Moffat CN4 Operating instructions

Brand: Moffat

Model: CN4

Type: Operating instructions

This manual is also suitable for

242351-3

Gas Pasta / Noodle Cooker

Models:

CP4 (Pasta Cooker)

CN4 (Noodle C ooker)

I N S T A L L A T I O N A N D O P E R A T I O N M A N U A L

The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized

previously in writing by the manufacturer.

In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the

specifications and design without prior notice.

Moffat Limited

Rolleston 7675

New Zealand

AUSTRALIA

Moffat Pty Limited

E.Mail: [email protected]m.au

Main Office: (tel): +61 (03) 9518 3888

(fax): +61 (03 9518 3833

Service: (tel): 1800 622 216

Spares: (tel): 1800 337 963

Customer Service: (tel): 1800 335 315

(fax): 1800 350 281

CANADA

Serve Canada

Web: www.servecanada.com

E.Mail: info@servecanada.com

Sales: (tel): 800 551 8795 (Toll Free)

Service: (tel): 800 263 1455 (Toll Free)

NEW ZEALAND

Moffat Limited

Web: www.moffat.co.nz

E.Mail: [email protected]

Main Office: (tel): 0800 663328

UNITED KINGDOM

Blue Seal

Web: www.blue-seal.co.uk

E.Mail: sales@blue-seal.co.uk

Sales: (tel): +44 121 327 5575

(fax): +44 121 327 9711

Spares: (tel): +44 121 322 6640

(fax): +44 121 327 9201

Service: (tel): +44 121 322 6644

(fax): +44 121 327 6257

UNITED STATES

Moffat

Web: www.moffat.com

Sales: (tel): 1-800 551 8795 (Toll Free)

(tel): 336 661 1556

(fax): 336 661 9546

Service: (tel): 866 673 7937 (Toll Free)

REST OF WORLD

Moffat Limited

Web: www.moffat.co.nz

E.Mail: [email protected].nz

CP4 GAS PASTA COOKER - (Single Tank - 40 Ltr).

CN4 GAS NOODLE COOKER - (Single Tank - 40 Ltr).

Model Numbers Covered in this Specification

General

Gas Connection

Gas Supply Requirements

Water Supply Requirements

Installation Requirements

Unpacking

Location

Clearances

Assembly

Gas Connection

Water Connection

Drainage Connection

Commissioning

Operation Guide

Description of Controls

Before Use

Filling the Tank

Lighting the Pilot Burner

Lighting the Main Burner

Turning ‘OFF’ the Pasta / Noodle Cooker

General

Draining and Cleaning

Daily Cleaning

Weekly Cleaning

Periodic Maintenance

Gas Conversion Procedure

Gas Specifications

We are confident that you will be delighted with your COBRA Pasta / Noodle Cooker and it will become a

most valued appliance in your commercial kitchen.

To ensure you receive the utmost benefit from your new COBRA appliance, there are two important things

you can do.

Please read the instruction book carefully and follow directions given. The time taken will be well spent.

If you are unsure of any aspect of the installation, instructions or performance of your appliance,

contact your COBRA dealer promptly. In many cases a phone call could answer your question.

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH.

READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS

APPLIANCE.

INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE USER SMELLS GAS ARE TO BE POSTED IN A PROMINENT LOCATION. THIS INFORMATION

SHALL BE OBTAINED BY CONSULTING THE LOCAL GAS SUPPLIER.

GREAT CARE MUST BE TAKEN BY THE OPERATOR TO USE THE EQUIPMENT SAFELY TO GUARD IT AGAINST RISK OF FIRE.

 THE APPLIANCE MUST NOT BE LEFT ‘ON’, UNATTENDED.

 IT IS RECOMMENDED THAT A REGULAR INSPECTION IS MADE BY A COMPETENT SERVICEMAN TO ENSURE CORRECT AND SAFE

OPERATION OF YOUR APPLIANCE IS MAINTAINED.

 DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER

APPLIANCE.

 DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

Model Covered in this Specification -

CP4 GAS PASTA COOKER (Single Tank - 40 Ltr).

CN4 GAS NOODLE COOKER (Single Tank - 40 Ltr).

A commercial heavy duty, gas fired high

performance Pasta / Noodle Cooker designed for

cooking commercial high production output, using

LPG (Propane), Natural Gas or Butane. The boiling

medium is contained within a heavy gauge stainless

steel tank, heated by one infra red surface burner

from beneath the tank.

This Pasta / Noodle Cooker features an Over

Temperature Safety Cut Out System with Full Flame

Failure Safety Controls.

An open tank design to make cleaning a simple

and easy task.

Gas supply connection point is located 152mm from

the left hand side, 33mm from the rear and 140mm

from the floor.

Gas Connection is

” BSP male.

- Flexible Hose Connection

If a Gas Hose assembly is used to connect this

appliance, the hose and all fittings must have a

minimum ¾” (Natural Gas) or ½” (LPG) inside bore

diameter to ensure gas flow rate capacity

required by this appliance is achieved.

This must be verified by the operating pressure

testing at the maximum gas supply demand

condition.

The Gas Hose assembly should also be classified

for use in the commercial kitchen conditions, the

appliance will be used in.

Recommended Gas Hose Assembly Specification:

- AS/NZS 1869 Class B or D compliant or equivalent,

that meets the following requirements:-

Dimensions:-

Class

Max Working

Pressure

at 23 ± 2ºC

Working

Temperature

Range

Resistance to Oil

7.0 kPa

- 20ºC to + 125ºC

Oil resistant lining

and cover.

2.6 MPa

- Australia:

- New Zealand:

- UK Only:

Category: II

2H3P.

Flue Type: A

- All Other Markets:

NOTE:

 (*) Burner operating pressure is to be measured at Burner Operating Pressure test point on gas

control valve, with burner operating at 'High Flame' setting.

 Operating pressure is ex-factory set and is not to be adjusted, apart from when converting between

gasses, if required.

 Refer to ‘Gas Conversion and Specifications' section in this manual for further details.

A cold water supply must be connected to water inlet connection (R

" BSP), located 50mm from LH

side, 556mm from rear and 135mm from floor. Water connection should be plumbed in, in

accordance with National / Local Codes covering installation.

Maximum water supply pressure 550 kPa (80psi).

Tank max capacity - 40ltrs of water.

Input Rating (N.H.G.C.)

47 MJ/hr 47 MJ/hr 46 MJ/hr

Supply Pressure

2.75 - 4.50 kPa 2.75 - 4.50 kPa 1.13 - 3.40 kPa

Burner Operating Pressure (*)

2.6 kPa 2.6 kPa 0.92 kPa

Gas Connection ¾” BSP Male

Input Rating (N.H.G.C.)

46 MJ/hr 47 MJ/hr

Supply Pressure

1.13 - 3.40 kPa 2.75 - 4.50 kPa

Burner Operating Pressure (*)

0.92 kPa 2.6 kPa

Gas Connection ¾” BSP Male

Nominal Reduced Nominal Reduced

Heat Input (nett) 12.0 kW 5.4 kW 12.5 kW 6.2 kW

Gas Rate 1.27 m

/hr 0.42 m

/hr 0.97 kg/hr 0.48 kg/hr

Supply Pressure

20 mbar 37 mbar

Burner Operating Pressure (*)

9.5 mbar 27.7 mbar

Gas Connection

” BSP Male

Input Rating (N.H.G.C.)

46 MJ/hr 47 MJ/hr

Supply Pressure

1.13 - 3.40 kPa 2.75 - 4.50 kPa

Burner Operating Pressure (*)

0.92 kPa 2.6 kPa

Gas Connection ¾” BSP Male

NOTE:

It is most important that this appliance is installed

correctly and that operation is correct before use.

Installation shall comply with local, gas, health and

safety requirements.

This appliance shall be installed with sufficient

ventilation to prevent the occurrence of

unacceptable concentrations of health harmful

substances in the room, the appliance is installed in.

Cobra Gas Pasta / Noodle Cookers are designed to

provide years of satisfactory service and correct

installation is essential to achieve the best

performance, efficiency and trouble-free operation.

This appliance must be installed in accordance with

National installation codes and in addition, in

accordance with relevant National / Local codes

covering gas and fire safety.

Australia / New Zealand:

AS/NZS 5601- Gas Installations.

United Kingdom: Gas Safety (Installation and

Use) Regulations 1998.

BS6173 - Installation of

Catering Appliances.

BS5440 - Parts 1 & 2 Installation

Flueing & Ventilation.

Ireland: IS 820 - Non Domestic Gas

Installations.

Installations must be carried out by qualified service

persons only. Failure to install equipment to the

relevant codes and manufacturer’s specifications

shown in this section will void the warranty.

Components having adjustments protected (e.g.

paint sealed) by manufacturer, are only to be

adjusted by a qualified service agent. They are not

to be adjusted by the installation person.

 Remove all packaging and transit protection

from the appliance including all protective

plastic coating from the door outer panel and

exterior stainless steel panels.

 For the CN4 Noodle Cooker, remove the

protective coating from the Basket Support

Frame.

 Check the equipment and parts for damage.

Report any damage immediately to the carrier

and distributor.

 Report any deficiencies to the distributor who

supplied the appliance.

 Check that the available gas supply is correct to

that shown on the rating plate located on the

inside of the access door.

 Check that the following parts have been

supplied with the appliance:-

CP4 Pasta Cooker

Baskets LH 165 x 125mm Qty 3.

Baskets RH 165 x 125mm Qty 3.

Basket Support Frame Qty 1.

CN4 Noodle Cooker

Noodle Baskets Qty 5.

Noodle Basket Support Frame Qty 1.

1. This appliance must be installed in a suitably

ventilated room to prevent dangerous build up

of combustion products.

2. Installation must allow for a sufficient flow of

fresh air for the combustion air supply.

Combustion Air Requirements

Natural Gas 13 m³/hr minimum.

LPG / Butane 13 m³/hr minimum.

3. Position the appliance in its approximate

working position.

4. All air for burner combustion is supplied from

underneath the appliance. The legs must

always be fitted and no obstructions placed on

the underside or around the base of the

appliance, as obstructions will cause incorrect

operation and / or failure of the appliance.

5. Components having adjustments protected

(e.g. paint sealed) by manufacturer are only

allowed to be adjusted by a qualified service

agent. They are not to be adjusted by the

installation person.

NOTE:

Do not obstruct or block the appliances flue. Never

directly connect a ventilation system to the

appliance flue outlet.

NOTE:

Only non-combustible materials can be used in

close proximity to this appliance.

To facilitate easy operation, drainage and servicing

of the pasta / noodle cooker, a minimum of 600mm

clearance should be maintained at the front of the

appliance.

Any gas burning appliance requires adequate

clearance and ventilation for optimum and trouble-

free operation. The following minimum installation

clearances are to be adhered to:

LH / RH Side 50mm 0mm

Rear 50mm 0mm

This model is delivered completely assembled.

Ensure that the adjustable feet / rollers are securely

attached.

NOTE:

 This appliance is fitted with adjustable feet /

rollers to enable the appliance to be positioned

securely and level. This should be carried out on

completion of the gas connection. Refer to the

‘Gas Connection’ section below.

 The appliance rear leg housings are fitted with

Rear rollers to enable the appliance to be easily

moved for positioning and cleaning purposes.

NOTE:

ALL GAS FITTING MUST ONLY BE CARRIED OUT BY A

QUALIFIED SERVICE PERSON.

1. Cobra Pasta / Noodle Cookers do not require an

electrical connection, they function totally on

the gas supply only.

2. It is essential that the gas supply is correct for the

appliance to be installed and that adequate

supply pressure and volume are available. The

following checks should therefore be made

before installation:-

a. The Gas Type the appliance has been

supplied for is shown on coloured stickers

located above the gas entry point and next

to the rating plate. Check that this is correct

for the gas supply the appliance is being

installed for. The gas conversion procedure is

detailed in the ‘Gas Conversion Section’ of

this manual.

b. Supply Pressure required for this appliance is

shown in the “Specifications” section of this

manual. Check the gas supply to ensure that

adequate supply pressure exists.

c. Input Rate of this appliance is also stated on

the Rating Plate fitted to the inside of the

access door and in the ‘Specifications’

section of this manual. The input rate should

be checked against the available gas supply

line capacity. Particular note should be

taken if the appliance is being added to an

existing installation.

NOTE:

It is important that adequately sized piping runs

directly to the connection joint on the appliance,

with as few tees and elbows as possible to give

maximum supply volume.

3. Fit the supplied gas regulator into gas supply line

as close to the appliance as possible.

NOTE:

The gas pressure regulator provided with this

appliance is convertible between Natural Gas and

LPG as per ‘Gas Conversion Section’ in this manual.

Ensure regulator is converted to the correct gas

type that the appliance will operate on.

Regulator outlet pressure is fixed ex-factory for gas

type that regulator is converted to and it is NOT to

be adjusted.

Regulator connections are

" BSP female.

Connection to appliance is

" BSP male.

(Refer to 'Specifications' section for gas supply

location dimensions).

4. A suitable joining compound which resists the

breakdown action of LPG must be used on

every gas line connection, unless compression

fittings are used.

NOTE:

A Manual Isolation Valve must be fitted to individual

appliance supply line.

5. Locate the appliance into its final operating

position and using a spirit level, adjust the legs so

that the unit is level and at the correct height.

6. Connect the gas supply to the appliance.

7. Check Burner Operating Pressure is as shown in

‘Specifications’ section, ‘Gas Supply

Requirements’ tables. (Measure at ‘Burner

Operating Pressure Test Point’) on front of gas

control valve).

8. Check all gas connections for leakages using

soapy water or other gas detecting equipment,

with the main burner operating.

NOTE:

Measure operating pressure at Burner Operating

Pressure test point on gas control, this is to be

carried out with burner operating at 'High Flame'

setting. Operating pressure is ex-factory set,

through appliance regulator and not to be adjusted,

apart from when carrying out gas conversion, if

required. Refer to ‘Gas Conversion and

Specification’ Section for further details.

DO NOT USE A NAKED FLAME TO CHECK FOR GAS LEAKAGES.

Fig 2

Burner Operating

Pressure Test Point

Gas Control Valve

9. Verify the operating pressure remains correct.

10. Check the pilot flame size.

NOTE:

Water connection shall be installed in accordance

with local water regulations in force and the

applicable standard / code, e.g. EN 1717 in UK /

Ireland, PCA in Australia.

A cold water supply must be connected to water

inlet connection (R

" BSP), located 50mm from LH

side, 556mm from rear and 135mm from floor.

Water connection should be plumbed, in

accordance with National / Local Codes covering

installation.

Water inlet pressure must be as follows:-

Minimum water supply pressure 150 kPa (22 psi).

Maximum water supply pressure 550 kPa (80 psi).

Water is drained from appliance by means of a

valve located behind front control panel.

A waste water tundish must be fitted below the

appliance drain outlet. This should be a minimum of

127mm (5”) major diameter.

If required the drain outlet can be extended in

order to exit above the tundish. All drain piping

must be with materials suitable for conveying boiling

water.

Drain connection is R1" BSP drain / overflow.

The following commissioning checks must be carried

out before the Pasta / Noodle Cooker is handed

over for use, to ensure the unit operates correctly

and operator(s) understand the correct operating

procedure.

1. Before leaving new installation;

a. Check the following functions in accordance

with operating instructions specified in

‘Operation’ section of this manual.

 Light the Pilot Burner.

 Light the Main Burner.

b. Ensure that each operator has been

instructed in areas of correct lighting,

operation and shutdown procedures for the

appliance.

2. This manual must be kept by owner for future

reference and a record of Date of Purchase,

Date of Installation and Serial Number of Unit

recorded and kept with this manual. (These

details can be found on Rating Plate attached to

inner R/H side of front access door panel. Refer

to Figure 1 in 'Installation' section).

NOTE:

If for some reason, it is not possible to get the

appliance to operate correctly, shut Off the gas

supply and contact supplier of this unit.

1. Cobra Pasta / Noodle Cookers have been

designed to provide simplicity of operation and

100% safety protection.

2. Improper operation is almost impossible,

however bad operation practices can produce

a poor quality product. To use this Pasta /

Noodle cooker correctly, please read the

following sections carefully;

 Filling the Tank with Water.

 Lighting the Pilot Burner.

 Lighting the Main Burner.

 Draining and Cleaning.

CP4 / CN4 Pasta / Noodle Cooker Controls

Burner Control

OFF Position

PILOT Burner

HIGH Flame

LOW Flame

Gas Control Knob

Piezo Igniter

(Behind Access Door)

Water Control Valve

NEVER OPERATE APPLIANCE WITH GAS CONTROL VALVE SET

BETWEEN ‘HIGH’ FLAME AND ‘PILOT’ POSITION.

 A commercial heavy duty, gas fired Pasta /

Noodle Cooker using a fast fry infra red burner

system.

 Available in single model type only.

 This model is fitted with a single main burner with

a pilot burner and is controlled by a single gas

controller with flame failure protection to control

both the main burner and the pilot.

 Open tank design to simplify cleaning operation.

1. Check gas supply is turned On.

2. Check that no foreign articles are in the tank.

NOTE: Tank capacity - 40 Ltrs of water.

1. Before filling tank, always check that the drain

valve, behind the door, is closed. A locking slide

is provided on the valve and this should always

be locked ‘Closed’ position during use.

2. Turn water supply On. Open appliance water

valve and fill tank with water.

3. Water level will remain at a constant height as

there is an overflow at front of tank.

4. During cooking, water level will reduce as it

evaporates as steam when boiling and when it

overflows as loaded baskets are dropped into

tank.

5. To maintain correct water level, water tap

should be adjusted to give a water flow out of

water supply nozzle that just causes water to

continually flow out of overflow.

This method provides:

 Maintained water level for cooking.

 Skimming or flushing effect to prevent

the cooking water becoming gummed

up with residue.

GREAT CARE MUST BE TAKEN BY OPERATOR, TO USE THE PASTA COOKER SAFELY, TO GUARD AGAINST RISK OF INJURY AND

FIRE.

 DO NOT LEAVE PASTA / NOODLE COOKER UNATTENDED DURING OPERATION.

 DO NOT OVER FILL WATER IN PASTA / NOODLE COOKER ABOVE UPPER FILL LEVEL MARK.

 DO NOT ALLOW WATER IN PASTA / NOODLE COOKER TO FALL BELOW LOWER LEVEL MARK.

 DO NOT USE FLAMMIBLE SOLVENTS AND CLEANING AIDS ON OR IN CLOSE PROXIMITY TO PASTA / NOODLE

COOKER WHILST COOKER IS STILL HOT.

DANGER OF FIRE EXISTS IF THE WATER LEVEL IS BELOW THE

MINIMUM “LO” INDICATED LEVEL

1. With pasta / noodle cooker tank full of water,

the pilot burner can be lit.

2. Check gas supply is turned On at mains supply.

3. Depress and rotate gas control knob to the

‘Pilot’ position and hold knob depressed.

4. Open front access door of appliance, depress

piezo igniter on bulkhead panel, until pilot burner

ignites.

5. Continue holding gas control knob depressed

for approx. 10 / 15 seconds after igniting pilot

burner, then release, pilot burner should remain

alight.

6. Ensure pilot burner is alight, by checking that

pilot flame is alight with access door open.

7. If pilot burner does not ignite, repeat Items 1 to 6.

1. Depress and rotate gas control knob to the High

Flame position, main burner will ignite

automatically off the pilot burner.

2. Gas control knob can be regulated between

High Flame and Low Flame position to regulate

cooking temperature.

3. It will take approximately 30 minutes to heat the

water in the tank from 20°C to 100°C.

IMPORTANT:

 THE USE OF ROCK SALT IS NOT PERMITTED IN THIS

MACHINE .

 NEVER add salt to cold water - always ensure that

the water in the pasta / noodle cooker is boiling

before adding salt.

 Clean the pan regularly after each use.

To the ‘Pilot’ Position

a. Depress and rotate gas control valve anti-

clockwise to the Pilot position.

b. Main burner will extinguish and Pilot will

remain alight.

To the ‘Off’ Position

a. Depress and rotate gas control valve fully

anti-clockwise to Off position.

b. Pilot burner will extinguish.

INDICATES MINIMUM (SAFE) LEVEL.

WATER LEVEL SHOULD BE TOPPED UP.

CORRECT LEVEL FOR WATER WHEN

COOKING, KEEP TOPPED UP.

CORRECT LEVEL FOR FRYING MEDIUM WHEN AT

FRYING TEMPERATURE, KEEP TOPPED UP

INDICATES CORRECT FRYING MEDIUM LEVEL

WHEN COLD

a. Lift the locking slide on valve handle (Fig 1) to

release valve.

b. While holding the locking slide in the

withdrawn position, rotate the handle

anti-clockwise (Fig 2) to open the valve.

c. When the valve is closed, the locking slide will

drop down over the locking valve to prevent

accidental opening of valve (see Fig 1).

To keep your pasta / noodle cooker clean and

operating at peak efficiency, observe the following

procedures:-

NOTE:

 DO NOT clean appliance using high pressure

water or steam jets.

 DO NOT pour water directly over appliance.

 DO NOT use wire brushes.

 DO NOT use combustible liquids to clean

appliance.

 DO NOT use harsh abrasive detergents, sharp

scrapers, strong solvents or caustic detergents as

they will damage appliance.

 DO NOT use any chloric or bleaching detergents

to clean appliance.

 Ensure that any detergent or cleaning material

have been completely removed after each

cleaning.

 DO NOT use saline or sulfuric acid preparations

for descaling the appliance.

 Ensure that protective gloves are worn during the

cleaning process.

 Clean the pan regularly after each use.

DO NOT USE FLAMMIBLE SOLVENTS AND CLEANING AIDS ON

OR IN CLOSE PROXIMITY TO THE PASTA / NOODLE COOKER

WHILST THE IS STILL HOT.

Fig 1

Locking

Slide

HOT WATER WILL BURN - DO NOT RUSH THIS JOB.

Fig 2

Locking

Slide

1. Water should be drained and re-filled regularly.

Open drain valve slowly to minimise splashing.

Waste water will drain into a tundish fitted below

the appliance drain outlet.

2. When the tank is empty, open drain valve fully

and check for any particles or residue lodged in

the valve. Clean out the valve with a stiff nylon

brush. Do not use a wire brush or metal rods as

these will damage the valve seating and will

eventually lead to valve leakage.

3. If obstruction in the valve cannot be removed

with a brush, use a wooden probe to dislodge

the obstruction.

4. Clean the control panel using a damp cloth

lightly moistened with a solution of mild

detergent and hot water. Dry the control panel

thoroughly using a dry clean cloth.

5. Clean interior of pan regularly at the end of

each day. Do not use wire brushes on the pan.

Clean using a mild detergent and a hot water

solution using soft cloth or a soft bristled brush.

Dry the appliance thoroughly using a dry clean

cloth.

6. Once the daily cleaning operation is

completed, ensure the drain valve has been

closed and secured.

7. At the end of each day or at end of each shift,

 Clean the exterior of the pasta / noodle

cooker using a mild detergent and hot water

solution using soft cloth or a soft bristled brush.

 Clean the pasta / noodle baskets using a

mild detergent and hot water solution using a

soft cloth or a soft bristled brush. Rinse in fresh

water and thoroughly dry using a dry cloth.

NOTE:

 If pasta / noodle cooker usage is very high, we

recommend that the weekly cleaning procedure

is carried out more frequently.

 Ensure protective gloves are worn during

cleaning.

 DO NOT use harsh abrasive detergents, strong

solvents, sharp scrapers or caustic detergents as

they will damage the surface of the Pasta /

Noodle cooker.

 Ensure that the water supply is free of ferrous

particles. Any such particles deposited in the

bottom of the tank may cause the tank to rust.

Thoroughly clean the interior and exterior of the

pasta / noodle cooker regularly. Do not use wire

brushes on the pan. Clean using a mild detergent

and hot water solution using soft cloth or a soft

bristled brush. Dry the appliance thoroughly using a

dry clean cloth.

NOTE: In order to prevent rust forming on the steel

components, ensure that the detergent or cleaning

material has been entirely removed after each

cleaning process.

Stainless Steel Surfaces

a. Clean the interior and exterior surfaces of the

pasta / noodle cooker with hot water, a mild

detergent solution and a soft scrubbing brush.

Note that the gas control knob is a push fit onto

the gas valve spindle and can be removed to

allow cleaning of the front of the control panel.

b. Baked on deposits or discolouration may require

a good quality stainless steel cleaner or stainless

steel wool. Always apply cleaner when the

appliance is cold and rub in the direction of the

grain.

c. Dry all components thoroughly with a dry cloth

and polish with a soft dry cloth.

NOTE:

All maintenance operations should only be carried

out by a qualified service person.

To achieve the best results, cleaning must be

regular and thorough and all controls and

mechanical parts should be checked and adjusted

periodically by a qualified service person. If any

small faults occur, have them attended to promptly.

Don't wait until they cause a complete breakdown.

It is recommended that the appliance is serviced

every 6 months.

If appliance is not used for long periods, close gas

shut-off valve upstream of the appliance and clean

the appliance thoroughly.

The appliance should be inspected and the gas

exhaust flue cleaned by an authorized service

person at least every 6 months.

DO NOT ATTEMPT TO MOVE THE PASTA / NOODLE COOKER

WHILST IT IS FULL OF WATER.

PASTA / NOODLE COOKER

Pilot Burners will not ignite or

ignites with difficulty and will not

stay alight.

Check gas supply is turned On. Turn On gas supply.

Check gas supply is low or empty. Replenish gas supply.

Thermocouple connection loose. Tighten thermocouple connection.

Replace any damaged connectors.

Over temperature lead connection to

interrupter on thermocouple is loose.

Loose connections will cause

resistance to millivolt circuit and result

in pilot outage.

Tighten over temperature lead to the

interrupter on the thermocouple.

If sufficient pilot flame cannot be

obtained, remove pilot orifice from

pilot burner and check for blockage of

pilot burner and /or gas line also

check that correct size gas pipe has

been used.

If connections OK, check for gas at pilot

burner by manually lighting pilot burner.

Call service provider.

If pilot can be lit but flame too small to

impinge on thermocouple.

Check pilot injector for restriction. Clean

or replace Pilot Injector.

Check gas supply.

If pilot flame OK but goes out after

control knob released (after holding in

for approx. 30 secs).

Check for faulty thermocouple.

Call service provider.

If all of above in pilot and

thermocouple system checks out

satisfactorily but problem still persists.

Gas control valve is defective and needs

replacement.

Pilot Burner delay in ignition of

main burners.

Check operating pressure as stated in

‘Installation’ section.

Check gas supply.

Call service provider.

Check pilot flame size. Pilot flame for main burner ignition should

be approximately 1 inch long. Check pilot

burner injector size is correct. (See

‘Specifications’ section).

Check pilot injector for restriction. Clean

or replace Pilot Injector.

Main Burners will not ignite or

ignites with difficulty.

Insufficient gas pressure.

Main injector is blocked.

Gas valve is faulty.

Check gas pressure and adjust as

necessary.

Remove main injector and clean or

replace.

Replace. Call service provider.

This section provides an easy reference guide to the more common problems that may occur during

operation of your equipment. The fault finding guide in this section is intended to help you correct, or at

least accurately diagnose problems with your equipment.

Although this section covers the most common problems reported, you may encounter a problem not

covered in this section. In such instances, please contact your local authorised service agent who will make

every effort to help you identify and resolve the problem. Please note that the service agent will require the

following information:-

 Model Trade Name and Serial Number of the Appliance. (both can be found on the Technical

Data Plate located on the appliance.

CN4 / CP4 Pasta Cooker

NOTE:

 These conversions should only be carried out by

qualified persons. All connections must be

checked for leaks before re-commissioning the

appliance.

 Adjustment of components that have

adjustments / settings sealed (e.g. paint sealed)

can only be adjusted in accordance with the

following instructions and shall be re-sealed

before re-commissioning this appliance.

 For relevant gas specifications refer to ‘Gas

Specifications Tables’ at rear of this section.

- NAT Gas / LPG / Butane Only.

1. Unscrew cap on regulator and rotate pin to the

setting shown in ‘Gas Specifications’ tables

overleaf.

2. Refit cap to regulator.

NOTE:

Gas regulator supplied is convertible between

Natural Gas and LP Gas, but it’s outlet pressure is

fixed ex-factory and is NOT to be adjusted.

1. Open the cabinet door.

2. Remove main burner injector and replace with

correct size injector as shown in Gas

Specifications Table.

1. Remove the following:-

 Gas supply tube to pilot burner.

NOTE:

Appliances fitted with piezo igniter electrodes,

remove electrode from mounting bracket before

unscrewing pilot supply tube.

2. Remove pilot burner injector and replace with

correct size injector as shown in ‘Gas

Specifications Table’ at rear of this section.

3. Refit the following:-

 Gas supply tube to pilot burner.

 Piezo igniter electrode.

Main Burner

Injector

Thermocouple

Piezo

Igniter

Pilot Burner

NOTE, Pin rotated

for Natural Gas

NOTE, Pin rotated

for LPG / Butane

1. Set low fire screw as shown in Gas Specifications

Table at rear of this section.

2. Connect a manometer to upper test point

(Burner Operating Pressure) on gas control valve.

Turn ‘On’ gas and light the main burner

3. Ensure burner operating pressure is as shown in

Gas Specifications Table at rear of this section.

4. Check the flame size on the ‘Low’ position.

NOTE:

‘Low Fire Screw’ should be sealed with coloured

paint on completion of low fire adjustment.

5. Refit the following:-

 Gas control knob.

 Water control knob.

 Control Panel.

On completion of gas conversion, replace gas type

labels located at:-

- Rear of unit, above gas connection.

- Beside rating plate.

Burner Operating

Pressure

Gas Control

Valve

Low Fire Adjust

Screw

Before leaving installation;

1. Check all gas connections for leakage using

soapy water or other gas detecting equipment.

2. Carry out a ‘Commissioning’ check of the

appliance as shown in Installation Section of this

manual.

3. Ensure any adjustments done to components

that have adjustments / settings paint sealed,

these are to be re-sealed.

NOTE:

If for some reason it is not possible to get appliance

to operate correctly, shut ‘Off’ gas supply and

contact supplier of this appliance.

DO NOT USE A NAKED FLAME TO CHECK FOR GAS LEAKAGES.

- Australia

- New Zealand:

- UK Only:

Category: II

2H3P.

Flue Type: A

NOTE: (*) Measure burner operating pressure at upper test point (Burner Operating Pressure) on gas control

valve located behind control panel, this is to be carried out with burner operating at ‘High Flame’

setting. Operating pressure is ex-factory set, through the appliance regulator and is not to be

adjusted, apart from when carrying out gas conversion, if required. Refer to the details in this section

for further details.

Main Burner Injectors

Ø 3.10mm Ø 1.90mm

Pilot Burner Injectors

0.62 0.35

Low Fire Screw

Ø 1.55mm

2 Turns Out (c.c.w.)

Ø 1.55mm

Fully In (c.w.)

High Fire Screw

Fully Out (c.c.w.) Fully Out (c.c.w.)

Supply Pressure

1.13 - 3.40 kPa 2.75 - 4.50 kPa

Burner Operating Pressure (*)

0.92 kPa 2.6 kPa

Gas Regulator Cap Screw

Main Burner Injectors

Ø 3.10mm Ø 1.90mm

Pilot Burner Injectors

0.62 0.35

Low Fire Screw

Ø 1.55mm

2 Turns Out (c.c.w.)

Ø 1.55mm

Fully In (c.w.)

High Fire Screw

Fully Out (c.c.w.) Fully Out (c.c.w.)

Supply Pressure

20 mbar 37 mbar

Burner Operating Pressure

9.5 mbar 27.7 mbar

Gas Regulator Cap Screw

Main Burner Injectors

Ø 3.10mm Ø 1.80mm

Pilot Burner Injectors

0.62 0.35

Low Fire Screw

Ø 1.55mm

2 Turns Out (c.c.w.)

Ø 1.55mm

Fully In (c.w.)

High Fire Screw

Fully Out (c.c.w.) Fully Out (c.c.w.)

Supply Pressure

1.13 - 3.40 kPa 2.75 - 4.50 kPa

Burner Operating Pressure (*)

0.92 kPa 2.6 kPa

Gas Regulator Cap Screw

- All Other Markets:

(*) NOTE:

Measure burner operating pressure at upper test point (Burner Operating Pressure) on gas control

valve located behind control panel, this is to be carried out with burner operating at ‘High Flame’

setting. Operating pressure is ex-factory set, through the appliance regulator and is not to be

adjusted, apart from when carrying out gas conversion, if required. Refer to the information in this

section for further details.

Main Burner Injectors

Ø 3.10mm Ø 1.80mm Ø 1.70mm

Pilot Burner Injectors

0.62 0.35 0.35

Low Fire Screw

Ø 1.55mm

2 turns out (c.c.w.)

Ø 1.55mm

Fully In (c.w.)

Ø 1.55mm

Fully In (c.w.)

High Fire Screw

Fully Out (c.c.w.) Fully Out (c.c.w.) Fully Out (c.c.w.)

Supply Pressure

1.13 - 3.40 kPa 2.75 - 4.50 kPa 2.75 - 4.50 kPa

Burner Operating Pressure (*)

0.92 kPa 2.6 kPa 2.6 kPa

Gas Regulator Cap Screw

018094 Thermocouple Interrupted.

229702 Overtemp 115°.

032190 Main Burner Injector (LPG/Propane) - ø 1.90mm.

032180 Main Burner Injector (LPG) - ø 1.80mm.

032310 Main Burner Injector (Nat Gas) - ø 3.10mm.

032170 Main Burner Injector (Butane) - ø 1.70mm.

018090K Pilot Burner.

018092 Pilot Injector (LPG / Butane) 0.35.

018091 Pilot Injector (Nat Gas) - 0.62.

229699 Gas Control Valve.

242363 Gas Control Knob (Cobra).

240553 Water Ball Valve ¼ Turn, Lever Handle.

018095 Piezo H.T. Lead.

227508 Piezo Ignitor.

022575 Burner Kit.

238674 Pasta Basket LH 1/6 165 x 125mm.

238819 Pasta Basket RH 1/6 165 x 125mm.

229682 Pasta Basket Support Frame.

227856 Door Magnet Catch.

019390 Water Drain Ball Valve.

229823 Overflow Hose.

242352 Adjustable Leg - (150mm) c/w Leg Plate.

229674 Rear Roller Assembly.

240507 Noodle Basket.

240510 Noodle Basket Support Tray.

228531 Gas Regulator ¾” BSP F/F Convertible (Nat. Gas, LPG, Butane).

CP4 Pasta Cooker

229836 Pasta Cooker Basket 1/4 165 x 165mm.

229837 Pasta Cooker Basket 1/2 320 x 165mm.

240516 Noodle Kit (includes 5 Noodle Baskets + Noodle Basket Support Frame).

CN4 Noodle Cooker

238674 Pasta Basket LH 1/6 165 x 125mm.

238819 Pasta Basket RH 1/6 165 x 125mm.

229836 Pasta Cooker Basket 1/4 165 x 165mm.

229837 Pasta Cooker Basket 1/2 320 x 165mm.

229682 Pasta Basket Support Frame.

Replacement Parts List

When ordering spare parts, please quote part number and description as listed below. If part required is not

listed below, request part by description and quote model number and serial number which is shown on

rating plate.

IMPORTANT:

Only genuine qualified replacement parts should be used for the servicing and repair of this appliance.

he instructions supplied with the parts should be followed when replacing components.

For further information and servicing instructions, contact your nearest qualified service branch (contact details are

as shown on the reverse of the front cover of this manual).

CN4 / CP4

232061 232060 232062 232061 232060 244511

Also requires Pasta Basket

Support Frame Part No.

229682

Page is loading ...

Moffat CN4 Operating instructions

Brand: Moffat

Model: CN4

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Moffat CN4 Operating instructions

This manual is also suitable for

Moffat CN4 Operating instructions

Related papers

Other documents