GE 36363673200 Installation guide

Type
Installation guide

This manual is also suitable for

Installation
Instructions
Abovethe
CooktopOven
JVM1490,SCA1000andSCA1001
I Questions? Carl 800-GE-CARES (800-432-2737) orvisit ore"Websit_ at: www.GEAppliances.com I
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT - Savethese
instructions for local inspector's use.
IMPORTANT - Obsc_-_oall
governing codes and ordinances.
Note to Installer _ Besure to leavethese
instructions with the Consumer.
Note to Consumer - Keep these
instructions for future reference.
Skill level - Installation of this appliance requires
basic mechanical and electrical skills.
Proper installation is the responsibility of the installm:
Product failure due to improper installation is not
covered under the Warranty.
I!! Ii
LA SECCION EN ESPAI_IOL
EMPIEZA EN LA PAGINA 25.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Instructions
CONTENTS
General information
Important Safety Instructions .................................. 3
Electrical Requirements .......................................... 3
Hood Exhaust ...................................................... 4, 5
Damage - Shipment/Installation .............................. 6
Parts Included .......................................................... 6
Tools You Will Need ................................................ 7
Mounting Space ...................................................... 7
Step-by-step installation guide
Placement of Mounting Plate ............................ 8-10
Rcmox_mg the Mounting Plate ...................... 8
Finding tile Wall Studs .................................. 8
Determining Wall Plate Location .................. 9
Aligning the Wall Plate ................................ 10
Installation Types .............................................. 11-22
_] Outside Top ............................
Exhaust
12-14
Attach Mounting Plate to Wall ............ 12
Preparation of Top Cabinet ................ 13
Checking for Proper Damper
Operation ............................................ 13
Mount the Oven ............................ 13, 14
Adjust the Exhaust Adaptor ................ 14
Connecting Ductwork .......................... 14
_] Outside Back Exhaust 15-18
Preparing Rear Wall for
Outside Back Exhaust .......................... 15
Attach Mounting Plate to Wall ...... 15, 16
Preparation of Top Cabinet ................ 16
Adapting Blower for Outside
Back Exhaust .................................... 16, 17
Mount the Oven .................................. 18
] Recirculating ........................................ 19-22
Attach Mounting Plate to Wall ............ 19
Preparation of Top Cabinet ................ 19
Adapting Blower
for Recirculation .......................... 20, 21
Mount the Oven ............................ 21, 22
Installing the Charcoal Filter .............. 22
Before You Use Your Oven .................................. 23
Secci6n en Espafiol ........................................ 2547
2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
This product requires a three-prong grounded
outlet. The installer must peribrm a ground continuity
check on the power outlet box beibre beginning the
installation m insure that tile outlet box is properly
grounded, if not properly grounded, or if the
outlet box does not meet electrical requirements
noted (under ELECTRICAL REQUIREMENTS),
a qualified electrician should be employed to
correct any deficiencies.
CAUTION: For personal
safety, remove house fuse
or open circuit breaker
before beginning installation
to avoid severe or fatal
shock injury.
CAUTION: For personal safety, the momaling surface
must be capable of supporting the cabinet load, ha
addition to the added weight of this 63-85 pound
product, plus additional oven loads of up to 50 pounds
or a total weight of 113-135 pounds.
CAUTION: For personal safety, this product cannot
be installed ha cabinet arrangements such as an island or
a peninsula. It must be mounted to BOTH a top cabinet
AND a wall.
NOTE: For easier installation and personal safety, it is
recommended that two people install this product.
IMPORTANT--PLEASE READ CARF_UIIY. FOR
PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED TO AVOID SEVERE OR
FATAL SHOCK.
The power cord of this appliance is equipped with
a three-prong (grounding)
plug which mates with
a standard three-prong
(grounding) wall receptacle
to minimize the possibility
of electric shock hazard
from this appliance.
insureproper
groundexists
beforeuse
You should have the wall receptacle and circuit checked
by a qualified electricima to make sure the receptacle is
properly grounded.
Where a standard two-prong wall receptacle is
encomatered, it is very important to have it replaced
with a properly grounded three-prong wall receptacle,
installed by a qualified electrician.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT,
DEFORM, OR REMOVE ANY OF THE PRONGS
FROM THE POWER CORD. DO NOT USE WITH
AN EXTENSION CORD.
ELECTRICAL
REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz, 15 amps, and
1.70 kilowatts. This product must be connected to
a supply circuit of the proper voltage and fi'equency.
Wire size must conform to the requirements of the
National Electrical Code or the prevailing local code
for this kilowatt rating. The power supply cord and
plug should be brought to a separate 15 to 20 ampere
branch circuit single grounded outlet. The outlet box
should be located in the cabinet above the oven. The
outlet box and supply circuit should be installed by
a qualified electrician and conform to the National
Electrical Code or the prevailing local code.
3
Installation Instructions
HOOD EXHAUST
NOTE: Read these next two pages only if you plan to vent your exhaust to the outside.
If you plan to recirculate the air back into the room, proceed to page 6.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The fbllowing chart describes an example of one possible
ductwork installation.
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH x USED = LENGTH
RoofCap 24 Ft. x (1) = 24 Ft.
12Ft.StraightDuct 12Ft. x (1) = 12Ft.
(6" Round)
Rectangular4o-Round 5Ft. x (1) = 5Ft.
TransitionAdaptor*
Equivalentlengthsofductpiecesarebasedonactualtestsand
reflectrequirementsfor goodventingperformancewith anyventhood.
Total Length = 41 Ft.
*IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper
will have to be cut to fit, using the tin snips, in order to allow fi'ee movement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible
ductwork installation.
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH* x USED = LENGTH
_,.....__ WallCap 40Ft. x (1) 40Ft.
3 Ft.StraightDuct 3 Ft. x (1) 3 Ft.
37g"x 10"Rectangular)
90° Elbow 10Ft. x (2) 20Ft.
Equivalentlengthsof ductpiecesarebasedonactualtests and
reflectrequirementsforgoodventingperformancewith anyvent hood.
Total Length = 63 Ft,
NOTE: For back exbaust, care sbould be taken to align exhaust witb space between studs, or wall should be prepared
at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.
4
Installation Instructions
NOTE: If you need to install ducts, note that the total
duct lengtb of 3¼" x 10" rectangular or 6" diameter
round duct should not exceed 140 equivalent feet.
Outside ventilation requires a HOOD EXHAUST DUCT.
Read tile following carefully.
NOTE: It is important tbat venting be installed using
the most direct route and with as few elbows as possible.
This ensures clear venting of exhaust and helps prevent
blockages. Also, make sure dampers swing freely and
nothing is blocking the ducts.
Exhaust connection:
The hood exhaust has been designed to mate witb
a standard 3¼" x 10" rectangular duct.
If a round duct is required, a rectangular-to-round
transition adaptor must be used. Do not use less than
a 6" diameter duct.
Maximum duct length:
For satisfhctory air movement, the total duct length of"
3¼" x 10" rectangular or 6" diameter round duct should
not exceed 140 equivalent feet.
Elbows, transitions, wall and roof caps, etc.,
present additional resistance to airflow and are equivalent
to a section of straight duct which is longer than their
actual physical size. When calculating the total duct
lengtb, add tbe equivalent lengtbs of all transitions and
adaptors plus tbe length of all straight duct sections.
The chart below shows you how to calculate total
equivalent ductwork length using the approximate feet
of equivalent lengtb of some typical ducts.
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH x USED = LENGTH
Rectangular_to-Round 5 Ft. x ( ) Ft.
TransitionAdaptor*
Wall Cap 40 Ft. x ( ) Ft.
(i)_ 9O°EIbow lOFt. x ( ) Ft.
(_ 45° Elbow 5 Ft. x ( ) Ft.
90° Elbow 25 Ft. x ( ) Ft.
45° Elbow 5 Ft. x ( ) Ft.
RoofCap 24 Ft. x ( ) Ft.
StraightDuct6" Roundor 1 Ft. x ( ) Ft.
3¼" x 10"Rectangular
Total Ductwork = Ft.
* IMPORTANT: if a iectangtflm_to-round transition Equiwflent lengths of duct pieces are based on actual tests and
adaptor is used, the bottom cornm_ of the damper reflect requirements for good venting performance with any
_'iU ha_e to be cut to fit, t_sing the tin snips, in _ent hood.
order to aUo_ fi'ee inovement of the damper.
5
Installation Instructions
DAMAGE - SHIPMENT/
INSTALLATION
" If the unit is damaged in shipment, return tile
unit m the store in which it was bought J[br repair
or replacement.
" If the unit is damaged by the customer, repair or
replacement is the responsibility of the customer.
" If the unit is damaged by the installer (if other
than the customer), repair or replacement must
be made by arrangement between customer and
installmz
PARTS INCLUDED
HARDWARE PACKET
PART QUANTITY
WoodScrews 2
(I/4_1 X 2")
I\ Togg{eBolts(and 4
_ wingnuts)(_A"x3")
Se{f-a{igningMachine 3
Screws(IA"_28x 3_A")
NylonGrommet 2
(formetalcabinets)
ExhaustAdaptor 1
_ Damper 1
Metal Screws 1black
(IA"x *A") 2bronze
PowerCordStrap 1
(plastic)
You will find the installation hardware contained in
a packet with the unit. Check to make sure you have
all these parts.
NOTE: Some extra parts are included.
PARTS INCLUDED
ADDITIONAL PARTS
PART
_ _msEr w
L
®
TopCabinet
Template
RearWall
Template
Installation
Instructions
Sepamtely
Packed
Grease
Filters
QUANTITY
1
6
Installation Instructions
TOOLS YOU WILL NEED
# I o_d#2 Phifiipsscrewdriver
Pencil
Ruleror 1:apemeasure
figh[ edge
{ep[i_nal)
_n snips {fer [:u[[ill[_
Gloves
Sofe_goggles
_cissers
Electricdrillwi[h :_(", _i(',
_" a_d_" driftbi[s Fillerblocks_r scrap
weedpieces,ifileeded
fer [epcabine[spacfl_g
(usedonrecessedbottom
cebfl_etfl_stallotiensonly)
Studffl_der or
@
Ductandmaskingtape
Level
MOUNTING SPACE
plosh
NOTES:
" _I_e space between dm cabinets must be NY" wide
m_d tYee of' obstructions.
" If the space between the cabinets is greater
than BO", a Filler Panel Kit may be used to fill
in ti_e g_ap between lhe oven and the cabinets.
}%ar (_cr's ManuN contains the kit number
tbr your model.
This oven is tbr installation over ranges tip m
36" wide,
" If you are going m vent your oven m lhe outside,
see Hood Exhaust Section tbr exhaust duct
preparation.
When installing the oven beneath smooth, flat
cabinets, be care[_l to follow the instruc_ons
on the top cabinet template For power cord
clearance.
7
Installation Instructions
PLACEMENT OF THE MOUNTING PLATE
[] REMOVING THE OVEN FROM
THE CARTON/REMOVING THE
MOUNTING PLATE
[]Remove the box conudning the instMlation
instructions, filters, exhaust adaptm; damper
and the small hardware bag. Do not remove
the Styrofbam protecting the fl:ont of the oven,
[] Fold back all 4 carton flaps fully against c_u'ton
sides. Then carefully roll 0_e oven and era:ton over
onto the top side. The oven should be resting in
the Styrofbam.
[] Pull Ihe car_on up and off the oven.
[] The motmting plate is attached to the back of the
oven. Remove the two screws holding it to the oven,
The plate will be used as the rear wall template and
fbr mounting the oven to the wall.
[] Set the oven upright. Remove and properly discard
plastic bags and Styrofbwn.
[] Open the oven door and remove 1he st}rotbarn
pack Dora inside the oven. Remove Ihe tape
covering the tumlable hub,
[-_ FINDING THE WALL STUDS
[] Find the studs, using one of the fbllowing
methods:
A. Stud finder - a magnetic device which
locates nails.
OR
B T
• Use a hmnmer to tap lightly across the
mounting surfhce to find a solid sound,
This will indicate a stud location,
[] After locating Ihe stud(s), tind the center by
probing Ihe v#all with a sm_dl nail to find the
edges of the stud, Then place a mark halgva)
between the edges. The center of any _ljacent
studs should be 16_"or- 24" fi'om Ibis mark,
]Draw a line down the center of the studs,
THE OVEN MUST BE CONNECTED TO AT LEAST
ONE WALL STUD•
8
Installation Instructions
[] DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position - beneath flat bottom
cabinet
Plate position - beneath framed recessed
cabinet bottom
Maunth_gPI_teTabs
Moum:ingPlateTabs
Teuchi_gthe Back
Frame
Plate position - beneath recessed bottom
cabinet with front overhang
II
30" to Cooktap
S%ur cabinets may have decorative trim that intertcres
with d_e oven inst_dlation. Remove the decorative n'im
to install the oven properI_ and to make it level.
THE OVEN MUST BE LEVEL.
Use a l_'eI to make sure the cabinet bottom is level.
If' the cabinets have a lyon t overhang only, Mth no
back or side &ame, install the moundng plate down
the same distance as the &ont ore€hang depth. This
will keep the oven level.
[] Measure the inside depth of the fl'ont overhang.
[] Draw a horizontal line on Ihe t_ck _vall
eqt_]
all
distal_ce below the c_binet bottom ;_ the inside
depth of the fi'ont ove_:hal_g.
[] For I}fis t}_e of inst_dlation with front
overhal]g onl}_
align Ihe moundng u4bs with Ih:is horizonud line, not
touching the cabinet tx_ttom as descrit_d in Step D.
9
Installation Instructions
[] ALIGNING THE WALL PLATE
HoleC _ 0 0 0 0 b 0000000000
0 0 0 O 0 OI 0000O 000
CAUTION: Wear gloves
to avoid cutdng fingers on
sharp edges,
I
Area E
HoleD
Draw a ve*_ictd line on the wall at (he center of the
[]
3(Y' wide space.
[] Use (he mounting plate as the template [br (he rear
wtdl. Place the mortaring plato on the wall, making
sttre lhat the tabs are touching the bottom o1' the
cabinet or the level llne dl_awn in Step C [or cabinets
with [font overhang. Line up the notch and center line
on the monnting plate to the center line on the wall.
[] Dc]ai[e holding (he mounting plate with one hand,
draw circles on (he wall tat holes A, B, C and D (see
illustration aboveiactuM plate marked with an:ows).
Fore* holes mttst be used for mounting,
[]
NOTE: Holes C and D are inside area E. ff neilher
C nor D is in a stud, find a stud som_here in area E
and draw a fifth circle to Iine up M(I_ (he stud. It is
imporlant to tt_ at least one wood screw mortared
firmly in a stud to support the weight of the oven.
Set the mounting plate aside.
Drill holes on 1he circles. K there is a stud, drill a _a"
hole tbr wood screws. For holes that don't line up wifl_
a stud, drill a %" hale tbr toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
10
Installation Instructions
INSTALLATION TYPES (Choose A, B or C}
This oven is designed fbr adaptation to the fbllowing
3 t}pes of ventilation:
A_Outside Top ExhatJst (Vertical Duct)
Outside Back Exhaust (Horizontal Duct)
C. Recirculatmg (Non-Vented Ductless)
NOTE: This oven is shipped assembled fbr Outside Top
Exhaust, Select 1he t)pe ofventiIadon required fbr your
installation and proceed to that section,
OUTSIDE TOP EXHAUST
(VERTICAL DUCT}
OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT}
RECIRCULATING
(NON-VENTED DUCTLESS}
A Charco;d Filter i_cessory
Kit is required tor the
non-vented exhaust, (See your
(_er's ManuN fbr the kit
numbe_:)
11
Installation Instructions
OUTSIDE TOP EXHAUST (Vertical Duct)
INSTALLATION OVERVIEW
AI÷ Attach Mounting Plate m Wal]
A2. Prepare "Fop Cabinet
A3. Install sL_apter
A4. Moant Oven
A_. Adjust Exhat_st Adaptor
A6. Connect Ductwork
m
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wtdl rising toggle bolts,
At least one wood screw most be osed to attach the
p]ate to a wall stud,
[] Remove the toggle win_ ti'om the bolts.
[] Insert the bolts into the mounting plate through
the holes designated to go into dD_dl and
reattach tile toggle wings to %_"onto e_ch bolt.
To use toggle bolts:
Sp_cin__orIo,agles
MoreThanWoll
_l,,,_Thickn ess
Iro_leWin_s
Mou_tin_ IIl, lJ /To!NI'_ II II
BoltEnd
[] Place the mounting plate against the wall m_d
insert the toggle wings into the holes in the wal]
to mount the plate.
NOTE: Befbre tightening toggle bolts and wood
screw, make sure the tabs on the mounting plato
touch the bottom of the cabinet when pushed
flush against (he wMl and (hat the plato is properly
centered trader the cabinet,
CALrTION: Be carefuI to avoid pinching fingers
between the back of' the moondng plate and the wM1.
_ Tighten all bolts. Pull the p]ate away fi'om the wM1
to help tighten the bolts,
12
Installation Instructions
[-_ USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes fbr the top support screws,
a hole large enough fbr 1he power cord to fit through,
and a cutout large enough fbr the exhaust adaptor:,
Read the instructions on the TOP CABINET
TEMPIJVFF.
Tape it underneath the top c_4binet.
Drill the holes, fblloMng the instructions on the
TOP CABINET TEMPIATE.
CAUTION: Wear s_4"et}goggles When dfilEng holes
in the cabinet bottom.
[-_ ASSEMBLE AND
INSTALL ADAPTOR
[_ Place the oven in its upright position, with the top
of the unit tacing up.
[] Insert 0_e tabs on each side of 0_e damper into the
holes at the inside *:ear:of the adaptor.
_ Attach the exhaust adaptor to the blower plate with
the two bronze metal screws provided.
Make salre that the damper pivots easily before
mounting oven.
_'_u wit1 need to make adjusmaents to asstu'e proper
_dignmen t with your house exhaust duct after the
oven is installed.
MOUNT THE OVEN
FOR E_IER INSTALIz_-TION AND PERSONAL
SAFE'I'_ V_ RECOMMEND THAT TWO PEOPLE
INSTALL THIS OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE: If yore" cabinet is metal, use the n) ion
grommet around the power cord hole 1o prevent
cutting of Ihe cord,
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf
IMPORTANT: If filler blocks are not
used, case damage may occur from over
tightening scwews.
NOTE: When mounting the
oven, thread power cord
through hole in bottom
of top c_,/binet, Keep it tight
throughout Steps 1-_L
Do not pinch cord or lift
oven by p_flling cord,
_Liff tilt itoven,
forward, and hook
slo_ at back bottom
edge onto two lower
tabs of mounting
plam.
\
]Rotate front of
oven
up against cabinet
bottom.
_ Insert a self-aligning screw Ihrough top center
cabinet hole, "I_mporarily secure the oven by
turning the screw at least two full mrus after the
thrmuls have engaged. {It MII be completely
tightened iatm;) Be sure to keep power cord tight.
Be careful not to pinch the cord, especially when
mounting flush to bottom of cabinet.
13
Installation Instructions
MOUNT THE OVEN (continued)
@bineJ:Front
:'Z C_;bineJ:BottomShelf
Iia_A FillerBlock
. T' i.alo,,"o
/K'F//BI!II /IIJI/0%,,0,
--Ove_l Top
I:_"-t'_:htI,eoventothetopca_>h_et,
r l
j 5 jInsert 2 sel_:Migning screws
through outer top cabinet
holes, Turn two rid] turns on
each screw;
[]Tighten cenmr
screw completely,
[] Tighmn the outm: two screws to the top of the
oven, (While tightening screws, hold the oven in
place against the wall and the top cabinet,)
[] Insudl grease tilmrs, See the Owner's Manual
packed with the oven,
[-_ ADJUST THE EXHAUST
ADAPTOR
()pen the topcM)inet and a_itiust the exhaust adaptor
to connect to I]_ehouse duct,
D_mper
#
Back_f
Ove_
[-_ CONNECTING DUCTWORK
House DUC[
_ Exmnd the house duct down to connect to
the exhaust adaptor;
[] Stud exhaust duct joints using duct tape,
14
Installation Instructions
OUTSIDE BACK EXHAUST (Horizontal Duct)
INSTALLATION OVERVIEW
B1, Prepare Rear Wall
B2, Attach Mounting Hate m Wail
B3, Prepare "Fop Cabinet
B4, Adjust Blower
B5, Motmt the Oven
PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
You need to cttt an opening in the rear wall [br
outside exhaust.
Read the instructions on the REAR WALL
TEMPI_TE,
Tape it m the rear" _all, lining ap wi(h the holes
previously drilled tot holesA and B in the wall
plate,
Cut the opening, [bllowing the instrnctions of the
REAR W_\LL TEMPI_\TE,
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate m the wall using toggle bolts, At least
one wood screw mnst be used to attach (he plate to
a _all stud,
[] Remove the toggle wings from the bolts.
[] Insert the bolts into the mounting plate through
the holes designated m go into dlwwalI and reattaeh
the toggle win_ to g*'_ onto each bolt,
15
Installation Instructions
To use toggle bolts:
Spacingfer Tu!NlesMore
_ ThanWaftThickness
ITe_lsw,n_s
M_um:ing i 7 I"
', 0!N e ,
'a e41.'l,.Zgo,II I:1-,
" I't
II U I
golt End
[] Place dm mounting plato _ainst the wall and
insert the toggle wings into the holes in the wall
to mount the plate,
NOTE: getbre tightening toggle bolts and wood
screw; make sure the tabs on the mounting pla_
touch (he bottom of"the cabinet when pushed flush
against the wall and that the plate is properly
centered trader the cabinet,
CAUTION: Be caref'uI to avoid pinching fingers
between the back of' the moun ling plate and dm wall,
[] Tighten all bolts, Pull the plate awW from the wall
to help tighten the bolts,
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes fbr the top support screws and
a hole lm:ge enough fbr the power cord to fit through,
%
%
Read tim instructions on the TOP CABINET
"rI?]MPIz\TE.
Tape it underneath (he mp cabinet.
Drill the hoIes, fbllowing the instructions on the
TOP CABINET "rI?;MPI J\TE.
CAUTION: WEar safe g goggles when drilling holes
in the cabinet bottom,
F-_ ADAPTING BLOWER FOR
OUTSIDE BACK EXHAUST
[] Remove the three scr_wcs that hold the blower
plate to (he oven. Slide blower plate from trader
its retaining flange. Remove and save (he screw
that holds Mower motor to oven.
glower Rate
_ (]areftfily tim blower unit. The wirespuI1
out
will extend Jar enough to allow you to adjust
the blower unit,
EndB
_ Rotate blower unit counterclockwise 180%
Be[oreRototion After Rototion
Oven
gockof
Oven
[] (_ntly remove the wires fi:om the
grooves,
Reroute the wires through grooves on other side
of"the blower unit,
Be[oreRerouting Aher Reroudng
16
Installation Instructions
[]Roll the blower trait 90 ° so that ffan blade
openings are f_acing out the back of' the oven,
8ockef 8ockef
[] Locam the two "knockout" plains, on the rear
oven pm_el, near the top of the oven.
Using tin snips, carefully cut the web area f}'om
the two holes side-by-side (I;hat sectlre 1he
knockouts to the oven). Ct_t all fbtlr webs on bolh
rear knockouts; Lhis will M]ow the yen tilation fian
_dr flow to exhat_st ot_t the rear of' Lhe oven.
CAUTION: Be sure to trim the sharp edges from
the openings af*er removing the knockout plates.
Oven Rear Panel
Snipall 4webs
_neachk_ockeul:
g_el o_dremove
t]_emetal knock_u[s
f_rre_ra_rflo_,',,_
[] Place the blower unit back into the opening.
CAUTION: Do not pull or stretch the blower
unit wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings should
match exhaust openings on rear of oven.
[] Replace the blower plate in the same position
as befi)re with the screws.
BlowerPlo[eScrews
J
_ 8lowerPlate
[] Insert the tabs on each side of' the dt_per into
the holes at the inside rear of (he adapto_;
Adep[or
_ Attach the exhat_st adaptor to Lhe rear of the
oven b> sliding it into the gtlides at the top
cenmr of' the back of the oven.
E×houstAdeptor
Slideexhaust
adaptorinto
guides0n
ovenfear
_.._ Damper
(hhlgesideup)
dF .
"V'Scre''s
Tabs Guides
Pt_sh in sec_rely until it is in the lower locking
tabs. Take care to t_ss_re the damper hinge is
installed so that it is at fhe mp and Lhat the
damper swings ffreeI};
_ Secure the exhaust adaptor m the oven wiLh the
two bronze meted screws provided.
17
Installation Instructions
MOUNT THE OVEN
FOR FgkSIER INSTIM,I_\TION AND PERSONAL
St_'_TIS_ V_ RECOMMEND THAT TWO PEOPLE
INSTALL THIS OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE: Ifyonr cabinet is metal, use the nylon
grommet arotmd the power cord hole m prevent
ct*tdng of the cord.
NOTE: D¢_recommend using t_ller Mocks if the
cabinet ti'ont han_ below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not
used, case damage may occur from over
tightening screws.
NOTE: When moundng
film oven, thread power
cord through imle in
bottom of top c_4binet.
_ep it tight throughot_t
Steps I-3. Do not pinch
cord or lit_ oven by
p_flling cord.
[_ Lit:t oven, dlt it
fbrwm'd, m_d hook
slots at back bottom
edge onto two lower
tabs of' mounting plate.
[_ Rotate tYont of oven up
against ct-fbinet bottom.
[] Insert a self:tdigning screw through top center
c_/binet hole. Temporarily secure the oven b)
turning _he screw at least two fMI turns afl.er the
threads have engaged. (It will be completely
tightened late*:.) Be sure to keep power cord tight.
Be carefxd not to pinch the cord, especially when
mounting flush to bottom of cabinet.
0ve_Top
[_Attach the oven to the top cabinet.
[] Insert 2 self:_digning screws
through ot_ter top cabinet
holes, Tm'n two titll turns on
each screw;
iiiiiiiii!
[]Tighten cenmr
screw completely.
[] Tighmn the oater two screws to the top of the
oven. (While tightening screws, hold the oven
in place against the wall and the top cabinet.)
[] Insudl grease filmrs. See the Owner's Manual
packed with the oven.
18
Installation Instructions
RECIRCULATING {Non-Vented Ductless)
INSTALLATION OVERVIEW
C1. At:ach Mounting Plate to Wall
C2. Prepare Top Cabinet
C3. Adjust Blower
CA. Mount the Oven
C5. Insudl Charcoal Filter
[_ ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate m the wtdl using toggle bolts. At
least one wood screw must be used to attach the
plate to a wall stud.
[]Remove the toggle win_ Dora the bolts.
[nsert the bolts into the nlountin ' la_ throu 'h
[] gP g
the holes designated to go into d*)wldl and
reattach the toggle wings m _A_'onto each bolt.
To use toggle bolts:
SpacflLaforTuggles
MoreThanW_fll
4_Thickness
%ggleWin£s
Mounting i -/Toggl'e
m t,qr_Wall , P i
BollEnd
[] Place 1he mounting plate against the wall m_d
insert the toggle wings into (he holes in the wall
to mount the plate.
NOTE: Betbre tightening toggle bolls and wood
screw, make sure 1he tabs on the mounting plato
much the bottom of the cabinet when pushed flush
agtdnst the wall and that the plate is properly
centered under the cabinet.
CAL_TION: Be carefuI to avoid pinching fingers
between the back of' the mortaring plate and the wtdL
[] Tighten all bolts. Pull the plate away ti:om (he w_dl
to help tighten the boils.
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
_,_u need to drill holes [br the top support screws and
a hole large enough fbr the power cord to fit (hrough.
_=========_
Read the instructions on the TOP CABINET
TEMPLATE.
Tape it underneath the mp cabinet.
Drill ttm holes, tbllo_ng the instructions on the
TOP CABINET "rEMPIJ\TE.
CAIYrION: Wear safer) goggles when drilling holes
in the c_-ff_inetbottom.
19
Installation Instructions
ADAPTING BLOWER
FOR RECIRCULATION
NOTE: The exhaust t_laptor with dmnper is not
needed tor recircularSng models, You may want to
save (hem _br possible t'umre use,
[]Remove and save screws that hold blower plum to
(}le oven,
_ _ 8lowerPlateScrews
II
I i .....
2 j Shde (he blower plum from under its relammg
flange and I ti it off; Remove and save screw fihat
holds the blower motor to oven,
_j glowerRate
I : _ Screw
_1 Carefullv ptfll out the blower unit. The wires
' will exm]_d tar enough m allow you to a([iust the
blower unit.
_i Roll the blower unit 90 ° so that tan bl;_le openin_
Jare fiming toward the &ont of the oven.
R011
NOTE: Make sure wires remain toured in the
grooves of the motor fi'ame,
2O
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

GE 36363673200 Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages