Paradigm 400 User manual

Page is loading ...

1

Paradigm DOES NOT supply hardware for mounting speakers to the

wall. Hardware shown in this manual is for example only and will vary

depending on the wall type. Always use screws appropriate for wall type

and weight of speakers.

If installing into drywall, install into 1/2˝ (13 mm) or 5/8˝ (16 mm) drywall

only. Screws must be long enough to go through anchor bolts

(not

supplied)

and firmly into drywall (see inset circle, page 12).

IMPORTANT: Please read before wall mounting speakers.

Wall mount speakers securely enough that they cannot fall and cause

personal injury or damage to property. Use safety straps (if included).

Detailed information on attaching the safety straps is included in the

section on Wall Mounting later in the manual.

NON LIABILITY: We are aware that the wall-mounting assemblies provided for

Cinema speakers could be used for purposes and in ways other than those for which

they were intended. The manufacturer, distributor, retailer and their respective

agents cannot be held responsible or liable for injuries or property damage—direct,

indirect or consequential—arising from the use of or inability to use these products

safely and properly. Every effort has been made to provide accurate, error-free

installation instructions. Paradigm Electronics Inc. disclaims liability for difficulties

that may arise from the misinterpretation of information contained in these

instructions.

Paradigm Electronics Inc. 205 Annagem Blvd., Mississauga, ON Canada L5T 2V1 032511

RECYCLING AND REUSE GUIDELINES (Europe)

In accordance with the European Union WEEE (Waste Electrical and Electronic Equipment) directive effective August 13, 2005, we would like to notify you that our speakers may contain

regulated materials which, upon disposal, require special reuse and recycling processing. For this reason Paradigm Electronics Inc. (the manufacturer of Paradigm speakers and Anthem

electronic products) has arranged with its distributors in European Union member nations to collect and recycle this product at no cost to you. To find your local distributor please contact

the dealer from whom you purchased this product or go to our website at www.paradigm.com.

Please note that only the product falls under the WEEE directive. When disposing of packaging and other shipping material we encourage you to recycle through the normal channels.

2

TABLE OF CONTENTS

Your New Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

How to Avoid Speaker Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Speaker Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Stand Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Speaker Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Thank you for choosing award-winning Cinema

™

speakers and congratulations. You are

about to hear the difference these sonically accurate speakers will make in your music and

home theater system. They are the product of countless hours of comprehensive research and

development and will reward you with exceptional sound for many years.

To ensure proper installation please read this manual and follow all instructions. If you have

further questions contact your Authorized Paradigm

®

Dealer or visit the Q&A page on our

website at www.paradigm.com.

YOUR NEW SPEAKERS

Paradigm Cinema speakers are ideally suited to a variety of lifestyle applications. They are designed to

allow easy installation throughout your home. To ensure the best performance possible we strongly

recommend that you observe the placement guidelines provided in the “Speaker Placement” section.

Cleaning

Do not use a strong or abrasive cleaner on your speakers. Clean them with a soft damp cloth but do not

get them wet.

On Stands or Wall Mounting

We include tabletop/shelf stands (supports) and wall-mounting brackets for Cinema speakers (varies

by model). See the illustrations later in the manual for how to mount them to stands and wall brackets.

Paradigm floorstanding stands are also available for your new Cinema 100s at an additional charge (see

your dealer for more information).

IMPORTA

NT! If wall mounting take extra care during the installation process—always use the safety

straps (if included) as secondary restraints.

HOW TO AVOID SPEAKER DAMAGE

Use an appropriate amplifier. At high volumes, a very powerful amplifier can overdrive your speakers

and damage them. On the other hand, if your amplifier isn’t powerful enough, it can produce clipping

distortion that can easily damage high-frequency dri

vers (see dealer).

Don’t be fooled by your amplifier’s volume control. It adjusts listening level—it does not indicate

power output. If your speakers begin to sound harsh or grating, or if you hear the bass breaking up turn

the volume down immediately or you will damage your speakers! This type of damage constitutes

abuse and is not covered by warranty!

Tone controls and equalizers can demand e

ven more power from an amplifier, lowering the point at

which it produces clipping distortion. Use them sparingly, if at all, and do not use them when listening

at loud levels.

SPEAKER PLACEMENT

The following placement guidelines will help you get the best performance from your Cinema speakers.

Ilustrations showing you how to attach speakers to stands and wall-mounting brackets are provided in

the section following this one. For the Cinema

™

Trio, follow placement instructions provided in the

illustration on page 5.

Front Speakers (Left/Right)

On the Stands (See illustration opposite)

For the most accurate timbral balance, place your front speakers so that their high-frequency drivers

(tweeters) point toward the listening area and sound arrives at approximately ear level.

On the Wall (See illustration opposite)

Follow the placement directions provided in the paragraph above.

3

4

Center Speaker

On the Stand (see illustration below)

Place the center speaker on its stand below the display so that sound arrives as close to ear level as

possible. The speaker should sit about the same distance away from the listening area as the front speakers.

(Some receivers and processors electronically adjust for differences in distance between speakers… check to

see if yours does.)

On the Wall (see illustra

tion below)

Place the center speaker above or below the display, whichever position brings sound closest to ear

level. It should sit about the same distance away from the main listening areas as the front speakers. (See

note above about electronic adjustments for distance.)

OR

Surround and Rear Speakers

When used as surround/rear speakers, Cinema speakers should be kept well away from the listening

area for optimal surround-sound performance (as shown on next page). They can be placed on stands

(supports) or on the wall, following the assembly directions provided for the appropriate model.

5.1 Surround Configuration

(5.1 requires 5 speakers plus a subwoofer)

Position speakers on each side, corner, or rear of the listening area as shown on next page.

7.1 Surround Configuration

(7.1 requires 7 speakers plus a subwoofer)

Position one surround speaker on each side or corner of the listening area as shown on the next page.

Position additional rear speakers behind the listening area—one slightly to the right, the other slightly to

the left, also as shown on next page.

CINEMA

™

100, 200 & 400

Cinema

™

200/400

Left/Right speakers are

wall mountable only.

5

Cinema Trio (Front/Left/Center speakers in one unit)

Place the speaker above or below the display, whichever position brings sound closest to ear level. If also

using surround/rear speakers follow the directions for correct placement provided earlier.

OR

SPEAKER PLACEMENT (CONTINUED)

Surround and rear configurations shown

In a 7.1 configuration, choose side

or corner position for surrounds.

Rears should be positioned as shown.

OROR

OR

6

STAND MOUNTING (ALL HARDWARE INCLUDED)

CINEMA

™

100

Push down on terminal clips to

allow wire access. Connect wires

before attaching stand.

7

CINEMA

™

200 & 400

CINEMA

™

TRIO

Self-adhesive bumper pads

Stand is only used when speaker

is in a horizontal configuration

Stands are only used when speaker

is in a horizontal configuration

STAND MOUNTING (CONTINUED)

8

WALL MOUNTING

3.258"

If you are not comfortable performing the following procedures, have a professional perform

the installation (see your Authorized Paradigm

®

Dealer about hiring a professional).

TOLERANCE UNLESS OTHERWISE SPECIFIED

5

Step 3Step 2

Step 1

CINEMA

™

100

Assemble all parts before moving to Step 3

Attach bracket to wall

(screws not supplied)

Vertical:

Speakers tilt left/right

to further improve

stereo imaging

Horizontal:

Speaker tilt up/down

for optimal dialog clarity

Do not tighten completely

with allen key until

you adjust for

desired angle

9

WALL MOUNTING (CONTINUED)

Attach locking

cover to bracket

and screw in

Step 5 Step 6

Step 4

Step 6 Step 7

Step 4

Push down on

terminal clips to

allow wire access

Step 4Step 5

Snake wires from

inside wall through

hole in bracket

WIRING INSIDE THE WALL

10

Push down on

terminal clips to

allow wire access

Snake wires

through hole

in locking cover

Attach locking

cover to bracket

and screw in

Step 6 Step 7

Step 4Step 4 Step 4Step 5

WIRING ALONG THE WALL

11

WALL MOUNTING (CONTINUED)WALL MOUNTING (CONTINUED)

Bracket is slotted (see illustration), to allow further adjustment up or down, if necessary. Re-check to

ensure bracket is level. Mark inner screw holes.

Step 2

WARNING! For stability, all four

screws MUST be used

Position bracket and ensure it is level. Mark the two center screw holes. Drill pilot holes, then press

anchor bolts firmly into drywall and screw in. Follow with flathead screws: DO NOT SCREW ALL THE

WAY IN AT THIS POINT—leave screw heads protruding slightly.

VERTICAL MOUNTING

FOR CINEMA

™

200, 400 & TRIO

Wall screws not supplied

Step 1

Position bracket vertically

on wall as shown, then

follow the steps for

horizontal positioning.

NOTE: This step is for

positioning only. Screws

will be removed in next

step to allow installation of

additional anchor bolts

HORIZONTAL MOUNTING

FOR CINEMA

™

200, 400 & TRIO

12

Remove the two flathead screws (not shown). Drill inner pilot holes,

then press anchor bolts firmly into drywall and screw in. Now insert

all four flathead screws and tighten.

WARNING! All screws must

be inserted straight and fully

tightened to ensure correct

operation of anchor bolts.

Step 3

CINEMA

™

200 & 400 WIRING

CINEMA

™

TRIO WIRING

Safety strap

attaches here

Safety strap

attaches here

13

3.258"

SPEAKER CONNECTION

Turn your amplifier OFF before connecting speakers. This will avoid damage

which could result from accidental shorting of speaker cables.

LENGTH DIAMETER GAUGE

Under 4.5 m (15 ft) 1.3 mm (0.05 in) 16 awg

Under 9 m (30 ft) 1.6 mm (0.06 in) 14 awg

Over 9 m (30 ft) 2.0 mm (0.08 in) 12 awg

MINIMUM GAUGE REQUIREMENTS

Your speakers are equipped with binding posts that can be used with pin connectors, as well as with

bare wire. Refer to the diagram below and using high-quality speaker cable (see your dealer), connect

one speaker at a time to your receiver/amplifier. Connect the red (+) amplifier terminal to the red (+)

speaker terminal and the black (–) to the black (–) (see next page). Push binding posts to secure.

Turn your amplifier on and listen to your speakers. If you notice a complete lack of mid-bass and a

dislocated image, one or more of your speakers may be connected out-of-phase (their polarity is

reversed). Re-check to ensure that each speaker’s cable is connected with correct polarity: red (+) to

red (+) and black (–) to black (–). Make sure wires are firmly fastened. Push binding posts to secure.

The following chart identifies the minimum gauge requirements for various cable lengths:

Align keyhole slots (see inset) on rear of speaker with protruding screw heads on the bracket, then using

an “in and down” motion mount speaker on bracket.

CINEMA

™

200, 400 & TRIO

WALL MOUNTING (CONTINUED)

14

SOLUTION

PROBLEM

No Sound

from One or

More Speakers

No Sound

Lack of Bass or

Dislocated Image

•

Make sure receiver, preamp or amplifier is plugged in and turned on.

Check power outlet at the wall is working.

• Are headphones plugged in, or is the system on Mute?

• Re-check all connections.

• Check your balance control or VC-150 Volume Control (if using).

• Check that all power cords are properly plugged in and functioning

•

Swap a non-working speaker with one that works to determine if the

problem is with the speaker or something else (i.e. wiring, amplifier).

• One or more speakers may be connected out of phase (their polarity

is reversed).

• Re-check to ensure that each speaker’s cable is connected with correct

polarity: red (+) to red (+) and black (-) to black (-).

TROUBLESHOOTING GUIDE

CINEMA

™

TRIO

CINEMA

™

100, 200 & 400

15

Design

Crossover(s)

High-Frequency Driver(s)

Bass / Midrange Driver(s)

Bass Driver(s)

Low-Frequency Extension*

Frequency Response:

On-Axis

30˚ Off-Axis

Sensitivity – Room / Anechoic

Suitable Amplifier Power Range

Maximum Input Power

†

Impedance

Dimensions (h x w x d)

Weight (unpacked)

Finishes

2-driver, 2-way acoustic suspension,

stand-mounted / wall-mounted

2nd-order electro-acoustic

at 1.8 kHz

25-mm (1 in) S-PAL

™

satin-

anodized pure-aluminum dome,

ferro-fluid damped and cooled

90-mm (3-1/2 in) mineral-filled

polypropylene cone, 25-mm (1 in)

high-temperature voice coil,

oversize ceramic / ferrite magnets

n/a

85 Hz (DIN)

±2 dB from 125 Hz – 20 kHz

±2 dB from 125 Hz – 15 kHz

88 dB / 85 dB

15 – 100 watts

50 watts

Compatible with 8 ohms

21.2 cm x 12.2 cm x 15.7 cm

8-3/8 in x 4-13/16 in x 6-3/16 in

1.8 kg / 4.0 lb per speaker (with stand)

Black Gloss

TECHNICAL SPECIFICATIONS

CINEMA

™

100 CINEMA

™

200

3-driver, 2-way LCR, acoustic

suspension, on-wall with option to

sit center speaker on a table or

shelf with supports included

2nd-order electro-acoustic

at 1.8 kHz

25-mm (1 in) S-PAL

™

satin-

anodized pure-aluminum dome,

ferro-fluid damped and cooled

Two 90-mm (3-1/2 in) mineral-

filled polypropylene cones, 25-mm

(1 in) high-temperature voice coil,

oversize ceramic / ferrite magnets

n/a

80 Hz (DIN)

±2 dB from 120 Hz – 20 kHz

±2 dB from 120 Hz – 15 kHz

90 dB / 87 dB

15 – 150 watts

70 watts

Compatible with 8 ohms

50.5 cm x 16.1 cm x 10.4 cm

19-7/8 in x 6-5/16 in x 4-1/16 in

3.7 kg / 8.3 lb per speaker

Black Gloss

16

Design

Crossover(s)

High-Frequency Driver(s)

Bass / Midrange Driver(s)

Bass Driver(s)

Low-Frequency Extension*

Frequency Response:

On-Axis

30˚ Off-Axis

Sensitivity – Room / Anechoic

Suitable Amplifier Power Range

Maximum Input Power

†

Impedance

Dimensions (h x w x d)

Weight (unpacked)

Finishes

5-driver, 2-1/2-way LCR, acoustic

suspension, on-wall with option to

mount center configuration on

table or shelf

2nd-order electro-acoustic at 2.1

kHz; 2nd-order electro-acoustic

a

t 500 Hz (bass drivers)

25-mm (1 in) S-PAL

™

satin-

anodized pure-aluminum dome,

ferro-fluid damped and cooled

Two 90-mm (3-1/2 in) mineral-

filled polypropylene cones, 25-mm

(1 in) high- temperature voice coil,

oversize ceramic / ferrite magnets

Two 90-mm (3-1/2 in) mineral-

filled polypropylene cones, 25-mm

(1 in) high- temperature voice coil,

oversize ceramic / ferrite magnets

75 Hz (DIN)

±2 dB from 115 Hz – 20 kHz

±2 dB from 115 Hz – 15 kHz

95 dB / 92 dB

15 – 200 watts

100 watts

Compatible with 8 ohms

67.0 cm x 16.1 cm x 10.4 cm

26-3/8 in x 6-5/16 in x 4-1/16 in

5.8 kg / 12.8 lb per speaker

Black Gloss

CINEMA

™

400 CINEMA

™

TRIO

All-in-one left / right / center:

7-driver, 3-channel, 2-way,

acoustic suspension

2nd-order electro-acoustic

at 1.8 kHz

Three 25-mm (1 in) S-PAL

™

satin-

anodized pure-aluminum domes,

ferro-fluid damped and cooled

Four 90-mm (3-1/2 in) mineral-

filled polypropylene cones, 25-mm

(1 in) high- temperature voice coil,

oversize ceramic / ferrite magnets

n/a

85 Hz (DIN)

±2 dB from 125 Hz – 20 kHz

±2 dB from 125 Hz – 15 kHz

89 dB / 86 dB

15 – 150 watts

70 watts per channel

Compatible with 8 ohms

16.1 cm x 91.5 cm x 10.4 cm

6-5/16 in x 36 in x 4-1/16 in

7.6 kg / 16.8 lb per speaker

Black Gloss

*

DIN 45 500 Indicates -3 dB in a typical listening room.

†

With typical program source, provided the amplifier clips no more than 10% of the time.

17

LIMITED WARRANTY

Paradigm

®

speakers covered in this manual are warranted to be and remain free of manufacturing

and/or material defects for a period of five (5) years from the date of original purchase.

Within the time periods specified, repair, replacement or adjustment of parts for manufacturing and/or

material defects will be free of charge to the original owner.

Thermal Or Mechanical Abuse/Misuse Is Not Cove

red Under Warranty.

Limitations:

• Warranty begins on date of original retail purchase from an Authorized Paradigm

®

Dealer only. It is

not transferable

• Warranty applies to product in normal home use only. If product is subjected to any of the

conditions outlined in the next section, warranty is void

• Warranty does not apply if the product is used in professional or commercial applications

Warra

nty is Void if:

• The product has been abused (intentionally or accidentally)

• The product has been used in conjunction with unsuitable or faulty equipment

• The product has been subjected to damaging signals, derangement in transport, mechanical

damage or any abnormal conditions

• The product (including cabinet) has been tampered with or damaged by an unauthorized

service facility

• The serial number has been remove

d or defaced

Owner Responsibilities:

• Provide normal/reasonable operating care and maintenance

• Provide or pay for transportation charges for product to service facility

• Provide proof of purchase (your sales receipt given at time of purchase from your Authorized

Paradigm

®

Dealer must be retained for proof-of-purchase date)

Should servicing be required, contact your nearest Authorized Paradigm

®

Dealer, Paradigm Electronics

Inc. or Import Distributor (outside the U.S. and Canada) to arrange, bring in or ship prepaid, any defective

unit. Visit our website, www.paradigm.com for more information.

Paradigm Electronics Inc. reserves the right to improve the design of any product without assuming any

obligation to modify any product previously manufactured.

This warranty is in lieu of all other warranties expressed or implied, of merchantability, fitness for any

particular purpose and may not be extended or enlarged by anyone. In no event shall Paradigm

Electronics Inc., their agents or representatives be responsible for any incidental or consequential

damages. Some jurisdictions do not allow limitation of incidental or consequential damages, so this

exclusion may not apply to you.

Retain this manual and your sales receipt for proof of warranty term and proof of purchase.

Page is loading ...

6

MONTAGE SUR UN PIED (TOUT LE MATERIEL NECESSAIRE EST COMPRIS)

CINEMA

MC

100

Poussez vers le bas pour permettre

un accès aux câbles. Raccordez les

câbles avant de fixer le support.

Page is loading ...

Paradigm 400 User manual

Paradigm 400 User manual

in other languages

Related papers

Other documents