Delta Children Solutions Changing Table Assembly Instructions

Brand
Delta Children
Model
Solutions Changing Table
Type
Assembly Instructions

This manual is also suitable for

Style #:
Lot:
Date:
___________
___________
___________
©2011 DELTA ENTERPRISE CORP.
A
Changing Table
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Top Shelf.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
DECEMBER 30, 2011, 22811, R0
Conforms to
ASTM F2388
Safety Standards
2
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
WARNING
FALL HAZARD - to prevent death or serious injury, always keep child within arm’s reach.
Read all instructions before use of the changing table.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.
Inspect the changing table periodically. Do not use the changing table if it is damaged or
broken. Contact Delta Children’s Products with any questions.
Tighten all loose screws and bolts before each use.
The maximum recommended weight of the child is 30lbs for the changing table.
Use only the pad provided by Delta Children’s Products.
Always secure the pad to the changing surface by inserting the strap through the hole in
the middle of the pad. See Instructions.
PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
3
H. Top Shelf x 1
J. Bottom Shelf x 2
K. Foam Pad x 1
C. Cap Rail x 2
D. Upper Back Rail x 1
E. Top Front Rail x 1
F. Front Middle Rail x 1
G. Bottom Rail x 4
A. Left Side x 1
B. Right Side x 1
L. Restraint Harness x 1
Part # 22796
Part # 22797
Part # 22798
Part # 22799
Part # 22800
Part # 22801
Part # 22802
Part # 22803
Part # 22804
Part # 22830
Part # 21691
M. Drawer Front x 1
Part # 22805
N. Drawer Back x 1
Part # 22806
P. Drawer Left Side x 1
Part # 22807
R. Drawer Right Side x 1
Part # 22808
S. Drawer Bottom x 1
Part # 22809
T. Drawer Support x 1
Part # 22810
EE. Back Middle Rail x 1
Part # 22931
FF. Back Middle Panel x 1
Part # 22932
:ST R A P
4
M4 Allen Wrench Supplied
Z. Φ6x25 mm Wood Dowel x 4
U. M6 x 35 mm Bolt x 20
V. M6 x 20 mm Bolt x 1
Y. 25mm Flat Head Wood Screw x 5
BB. Nut x 1
AA. Nylon Washer x 2
Phillips Screwdriver
Pliers or Adjustable
Wrench Required
for Assembly
(not supplied)
No drills necessary. Do not
use power screwdriver.
HARDWARE KIT PART #22812 FOR COLOR 100 OR #22813 FOR COLOR 604 OR
#22814 FOR COLOR 260. SEE COVER PAGE.
Part # 5464
Part # 5461
Part # 5065
Part # 5525
Part # 4065
Part # 5508
Part # 1177
W. Knob x 2
Part # 22815
X. M4 x 30 mm Bolt x 2
Part # 5606
CC. 35 mm Flat Head Wood Screw x 4
Part # 5517
DD. Plastic Barrel Nut x 4
Part # 5497
SECTION 1: CHANGING TABLE ASSEMBLY
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
5
M4 Allen Wrench
Supplied
E
G
U. M6 x 35 mm Bolt x 8
F
D
A. Left Side x 1
D. Upper Back Rail x 1
E. Top Front Rail x 1
F. Front Middle Rail x 1
G. Bottom Rail x 4
A
Attach (1) Upper Back Rail (Part D), (1) Top Front Rail (Part E), (1) Front Middle Rail (Part F), (1) Back
Middle Rail (Part F) and (4) Bottom Rails (Part G) to the Left Side (Part A) with (8) M6 x 35 mm Bolts
(Part U) using the M4 Allen Wrench as shown.
BE SURE THE GROOVES FACE TO THE INSIDE.
G
EE
U
U
U
U
U
U
U
U
EE. Back Middle Rail x 1
EE, Holes to INSIDE
Groove to TOP.
SECTION 1: CHANGING TABLE ASSEMBLY
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
6
From Step 1
J
J
H
H. Top Shelf x 1 J. Bottom Shelf x 2
Lay the Left Side on the floor, rails up. Slide the Top Shelf (Part H) in the grooves on the Top Front Rail
and Upper Back Rail, into the groove on the Left Side. Slide (2) Bottom Shelves (Part J) in the grooves
on the Bottom Rails, into the grooves on the Left Side. Slide the Back Middle Panel (Part FF) in the
grooves on the Upper Back Rail and Back Middle Rail to the Left Side as shown.
FF. Back Middle Panel x 1
FF
SECTION 1: CHANGING TABLE ASSEMBLY
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
7
From Step 2
M4 Allen Wrench
Supplied
B. Right Side x 1
Attach (1) Right Side (Part B) to the assembly from step 2 with (8) M6 x 35 mm Bolts (Part U) using the
M4 Allen Wrench as shown.
U. M6 x 35 mm Bolt x 8
U
B
U
U
U
U
U
U
U
SECTION 1: CHANGING TABLE ASSEMBLY
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
8
From Step 3
M4 Allen Wrench Supplied
C. Cap Rail x 2
U. M6 x 35 mm Bolt x 4
Attach (2) Cap Rails (Part C) to the assembly from step 3 with (4) M6 x35 mm Bolts (Part U) using the
M4 Allen Wrench as shown.
U
U
U
U
C
C
SECTION 1: CHANGING TABLE ASSEMBLY
STEP 5
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
9
From Step 4
M4 Allen Wrench Supplied
BB. Nut x 1
V. M6 x 20 mm Bolt x 1
Pliers or Adjustable Wrench
(Not Supplied)
L. Restraint Harness x 1
AA. Nylon Washer x 2
Align the hole in the middle of the strap of the Restraint Harness (Part L) with the hole in the Top Shelf.
Insert (1) M6 x 20 mm Bolts (Part V) through a Nylon Washer (Part AA), the restraint strap and the hole
in the shelf. Add (1) Nylon Washer (Part AA) with a Nut (Part BB). Hold the nut with a Pliers or
Adjustable Wrench.
L
AA
BB
AA
V
SECTION 1: CHANGING TABLE ASSEMBLY
STEP 6
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
10
From Step 5
K
1. Insert the strap through the hole in the Foam Pad (Part K).
2. Place Foam Pad (Part K) on Top Shelf (Part H).
K. Foam Pad x 1
Click !
2
1
3
SECTION 2: DRAWER ASSEMBLY
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
11
Attach (1) Drawer Left Side (Part P) and (1) Drawer Right Side (Part R) to (1) Drawer Front (Part M)
with (4) Φ6x25 mm Wood Dowels (Part R) and (4) 25mm Flat Head Wood Screws (Part Y), Tighten with
the Phillips Screwdriver.
M
M. Drawer Front x 1
P. Drawer Left Side x 1
R. Drawer Right Side x 1
Y. 25mm Flat Head Wood Screw x 4
Phillips Screwdriver
not supplied
P
R
Y
Z
Z. Φ6x25 mm Wood Dowel x 4
Z
Y
BACK
SECTION 2: DRAWER ASSEMBLY
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
12
1. Slide (1) Drawer Bottom (Part S) in the grooves on the Drawer Left Side and Drawer Right Side, into
the groove on the Drawer Front.
2. Insert the Drawer Support (Part T) as shown.
S
BOTTOM
From Section 2 Step 1
T. Drawer Support x 1
S. Drawer Bottom x 1
T
SECTION 2: DRAWER ASSEMBLY
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
13
From Section 2 Step 2
Y. 25mm Flat Head Wood Screw x 1
CC. 35mm Flat Head Wood Screw x 4
Phillips Screwdriver
not supplied
N. Drawer Back x 1
Attach (1) Drawer Back (Part N) to the assembly from section 2 step 2 with (4) 35mm Flat Head Wood
CC
CC
Y
N
BOTTOM
DD
DD
DD. Plastic Barrel Nut x 4
Screws (Part CC) , (4) Plastic Barrel Nut (Part DD) and (1) 25mm Flat Head Wood Screws (Part Y). Use
the Flat Head Screwdriver to hold the Plastic Barrel Nut in the proper alignment. Tighten with the
Phillips Screwdriver.
SECTION 2: DRAWER ASSEMBLY
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
14
From Section 2 Step 3
Phillips Screwdriver
not supplied
1. Attach (2) Knobs (Part W) to the assembly from section 2 step 3 with (2) M4 x 30 mm Bolts (Part X),
Tighten with the Phillips Screwdriver.
2. Insert the drawer as shown.
M
W. Knob x 2
X. M4 x 30 mm Bolt x 2
X
W
W
X
FINAL
TO FASTEN STRAP - PUTH BUCKLE SIDE TOGETH-
ERBESURE BUCKLE IS FULLY FASTENED TO
SECURE CHILD SAFFELY
TO RELEASE PRESS BOTH TABS AND PULL APART
15
RESTRAINT HARNESS SYSTEM USE:
. PLACE THE INFANT ON THE CHANGING TABLE FOAM PAD.
. POSITION THE RESTRAINT HARNESS OVER THE MIDDLE OF THE INFANT’S
TORSO AND INSERT THE BUCKLED ENDS INTO EACH OTHER UNTIL THE LOCK
SHUT WITH A CLICK.
. GENTLY PULL THE LOOSE END OF THE STRAP TO LIGHTLY SNUG THE
RESTRAINT HARNESS AROUND THE INFANT.
MAINTENANCE
. CHECK FASTENERS PERIODICALLY FOR TIGHTNESS. DO NOT OVER TIGHTEN.
THIS MAY CAUSE DISTORTION OR BREAKAGE.
WARNING : FALL HAZARD
ALWAY KEEP CHILD WITHIN ARMS REACH.
Warranty: This Delta product is warranted to be free from defects for a period
of 90 days from the date of purchase under normal use. This warranty extends
only to the original retail purchaser and is valid only when supplied with proof of
purchase, or if received as a gift, when the registration is on file with Delta.
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
Please do not return this item to the store before contacting
us about missing parts or with any questions.
To register your product for important safety alerts and updates to
your product please visit www.DeltaChildren.com
To report a problem, please log on to www.DeltaChildren.com and
click the Consumer Care Tab, or contact us by phone at
(212) 645-9033.
In the event that you need to contact our customer service
department please have the Style Number and Lot Number available.
Use the space below to make note of those numbers. They can be
found on the label on the Top Shelf.
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________
(you should also keep your receipt)
COLOR
FTY
REV
STYLE No: 7584
A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Delta Children Solutions Changing Table Assembly Instructions

Brand
Delta Children
Model
Solutions Changing Table
Type
Assembly Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents