J51
BARRIER FREE
© 2008 AS America Inc.
31"
(787mm)
SUGGESTED
34"
(864mm)
7-5/8"
(194mm)
15-1/2"
(394mm)
15-1/2"
(394mm)
8"
(203mm)
1-1/4" O.D. TAILPIECE
1-1/4" O.D. WASTE
FINISHED FLOOR
*10-3/4"
(273mm)
*12-7/8"
(327mm)
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
5/8"
(16mm)
6"
(152mm)
SUPPLIES
AS REQ'D
1-3/4" DIA.
STD. DRAIN
OUTLET
45
o
2" (51mm)
MINIMUM
2-1/2" (64mm)
EDGE OF
COUNTERTOP
CUTOUT
FINISHED WALL
OR SPLASHBACK
1-1/4" DIA. C.H.
(TYPICAL)
MTG CLIP
(4 PLACES)
CUTOUT
AREA
DETAIL OF MOUNTING CLIP
(KIT No.47194.0070A)
LAVA
BRASS
INSERT
19mm
(3/4) MIN.
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
FITTING
CENTER-SET
SPREAD
A
27mm(1-1/16)
32mm(1-1/4)
B
102mm(4)
203mm(8)
686mm
(27)
MIN.
864mm
(34)
76mm
(3)
610mm
(24)
BARRIER FREE
CLEARANCE
152mm
(6)
MAX.
229mm
(9)
MIN.
203mm
(8)
MIN.
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
NOTES:
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
SUGGESTED.
▼ UNDERCOUNTER MOUNTING KIT SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
USE ENCLOSED TEMPLATE FOR COUNTERTOP CUTOUT.
SEALING COMPOUND SUPPLIED BY OTHERS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.2. These measurements
are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided pages.
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Linen
❏ Silver ❏ Fawn Beige ❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
* See faucet section for additional models available
MEETS THE AMERICANS WITH DISABILITIES ACT
GUIDELINES AND ANSI A117.1 ACCESSIBLE AND
USABLE BUILDINGS AND FACILITIES -
CHECK LOCAL CODES.
Countertop 864mm (34") from finished floor. Lavatory
installed 51mm (2") MIN. from front edge of countertop.
Countertop thickness to be 25mm (1") maximum.
ORBIT™
UNDERCOUNTER SINK
VITREOUS CHINA
ORBIT™ UNDERCOUNTER SINK
• Round undermount sink
• Made from vitreous china
• Front overow
• Unglazed rim for undercounter mounting
• Supplied with mounting kit (047194-0070A)
and template
❏ 0630.000 Sink less faucet deck
Nominal Dimensions:
394mm dia. (15-1/2") Round
Bowl sizes:
324mm (12-3/4") wide
111mm (4-3/8") deep
Compliance Certications -
Meets or Exceeds the
Following Specications:
• ASME A112.19.2M for
Vitreous China Fixtures
• CAN/CSA B45 series
Revised 2/08
/