Frigidaire FGC26C3AUA Owner's manual

Brand: Frigidaire

Model: FGC26C3AUA

Category: Cookers

Type: Owner's manual

Gas

Cooktop

m-FRIGIDAIRE

Owner's

Guide

CONTENTS Page

VersiOnen espa_ol ..................................... 2

ProductRegistration ................................... 2

ImportantSafetyInstructions ................... 3-4

GroundingInstructions ............................... 4

Liquefied Petroleum(Propane)Gas

Conversion ................................................. 5

FlameSize.................................................. 5

Proper BurnerAdjustment .......................... 5

Setting SurfaceControl

Ventud(open) BurnerModels ............... 6

SealedBurner Models ........................... 6

Electric Ignition ..................................... 6

SetectingSurfaceCooking Utensils............. 7

SpecialtyPans& Trivets ............................. 7

CanningTips & information........................ 8

GeneralCleaning

CleaningVarious Partsof your Cooktop _. 9

Venturi (open) Burner Models ................ 10

SealedBurnerModels ........................ 11-14

Avoid ServiceChecklist............................. 15

Warranty................................................... 16

the LOOK of better performance

318200658 (0011) Rev. ,_

Product Registration

The PRODUCT REGISTRATION CARD

should be filled in completely, signed

and returned to Electrolux Home

Products North America.

Versibn en espahol

Sidesea obtener una copia enespaNol de

este Manual del Usuario, sirvaseescribir a

la direcciOn que seincluye a continuaciOn.

Solicite laP/N 318204005.

Spanish Ownerls Guides

Electrolux Home Products North America

Consumer Relations

P.O. Box212378

Augusta, Georgia

30917_2378

Thank you for choosing this appliance. The information contained within this

Owner's Guide will instruct you on how to properly operate and care for your

cooktop, Pleaseread through the information contained in your literature pack to

learn more about your new appliance.

Record Your Model and Serial Numbers

Recordin the space provided belowthe model andserialnumbers found underneath

or inside the cooktop,

Model Number:

Serial Number:

Date of Purchase:

This Owner's Guide contains general operating instructions for your cooktop and

feature information for severalmodels. Your cooktop may not have allthe described

features,

Note: Theinstructions appearing inthis Owner's Guide are not meant to cover every

possible condition and situation that may occur, Common senseand caution must

be practiced when installing, operating and maintaining any appliance.

O 2000 White Consolidated Industries

If the information in this manual is not

followed exactly, a fire or explosion may result causing

property damage, persona njury or death.

FOR YOUR SAFETY:

m Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Donottouchanyelectricalswitch; donotuseany phone

in your building.

• Immediately call your gas supplier from a neighbor's

° phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a qualified

installer, servicer or the gas supplier.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this appliance.

Save these instructions for future reference.

This guide contains important safety symbols and instructions. Pleasepay special attention to these symbols and follow all

instructions given, Here isa brief explanation of the use of these symbols,

This symbol will help alert you to situations that may cause serious bodily harm, death or property damage,

This symbol will help alert you to situations that

• Remove all tape and packaging wrap before using the

cooktop. Destroy the carton and plastic bags after unpacking

the cooktop. Never allow children to play with packaging material.

Do not remove the model/serial plate attached to the cooktop.

• Proper Installation--Be sure your appliance is properly

installed and grounded by a qualified technician inaccordance

with the National Fuel GasCode ANSI Z223.1 latest edition and

CAN/CGA B149.2, andthe National Electrical Code ANSI/NFPA

No. 70--latest edition, and local code requirements. Installand/

or adjust only per installation instructions provided in the literature

package for this cooktop.

may cause bodily injury or property damage,

• DO NOT TOUCH SURFACE BURNERS, GRATES, OR AREAS

NEARTHESE BURNERS. Surface burners may be hot even though

the flames are not visible. Areas near surface burners may become

hot enough to cause burns. During and after use, do not touch or

let clothing or other flammable materials touch these areas until

they have had sufficient time to cool, Among these areas are the

cooktop and the surfaces facing the cooktop.

• Wear Proper Apparel--Loose-fitting or hanging garments

should never be worn while using the appliance. Do not let

clothing or other flammable materials contact hot surfaces.

Ask your dealer to recommend a qualified technician and an

authorized repair service. Know how to shut off gas supply at the

meter and disconnect the electrical power to the cooktop at the circuit

breaker or fuse box in case of an emergency.

• User Servicing--Do not repair or replace any part of the

appliance unless specifically recommended in the manuals. All

other servicing should be done only by a qualified technidan. This

may reduce the risk of personal injury and damage to the cooktop.

• Never modify or alter the construction of a cooktop by

removing panels, wire covers, or any other part of the product.

Stepping or leaning on this cooktop can result

in serious injuries and may alsocause damage to the cooktop. Do

not allow children to climb or play around the cooktop.

• Storage on Appliance--Flammable materials should not be

stored on the cooktop, near surface burners. This includes

paper, plastic and cloth items, such ascookbooks, plasticware and

towels, aswell as flammable liquids. Do not store explosives, such

asaerosol cans, on the cooktop. Flammablematerials may explode

and result in fire or property damage.

Do not store items of interest to children in the

cabinets above the cooktop.

• Do not leave children alone--Children shoutd not beleft alone

or unattended in the area where an appliance is in use. They

should never beallowed to sit or stand on any part of the appliance.

Never use your appliance for warming or

heating the room.

• Do Not UseWater or Flour on Grease Fires--Smother the fire

with a pan lid,or use baking soda, a dry chemical or foam-type

extinguisher.

• When heating fat or grease, watch it closely. Fator grease may

catch fire if allowed to become too hot.

• UseOnlyDryPotholders--Moistordamppotholdersonhot

surfaces may result in burns from steam. Do not let the pot

holders touch the flame or burners. Do not use a towel or other

bulky cloth instead of a pot holder.

• Do Not Heat Unopened Food Containers--Buildup of pressure

may cause container to burst and result in injury.

• Knowwhich knobcontrols each surface burner. Alwaysturn the

knob to the LITEposition when igniting the burners. Visually check

that the burner has lit. Then adjust the flame so it does not extend

beyond the edge of the utensil.

Use Proper Flame SizemAdjust flame size so it

does not extend beyond the edge of the utensil. The use of

undersized utensils will expose aportion of the burner flame to direct

contact and may result in ignition of clothing. Proper relationship of

utensil to flame will also improve efficiency.

Do not use stove top grills on your sealed gas

burners. If you use a stove top grill on a sealed gas burner, it will

cause incomplete combustion and can result in exposure to carbon

monoxide levels above allowable current standards. This can be

hazardous to your health.

IMPORTANT SAFETY INSTRUCTIONS (continued)

• Use proper pan size--This appliance is equipped with one or

more surface burners of different sizes. Select utensils having fiat

bottom large enough to cover the surface burner. The use of

undersized utensils will expose a portion of the surface burner to

direct contact and may result in ignition of clothing. Proper

relationship of utensil to the surface burner will also improve

efficiency.

• Do Not Use Decorative Surface Burner Covers. If a burner is

accidentally turned on, the decorative cover will become hot and

possibly melt. You will not beable to seethat the burner ison. Burns

will occur if the hot covers are touched. Damage may aIso bedone

to the cooktop or burners because the covers may cause

overheating. Air will be blocked from the burner and cause

combustion problems.

• Utensil Handles Should Be Turned Inward and Not Extend

Over Adjacent Surface Burners--To reduce the risk of burns,

ignition of flammable materials, and spillage due to

unintentional contact with the utensil, the handle of the utensil

should be positioned so that it is turned inward, and does not

extend over adjacent surface burners.

• Never Leave Surface Burners Unattended at High Heat

Settings--Boilovers cause smoking and greasy spillovers that

may ignite, or a pan that has boiled dry may melt.

GLASS COOKTOPS (somemodels):

• Do Not Operate or Clean a Broken Cooktop Glass--If glasstop

should break, cleaning solutions and spillovers may penetrate the

broken cooktop and create a risk of electric shock. Contact a

qualified technician immediately.

Clean Cooktop Glass with Caution--If a wet sponge or cloth is

usedtowipe spillson ahot cooking area, becarefultoavoid a steam

burn. Some cleaners can produce harmful fumes if applied to a hot

surface.

• Protective Liners---Do not use aluminum foil to line surface

burner pans. Protective liners or aluminum foil may interfere with

heat and air distribution, and combustion. Damage to the

cooktop or personal injury may result.

• Glazed Cooking Utensils--Only certain types of glass, glass/

ceramic, ceramic, earthenware, or other glazed utensils are

suitable for cooktop service without breaking due to the sudden

change in temperature. Check the manufacturer's

recommendations for cooktop use.

• Do Not Place Hot Cookware on the Cooktop Glass. This could

cause glass to break.

• Avoid scratching the cooktop glass with sharp objects.

SAVE THESE INSTRUCTIONS

Grounding Instructions (electric ignition models only)

IMPORTANT: READAN DSAVE THESEINSTRUCTIONS.

Thisappliance isequipped with a 3 prong grounding plug for your

protection against shock hazard and should be plugged directly into a properly

grounded receptacle. DO NOT cut or remove the grounding prong from this plug.

Forpersonal safety,this cooktop must be properly grou nded. Formaxim umsafety,

the power cord must be plugged into a 120V--60 Hz. outlet that is correctly

polarized and properly grounded.

If a two-prong wall receptacle is the only available outlet, it is the personal

responsibility of the consumer to have it replaced with a properly grounded three-

prong wall receptacle installed by a qualified electrician.

DO NOT UNDERANY CIRCUMSTANCES CUT OR REMOVE THE THIRD ROUND

GROUNDING PRONGFROM THE POWERCORD PLUG, SEETHE INSTALLATION

INSTRUCTIONSPACKAGEDWITH THISCOOKTOPFORCOMPLETEINSTALLATION

AND GROUNDING INSTRUCTIONS,DO NOT OPERATETHECOOKTOP USING A

TWO-PRONG ADAPTERORAN EXTENSIONCORD,

Avoid fire hazard or

electrical shock. Do not use an adaptor

plug, an extension cord, or remove

grounding prong from electrical power

cord. Failure to follow this warning can

cause serious injury, fire or death.

Groundino

gpe wa

receD[acle

3o not under any

clrcums[ances cut

remove, or Dypass

the grounding prong

Power suppg cord w_t_

3-prong grounding plug

Liquefied Petroleum (Propane) Gas Conversion

Severe shock or damage to the cooktop may occur if the cooktop is not installed by a qualified installer or

electrician.

This appliance can be used with Natural Gas and Propane Gas.It isshipped from the factory for use with natural gas.

If you wish to convert your cooktop for use with Liquefied Petroleum (propane) gas:

- Models with Venturi (open} Burners. seethe installation instructions guide for the conversion instructions.

- Models with Sealed Burners:

- Forsome of them, you should order the conversion kit from your local dealer or from an authorized serviceagency (see

Warranty). Seethe installation instructions for the conversion kit number.

- F_r_thers,thec_nversi_nkitisinc_udedinthepackaging,ify_uwisht_c_nverty_urc__kt_p__rusewithpr_panegas_

usethe supplied fixed orifices located in the package containing the installation instruction, in a bag marked "FORLP/

PROPANEGASCONVERSION". Follow the instructions packaged with the orifices (for models with sealed burners only).

Theconversion must beperformed bya qualified servicetechnician in accordance with the manufacturer's instructions and all codes

and requirements of the authority having jurisdiction. Failure to follow the instructions could result in serious injury or property

damage. The qualified agency performing this work assumes responsibility for the conversion.

Flame Size

For most cooking, start on the highest control setting and then turn to a lower one to

complete the process. Usethe chart below as a guide for determining proper flame size for

various types of cooking. The size and type of utensil used and the amount of food being

cooked will influence the setting needed for cooking.

For deep fat frying, use a thermometer and adjust the surface control knob accordingly. If

the fat istoo cool, the food will absorb the fat and be greasy.If the fat istoo hot, the food will

brown so quickly that the center will be undercooked. Do not attempt to deep fat fry too

much food at once asthe food will neither brown nor cook properly.

*Flame size

High Flame

Medium Flame

Low Flame

Type of Cooking

Start most foods; bring water to a boil; pan broiling.

Maintain a slow boil; thicken sauces, gravies; steam.

Keep foods cooking; poach; stew.

* These settings are based on using medium-weight aluminum pans with lids. Settings

may vary when using other types of pans.

Never extend the flame

beyond the outer edge of the

utensil. A higher flame simply

wastes heat and energy, and

increases your risk of being

burned by the flame.

IGHT:;

Proper Burner AdJustments

Thecolor of the flame isthe keyto proper burner adjustment. A good flame isclear, blue and hardly visible in a well-lighted room.

Eachcone of flame should be steady and sharply defined. Adjust or clean burner if flame isyellow-orange. To clean burner, see

instructions underGeneral Cleaning.

Setting Surface Controls

The surfacecontrol knobs shown below

maynot look identicalto the SurfaceCon-

trois Knobson your range;They are only

representational.

Venturi (opened) Burner Models

To AdJust Low or "Simmer" Setting (some models)

The burner flame, at low setting, can be adjusted if it istoo high or too low; refer to

the installation instruction for adjustment procedure,

To Adjust Standing Pilot Model (some models)

Eachburner lights automatically either an electric or a standing pilot, depending

on your model. Standing pilots must be lit initially. ]o light the standing pilot, open

gas supply on pilot shutoff valves (screw), lift the cooktop from the front edge and

hold a match near the pilot. Standing pilots will remain lit when the burners are

turned off; because of that, the porcelain enamel cooktop can be hot even if

burners are not used; refer to Installation Instructions for proper pilot adjustment.

Models with electric ignitors light automatically each time acontrol knob isturned

to the LITEposition.

To operate the Surface Burner:

1, Placecooking utensil on burner.

2, Pushin and turn the Surface Control knob to LITE,Note: All electronic ignitors

will clickat the sametime. However, onlythe burneryou areturning on will ignite,

3, Visually check that the burner haslit,

4, After the burner lights, turn the control knob tothe desired flame size.Thecontrol

knobs do not have to be set at aparticular mark, Use the guides and adjust the

flame asneeded, DO NOT cook with the control knob in the LITEposition, (The

electronic ignitor will continue to click if left in the LITEposition,)

Sealed Burner Models

Your appliance may be equipped with any combination of the following burners:

Simmer Burner, this burner is best used for simmering delicate sauces, etc.

Standard Burner, can be used for most all surface cooking needs,

Large Burner, the larger burner is best used when bringing large quantities of liquid to temperature and when preparing larger

quantities of food,

Regard_ess_fsize_a_waysse_ecta_tensi_thatissuitab_ef_rtheam_untandtype_ff__dbeing The surface control knobs

prepared, Selecta burner and flame sizeappropriate to the pan. Never allow flames to extend shownbelowmaynotlook iden-

beyond the outer edge of the pan, tical to the Surface Controls

Eachburner lights automatically from an electric ignitor each time a control knob isturned to Knobson your range; Theyare

the lite position, only representational.

To operate the surface burner:

1, Placecooking utensil on burner.

2, Push in and turn the Surface Control knob to LITE,Note: All electronic ignitors will click

atthe same time. However, only the burner you are turning on will ignite.

3, Visually check that the burner haslit,

4, After the burner lights, turn the control knob to the desired flame size. Thecontrol knobs

do not have to be set at a particular mark. Usethe guides and adjust the flame asneeded.

DO NOTcook with the control knob inthe LITEposition. (Theelectronic ignitor will continue

to click if left in the LITEposition.)

5, To turn the burner off, turn the control knob asfar asit ill go, to the OFFposition.

Electric Ignition Models

Inthe event of an electrical power outage, the surface burners can be lit manually. To light a surface burner, hold a lit match to

the burner head, then slowly turn the surface control knob to LITE.Usecaution when lighting surface burners manually,

Surface burner in usewhen an electrical power failure occurs will continue to operate normally.

Do not operate the burner for an extended period of time without cookware on the grate, Thefinish on

the grate may chip without cookware to absorb the heat.

Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on top

of the cooktop when it is in use. Theseitems could melt or ignite. Pot holders, towels or wood spoons could catch fire if placed

too close to a flame. 6

Selecting Surface Cooking Utensils

For best results and energy conservation, choose cooking utensils that have these characteristics:

Pansshould havefiat bottoms. Check for

flatness by rotating aruler acrossthe bot-

tom. There should be no gaps between

the pan and ruler.

Note: Always usea utensil for itsintend-

ed purpose. Follow manufacturer's in-

structions, Some utensils were not made

to be used in the oven or on the cooktop.

Note: Do not usegriddle over more than

one burner, That can damage your

cooktop and that can result in exposure

to carbon monoxide levels above allow-

able current standards. That can hazard-

ous to your health.

Specialty Pans & Trivets

*GOOD

7ii_:i'ii',!!_i_!_ii_i_ii,_iiiii_!_i_:_i_ii_i_i :_:_i_ii!!i_i':!i'il"_

• Flat bottom and straight sides.

• Tightfitting lids.

• Weight of handle does not tilt

pan. Pan is well balanced.

• Pansizes match the amount of

food to be prepared.

• Made of material that conducts

heat well.

• Easyto clean.

POOR

• Curved and warped pan bottoms.

I; l U

• Pan overhangs unit by more than

2.5 cm (1 "),

• Heavy handle tilts pan,

• Flame extends beyond unit,

* Specialty pans such as lobster pots, griddles and pressure cookers may be used

but must conform to the above recommended cookware requirements.

Woks with fiat bottoms suitable for

use on your cooktop are available in

most cookshop or hardware stores,

Round-bottomed woks (with a

support ring that does not extend

beyond the burner unit) may also be

used. The metal ring was designed to

support the wok safely when it is

filled with large amounts of liquids

(soup making) or fat (flying),

DO NOT use a wok if it is equipped

with a metal ring that extends

beyond the burner unit. Because this

ring traps heat, the surface unit and

cooktop surface could be damaged.

Wire trivets: Do not usewire trivets. Cookware bottoms must be in direct contact

with the grates.

DO NOT use two burner units to heat one large pan such as a

roaster or griddle, or allow cooking utensils to boil dry. The bottom surface of the

pan in either of these situations could causediscoloring or crazing of the appliance

cooking surface, and damage to the grates and burner units.

Canning Tips &

Information

Canning can generate

large amounts of steam. Useextreme cau-

tion to prevent burns. Always raise the

lid to vent steam away from you.

1, Usetested recipes and follow instructions carefully, Check with your local

Cooperative Agricultural Extension Service or a manufacturer of glassjars for

the latest canning information.

2, Useflat-bottomed canners only. Heat is spread more evenly when the

bottom surface isflat,

3, Center canner on the burner grate.

4, Start with hot water and a high heat setting to reduce the time it takes to

bring the water to a boil; then reduce the heat setting aslow as possible to

maintain a constant boil.

5, It isbest to can small amounts and light loads,

Prevent damage to cooktop and burner grates:

1. Do not use water bath or pressure canners that extend more than one inch

beyond the edge of the burner grate.

2. Do not leave water bath or pressure canners on high heat for an extended

amount of time,

3. Alternate surface units between each batch to allow the units and

surrounding surfaces to cool down, Tryto avoid canning on the same burner

unit all day.

Safecanning requires that harmful micro-organisms are destroyed

and thejars aresealed completely. When canning in a water bath canner, a gentle

but steady boil must be maintained continuously for the required time,

General Cleaning

Cleaning Various Parts of Your Cooktop

Before cleaning any part of the cooktop, be sure all controls are turned OFFand the cooktop is COOL, Remove spillovers and

heavy soiling as soon as possible. Regular cleaning will reduce the number of major cleaning later

Surfaces How to Clean

Aluminum (]rim Pieces)& Use hot, soapy water and a cloth. Dry with a clean cloth.

Vinyl

Glass, Painted and Plastic Forgeneral cleaning, use hot soapy water and a cloth, For more difficult soils and built-up

Control Knobs, Body grease, apply a liquid detergent directly onto the soil. Leaveon soil for 30 to 60 minutes,

Pieces, and Decorative Trim Rinsewith a damp cloth and dry, DO NOT useabrasive cleaners on any of these materials;

they can scratch,

Control Panel

Stainless Steel, Chrome

Decorative Trim

Porcelain Enamel

Burner Grates, Burner Pans

(some models), Burner Rings

(some models), Cooktop

Surface

Surface Burners

Before cleaning the controlpanel, turn all controls to OFFand remove the control knobs, ]o

remove, pull each knob straight off the shaft, Clean using hot, soapywater and acloth. Be

sure to squeeze excess water from the cloth before wiping the panel; especially when

wiping around the controls. Excesswater in or around the controls may cause damage to

the appliance. ]o replace knobs after cleaning, line up the flat sides of both the knob and

the shaft; then push the knob into place,

Gentle scouring with a soapy nylon pad will remove most spots. Rinsewith a 1:1 solution of

clean water and ammonia, Cover difficult spots with an ammonia soaked paper towel for

30 minutes, scrub with a nylon pad and rinse with clean water Cleaners made especiallyfor

stainless steel or chrome are recommended. Bluish stains on these materials are caused by

overheating and cannot be removed, Remove all cleaners or the finish may be damaged

during future heating, DO NOT usespray oven cleaners on the cooktop.

Clean burner grates in the dishwasher and dry upon removal, If soils are not removed,

follow the cooktop cleaning instructions below.

Gentle scouring with a soapy nylon pad will remove most spots, Rinsewith a 1:1 solution of

clean water and ammonia, If necessary, cover difficult spots with an ammonia-soaked

paper towel for 30 to 40 minutes. Rinsewith clean water and damp cloth, then scrub with

a soap-filled scoring pad, Rinseand wipe dry with a clean cloth. Remove all cleanersor the

_orcelain may become damaged during future heating. DO NOT use spray oven cleaners

on the cooktop,

The holes in the burners of your cooktop must be kept clean at all times for proper ignition

and acomplete, even flame. Clean the burner holes routinely with a small gauge wire or

needle and especially after bad spillovers which could clog these holes,

]o remove and replace burner units per your model, see instructions under General

Cleaning. Toclean, soak the burners in a 1:1 solution of ammonia and water for 30 to 40

minutes. For stubborn stains, scrub with soap and water or a mild abrasive cleanser and

damp cloth. Dry the burners thoroughly in a warm oven for 30 minutes. Then replace them,

making sure they are seated and level. DO NOT wash burner units in the dishwasher.

General Cleaning (continued)

Venturi (open) Burner Models (somemodels)

To Raise and Lower the Top for Cleaning

The cooktop ishinged and can be raisedto clean the areaunderneath. Besure all cooktop controls are turned to OFFand burner

grates are cool.

1. Removecontrols knobs, burner grates and spillover bowls. Set aside.

2. Grasp the front of the cooktop and lift. Some models have a swing-up rod to support the cooktop in its raised position.

3. Clean under the cooktop.

4. Lower the top gently after lowering the support rod (some models).

5. Replace bowls, grates and control knobs.

When lowering the top, grasp the sideswith fingertips only, Be careful not to pinch fingers, Also, DO NOT drop

or bend the cooktop when raising or lowering. This could damage the surface.

DO NOT turn on the burners when the cooktop israised for cleaning. Besure that the top iscompletely lowered

and securely in place before turning on the burners,

To Remove and Replace Burners

The burners on your cooktop maybe removed for cleaning. Be sure all controls are turned to OFFand burner grates are cool

before removing cooktop burner units,

To Remove Burners

1. Removethe shipping screws from the support bracket. Seeillustrations for location of

screws.

2, Grasp the burner head and tilt it to the right to releasethe tab from the burner support

(A in Figure 1).

3, Lift the end of the burner assembly, Then pull away from the front of the cooktop to

free the air shutter from the gas valve orifice (Bin Figure 1).

If your cooktop isequipped with a standing gas pilot, usecaution when removing burner.

The flash tube may be hot because it is located near the pilot.

Check the lighter and burner ports (Figure 2). If they areclogged, usea wire or needle to

clear them,

Figure I

Gas Valve

Burner Orifice _

Support f,, \_j>_

]O remove burned-on food, soak the burners in a vinegar and water solution for

20-30 minutes. Forstubborn stains, scrub with soap and water or a mild abrasive cleanser

and adamp cloth, Do not wash burners in a dishwasher,

To Replace Burners

1. Slide the air shutter over the gas valve orifice (Figure 1).

2. Lower the burner assembly and hook the tab in the slots in the burner support. Make

sure it isproperly seated and level.

3. Be sure both tabs are in the correct slots, the burner sits level and straight, and the

flash tube forms a straight line from the igniter to the burner (Figure 2).

4. Replace shipping screws if desired. Thesescrews are not necessary for the operation

of the burnen They stabilize the burner during shipping of the appliance. Retain the

screws for later use in the event the range is moved.

Figure 2

Ughter Fort

Burner Support Igniter

r-"" .ral Cleaning (continued)

d Burner Models (somemodels)

Unlike the standard gas range, THIS COOKTOP ISNOT REMOVABLE. Do not attempt to remove or lift the cooktop,

Before cleaning the cooktop, be sure the controls are turned to OFF and the cooktop isCOOL.

DO NOT use a cooktop cleaner on a hot cooktop. The fumes can be hazardous to your health, and can

chemically damage the ceramic- glass surface. Be sure the controls are turned to OFF. Do not use commercial oven

cleaners on any part of the cooktop. Damage to the finish or parts could result.

To Clean the Tempered-glass Cooktop (some models)

Thecooktop isdesigned to make cleaning easier, Becausethe four burners are sealed,cleanups are

easywhen spillovers are cleaned up immediately. To clean, wipe with a clean, damp cloth and wipe

dry.

Correct and consistent cleaning isessential to maintaining your heabresistant glasstop. Spills and

spatters should be wiped up using a clean paper towel and sudsy water. This should be done either

assoon as possible after spill occurs, after cooking is completed, or at the latest, before using the

cooktop again. Usecaution if the cooktop ishot. Forheavy spills, spatter or burned=on materials, use

razor blade scraper. Hold the razor blade scraper at a 30° angle and remove food spillsor burned on

food residue.

Forsugary spillovers:

Sugaryspills can cause pitting of your cooktop surface. Therefore, you must begin cleaning the spills

while the cooktop isstill hot.

Finish the cleaning process by applying a recommended heat- resistant glass cooktop cleaning

cream. Apply cleaner with clean, damp paper towel. Rinsewith a paper towel dampened with clean

water and wipe dry. Always wipe the cooktop thoroughly to avoid heating any cleaner residue,

bu rne d_0n

witharazorbladescraper.Use

cautionto avoiddamaging

surface.

Do NOT use the following on the heat-resistant glass cooktop:

Abrasive plastic, nylon, metal scouring or cloth pads, They may scratch the cooktop and make it more difficult to clean later.

Always use a new, clean paper towel when cleaning the heabresistant glass top.

Anything that may melt (plastics, aluminum foil, sugar or food with a high sugar content).

Heavyduty cleansers, rust or stain removers.

Chlorine bleach, ammonia, hydrofluoric acid or any other kind of chemical cleaners. They may etch or discolor the cooktop.

Sponges, cloths ordish towels. Always usea new, clean paper towel when cleaning the cooktop. Lint or soil remaining on the

cooktop from a cloth or sponge can burn and cause discoloration.

To Clean the Ceramic-glass Cooktop (some models)

The cooktop is designed to make cleaning easier. Cleanups are easy when spillovers are

cleaned up immediately. To clean, wipe with a clean, damp cloth and wipe dry,

Correct and consistent cleaning isessential to maintaining your heabresistant glass top. Spills

and spatters should be wiped up using a clean paper towel and sudsy water. This should be

done either as soon as possible after the spill occurs, after cooking iscompleted, or at the latest,

before using the cooktop again. Use caution if the cooktop is hot. For heavy spills, spatter or

burned-on materials, use a razor blade scraper. Hold the razor blade scraper at a 30° angle and

remove food spills or burned on food residue.

For sugary spillovers:

Sugaryspills can cause pitting of your cooktop surface. Therefore, you must begin cleaning the spills

while the cooktop isstill hot.

Finish the cleaning process by applying a recommended heat-resistant glass cooktop cleaning

cream, Apply cleaner with clean, damp paper towel. Rinse with a paper towel dampened with

clean water and wipe dry. Always wipe the cooktop thoroughly to avoid heating any cleaner

residue.

bUrned On

witharazorbladescraper.Use

cautionto avoiddamaging

surface,

General Cleaning (continued)

Se= ed Burner Models (somemodels)(continued)

To ( ean the Ceramic-glass Cooktop (somemodels)(continued)

Sp_ ial Caution for Aluminum Foil and Aluminum Cooking Utensils

1) # ,minumfoil

L ._of aluminum foil will damage the cooktop. Do not use under any circumstances.

2) A iminumutensils

T ._melting point of aluminum being much lower than that of other metals, care must be taken when aluminum pots or pans

a used. If allowed to boil dry, not only will the utensil be ruined, but also permanent damage in the form of breakage, fusing

o _narkingmay affect the ceramic glass surface.

Thil [Is to Remember

1, [ not slide utensils across cooktop surface in any circumstance, doing somay scratch or

n _talmark the cooktop surface.

2. _ _id using bleach and do not useammonia to clean the ceramic surface.

3, E not put plastic items on warm cooking areas, m i

4, Never slide oven racks across cooktop surface, They may scratch or metalmark the cooktop.

5, If cooktop should break, do not usecooktop or attempt to clean it, Call your SearsService Center immediately.

6, Never use rivet or metal stand between the cooking utensil and the ceramic cooktop, The ceramic surface may be

scratched, metal marked or etched by such items.

7, Sugary spills can cause pitting of your cooktop surface, Therefore, you must begin cleaning the spills while the cooktop is

still hot, Usecaution when following the steps below.

a) Turn off all surface units and remove all pans immediately,

b) Wearing an oven mitt, usea razor to scrape the hot spill out of the cooking zone to cooler area on the cooktop,

c) Allow the cooktop to cool,

Use and Care of Glass Surface

Problem Cause To Remove

Fine "brown

lines" (tiny

scratches or

abrasions which

have collected

soil)

Coarse particles (salt,

sand, sugar or grit)

between bottom of

cookware and cooktop

that are not removed

before cooking.

Using incorrect cleaning

materials.

To Prevent

Clean cooktop after

every use.

Tiny scratches are not removable.

They can be minimized by

continual use of cleaner creme.

Such scratches do not affect

cooking.

Daily use of cleaner

creme.

Metal marking Sliding or scraping Do not slide cookware Apply cleaner creme

(mark or black metal utensils or oven across cooktop, with dampened paper

marks), shelves across cooktop, towel to a cooled surface.

Brown streaks Cleaning with a Use cleaner creme Use a small amount of cleaner

and specks, sponge or dishcloth with clean, damp paper creme with clean, damp paper

that has been used towel, towel.

for other kitchen tasks.

NOTE: Due to the high intensity of heat generated by the surface elements, the glass surface will turn green when the element

will be turned off. This phenomenon is normal and the glass will come back to its original white color after it has completely

cooled down, (White glass cooktops only).

General Cleaning (continued)

Sealed Burner Models (somemodels)(continued)

To Clean the Ceramic-glass Cooktop (somemodels)(continued)

Use and Care of Glass Surface (continued)

Cleaning Materials for Ceramic-Glass Cooktop

Some cleaning materials may contain an ingredient which can damage the cooktop. Userecommended cleaning products only

(seebelow). Cleaner cream should be used regularly. First use recommended products listed below, then use cleaner cream.

Useonly recommended cleaning products and Follow these basic cleaning suggestions.

1. Before the cooktop is used, thoroughly clean and saturate the cooktop with cleaner cream.

a) Dampen clean paper towel and clean unit.

b) Wipe off with another clean, damp paper towel; then wipe dry.

2. For normal daily cleaning, apply a dab of cleaner cream in the center of each unit-area to be cleaned. Start with

approximately 1/8 teaspoon (apply more if needed). Then, proceed as stated above in a and b.

3. Make sure bottom of cookware and cooking area are clean and dry.

4. Select heat settings and cookware large enough for Food and liquid.

5. Wipe up food spills and spatters before they burn into surface,

IMPORTANT: Regularly use cleaner cream. If you run out of cream, use one of the cleaners listed, Be sure to get anew supply

of cleaner cream,

Never mix cleaning products! Mixtures may interact, with damaging or hazardous results.

Do Use on Ceramic GlassCooktop

1, Baking soda.

2. Non-impregnated plastic and nylon pads.

3. For burned on material, scrape with single-edged razor blade, held at a 30° angle.

4. Ceramic glass cleaning cream.

Do not use on ceramic-glass cooktop

1, Avoid pads, that can leave marks and scratches,

2, Avoid heavy-duty cleaning powders; these can scratch, depending on their abrasiveness and cleaning pressure applied,

3, Avoid chemical oven cleaners, These can etch the cooktop surface and are caustic,

4, Avoid rust stain removers containing hydrofluoric acid.

5, Avoid using bleach and do not use ammonia.

Special Cleaning Instructions for Mineral Deposits and Discolorations

Problem: A gray brown stain that is not removed when using cleaner creme,

Cause: Condensation, when cooking, often collects and drips from cookware, The minerals Found in water supply and Foodsmay

causea gray or brown film to develop on cooktop, ThisFilmissothin it cannot be felt and appearsto be under cooktop.

To Prevent: Daily and proper use of cleaner creme.

To Remove: - Wet surface with water and sprinkle on cleaner creme.

- Scrub with clean, damp paper towel until stain disappears,

- Clean remaining paste away with damp paper towel.

- Apply dab of cleaner creme and polish with a clean paper towel,

WARNING

=Do not usecleansers on a heated surface. Fumescould be hazardous. Wait for area to cool before cleaning,

- Do not use cleaner creme to clean porcelain, paint or aluminium,

General Cleaning (continued)

Sealed Burner Models (somemodels)(continued)

To Clean the Burner Grates, Contoured Burner Pans, Burner Cap and Burner Base

Theburner grates, contoured burner pans, burner capsand burner baseshould beroutinely cleaned. Keeping the burner ports clean

will prevent improper ignition and an uneven flame. Seeinstructions below,

To Clean the Burner Grates

Be sure burners and grates are cool before you place your hand, a pot holder,

cleaning cloths orother material on them. Thecastiron burnergrates canbe washed

in hot soapywater. Rinsethoroughlyand drythe grates with acloth- don't putthem

on the cooktop while still wet, Besure the grates are positioned securely over the

burners.

To remove burned on food, place the grates in a covered container or plastic bag.

Add 1/4 cup ammonia and soak for 30 minutes, Wash, rinse well and dry. An

abrasive cleaner can be used for stubborn stains.

meacuteeee<>

To Clean the Contoured Burner Pans

The burner pans are attached to the cooktop and are not removable, The burner pan forms a recessedwell area located around

each burner unit. If spill occurs in one of the well areas,blot up spill with an absorbent cloth, Rinsewith a clean, damp cloth and

wipe dry,

Burner Cap

Sealed Burner

To Clean the Burner Cap

Remove burner cap, Usesoap-filled pad or mild abrasive cleanser to clean burner

caps, If necessary,cover stubborn spots with an ammonia=soaked paper towel for

30 minutes. Rubgently with a mixture of clean water and vinegar, Wipe dry. Remove

all cleaners or the porcelain may become damaged during future heating.

To Clean the Removable Burner Baseand Gas Opening (some models)

The ports (or slots)around the burner basemust be routinely cleaned. Usea small-

gauge wire or needle to clean small slots or holes,

Note: Ifthe electrode isdamaged orbroken, the surface burner will not light because

it will not spark. Manual lighting with a match isstill possible.

For proper flow of gas and ignition of the burner - DO NOTALLOW SPILLS,FOOD,

CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTERTHE GAS OPENING

TUBE.Gasmustflow freelythrough the small hole in the brassorifice for the burners

to light properly, If the gasopening orifice becomes soiled or clogged, usea small-

gauge or needleto clean. ALWAYS keepthe burner capin place whenever a surface

burner isin use,

To Replace the Burner Base and the Burner Cap

Make sure the pieces are thoroughly dry before placing back.

1. Replace burner baseand burner cap at there place. Make sure each burner cap

and burner base are properly aligned and leveled.

2. Replace the burner grate.

3. Turn the burner on to determine if it light. If the burner does not light after

cleaning, contact an authorized servicer. Do not service the sealed burner

yourself.

Avoid Service Checklist

Beforeyou call for service, review this list, It may saveyou time and expense, The list includes common occurrences that are not

the result of defective workmanship or materials in this appliance.

OCCURRENCE POSSIBLE CAUSE/SOLUTION

Surface burners do not light. Surface Control knob has not been completely turned to LITE,Pushin and turn the

Surface Control knob to LITEuntil burner ignites and then turn control to desired

flame size,

Be sure gas supply valve is open,

Gas-air mixture needs a straight line to travel. Besure burner isproperly seated in its

support (models with open burners only),

Burner ports or slots are clogged. With the burner off, use a small-gauge wire or

needle to clean ports or slots.

Power cord is disconnected from outlet (electric ignition models), Be sure cord is

plugged securely into outlet,

Electrical power outage (electric ignition models), Burners can be lit manually, See

Setting Surface Controls in this Owner's Guide,

Surface burner flame burns half way

around.

Burner ports or slots are clogged, With the burner off, clean ports with a small-

gauge wire or needle to clean ports or slots.

Moisture ispresent after cleaning, Lightlyfan the flame and allow burner to operate

until flame isfull. Drythe burners thoroughly following instructions under General

Cleaning.

Surface burner flame isorange. Dust particles in main line, Allow the burner to operate a few minutes until flame

turns blue,

In coastal areas, a slightly orange flame is unavoidable due to salt air,

Scratches or abrasion on cooktop

surface.

Coarse particles such as salt or sand between cooktop and utensil can cause

scratches. Besure cooktop surface and bottoms of utensils are clean before usage.

Small scratches do no affect cooking and will become lessvisible with time.

Cleaning materials not recommended for ceramic-glass cooktop have been used.

See "To Clean the Ceramic-glass Cooktop" section under General Cleaning.

Cookware with rough bottom hasbeen used. Usesmooth, fit=bottomed cookware.

Metalmarks.

Sliding or scraping of metal utensils on cooktop surface. Do not slide metal utensils

on cooktop surface. Useceramic-glasscooktop cleaning cream to remove the marks.

See "To Clean the Ceramic-glass Cooktop" section under General Cleaning.

Brown streaks or specks. Boilover are cooked onto surface. Userazor blade scraper to remove soil. See "]o

Clean the Ceramic=glass Cooktop" section under General Cleaning.

Areas of discoloration with metallic

sheen.

Mineral deposits from water and food. Remove using a ceramic-glass cooktop

cleaning cream, Use cookware with clean, dry bottoms,

COOKTOP WARRANTY

Your cooktop is protected by this warranty

FULLONE-YEAR

WARRANTY

UMITED 2_-5 TM

YEAR WARRANTY

(Glass Srnoothtop,

Seal & Elements)

UMITED

WARRANTY

(Applicable to the

State of Alaska)

WARRANTY

PERIOD

One year from original

purchase,date

Sec_ld through firth

years from original

puEchasedate

THROUGH OUR AUTHORIZED SERVICERS,

WE WILL:

THE CONSUMER WILL BE RESPONSIBLEFOR:

Costs of seF4ce calls that a_e listed under NORMAL

RESPONSIBIUTIES OF THE CONSUMER, *

DiagnostJcand any transportation and labor cost_ which am

required because of s@vice

Pdy all costs for Eepaidng or replacing any parts d this

appliance which prove to be defective in materials or

workmanship

Provide a _eplacement for any defective surface heating

element, deteriorated rubberized silicone seal(upswept

models c4]ly),or glass slnooth[op that clacks due to

thermal breakage (not customer abide).

All of the provisions of the full and limited warranties

above and the exclusions listc_dbelow apply

Time periods listed Costs of the technician's t_avelto the home and any costs for pick

above up and ddivery of the appliance required because of s@vice

In the U.S.A., your appliance iswarranted by Eiectrolux Home Products North America, a division of White Consolidated Industries, Inc, We authorize no

person to change or add to any of our obligations under this warranty. Our obligations For service and parts under this warranty must be performed by

us or an authorized Electrolux Home Products North America servicer. In Canada, your appliance is warranted by WCI Canada, inc.

*NORMAL

RESPONSIBILITIES

OF THE CONSUMER

EXCLUSIONS

IF YOU NEED

SERVICE

This warranty applies only to products in ordinary household use, and the consumer is responsible for the

items listed below:

1. Proper use of the appliance in accordance with instructions provided with the product,

2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in

accordance with all local plumbing, electrical and/or gas codes.

3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose

connections or defects in house wiring,

4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,etc.,

which are not a part of the appliance when it was shipped from the factory.

5. Damages to finish after installation,

6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).

This warranty does not cover the following:

1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTYDAMAGE AND INCIDENTAL EXPENSES

RESUEfING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.

NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation

or exclusion may not apply to you,

2. Service calls which do not involve malfunction or defects in workmanship or material or for appliances not in ordinary

household use. The consumer shall pay for such service calls.

3. Damages caused by services performed by servicers other than Electrolux Home Products North America or its

authorized servicers; use of parts other than genuine Electrolux Home Products parts; obtained from persons other

than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.

4. Products with original serial numbers that have been removed or altered and cannot be readily determined.

Keep your bill of sale, delivery slipr or some other appropriate payment record. The date on the bill establishes the

warranty period shoutd service be required, If service is performed, it is in your best interest to obtain and keep all receipts,

This written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service

under this warranty must be obtained by contacting Electrolux Home Products:

USA

1°800°944°9044

Electrolux Home Products

North America

RO. Box 212378

Augusta, GA 30917

Canada

1°866,213*9397

Electrolux Home Products

North America

802, boul. L'Ange-Gardien

L'Assomption, Quebec

J5W 1T6

This warranty only applies in the 50 states of the U.S.A., Puerto Rico, and

Canada, Product features or specifications as described or illustrated

are subject to change without notice. All warranties are made by

Electrolux Home Products North America, adivision of White Consolidated

Industries, Inc, In Canada, your appliance is warranted by WCI Canada,

Inc,

Frigidaire FGC26C3AUA Owner's manual

Brand: Frigidaire

Model: FGC26C3AUA

Category: Cookers

Type: Owner's manual

Download PDF

report

Frigidaire FGC26C3AUA Owner's manual

Frigidaire FGC26C3AUA Owner's manual

Related papers

Other documents