or open circuit breaker

before beginning installation

to avoid severe or fatal

shock injury.

CAUTION: For personal safety, the momaling surface

must be capable of supporting the cabinet load, ha

addition to the added weight of this 63-85 pound

product, plus additional oven loads of up to 50 pounds

or a total weight of 113-135 pounds.

CAUTION: For personal safety, this product cannot

be installed ha cabinet arrangements such as an island or

a peninsula. It must be mounted to BOTH a top cabinet

AND a wall.

NOTE: For easier installation and personal safety, it is

recommended that two people install this product.

IMPORTANT--PLEASE READ CARF_UIIY. FOR

PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR

FATAL SHOCK.

The power cord of this appliance is equipped with

a three-prong (grounding)

plug which mates with

a standard three-prong

(grounding) wall receptacle

to minimize the possibility

of electric shock hazard

from this appliance.

insureproper

groundexists

beforeuse

You should have the wall receptacle and circuit checked

by a qualified electricima to make sure the receptacle is

properly grounded.

Where a standard two-prong wall receptacle is

encomatered, it is very important to have it replaced

with a properly grounded three-prong wall receptacle,

installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,

DEFORM, OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH

AN EXTENSION CORD.

ELECTRICAL

REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 15 amps, and

1.70 kilowatts. This product must be connected to

a supply circuit of the proper voltage and fi'equency.

Wire size must conform to the requirements of the

National Electrical Code or the prevailing local code

for this kilowatt rating. The power supply cord and

plug should be brought to a separate 15 to 20 ampere

branch circuit single grounded outlet. The outlet box

should be located in the cabinet above the oven. The

outlet box and supply circuit should be installed by

a qualified electrician and conform to the National

Electrical Code or the prevailing local code.

Installation Instructions

HOOD EXHAUST

NOTE: Read these next two pages only if you plan to vent your exhaust to the outside.

If you plan to recirculate the air back into the room, proceed to page 6.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The fbllowing chart describes an example of one possible

ductwork installation.

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

RoofCap 24 Ft. x (1) = 24 Ft.

12Ft.StraightDuct 12Ft. x (1) = 12Ft.

(6" Round)

Rectangular4o-Round 5Ft. x (1) = 5Ft.

TransitionAdaptor*

Equivalentlengthsofductpiecesarebasedonactualtestsand

reflectrequirementsfor goodventingperformancewith anyventhood.

Total Length = 41 Ft.

*IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper

will have to be cut to fit, using the tin snips, in order to allow fi'ee movement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible

ductwork installation.

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH* x USED = LENGTH

_,.....__ WallCap 40Ft. x (1) 40Ft.

3 Ft.StraightDuct 3 Ft. x (1) 3 Ft.

37g"x 10"Rectangular)

90° Elbow 10Ft. x (2) 20Ft.

Equivalentlengthsof ductpiecesarebasedonactualtests and

reflectrequirementsforgoodventingperformancewith anyvent hood.

Total Length = 63 Ft,

NOTE: For back exbaust, care sbould be taken to align exhaust witb space between studs, or wall should be prepared

at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

Installation Instructions

NOTE: If you need to install ducts, note that the total

duct lengtb of 3¼" x 10" rectangular or 6" diameter

round duct should not exceed 140 equivalent feet.

Outside ventilation requires a HOOD EXHAUST DUCT.

Read tile following carefully.

NOTE: It is important tbat venting be installed using

the most direct route and with as few elbows as possible.

This ensures clear venting of exhaust and helps prevent

blockages. Also, make sure dampers swing freely and

nothing is blocking the ducts.

Exhaust connection:

The hood exhaust has been designed to mate witb

a standard 3¼" x 10" rectangular duct.

If a round duct is required, a rectangular-to-round

transition adaptor must be used. Do not use less than

a 6" diameter duct.

Maximum duct length:

For satisfhctory air movement, the total duct length of"

3¼" x 10" rectangular or 6" diameter round duct should

not exceed 140 equivalent feet.

Elbows, transitions, wall and roof caps, etc.,

present additional resistance to airflow and are equivalent

to a section of straight duct which is longer than their

actual physical size. When calculating the total duct

lengtb, add tbe equivalent lengtbs of all transitions and

adaptors plus tbe length of all straight duct sections.

The chart below shows you how to calculate total

equivalent ductwork length using the approximate feet

of equivalent lengtb of some typical ducts.

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

Rectangular_to-Round 5 Ft. x ( ) Ft.

TransitionAdaptor*

Wall Cap 40 Ft. x ( ) Ft.

(i)_ 9O°EIbow lOFt. x ( ) Ft.

(_ 45° Elbow 5 Ft. x ( ) Ft.

90° Elbow 25 Ft. x ( ) Ft.

45° Elbow 5 Ft. x ( ) Ft.

RoofCap 24 Ft. x ( ) Ft.

StraightDuct6" Roundor 1 Ft. x ( ) Ft.

3¼" x 10"Rectangular

Total Ductwork = Ft.

* IMPORTANT: if a iectangtflm_to-round transition Equiwflent lengths of duct pieces are based on actual tests and

adaptor is used, the bottom cornm_ of the damper reflect requirements for good venting performance with any

_'iU ha_e to be cut to fit, t_sing the tin snips, in _ent hood.

order to aUo_ fi'ee inovement of the damper.

Installation Instructions

DAMAGE - SHIPMENT/

INSTALLATION

" If the unit is damaged in shipment, return tile

unit m the store in which it was bought J[br repair

or replacement.

" If the unit is damaged by the customer, repair or

replacement is the responsibility of the customer.

" If the unit is damaged by the installer (if other

than the customer), repair or replacement must

be made by arrangement between customer and

installmz

PARTS INCLUDED

HARDWARE PACKET

PART QUANTITY

WoodScrews 2

(I/4_1 X 2")

I\ Togg{eBolts(and 4

_ wingnuts)(_A"x3")

Se{f-a{igningMachine 3

Screws(IA"_28x 3_A")

NylonGrommet 2

(formetalcabinets)

ExhaustAdaptor 1

_ Damper 1

Metal Screws 1black

(IA"x *A") 2bronze

PowerCordStrap 1

(plastic)

You will find the installation hardware contained in

a packet with the unit. Check to make sure you have

all these parts.

NOTE: Some extra parts are included.

PARTS INCLUDED

ADDITIONAL PARTS

PART

_ _msEr w

TopCabinet

Template

RearWall

Template

Installation

Instructions

Sepamtely

Packed

Grease

Filters

QUANTITY

Installation Instructions

TOOLS YOU WILL NEED

# I o_d#2 Phifiipsscrewdriver

Pencil

Ruleror 1:apemeasure

figh[ edge

{ep[i_nal)

_n snips {fer [:u[[ill[_

Gloves

Sofe_goggles

_cissers

Electricdrillwi[h :_(", _i(',

_" a_d_" driftbi[s Fillerblocks_r scrap

weedpieces,ifileeded

fer [epcabine[spacfl_g

(usedonrecessedbottom

cebfl_etfl_stallotiensonly)

Studffl_der or

Ductandmaskingtape

Level

MOUNTING SPACE

plosh

NOTES:

" _I_e space between dm cabinets must be NY" wide

m_d tYee of' obstructions.

" If the space between the cabinets is greater

than BO", a Filler Panel Kit may be used to fill

in ti_e g_ap between lhe oven and the cabinets.

}%ar (_cr's ManuN contains the kit number

tbr your model.

• This oven is tbr installation over ranges tip m

36" wide,

" If you are going m vent your oven m lhe outside,

see Hood Exhaust Section tbr exhaust duct

preparation.

•When installing the oven beneath smooth, flat

cabinets, be care[_l to follow the instruc_ons

on the top cabinet template For power cord

clearance.

Installation Instructions

PLACEMENT OF THE MOUNTING PLATE

[] REMOVING THE OVEN FROM

THE CARTON/REMOVING THE

MOUNTING PLATE

[]Remove the box conudning the instMlation

instructions, filters, exhaust adaptm; damper

and the small hardware bag. Do not remove

the Styrofbam protecting the fl:ont of the oven,

[] Fold back all 4 carton flaps fully against c_u'ton

sides. Then carefully roll 0_e oven and era:ton over

onto the top side. The oven should be resting in

the Styrofbam.

[] Pull Ihe car_on up and off the oven.

[] The motmting plate is attached to the back of the

oven. Remove the two screws holding it to the oven,

The plate will be used as the rear wall template and

fbr mounting the oven to the wall.

[] Set the oven upright. Remove and properly discard

plastic bags and Styrofbwn.

[] Open the oven door and remove 1he st}rotbarn

pack Dora inside the oven. Remove Ihe tape

covering the tumlable hub,

[-_ FINDING THE WALL STUDS

[] Find the studs, using one of the fbllowing

methods:

A. Stud finder - a magnetic device which

locates nails.

B T

• Use a hmnmer to tap lightly across the

mounting surfhce to find a solid sound,

This will indicate a stud location,

[] After locating Ihe stud(s), tind the center by

probing Ihe v#all with a sm_dl nail to find the

edges of the stud, Then place a mark halgva)

between the edges. The center of any _ljacent

studs should be 16_"or- 24" fi'om Ibis mark,

]Draw a line down the center of the studs,

THE OVEN MUST BE CONNECTED TO AT LEAST

ONE WALL STUD•

Installation Instructions

[] DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Plate position - beneath flat bottom

cabinet

Plate position - beneath framed recessed

cabinet bottom

Maunth_gPI_teTabs

Moum:ingPlateTabs

Teuchi_gthe Back

Frame

Plate position - beneath recessed bottom

cabinet with front overhang

30" to Cooktap

S%ur cabinets may have decorative trim that intertcres

with d_e oven inst_dlation. Remove the decorative n'im

to install the oven properI_ and to make it level.

THE OVEN MUST BE LEVEL.

Use a l_'eI to make sure the cabinet bottom is level.

If' the cabinets have a lyon t overhang only, Mth no

back or side &ame, install the moundng plate down

the same distance as the &ont ore€hang depth. This

will keep the oven level.

[] Measure the inside depth of the fl'ont overhang.

[] Draw a horizontal line on Ihe t_ck _vall

eqt_]

all

distal_ce below the c_binet bottom ;_ the inside

depth of the fi'ont ove_:hal_g.

[] For I}fis t}_e of inst_dlation with front

overhal]g onl}_

align Ihe moundng u4bs with Ih:is horizonud line, not

touching the cabinet tx_ttom as descrit_d in Step D.

Installation Instructions

[] ALIGNING THE WALL PLATE

HoleC _ 0 0 0 0 b 0000000000

0 0 0 O 0 OI 0000O 000

CAUTION: Wear gloves

to avoid cutdng fingers on

sharp edges,

Area E

HoleD

Draw a ve*_ictd line on the wall at (he center of the

[]

3(Y' wide space.

[] Use (he mounting plate as the template [br (he rear

wtdl. Place the mortaring plato on the wall, making

sttre lhat the tabs are touching the bottom o1' the

cabinet or the level llne dl_awn in Step C [or cabinets

with [font overhang. Line up the notch and center line

on the monnting plate to the center line on the wall.

[] Dc]ai[e holding (he mounting plate with one hand,

draw circles on (he wall tat holes A, B, C and D (see

illustration aboveiactuM plate marked with an:ows).

Fore* holes mttst be used for mounting,

[]

NOTE: Holes C and D are inside area E. ff neilher

C nor D is in a stud, find a stud som_here in area E

and draw a fifth circle to Iine up M(I_ (he stud. It is

imporlant to tt_ at least one wood screw mortared

firmly in a stud to support the weight of the oven.

Set the mounting plate aside.

Drill holes on 1he circles. K there is a stud, drill a _a"

hole tbr wood screws. For holes that don't line up wifl_

a stud, drill a %" hale tbr toggle bolts.

NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.

Installation Instructions

INSTALLATION TYPES (Choose A, B or C}

This oven is designed fbr adaptation to the fbllowing

3 t}pes of ventilation:

A_Outside Top ExhatJst (Vertical Duct)

B÷Outside Back Exhaust (Horizontal Duct)

C. Recirculatmg (Non-Vented Ductless)

NOTE: This oven is shipped assembled fbr Outside Top

Exhaust, Select 1he t)pe ofventiIadon required fbr your

installation and proceed to that section,

OUTSIDE TOP EXHAUST

(VERTICAL DUCT}

OUTSIDE BACK EXHAUST

(HORIZONTAL DUCT}

RECIRCULATING

(NON-VENTED DUCTLESS}

A Charco;d Filter i_cessory

Kit is required tor the

non-vented exhaust, (See your

(_er's ManuN fbr the kit

numbe_:)

Installation Instructions

OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

AI÷ Attach Mounting Plate m Wal]

A2. Prepare "Fop Cabinet

A3. Install sL_apter

A4. Moant Oven

A_. Adjust Exhat_st Adaptor

A6. Connect Ductwork

ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate to the wtdl rising toggle bolts,

At least one wood screw most be osed to attach the

p]ate to a wall stud,

[] Remove the toggle win_ ti'om the bolts.

[] Insert the bolts into the mounting plate through

the holes designated to go into dD_dl and

reattach tile toggle wings to %_"onto e_ch bolt.

To use toggle bolts:

Sp_cin__orIo,agles

MoreThanWoll

_l,,,_Thickn ess

Iro_leWin_s

Mou_tin_ IIl, lJ /To!NI'_ II II

BoltEnd

[] Place the mounting plate against the wall m_d

insert the toggle wings into the holes in the wal]

to mount the plate.

NOTE: Befbre tightening toggle bolts and wood

screw, make sure the tabs on the mounting plato

touch the bottom of the cabinet when pushed

flush against (he wMl and (hat the plato is properly

centered trader the cabinet,

CALrTION: Be carefuI to avoid pinching fingers

between the back of' the moondng plate and the wM1.

_ Tighten all bolts. Pull the p]ate away fi'om the wM1

to help tighten the bolts,

Installation Instructions

[-_ USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes fbr the top support screws,

a hole large enough fbr 1he power cord to fit through,

and a cutout large enough fbr the exhaust adaptor:,

• Read the instructions on the TOP CABINET

TEMPIJVFF.

• Tape it underneath the top c_4binet.

• Drill the holes, fblloMng the instructions on the

TOP CABINET TEMPIATE.

CAUTION: Wear s_4"et}goggles When dfilEng holes

in the cabinet bottom.

[-_ ASSEMBLE AND

INSTALL ADAPTOR

[_ Place the oven in its upright position, with the top

of the unit tacing up.

[] Insert 0_e tabs on each side of 0_e damper into the

holes at the inside *:ear:of the adaptor.

_ Attach the exhaust adaptor to the blower plate with

the two bronze metal screws provided.

Make salre that the damper pivots easily before

mounting oven.

_'_u wit1 need to make adjusmaents to asstu'e proper

_dignmen t with your house exhaust duct after the

oven is installed.

MOUNT THE OVEN

FOR E_IER INSTALIz_-TION AND PERSONAL

SAFE'I'_ V_ RECOMMEND THAT TWO PEOPLE

INSTALL THIS OVEN.

IMPORTANT: Do not grip or use handle

during installation.

NOTE: If yore" cabinet is metal, use the n) ion

grommet around the power cord hole 1o prevent

cutting of Ihe cord,

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf

IMPORTANT: If filler blocks are not

used, case damage may occur from over

tightening scwews.

NOTE: When mounting the

oven, thread power cord

through hole in bottom

of top c_,/binet, Keep it tight

throughout Steps 1-_L

Do not pinch cord or lift

oven by p_flling cord,

_Liff tilt itoven,

forward, and hook

slo_ at back bottom

edge onto two lower

tabs of mounting

plam.

]Rotate front of

oven

up against cabinet

bottom.

_ Insert a self-aligning screw Ihrough top center

cabinet hole, "I_mporarily secure the oven by

turning the screw at least two full mrus after the

thrmuls have engaged. {It MII be completely

tightened iatm;) Be sure to keep power cord tight.

Be careful not to pinch the cord, especially when

mounting flush to bottom of cabinet.

Installation Instructions

MOUNT THE OVEN (continued)

@bineJ:Front

:'Z C_;bineJ:BottomShelf

Iia_A FillerBlock

. T' i.alo,,"o

/K'F//BI!II /IIJI/0%,,0,

--Ove_l Top

I:_"-t'_:htI,eoventothetopca_>h_et,

r l

j 5 jInsert 2 sel_:Migning screws

through outer top cabinet

holes, Turn two rid] turns on

each screw;

[]Tighten cenmr

screw completely,

[] Tighmn the outm: two screws to the top of the

oven, (While tightening screws, hold the oven in

place against the wall and the top cabinet,)

[] Insudl grease tilmrs, See the Owner's Manual

packed with the oven,

[-_ ADJUST THE EXHAUST

ADAPTOR

()pen the topcM)inet and a_itiust the exhaust adaptor

to connect to I]_ehouse duct,

D_mper

Back_f

Ove_

[-_ CONNECTING DUCTWORK

House DUC[

_ Exmnd the house duct down to connect to

the exhaust adaptor;

[] Stud exhaust duct joints using duct tape,

Installation Instructions

OUTSIDE BACK EXHAUST (Horizontal Duct)

INSTALLATION OVERVIEW

B1, Prepare Rear Wall

B2, Attach Mounting Hate m Wail

B3, Prepare "Fop Cabinet

B4, Adjust Blower

B5, Motmt the Oven

PREPARING THE REAR WALL

FOR OUTSIDE BACK EXHAUST

You need to cttt an opening in the rear wall [br

outside exhaust.

• Read the instructions on the REAR WALL

TEMPI_TE,

• Tape it m the rear" _all, lining ap wi(h the holes

previously drilled tot holesA and B in the wall

plate,

• Cut the opening, [bllowing the instrnctions of the

REAR W_\LL TEMPI_\TE,

ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate m the wall using toggle bolts, At least

one wood screw mnst be used to attach (he plate to

a _all stud,

[] Remove the toggle wings from the bolts.

[] Insert the bolts into the mounting plate through

the holes designated m go into dlwwalI and reattaeh

the toggle win_ to g*'_ onto each bolt,

Installation Instructions

To use toggle bolts:

Spacingfer Tu!NlesMore

_ ThanWaftThickness

ITe_lsw,n_s

M_um:ing i 7 I"

• ', 0!N e ,

'a e41.'l,.Zgo,II I:1-,

" I't

II U I

golt End

[] Place dm mounting plato _ainst the wall and

insert the toggle wings into the holes in the wall

to mount the plate,

NOTE: getbre tightening toggle bolts and wood

screw; make sure the tabs on the mounting pla_

touch (he bottom of"the cabinet when pushed flush

against the wall and that the plate is properly

centered trader the cabinet,

CAUTION: Be caref'uI to avoid pinching fingers

between the back of' the moun ling plate and dm wall,

[] Tighten all bolts, Pull the plate awW from the wall

to help tighten the bolts,

USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes fbr the top support screws and

a hole lm:ge enough fbr the power cord to fit through,

• Read tim instructions on the TOP CABINET

"rI?]MPIz\TE.

• Tape it underneath (he mp cabinet.

• Drill the hoIes, fbllowing the instructions on the

TOP CABINET "rI?;MPI J\TE.

CAUTION: WEar safe g goggles when drilling holes

in the cabinet bottom,

F-_ ADAPTING BLOWER FOR

OUTSIDE BACK EXHAUST

[] Remove the three scr_wcs that hold the blower

plate to (he oven. Slide blower plate from trader

its retaining flange. Remove and save (he screw

that holds Mower motor to oven.

glower Rate

_ (]areftfily tim blower unit. The wirespuI1

out

will extend Jar enough to allow you to adjust

the blower unit,

EndB

_ Rotate blower unit counterclockwise 180%

Be[oreRototion After Rototion

Oven

gockof

Oven

[] (_ntly remove the wires fi:om the

grooves,

Reroute the wires through grooves on other side

of"the blower unit,

Be[oreRerouting Aher Reroudng

Installation Instructions

[]Roll the blower trait 90 ° so that ffan blade

openings are f_acing out the back of' the oven,

8ockef 8ockef

[] Locam the two "knockout" plains, on the rear

oven pm_el, near the top of the oven.

Using tin snips, carefully cut the web area f}'om

the two holes side-by-side (I;hat sectlre 1he

knockouts to the oven). Ct_t all fbtlr webs on bolh

rear knockouts; Lhis will M]ow the yen tilation fian

_dr flow to exhat_st ot_t the rear of' Lhe oven.

CAUTION: Be sure to trim the sharp edges from

the openings af*er removing the knockout plates.

Oven Rear Panel

Snipall 4webs

_neachk_ockeul:

g_el o_dremove

t]_emetal knock_u[s

f_rre_ra_rflo_,',,_

[] Place the blower unit back into the opening.

CAUTION: Do not pull or stretch the blower

unit wiring. Make sure the wires are not pinched.

NOTE: The blower unit exhaust openings should

match exhaust openings on rear of oven.

[] Replace the blower plate in the same position

as befi)re with the screws.

BlowerPlo[eScrews

_ 8lowerPlate

[] Insert the tabs on each side of' the dt_per into

the holes at the inside rear of (he adapto_;

Adep[or

_ Attach the exhat_st adaptor to Lhe rear of the

oven b> sliding it into the gtlides at the top

cenmr of' the back of the oven.

E×houstAdeptor

Slideexhaust

adaptorinto

guides0n

ovenfear

_.._ Damper

(hhlgesideup)

dF .

"V'Scre''s

Tabs Guides

Pt_sh in sec_rely until it is in the lower locking

tabs. Take care to t_ss_re the damper hinge is

installed so that it is at fhe mp and Lhat the

damper swings ffreeI};

_ Secure the exhaust adaptor m the oven wiLh the

two bronze meted screws provided.

Installation Instructions

MOUNT THE OVEN

FOR FgkSIER INSTIM,I_\TION AND PERSONAL

St_'_TIS_ V_ RECOMMEND THAT TWO PEOPLE

INSTALL THIS OVEN.

IMPORTANT: Do not grip or use handle

during installation.

NOTE: Ifyonr cabinet is metal, use the nylon

grommet arotmd the power cord hole m prevent

ct*tdng of the cord.

NOTE: D¢_recommend using t_ller Mocks if the

cabinet ti'ont han_ below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not

used, case damage may occur from over

tightening screws.

NOTE: When moundng

film oven, thread power

cord through imle in

bottom of top c_4binet.

_ep it tight throughot_t

Steps I-3. Do not pinch

cord or lit_ oven by

p_flling cord.

[_ Lit:t oven, dlt it

fbrwm'd, m_d hook

slots at back bottom

edge onto two lower

tabs of' mounting plate.

[_ Rotate tYont of oven up

against ct-fbinet bottom.

[] Insert a self:tdigning screw through top center

c_/binet hole. Temporarily secure the oven b)

turning _he screw at least two fMI turns afl.er the

threads have engaged. (It will be completely

tightened late*:.) Be sure to keep power cord tight.

Be carefxd not to pinch the cord, especially when

mounting flush to bottom of cabinet.

0ve_Top

[_Attach the oven to the top cabinet.

[] Insert 2 self:_digning screws

through ot_ter top cabinet

holes, Tm'n two titll turns on

each screw;

iiiiiiiii!

[]Tighten cenmr

screw completely.

[] Tighmn the oater two screws to the top of the

oven. (While tightening screws, hold the oven

in place against the wall and the top cabinet.)

[] Insudl grease filmrs. See the Owner's Manual

packed with the oven.

Installation Instructions

RECIRCULATING {Non-Vented Ductless)

INSTALLATION OVERVIEW

C1. At:ach Mounting Plate to Wall

C2. Prepare Top Cabinet

C3. Adjust Blower

CA. Mount the Oven

C5. Insudl Charcoal Filter

[_ ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate m the wtdl using toggle bolts. At

least one wood screw must be used to attach the

plate to a wall stud.

[]Remove the toggle win_ Dora the bolts.

[nsert the bolts into the nlountin ' la_ throu 'h

[] gP g

the holes designated to go into d*)wldl and

reattach the toggle wings m _A_'onto each bolt.

To use toggle bolts:

SpacflLaforTuggles

MoreThanW_fll

4_Thickness

%ggleWin£s

Mounting i -/Toggl'e

m t,qr_Wall , P i

BollEnd

[] Place 1he mounting plate against the wall m_d

insert the toggle wings into (he holes in the wall

to mount the plate.

NOTE: Betbre tightening toggle bolls and wood

screw, make sure 1he tabs on the mounting plato

much the bottom of the cabinet when pushed flush

agtdnst the wall and that the plate is properly

centered under the cabinet.

CAL_TION: Be carefuI to avoid pinching fingers

between the back of' the mortaring plate and the wtdL

[] Tighten all bolts. Pull the plate away ti:om (he w_dl

to help tighten the boils.

USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

_,_u need to drill holes [br the top support screws and

a hole large enough fbr the power cord to fit (hrough.

_=========_

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the mp cabinet.

• Drill ttm holes, tbllo_ng the instructions on the

TOP CABINET "rEMPIJ\TE.

CAIYrION: Wear safer) goggles when drilling holes

in the c_-ff_inetbottom.

Installation Instructions

ADAPTING BLOWER

FOR RECIRCULATION

NOTE: The exhaust t_laptor with dmnper is not

needed tor recircularSng models, You may want to

save (hem _br possible t'umre use,

[]Remove and save screws that hold blower plum to

(}le oven,

_ _ 8lowerPlateScrews

I i .....

2 j Shde (he blower plum from under its relammg

flange and I ti it off; Remove and save screw fihat

holds the blower motor to oven,

_j glowerRate

I : _ Screw

_1 Carefullv ptfll out the blower unit. The wires

' will exm]_d tar enough m allow you to a([iust the

blower unit.

_i Roll the blower unit 90 ° so that tan bl;_le openin_

Jare fiming toward the &ont of the oven.

R011

NOTE: Make sure wires remain toured in the

grooves of the motor fi'ame,

Page is loading ...

Kenmore Elite JVM1490WH02 Installation guide

Brand: Kenmore Elite

Model: JVM1490WH02

Type: Installation guide

This manual is also suitable for

Download PDF

report

in other languages

español: Kenmore Elite JVM1490WH02 Guía de instalación

Kenmore Elite JVM1490WH02 Installation guide

This manual is also suitable for

Kenmore Elite JVM1490WH02 Installation guide

in other languages

Related papers

Other documents