Miller PROHEAT INSULATION Owner's manual

Brand: Miller

Model: PROHEAT INSULATION

Type: Owner's manual

This manual is also suitable for

MG000000

Miller PROHEAT INSULATION is a device that can be used for heating various objects. It allows for the cutting of insulation in multiples of 24 inches, with double stitched lines at 24-inch intervals to prevent fraying. The heating cable length requirements vary depending on the number of cable turns and insulation length, with a table provided in the manual to assist in determining the appropriate length.

OWNER’S MANUAL

ORIGINAL INSTRUCTIONS - PRINTED IN USA

FORM: OM-274540B 2021-01

For ProHeat Insulation w/Straps

1. Safety Symbol Definitions

DANGER! − Indicates a hazardous situation which, if not avoided,

will result in death or serious injury. The possible hazards are

shown in the adjoining symbols or explained in the text.

DANGER ! - Indique une situation dangereuse qui, si elle n’est pas

évitée, entraînera la mort ou des blessures graves. Les éventuels

risques sont représentés par les symboles joints ou expliqués dans

le texte.

Fsafe1 2013-10

Beware of electric shock from wiring. Disconnect input power be-

fore installing this kit. Reinstall all panels and covers.

Attention aux décharges électriques au contact des câbles. Couper

l’alimentation électrique avant d’installer ce kit. Réinstaller tous les

panneaux et couvercles.

Fsafe7 2013-10

Indicates a hazardous situation which, if not avoided, could result in

death or serious injury. The possible hazards are shown in the

adjoining symbols or explained in the text.

Indique une situation dangereuse qui, si elle n’est pas évitée,

entraînera la mort ou des blessures graves. Les éventuels risques

sont représentés par les symboles joints ou expliqués dans le texte.

Fsafe2 2013-10

Wear safety glasses with side shields.

Porter des lunettes de sécurité avec écrans latéraux.

Fsafe8 2013-10

NOTICE

Indicates statements not related to personal injury.

Signale des consignes non associées aux dommages corporels.

Indicates special instructions.

Fournit des instructions spéciales.

Fsafe3 2013-10

Have only trained and qualified persons install, operate, or service

this unit. Read the safety information at the beginning of these

instructions and in each section. Call your distributor if you do not

understand the directions. For WELDING SAFETY and EMF in-

formation, read owner’s manual(s).

Ne confiez l’installation, l’exploitation ou l’entretien de cet appareil

qu’à des personnes compétentes et qualifiées. Lire les directives

de sécurité au début de ces instructions et dans chaque section.

Appeler votre distributeur si vous ne comprenez pas les

directives. Lire le(s) manuel(s) d’utilisateur pour des

renseignements sur la SÉCURITÉ DE SOUDAGE et les champs

électromagnétiques.

Fsafe152013-10

Hot parts can burn. Allow cooling period before working on

equipment. Do not touch hot parts bare handed. To handle hot

parts, use proper tools and/or wear heavy, insulated welding

gloves and clothing to prevent burns.

Les pièces chaudes peuvent provoquer des brûlures. Prévoir

une période de refroidissement avant de travailler à l’équipe-

ment. Ne pas toucher à mains nues les parties chaudes. Ne pas

toucher aux pièces chaudes, utiliser les outils recommandés et

porter des gants de soudage et des vêtements épais pour éviter

les brûlures.

Fsafe13 2015-06

CALIFORNIA PROPOSITION 65 WARNINGS

WARNING: Cancer and Reproductive Harm − www.P65Warnings.ca.gov

PROPOSITION CALIFORIENNE 65 AVERTISSEMENTS

AVERTISSEMENT : cancer et troubles de la reproduction − www.P65Warnings.ca.gov.

Fsafe26 2018-01

OM-274540 Page 2

2. Insulation Configurations

1 Cut Line

Insulation is configured to be cut in

multiples of 24 in. (610 mm)

lengths. There are double stitched

lines at 24 in. Intervals. To prevent

fraying, cut to desired length be-

tween the lines.

Ref. 274541-B

120.50 in. (3061 mm)

96.00 (2438 mm)

72.00 in. (1829 mm)

48.00 in. (1219 mm)

24 in. (610 mm)

16.50 in.

(419 mm)

3. Heating Cable Length Requirements For Various

Number Of Cable Turns And Insulation Length

Table lists the approximate length of cable required to wind various cable configurations.

Insulation Length In Feet 2 4 6 8 10

No. Of Cable Turns Required Cable Length In Feet

1 3.3 7.3 11.3 15.3 19.3

2 5.8 13.8 21.8 29.8 37.8

3 8.7 20.7 32.7 44.7 56.7

4 12.1 28.1 44.1 60.1 76.1

5 16.0 36.0 56.0 76.0 96.0

6 23.4 47.4 71.4 95.4 119.4

OM-274540 Page 3

4. Determining Length of Starting Lead

1 Starting Lead

To determine the length of the

starting lead, subtract the required

cable length (from table in Section

3), from the length of the heating

cable being used, divide by 2, and

subtract 6 inches to account for the

hose bunching up while winding

the coil.

Example: A four foot long coil with

six turns requires 47.4 feet of ca-

ble. If a 50 foot cable is used to

wind this coil, the formula would be

(50−47.4)/2−.5 = .8 feet (9.6 in.) of

cable lead off of the insulation.

Ref. 274541-B

9.6 in.

(244 mm)

48 in. (1219mm)

24 in. (610mm)

. For the purpose of locating

the cable leads, cables are

measured from cable end to

cable end.

2 Excess Leads Off Insulation

NOTICE − Excess leads off of the

insulation should be

routed together to pre-

vent secondary mag-

netic fields, which re-

duce energy transfer to

the part being heated.

Miller PROHEAT INSULATION Owner's manual

Brand: Miller

Model: PROHEAT INSULATION

Type: Owner's manual

This manual is also suitable for

MG000000

Download PDF

report

in other languages

français: Miller PROHEAT INSULATION Le manuel du propriétaire

Miller PROHEAT INSULATION Owner's manual

This manual is also suitable for

Miller PROHEAT INSULATION Owner's manual

in other languages

Related papers