Z-Wave Sensative Strips Plus Ultra Thin Door/Window Contact Sensor Owner's manual

Type
Owner's manual
Sensative AB • Mobile Heights Center – Lund, Sweden • www.sensative.com Z-Wave Plus certified
Meet Strips.
SMARTHOME SOLUTIONS BY SENSATIVE
You wont believe
what youre
not seeing.
Strips by Sensative is a revolutionary magnetic sensor designed
to monitor and protect windows, doors and other valuables. It’s
so thin that in most cases, it can be mounted invisibly to the
end-user. With an adhesive strip it’s almost as easy to mount
as a sticker and the custom designed battery will last up to ten
years. With Z-Wave® technology, Strips fits in effortlessly with
existing Z-Wave® smarthome systems. Configuring Strips, you
can allow it to notify you when something is left open, when
something is opened when you’re not home and even be set
when you’re home sleeping.
BENEFITS
• Can notify you when you’ve left
a window or door open
• Can alert you when something
unexpected happens whether
you’re home or not
• Ultra-thin design allows Strips to
be mounted ”invisibly” between
most doors/windows and their
frames
• Simple to mount with the included
adhesive backing
• Easy to connect to any Z-Wave®
controller
• Up to 10 year battery life means
no more changing batteries
• Protects the perimeter of your
home even when you’re asleep
Ultra-thin – Less than 3mm
Two-way Z-Wave®
communication
Magnet sensor
Built-in battery
Adhesive backing
THE STRIPS
1. Top view 2. Side view Actual size: 195 × 15 × 2,98 mm (Scale 1:3)
1
2
WANT TO KNOW MORE?
www.sensative.com
Psst, your
window
is open.
Sensative AB • Mobile Heights Center – Lund, Sweden • www.sensative.com Z-Wave Plus certified
TECHNICAL DATA
Product Strips-MaZw
Features Magnet sensor, Tamper alert, LED indication.
Regions Europe (868.4 MHz)
Range
Up to 40 meters. Non-battery Z-Wave devices will act as
repeaters and may extend the range up to 150 m.
Dimensions
Sensor: 195*15*2.98 mm
Magnets: A: 30*11*1 mm, B: Diameter 12 * 3 mm
Operating conditions -20 to + 60 degree C. In- and outdoor usage.
Power supply
Built-in battery LiMnO2 battery.
Up to 10 years battery life.*
Magnetic range Approx. 15 mm
* Note: Usage of range extenders, short wake up intervals and usage in low or high
temperatures will shorten the battery life
Sensative believes that Strips is the next generation of smarthome magnetic sensor!
We are always on the lookout for new partners. Get in touch with us if you want more information
and let’s book a meeting. Contact Fredrik Westman or Neal Greenspan.
FREDRIK WESTMAN +46(0) 70-824 51 61 | fredrik.westman@sensative.com
NEAL GREENSPAN +46(0) 70-237 13 99 | [email protected]om
CONTENTS
Sensor with adhesive
backing
Magnet (A) with
adhesive backing
Magnet (B) with
adhesive backing
Manual
Cleaning cloth
Z-WAVE SPECIFICATIONS
Associations Group 1 (Lifeline). Max 1 node.
Notification type
Supports Binary sensor report, Notification report and
Basic report
Wake up intervals 30 min - 24 hours (default 24 h)
Device class GENERIC_TYPE_SENSOR_NOTIFICATION
Specific device class SPECIFIC_TYPE_NOTIFICATION_SENSOR
Command classes
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_SENSOR_BINARY
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_NOTIFICATION_V4
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_BATTERY
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_POWERLEVEL
Fredrik Westman
SALES & MARKETING
Mats Pettersson
CEO
Jeff Robertson
SOURCING & SUPPLY
Neal Greenspan
SALES & MARKETING
Partner with us

FRONTBACK
FOLDFOLDFOLD
Strips is a Z-Wave magnet sensor that can be added to any
certified Z-Wave system and operate with any brand Z-Wave
device.
Z-Wave is an international standard for wireless communication
in smart homes and buildings enabling you to monitor and
control your home remotely.
Please follow our three steps in this guide to get started.
1. Add (figure
1
4
) 2. Plan (figure
5
) 3. Place (figure
6
-
10
)
More guidance: www.sensative.com/Strips_tips
For good communication
Strips uses low power radio signals to communicate with your
Z-Wave controller. For best results, please consider the following:
Strips is designed to fit invisibly in most wood,
wood/aluminum, plastic windows and doors
Strips should not be mounted directly on metal surfaces or
within a metal structure as the range will be reduced.
The magnet should not be placed on metal.
Strips range is up to 40 meters.
Any non-battery Z-Wave device will act as a repeater to
increase network reliability and range. Usage of repeaters will
reduce Strips battery life.
For good functionality in the door or window
To place Strips invisibly, you need a gap with a minimum
height of 3.5 mm. If the round magnet fits, the gap height
should be enough.
Strips may be mounted on the frame (recommended)
and the magnet on the door/window, or vice versa.
Check that magnet (A) can be placed so that it is less
than 10 mm from Strips’ flat end when the window is closed.
When the window is open, the magnet should be at least
30 mm away from Strips.
Open the window/door fully to check that the place for
Strips and the magnet does not interfere with hinges or
locking mechanisms.
Please follow the steps below to correctly mount Strips:
1. Make sure the surface is clean, dry and at least + 10° C.
Use the included cloth to clean and prepare the surfaces.
2. Remove the short protective film from the small Strips
test adhesive. The small adhesive is used before the final
placement so it is easy to move Strips if needed.
3. Place Strips where you want it mounted. Check the position
by carefully closing the door/window and then opening it
completely again.
4. Measure and identify where the magnet (A) should be
placed. Remove the protective film and place the magnet.
Close and open again to validate that your Z-Wave
controller detected the changes. Re-mount if needed.
5. When you are satisfied, mark the exact position for Strips.
Remove it from its position, ensure that the surface is still
clean, remove the long film protecting the adhesive backing
and place Strips exactly as you marked. The long adhesive is
used to make the final placement of Strips.
6. Check that the door/window can be fully closed and opened
and that your Z-Wave controller detects the changes.
7. Keep the round magnet (B); since it can be used to wake up,
remove or reset Strips.
Enjoy Strips for years to come!
Strips-MaZw ENGLISH
ADD PLAN PLACE
C
Wake up
Wake up Strips manually for Z-Wave communication. Place the round
magnet (B) at the rounded edge. When the LED blinks, move the magnet
away. Repeat 3 times in total within 10 seconds.
Add/remove
Set your controller in add or remove mode (see your controller’s manual).
Follow the instruction above for Wake up. A long LED blink indicates that the
add/remove was successful.
Reset
You may reset Strips to factory default settings. Follow the instructions
for “Wake up” above, but on the 3rd repetition, leave the magnet at the
rounded edge for 10s. A long led signal indicates success.
A
1 short
blink
• User feedback during commands
• Specific event detected (ex. door opened)*
2 short For demo purposes (only if Strips is not added)
1 long User command successfully executed
5 short Error. ex. communication with controller failed
B
No Description Values Default
1
Notification
type (1 byte)
0: Binary Sensor report
1 : Notification report
2: Basic report
1
2
LED indication
(1 byte)
0: Specific event
indication (*) Off
1 : On
1
A) LED LIGHT SIGNALS B) CONFIGURATION PARAMETERS C) USER COMMANDS D) OTHER
Your Strips is delivered in auto-add mode.
Follow the process below to add Strips in your network.
1. Start the add mode on your Z-Wave controller.
See your controller’s manual.
2. Stay within range from the controller. Remove both magnets
from Strips. 1 long blink confirms the addition.
3. Your Z-wave controller application should now be able to
monitor your Strips sensor status.
4. Move the squared magnet (A) as shown in the pictures.
Check that your Z-Wave system indicates the status
correctly.
5. If your Z-Wave system doesn’t respond, you may need to
change Strips’ notification type from the controller.
FOLDFOLDFOLD
1
2
3
4
5
9
10
6
7
8
D
Association
Strips supports association group 1 (lifeline). Max 1 node.
Normally used to send Strips status to the Z-Wave controller.
Tamper
Strips will send a tampering alert if it detects that
someone tries to wake up or manipulate Strips.
GBS/INS 11 01 010 R1A
1 / 1

Z-Wave Sensative Strips Plus Ultra Thin Door/Window Contact Sensor Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document