Strong SM-RBX-EXT-14-WH Owner's manual

Strong
Brand
Strong
Model
SM-RBX-EXT-14-WH
Type
Owner's manual

This manual is also suitable for

Pg. 1
www.snapav.com Support: 866.838.5052
SM-RBX-EXT-14 Installation Manual
Installation Manual
In-Wall VersaBoxSM-RBX-EXT-14-WH
Overview
Thank you for purchasing a great product from Strong™. We appreciate your purchase and
are committed to providing the highest quality products possible. The Strong In-Wall VersaBox
is designed to provide the best in-wall box solution for installers adding equipment behind low-
prole displays and other wall-mounted equipment. It can easily be installed in existing ceilings
and walls, or in new jobs using the optional SM-RBX-14-BKT Pre-Construction Bracket.
Inside the enclosure, up to two layers of components may be mounted using the built-in
attachment points and the pivoting center mounting plate. Easy-to-remove cutouts allow outlet
boxes and low-voltage rings to be installed in the sides of the box to save space for more
equipment. The center support plate is perforated to aid in wire management and device
mounting and can be set to different depths to allow for more varied installations. The plate
can also be modied as needed so that larger components t into the box.
Package Contents
(1) SM-RBX-EXT-14
(1) Center Support Plate
(1) Cover Plate
Important Instructions and Considerations for Installation
• Read and follow all instructions.
• Before beginning installation, carefully plan locations, accounting for potential electrical, ductwork, plumbing or other
obstacles that may interfere with installation of the box, equipment, or wiring.
• Contact a suitable contractor if you are unsure of how to best install.
Assembly Diagram
Note: To remove the cover with ease, pull the top two tabs loose rst and then the bottom. Do not bend the tabs.
Recommended for Installation
Tools
• #2 Phillips Screwdriver
• Drywall Saw
• Tape Measure
• Level
• ¼” Flat Head Screwdriver (optional)
• Electric Drill and ¼” bit (optional)
• Tin Snips (optional)
Optional Accessories and Hardware
• SM-RBX-14-BKT (pre-construction bracket for new work)
• Drywall screws (needed for use with SM-RBX-14-BKT)
• Electrical box and low voltage ring for adding terminations to cutouts
Use only standard size cover plates on boxes and rings installed
in the VersaBox. Midi and jumbo size plates will not t.
Adjustable Position
Center Support Plate
Single Gang Enclosure
Mounting on Top & Bottom
Optional New Work Pre-Construction Ring
(
SM-RBX-14-BKT, sold separately)
Pg. 2
www.snapav.com Support: 866.838.5052
SM-RBX-EXT-14 Installation Manual
Old Work Installation Instructions
1. Mark
the desired height of the top of the SM-RBX-
EXT-14 on the wall between two stud centers. Use a
stud finder to locate the stud locations.
2. Press the rear of the SM-RBX-EXT-14 to the wall, using a
level to line it up correctly. Mark the outline of the back
of the box as neatly as possible, and then set the box
aside.
3. Carefully cut the opening using a drywall saw.
4. After the hole is cut, test fit the box, and clean up the
opening as needed.
5. Remove the center support plate from the VersaBox. The
hinge clips may be left in place.
6. Insert the box into the opening. Using a #2 Phillips
screwdriver, secure the box to the drywall using the dog
legs on each side of the enclosure as illustrated.
Using Knockouts
The knockouts on the top and bottom of the VersaBox may
be used for installing low voltage rings or for outlet boxes. If
an outlet box is installed, it must be an old work, residential
grade box with integrated work supports to allow for secure
mounting.
When knocking out the opening, leave the small screw tabs
installed if a low voltage ring is being mounted, or remove
them to install an outlet box.
Modules
The back wall of the VersaBox has holes and knockouts
stamped into it on 6” centers to allow for easy structured can
module installation. Use a ¼” drill bit to open more of the
knockout stamps as needed to mount equipment.
Installing Equipment into the VersaBox
The center support plate allows for a variety of equipment conguration options. To accommodate equipment of different
thicknesses, the plate hinges can be reversed. The plate is also perforated so that it can be trimmed down in size, or
used for securing modules and wiring.
Experiment with the equipment configuration to determine the best installation method. For images of different
configurations of equipment installed in the VersaBox, see the VersaBox product page and Support Tab at
www.SnapAV.com.
Tighten
Dogleg
Screws with
#2 Phillips
Screwdriver
Cutout Dimensions
14" (W) x 13.25" (H)
Low Voltage/Outlet
Box
Cable Entry
Module
Attachment Holes
Note: If any of the 4 dog legs will not extend correctly due to stud clearance beside the box, a screw may be inserted
through the side of the box into the stud if one is close enough. Refer to the New Work Installation section earlier
in the manual for reference of where to insert the screw/s.
Pg. 3
www.snapav.com Support: 866.838.5052
SM-RBX-EXT-14 Installation Manual
Using the Center Support Plate
Changing the Center Support Plate Position
Attaching the VersaBox Cover
The center support allows for almost any mounting
conguration possible. If a network music player or other
larger equipment is being installed, the pre-stamped
square can be removed to make the full mounting depth
available. Additional sections may be trimmed out using
a pair of tin snips.
Dimensions in the illustration indicate the size of the
removable pre-stamped square.
1. Insert ¼” at head screwdriver into the slot at the rear
of the hinge clip and twist. Pry forward while pulling
to remove it.
2. Rotate the hinge clip 180°.
3. Press the hinge clip back in with the screwdriver until
it clicks into place.
4. Repeat for each of the 4 clips.
To attach the cover, knock out any additional wire pass-
throughs needed, and then slid the cover on, seating the
hooks on the right side rst, and pushing the left side in
until a “click” is heard.
Removable section
for adding Sonos
player
Perforations for
wire management
or attaching
equipment
6.48 in.
7.00 in.
A
B
C
Insert
hooks on
right side
first
Push in on
the opposite
side to close
Pg. 4
www.snapav.com Support: 866.838.5052
SM-RBX-EXT-14 Installation Manual
Dimensions
Enclosure
New Work Ring
13.25in.
14.50in.
14.00in.15.25in. 3.80in.
14.38in.
13.81in.
3.75in.
Double Layer
(Factory Position)
Single Layer
1.50in.
2.00in.
2.10in.
1.40in.
Center Support Plate
Position Dimensions
Warranty
Limited Lifetime Warranty
All Strong back-boxes and brackets have a Lifetime Limited Warranty. This warranty includes
parts and labor repairs on all components found to be defective in material or workmanship
under normal conditions of use. This warranty shall not apply to products which have been
abused, modied or disassembled. Products to be repaired under this warranty must be
returned to SnapAV or a designated service center with prior notication and an assigned return
authorization number (RA).
Lifetime
Contacting Technical Support
Phone: (866) 838-5052
Email: Techsupport@snapav.com
© 2013 Strong™
131004-1636
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Strong SM-RBX-EXT-14-WH Owner's manual

Strong
Brand
Strong
Model
SM-RBX-EXT-14-WH
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents