The Sony FA-ST1AM Sync Terminal Adaptor allows you to connect your external flash to your Sony digital single-lens reflex camera, enabling synchronized flash photography. Compatible with both center-positive and center-negative flash units, it features a battery check function to ensure sufficient power for up to 10,000 continuous releases. Experience versatile flash photography with precise synchronization and reliable performance.
The Sony FA-ST1AM Sync Terminal Adaptor allows you to connect your external flash to your Sony digital single-lens reflex camera, enabling synchronized flash photography. Compatible with both center-positive and center-negative flash units, it features a battery check function to ensure sufficient power for up to 10,000 continuous releases. Experience versatile flash photography with precise synchronization and reliable performance.
URL
http://www.sony.co.jp/alpha/support/
1 POWER
2
3 BATTERY CHECK
4 BATTERY CHECK
5
6
1
POWER ON
2
BATTERY CHECK
BATTERY CHECK
BATTERY CHECK
BATTERY CHECK
60 V
M
1/125
/
Printed on 70% or more rectcled paper
using VOC (Volatile Organic Compound)
-free vegetable oil based ink.
3-216-608-03 (1)
Sync Terminal Adaptor
Adaptateur de borne de
synchronisation
Operating Instructions
Mode d’emploi
Manual de instrucciones
FA-ST1AM
© 2007 Sony Corporation Printed in Japan
WB
1
2
POWER OFF
3
OFF
ON
4
POWER ON
5
POWER OFF
3V CR1220
1
OFF
2
3
4
+
5
60 V
3V CR1220
10,000
34 25 55 mm
22 g
0
C +40
C
-20
C +60
C
FA-ST1AM 1
3V CR1220
1
8
FA-ST1AM
108-0075 1-7-1
0570-00-0770
PHS 0466-38-0231
9 8
9 5
FA-ST1AM
English
Before operating the product, please read this manual
thoroughly and retain it for future reference.
WARNING
To reduce re or shock hazard, do not expose the unit to
rain or moisture.
When the lithium battery becomes weak, replace the
battery with a Sony CR1220 lithium battery. Use of another
battery may present a risk of re or explosion.
Battery may explode if mistreated. Do not recharge,
disassemble or dispose of in re.
For the State of California, USA only
Perchlorate Material
special handling may apply, See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains perchlorate.
For the Customers in Europe
is product has been tested and found compliant with the
limits set out in the EMC Directive for using connection
cables shorter than 3 meters (9.8 feet).
Disposal of Old Electrical & Electronic
Equipment (Applicable in the
European Union and other European
countries with separate collection
systems)
is symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment.
By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise
be caused by inappropriate waste handling
of this product. e recycling of materials
will help to conserve natural resources.
For more detailed information about
recycling of this product, please contact
your local Civic Oce, your household
waste disposal service or the shop where
you purchased the product.
< Notice for the customers in the
countries applying EU Directives >
e manufacturer of this product is Sony Corporation,
1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. e
Authorized Representative for EMC and product safety is
Sony Deutschland GmbH, Hedelnger Strasse 61, 70327
Stuttgart, Germany. For any service or guarantee matters
please refer to the addresses given in separate service or
guarantee documents.
Notes on use
A note about the battery
Depending on the time elapsed since manufacture
of the batteries, their life may vary from the values
described in this operating instructions, even if this unit
is provided with new batteries. We recommend having
spare batteries. It should be noted that battery capacity
decreases as temperatures drop. Allow the battery
to return to normal room temperature to restore the
battery to its normal charge.
Operating temperature
Rapid changes in temperature cause condensation to
form inside this unit. If you bring this unit directly in
from a cold environment to a warm environment, seal
the unit in a plastic bag while you are outdoors, and
try to extract as much air as you can from inside the
bag. You can remove the unit from the bag when the
air temperature around the bag has had a chance to
gradually rise.
Other cautions
is unit is not waterproof. If it comes in contact with
water, wipe it dry with a clean cloth and take it to the
nearest Sony dealer immediately.
Never attempt to disassemble this unit. Take it to the
nearest Sony dealer immediately for repair.
When dirty, this unit may be cleaned with a clean, dry
cloth. Do not allow this unit to come in contact with
alcohol or other chemicals.
Never leave this unit where it may be subjected to
extreme temperatures, such as the glove compartment
of a car, or to high humidity.
Do not touch the unit with wet hands. is may cause
electric shock.
Do not touch the sync terminal while connecting to the
ash.
Compatibility
For details about this unit and digital single reex
camera compatibility, refer to the following URL.
http://www.sony.net
Identifying the parts
1
POWER switch
2
Release button
3
BATTERY CHECK lamp
4
BATTERY CHECK button
5
Mounting foot
6
Sync terminal
Battery capacity
Before using the battery, ensure that it has sucient power
for the following operations.
1
Turn on the unit΄s power by sliding the
POWER switch to ON.
2
Hold down the BATTERY CHECK button.
If the battery has a sucient charge, the BATTERY
CHECK lamp (green lamp) will light while pressing
the BATTERY CHECK button.
If the BATTERY CHECK lamp starts to blink,
the battery does not have a sucient charge. It is
recommended that you change the battery. If the
BATTERY CHECK lamp does not light or blink, the
battery must be replaced.
Using this unit
is unit can be used by attaching it to the ash with sync
cord using the following operations. is unit is designed
for use with ash units having a voltage of 60 V or less.
e sync terminal is compatible with both center positive
(normal polarity) and center negative (positive polarity)
ash units.
When using the ash with this unit, set the camera as
following.
Set the exposure mode to M mode.
Set the shutter speed equal to whichever is slower: 1/125
second or a recommended preset level, or to a slower
speed.
When using the custom white balance, set the shutter
speed and aperture to the required exposure and use
a gray card for calibration. If you use a white card,
the light level will exceed the measurable light level.
“Custom WB error” will appear on the LCD screen of
the camera. If this message appears, it means that there
is unexpected value (when ashing close to the object or
exposing to a colorful object). It is recommended that
you set the white balance again to get a more correct
white balance value. For details, refer to the operating
instructions of the digital single lens reex camera.
Flash metering correction is unavailable.
1
Slide the accessory shoe cap of the camera.
2
Turn off the unit΄s power and slide the
mounting foot into the auto-lock accessory
shoe of the camera.
Slide the mounting foot of this unit rmly until it
clicks.
3
Plug the sync cord of the external flash unit
into the sync terminal of this unit.
When connecting the sync cord to this unit, turn o
the power to the ash that is connected to the sync
cord. e ash unit may ash if the camera is turned
on while the sync cord is plugged into the sync
terminal.
4
Turn on the unit΄s power by sliding the
POWER switch to ON.
Sync ash photography using an external ash is
available.
Flash units with a low trigger voltage may not work.
Regardless of whether there was a ash, battery power
is depleted by pressing the shutter button.
5
After use, turn off the unit΄s power and
remove the unit by sliding it in the direction
of arrow while pressing the release button.
Changing the batteries
Use a button type 3V lithium battery (CR1220) with this
unit.
1
Slide the battery-chamber cover in the
direction of arrow to remove the cover.
Turn o the power of this unit when replacing the
battery.
2
Insert a regular screwdriver or small, flat
and thin object, into the space between the
battery and adaptor body as illustrated.
Notes
Do not insert your ngernail because you can be
injured.
Do not insert an object that it is thicker than the
space because you can damage the unit.
Do not apply excessive force to the terminal in the
battery-chamber by inserting anything.
3
Press the battery lightly with your finger
not to pop out it as illustrated and press the
battery with the regular screwdriver to the
direction of the arrow to remove the battery.
Be careful not to pop out the battery when removing
it.
4
Put the battery + pole facing upward, and fit
the battery into its holder as illustrated.
5
Slide the battery-chamber cover in the
direction of arrow until it clicks to secure the
cover in place.
Specifications
Voltage 60 V or less
Compatible with center-positive
and center negative polarities
Battery Button type 3V lithium battery
(CR1220)
Battery life Approx. 10,000 continuous releases
Dimensions (Approx.) 34 × 25 × 55 mm (w / h / d)
(1 3/8 × 1 × 2 1/4 inches)
(excluding the projecting parts)
Mass (Approx.) 22 g (0.8 oz)
Operating temperature 0 ˚C to +40 ˚C (+32 ˚F to +104 ˚F)
Storage temperature -20 ˚C to +60 ˚C
(-4 ˚F to +140 ˚F)
Included items Sync terminal adaptor
FA-ST1AM (1)
(A button type 3V lithium battery
(CR1220) installed)
Set of printed documentation
Design and specications are subject to change without
notice.
is a trademark of Sony Corporation.
1
2
3
4
5
6
1 2
3
4
5
1 2
3 5
Page is loading ...
-
1
-
2
The Sony FA-ST1AM Sync Terminal Adaptor allows you to connect your external flash to your Sony digital single-lens reflex camera, enabling synchronized flash photography. Compatible with both center-positive and center-negative flash units, it features a battery check function to ensure sufficient power for up to 10,000 continuous releases. Experience versatile flash photography with precise synchronization and reliable performance.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Sony FA-ST1AM Manuel utilisateur
- español: Sony FA-ST1AM Manual de usuario
Related papers
Other documents
-
Nikon SB-30 User manual
-
Canon Macro Ring Lite MR-14EX II User manual
-
-
Nikon SB-400 User manual
-
Heath Zenith SL-6201 - Heath - Wireless Pushbutton User manual
-
-
Canon Speedlite 90EX User manual
-
Metz Mecablitz 45 CL-4 Owner's manual
-
Yamaha TSX-140 Owner's manual
-
Canon Speedlite 270EX II Flash User manual