Gordon 66691 User manual

Brand: Gordon

Model: 66691

Type: User manual

This manual is also suitable for

GORDON 66691

1 MILLION CANDLE-POWER

RECHARGEABLE SPOT LIGHT

66691

OPERATING AND MAINTENANCE INSTRUCTIONS

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2009 by Harbor Freight Tools

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Manual Revised 10d

SKU 66691 For technical questions, please call 1-800-444-3353. Page 2

SAVE THIS MANUAL

Keep this manual for the safety warn-

ings and precautions, assembly, operat-

ing, inspection, maintenance and cleaning

procedures. Write the product’s serial

number in the back of the manual near the

assembly diagram (or month and year of

purchase if product has no number). Keep

this manual and the receipt in a safe and

dry place for future reference.

When using this

Rechargeable Spot Light,

basic safety precautions

should always be followed to

reduce the risk of re, electric

shock, and personal injury,

including the following:

Always wear ANSI-approved safety 1.

goggles during battery removal and

installation.

Inspect before each use. Do not use 2.

if the battery is leaking or damaged in

any way.

Never point the light beam from this 3.

Rechargeable Spot Light directly into

the eyes of any person, or animal.

If using this Spot Light near a road-4.

way, DO NOT point light beam into

oncoming trafc.

Do not use this Spot Light for any 5.

purpose except that for which it is

intended.

Store idle Rechargeable Spot Light 6.

indoors when not in use. Store high,

out of the reach of children.

WARNING: This product contains 7.

lead, which is a chemical known to

the State of California to cause can-

cer and birth defects or other repro-

ductive harm. (California Health &

Safety Code § 25249.5, et seq.)

Maintain labels and nameplates on 8.

the Rechargeable Spot Light. These

carry important safety information. If

unreadable or missing, contact Har-

bor Freight Tools for a replacement.

The warnings, precautions, and in-9.

structions discussed in this instruction

manual cannot cover all possible con-

ditions and situations that may occur.

It must be understood by the operator

that common sense and caution are

factors which cannot be built into this

product, but must be supplied by the

operator.

SAVE THESE

INSTRUCTIONS.

SKU 66691 For technical questions, please call 1-800-444-3353. Page 3

SPECIFICATIONS

Rechargeable Battery

4V DC 2AH Sealed

Lead Acid (Included, Not

Replaceable).

Bulb

25W Halogen (H3 4V

25W)

AC/DC Adaptor

Input: 120VAC 60 Hz

(Included)

Adaptor Prongs 2-Prong, Non-Polorized

Cigarette Lighter

Adaptor

12V DC, Fuse: 2A 250V

(Included)

Light Output 1 Million Candle Power

Please Note: Spotlight will NOT operate

during charging.

UNP ACKING

When unpaing, make sure that the

item is intact and undamaged. If any parts

are missing or broken, please call Harbor

Freight Tools at the number shown on the

cover of this manual as soon as possible.

OPERATING INSTRUCTIONS

Read the ENTIRE IMPORTANT

SAFETY INFORMATION section

at the beginning of this manual

including all text under

subheadings therein before set

up or use of this product.

Charging with AC/DC Adaptor:

Plug AC/DC Adaptor (21) into a 120V 1.

outlet.

Attach the end of the Adaptor cord to 2.

the Adaptor Cord Inlet, located on the

back of the Spot Light. See Figure 1.

The Charge Light Indicator will light 3.

up. When the Charge Light Indicator

goes out, the Spot Light is ready for

use. Unplug the Adaptor.

Charging with 12V Cigarette Lighter

Adaptor: Plug into any 12V DC outlet in a

Automobile, boat or RV, and then into the

Adaptor Plug Inlet located on the back of

the Spot Light. See Figure 1.

Figure 1

Charge Light

Indicator

Pistol

Grip

Adaptor Plug Inlet

4. The Charge Light Indicator will light

up. When the Charge Light Indicator

goes out, the Spot Light is ready for

use. Unplug the Adaptor.

A fully charged Spot Light will give 5.

bright light for approximately 20 min-

utes.

NOTE: Spotlight will not operate 6.

during charging.

Using the Rechargeable Spot Light:

Hold the Spot Light using the Pistol 1.

Grip (4).

Squeeze the Switch (6) located on 2.

the Trigger (8). If you want the Spot

Light to stay on, push the Switch

Lock (5) in while squeezing the Trig-

Rev 10d

SKU 66691 For technical questions, please call 1-800-444-3353. Page 4

ger (8), then release the Trigger (8)

and the Spot Light will stay on.

When nished using the Spot Light, 3.

squeeze the Trigger to turn the Spot

Light off. Let the Bulb (14) cool for

at least 30 minutes before storing.

Keep Spotlight indoors away from

children.

Replacing the 4V Halogen Bulb:

Remove the Ring Cover (12) from the 1.

Housing (2) by un-threading with a

counterclockwise motion.

Lift out Ring (11), Lens (10), and 2.

Reective Bowl (9). The Bulb (14) is

installed into base of Reective Bowl.

Remove the Metal Spring Clip (22)3.

holding the Bulb Holder in place by

squeezing and lifting the Spring Clip

up through the “T” slot.

NOTE: To prevent hand-oil contam-4.

ination, DO NOT touch the Halogen

Bulb (14) with bare hands. Use a

lint free, soft, clean rag to handle

the Bulb. Remove the Bulb from the

Bulb Holder by twisting it counter-

clockwise and lifting.

Replace with new, identical Bulb 5.

(25W Halogen H3 4V).

Place Bulb Holder into the Reective 6.

Bowl (9). Slide the closed end of the

Metal Spring Clip (22) over the tab at-

tached to the side of the Bulb Holder,

and squeeze the Spring Clip together

while sliding it into the “T” slot.

Replace the Reective Bowl (9), the 7.

Lens (10), and the Ring (11). Hold

these in place while threading the

Ring Cover (12) onto the Spot Light

with a clockwise motion.

Removing and Recycling the 4V DC

Battery:

NOTE: The Battery for this product is

rechargeable and long lasting.

When nally it is worn beyond any

further use, it should be removed

and recycled and the Spot Light

should be disposed of with normal

refuse. DO NOT dispose of the

Spot Light with Battery inclosed in

it’s Housing.

Figure 2

Seven Screws

Hold Housing

Together

1. To remove the Battery from the Hous-

ing (2), follow these steps:

Remove seven Screws from the a.

Housing. See Figure 2.

Pull the Housing (2) apart and re-b.

move the wires connected to the

Battery.

Remove the Battery from the Hous-c.

ing (2).

WARNING! DO NOT dispose of the

4V Lead Acid Battery with normal

refuse. Always recycle in ac-

cordance with all local, state and

federal rules and regulations.

SKU 66691 For technical questions, please call 1-800-444-3353. Page 5

PARTS LIST

Part Description Q’ty

1 Circuit Board 1

2 Housing 1

3 Pistol Grip Holder 1

4 Pistol Grip 1

5 Switch Lock 1

6 Switch 1

7 Trigger Spring 1

8 Trigger 1

9 Reective Bowl 1

10 Lense 1

11 Ring 1

PARTS LIST

Part Description Q’ty

12 Ring Cover 1

13 Screw 2

14 Halogen Bulb (25W H3 4V) 1

15 Screw (Housing) 7

16 Battery 1

17 Screw 2

18 Circuit Board 1

19 Wrist Wrap 1

20 Auto, Boat, RV, 12V DC Adaptor 1

21 AC/DC Adaptor (120V) 1

22 Metal Spring Clip 1

ASSEMBLY DIAGRAM

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not available

individually as replacement parts.

SKU 66691 For technical questions, please call 1-800-444-3353. Page 6

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high

quality and durability standards, and warrants to the original purchaser that this product

is free from defects in materials and workmanship for the period of 90 days from the date

of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,

abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,

improper installation, normal wear and tear, or to lack of maintenance. We shall in no event

be liable for death, injuries to persons or property, or for incidental, contingent, special

or consequential damages arising from the use of our product. Some states do not allow

the exclusion or limitation of incidental or consequential damages, so the above limitation

of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with

transportation charges prepaid. Proof of purchase date and an explanation of the complaint

must accompany the merchandise. If our inspection veries the defect, we will either

repair or replace the product at our election or we may elect to refund the purchase price

if we cannot readily and quickly provide you with a replacement. We will return repaired

products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning

the product.

This warranty gives you specic legal rights and you may also have other rights which

vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT

HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR

DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE

UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER

ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL

PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION

OF REPLACEMENT PARTS THERETO.

Gordon 66691 User manual

Brand: Gordon

Model: 66691

Type: User manual

This manual is also suitable for

GORDON 66691

Download PDF

report

Gordon 66691 User manual

This manual is also suitable for

Gordon 66691 User manual

Other documents