Gyros S32 Using Instructions

Brand: Gyros

Model: S32

Type: Using Instructions

In this instruction of material, the specification or parts within the accessories bag is for

reference only. The company will not be responsible for any change of printed part and

notify the consumers. Any update or change please refer to the website of SYMA

(www.symatoys.com).

REMOTE CONTROL HELICOPTER

Low-voltage protection: When the helicopter battery is low, the helicopter control system

battery will be protected, and stop the supply of helicopter rotor; low power protection,

the need to charge to secure a new flight of the helicopter.

Overcurrent protection: When the helicopter blades in the rotating state by collision or

jammed, the helicopter circuit overcurrent protection.

1. Please recheck the ground, keep away from the crowds, animals and other barriers.

2. Turn the remote control on, after a while, the LEDs will be flashing. Push the motive handle must

be pushed to the maximum control route of travel first, then adjust it to the lowest; When the

remote control LEDs keep lighting, it means the helicopter is going to fly.

3.Open remote control power switch, then the remote status light was flashing and accompanied by

the rhythmic sound, and then push up the up / down variable speed joystick to the top, then its

back to the most low-end; the status of the remote controlThe indicator is lit and the sound stopped,

the remote control to enter the preparatory off state.

4. Push the motive handle slowly, then the helicopter will fly up.

Charging time: can be 60~90 minutes flying about 6 minutes!

电池

First turn off the power switch of the helicopter, "USB cable charging plug to the charging port is

connected to the helicopter, and then" USB cable " The USB end into the USB port of a PC computer

to charge or connect the USB power adapter for charging (USB power adapter sold separately);

charging, USB line indicator lights switch off automatically after charging is completed ; charging

time is 60-90 minutes.

Remote Control Keypad and LCD Manual

Antenna

Power Indicator

H/L Speed Switch

Left Function Lever

(Throttle Lever)

Power On/Off

Right Function Lever

(Direction Lever)

Turn Lft/Right Fine-tuning

Tail Blade Fine-tuning

LCD Manual

Helicopter shows

(Power-on display)

Signal Shows

Normal to full case

Turn Left Shows

(Power-on without display

Throttle shows

(Power-on start in middle)

H/L Speed Shows

(Changed by "H/L Speed Switch")

Battery Indicator(According to

the power of batteries)

Forward Shows(Power-on start

in the centering)

Turn Right Shows(Power-on without

display)

Tail Blade Fine-tuning(Power-on

start in middle

Backward ShowsPower-on

without display)

Turn Left/Right Fine-tuning Shows

(Power-on start in centering)

Rotates

Anticlockwise

Rotates

Anticlockwise

Rotates Anticlockwise

Rotates

Clockwise

Rotates Clockwise

In hovering,when the tail

blade rotates clockwise

anticlockwise,please use

this button for fine-tuning

as figure shows.

When the helicopter lose

hovering with automatic

anticlockwise/clockwise

rotation,please use the

right/left inching switch

yo keep balance.

1.Beginner mode (the default setings

low speed)

2.Advanced mode:Press the button

on top left of controller, enter or

exit from the mode. Advanced

mode high speed brings more

pleasure to you

H/L Speed Switch

Transmitter

Problem Cause Check this

No reaction

from the

helicopter

1. Not enough power for the helicoper.

2. Not enough power for the controller.

3. The channel was different from helicopter and the

controller.

4. The gyro of the helicopter can't find out the right

point.

1. the remote control are running low.

2. antenna Weld.

1. replace the remote control batteries.

2. antenna re-welding.

Not reaction

from the

helicopter

when was fly

S32-01A

Head cover A

S32-01B

Head cover B

S32-01C

Head cover C

S32-02A

Tail decoration A

S32-02B

Tail decoration B

S32-02C

Tail decoration C

S32-05B

Connect buckle

S32-11

Tail components

S32-13A

S32-17

Motor A

S32-13B

Motor B

S32-14

3.7V Li-Poly

S32-15

Circuit board

S32-16

USB Charger

S32-12A S32-12B

Tail hold tube

S32-12C

Metal frame set

S32-12D

Main shaft

S32-06

Ascend and descend

S32-07

Gear A B

S32-10A

Battery case

S32-10B

Motor cover

S32-03A

Main blades

S32-03B

Tail blade

S32-04

Main frame

S32-05A

Balance bar

1. helicopter for charging.

2. replace the remote control batteries.

3. Close the remote control and the aircraft power

supply, re-code.

4.The helicopter flat on the ground, re-open the helicopter

power until the helicopter gyro re-tested.

Gyros S32 Using Instructions

Brand: Gyros

Model: S32

Type: Using Instructions

Download PDF

report

Gyros S32 Using Instructions

Gyros S32 Using Instructions

Related papers

Other documents