Sea Eagle FRAMESEAT2 Operating instructions

Sea Eagle
Brand
Sea Eagle
Model
FRAMESEAT2
Type
Operating instructions

This manual is also suitable for

Sea Eagle FRAMESEAT2 is double swivel seat for FishSkiff16 that allows you to rotate your seat while sitting in it. It can be installed either in the front or in the rear position of your boat. Assembly is easy and can be done with basic tools like #2 phillips screwdriver or 7/16” wrench for hex head screws. Seat capacity is 250 lbs per seat. Sea Eagle FRAMESEAT2 helps you to enjoy your fishing trip and provides you with additional comfort and safety.

Sea Eagle FRAMESEAT2 is double swivel seat for FishSkiff16 that allows you to rotate your seat while sitting in it. It can be installed either in the front or in the rear position of your boat. Assembly is easy and can be done with basic tools like #2 phillips screwdriver or 7/16” wrench for hex head screws. Seat capacity is 250 lbs per seat. Sea Eagle FRAMESEAT2 helps you to enjoy your fishing trip and provides you with additional comfort and safety.

6/2019
Double Swivel Seat
(FRAMESEAT2)
Assembly Instructions for FishSkiff16
Kit Includes: Aluminum base assembly, folding seats with locking swivel plate, pedestals, and
hardware.
Seat to Pedestal Hardware Pedestal to Frame
8 - 1/2” Hex Head Screws 8 - 1¼” Hex Head Screws
8 - Wingnuts 8 - Wingnuts
Frame Hardware Tools (optional)
8 - 2” Phil Truss Screw #2 phillips screwdriver
8 - three arm plastic knob 7/16” Wrench for hex head screws
Pedestal to Seat
Attach the pedestal to the seat swivel with the short ½”
screws and wingnuts.
Tighten wingnuts after all the screws have been
inserted.
Hold bolt head with wrench if needed.
Sea Eagle Boats
Run the 2” phill truss screws up though long bar. Lay
end of short bar over bolt and twist knob onto screw. Do
not tighten.
Use remaining bars, screws, and knobs to assemble
frame.
Tighten knobs after all the screws have been inserted. Use screwdriver to hold screw head if
needed.
Attach pedestals to frame using 1¼” hex
head screws.
Turn seat on its side. Match the frame
holes to pedestal holes.
Insert screws up through bottom of
frame bar and thread wingnut onto
screw.
Do not tighten nuts until all screws have
been inserted.
Completed double seat assembly.
Sea Eagle Boats
Place the double seat rig over the hold down straps
in the FSK16 in either the front or rear position.
Run free end of strap through both rings then back
through front ring
Pull the strap tight.
CAUTION!: Straps can stretch when wet. Wet the
strap before leaving shore and retighten.
Check frequently and tighten as need
Double Seat installed in rear position. To swivel, sit in seat, pull locking bar forward
and push with legs to turn seat.
We hope you enjoy the FSK16 and Fishing Rig and use caution while out on the water, follow
the Sea Eagle Boating Safety Basics and boat safely.
Sea Eagle Boats
Warnings!:
Seat capacity: do not exceed 250 lbs per seat.
Seat: AVOID SERIOUS OR FATAL INJURY DUE TO ROTATION OF SEAT. LOCK SWIVEL WHEN
SPEED EXCEEDS 5 MPH.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Sea Eagle FRAMESEAT2 Operating instructions

Sea Eagle
Brand
Sea Eagle
Model
FRAMESEAT2
Type
Operating instructions
This manual is also suitable for

Sea Eagle FRAMESEAT2 is double swivel seat for FishSkiff16 that allows you to rotate your seat while sitting in it. It can be installed either in the front or in the rear position of your boat. Assembly is easy and can be done with basic tools like #2 phillips screwdriver or 7/16” wrench for hex head screws. Seat capacity is 250 lbs per seat. Sea Eagle FRAMESEAT2 helps you to enjoy your fishing trip and provides you with additional comfort and safety.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents